 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MJ16110/D Designer'sTM Data Sheet MJ16110* MJW16110 * *Motorola Preferred Device NPN Silicon Power Transistors SWITCHMODE Bridge Series * * * * * * . . . specifically designed for use in half bridge and full bridge off line converters. Excellent Dynamic Saturation Characteristics Rugged RBSOA Capability Collector-Emitter Sustaining Voltage -- VCEO(sus) -- 400 V Collector-Emitter Breakdown -- V(BR)CES -- 650 V State-of-Art Bipolar Power Transistor Design Fast Inductive Switching: tfi = 25 ns (Typ) @ 100_C tc = 50 ns (Typ) @ 100_C tsv = 1 s (Typ) @ 100_C * Ultrafast FBSOA Specified * 100_C Performance Specified for: RBSOA Inductive Load Switching Saturation Voltages Leakages MAXIMUM RATINGS POWER TRANSISTORS 15 AMPERES 400 VOLTS 175 AND 135 WATTS IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II III I I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIII IIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII II II II IIIIIIIIIIIIIIIIIIIIIII IIII I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIII II I I I I II IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII II II III II IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII II I II II IIIIIIIIIIIIIIIIIIIIIII II IIIIIIIIIIIIIIIIIIIIIII II IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII II II III I II II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII II II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II III I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII II II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII I IIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII II II II IIIIIIIIIIIIIIIIIIIIIII IIII I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII II II IIIIIIIIIIIIIIIIIIIIIII Rating Symbol MJ16110 MJW16110 Unit Vdc Vdc Vdc Adc Adc Collector-Emitter Sustaining Voltage VCEO(sus) VCES 400 650 6 Collector-Emitter Breakdown Voltage Emitter-Base Voltage VEBO IC ICM IB IBM PD Collector Current -- Continuous -- Pulsed (1) Base Current -- Continuous -- Pulsed (1) Total Power Dissipation @ TC = 25_C @ TC = 100_C Derated above 25_C 15 20 10 15 175 100 1 135 54 1.09 Watts W/_C Operating and Storage Temperature TJ, Tstg - 65 to 200 - 55 to 150 CASE 1-07 TO-204AA (FORMERLY TO-3) MJ16110 _C THERMAL CHARACTERISTICS Thermal Resistance -- Junction to Case RJC TL 1 0.92 _C/W _C Maximum Lead Temperature for Soldering Purposes 1/8 from Case for 5 Seconds 275 CASE 340F-03 TO-247AE MJW16110 (1) Pulse Test: Pulse Width = 5 ms, Duty Cycle v 10%. Designer's Data for "Worst Case" Conditions -- The Designer's Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit curves -- representing boundaries on device characteristics -- are given to facilitate "worst case" design. Preferred devices are Motorola recommended choices for future use and best overall value. Designer's and SWITCHMODE are trademarks of Motorola Inc. REV 1 (c) Motorola, Inc. 1995 Motorola Bipolar Power Transistor Device Data 1 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I II I I I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I III I I I I IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I III I I I I IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I IIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III I I I I IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I I IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII I IIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I I I II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I IIIIIIIIIIIIIIIIIIII IIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIII I II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII III I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I IIIIIIIIIIIIIIIIIIII I III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII II I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII III I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III I I I I IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII II I I I I IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII II I I I I IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I I IIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III I I I IIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII MJ16110 MJW16110 (1) Pulse Test: Pulse Width = 300 s, Duty Cycle ELECTRICAL CHARACTERISTICS (TC = 25_C unless otherwise noted) SWITCHING CHARACTERISTICS DYNAMIC CHARACTERISTICS ON CHARACTERISTICS (1) OFF CHARACTERISTICS (1) Fall Time Storage Time Fall Time Storage Time Rise Time Delay Time Resistive Load (Table 2) Fall Time Crossover Storage Fall Time Crossover Storage Inductive Load (Table 1) Output Capacitance (VCE = 10 Vdc, IE = 0, ftest = 1 kHz) Dynamic Saturation DC Current Gain (IC = 15 Adc, VCE = 5 Vdc) Base-Emitter Saturation Voltage (IC = 10 Adc, IB = 2 Adc) (IC = 10 Adc, IB = 2 Adc, TC = 100_C) Collector-Emitter Saturation Voltage (IC = 5 Adc, IB = 0.5 Adc) (IC = 10 Adc, IB = 1.2 Adc) (IC = 10 Adc, IB = 2 Adc) (IC = 10 Adc, IB = 2 Adc, TC = 100_C) Emitter-Base Leakage (VEB = 6 Vdc, IC = 0) Collector Cutoff Current (VCE = 650 Vdc, RBE = 50 , TC = 100_C) Collector Cutoff Current (VCE = 650 Vdc, VBE(off) = 1.5 V) (VCE = 650 Vdc, VBE(off) = 1.5 V, TC = 100_C) Collector-Emitter Sustaining Voltage (Table 1) (IC = 20 mAdc, IB = 0) 2 IC = 10 A, IB1 = 1 A, VCC = 250 V, PW = 30 s, Duty Cycle = IC = 10 A, IB1= 1 A, VBE(off) = 5 V, VCE(pk) = 250 V Characteristic v2% v 2%. VBE(off) = 5 V TJ = 100_C _C IB2 = 2 A, RB2 = 4 TJ = 25_C _C VCEO(sus) VCE(dsat) VCE(sat) VBE(sat) Symbol Motorola Bipolar Power Transistor Device Data IEBO ICER ICEV Cob hFE tsv tsv td ts ts tfi tc tfi tc tr tf tf Min 400 See Figures 11, 12, and 13 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 6 1000 Typ 250 500 800 330 700 110 1.2 1.2 0.3 0.7 0.3 0.4 15 25 50 20 45 12 -- -- -- -- -- -- 100 1000 2000 1500 1000 Max 125 200 150 400 1.5 1.5 0.9 2.0 1.0 1.5 75 20 10 -- -- -- -- -- -- -- Adc Adc Adc Unit Vdc Vdc Vdc pF ns ns -- V MJ16110 MJW16110 TYPICAL STATIC CHARACTERISTICS VCE , COLLECTOR-EMITTER SATURATION VOLTAGE (VOLTS) 3 2 1 0.7 0.5 0.3 0.2 0.1 0.07 0.05 0.03 0.15 0.2 0.3 0.5 0.7 1 2 3 5 IC, COLLECTOR CURRENT (AMPS) IC/IB = 10 TJ = 100C TJ = 25C IC/IB = 5 7 10 15 TJ = 100C TJ = 25C 30 hFE, DC CURRENT GAIN 20 TJ = 100C TJ = 25C 10 TJ = - 55C 5 3 2 0.2 0.3 0.5 VCE = 5 V 3 1 2 5 IC, COLLECTOR CURRENT (AMPS) 10 20 Figure 1. DC Current Gain Figure 2. Collector-Emitter Saturation Voltage VCE , COLLECTOR-EMITTER VOLTAGE (VOLTS) TJ = 25C VBE, BASE-EMITTER VOLTAGE (VOLTS) 10 7 5 3 IC/IB = 5 & 10 2 1.5 1 0.7 0.5 TJ = 25C TJ = 100C 2 10 A 1 0.7 0.5 5A 0.2 0.1 0.1 IC = 3 A 0.2 0.5 0.7 1 2 5 7 10 7A 15 A 0.3 0.15 0.2 0.3 0.5 0.7 1 2 3 5 7 10 15 IB, BASE CURRENT (AMPS) IC, COLLECTOR CURRENT (AMPS) Figure 3. Collector-Emitter Saturation Region Figure 4. Base-Emitter Saturation Region 10K 5K 3K 2K 1K 500 300 200 100 50 30 20 10 0.1 TJ = 25C ftest = 1 kHz 0.3 0.5 1 3 5 10 30 50 100 300 600 1K VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) Cob Cib C, CAPACITANCE (pF) Figure 5. Capacitance Motorola Bipolar Power Transistor Device Data 3 MJ16110 MJW16110 TYPICAL INDUCTIVE SWITCHING CHARACTERISTICS IC/IB = 10, TC = 100C, VCE(pk) = 250 V 10K 7K 5K t sv, STORAGE TIME (ns) 3K 2K 1K 700 500 300 VBE(off) = 2 V VBE(off) = 5 V VBE(off) = 0 V IB2 = 2 (IB1) t c , CROSSOVER TIME (ns) 1K 700 500 300 200 100 70 50 30 20 100 1.5 10 1.5 IB2 = 2 (IB1) VBE(off) = 5 V VBE(off) = 2 V VBE(off) = 0 V 2 3 5 7 10 15 2 3 5 7 10 15 IC, COLLECTOR CURRENT (AMPS) IC, COLLECTOR CURRENT (AMPS) Figure 6. Storage Time Figure 7. Crossover Time t fi , COLLECTOR CURRENT FALL TIME (ns) 1K 700 500 200 100 70 50 30 20 10 1.5 VBE(off) = 0 V IB2 = 2 (IB1) VBE(off) = 2 V VBE(off) = 5 V 2 3 5 7 10 15 IC, COLLECTOR CURRENT (AMPS) Figure 8. Fall Time VCE(pk) 90% IC(pk) tfi tc tti I B2 , REVERSE BASE CURRENT (AMPS) IC(pk) 90% VCE(pk) IC tsv trv 10 9 8 7 6 5 4 3 2 1 0 0 1 2 3 4 VBE(off), REVERSE BASE VOLTAGE (VOLTS) 5 IC = 10 A TC = 25C IB1 = 2 A 1A VCE IB 90% IB1 10% VCE(pk) 10% IC(pk) 2% IC t, TIME Figure 9. Inductive Switching Measurements Figure 10. Peak Reverse Base Current 4 Motorola Bipolar Power Transistor Device Data MJ16110 MJW16110 Table 1. Inductive Load Switching Drive Circuit +15 1 F 150 100 100 F MTP8P10 MTP8P10 RB1 A MPF930 50 MUR105 MTP12N10 500 F 150 Voff *Tektronix AM503 *P6302 or Equivalent Scope -- Tektronix 7403 or Equivalent t1 (ICpk [ LcoilCC ) V T1 0V -V +V MJE210 1 F RB2 VCEO(sus) L = 10 mH RB2 = VCC = 20 Volts IC(pk) = 20 mA Inductive Switching L = 200 H RB2 = 0 VCC = 20 Volts RB1 selected for desired IB1 RBSOA L = 200 H RB2 = 0 VCC = 20 Volts RB1 selected for desired IB1 A *IB Vclamp VCC IC(pk) IC VCE(pk) VCE IB1 IB IB2 *IC T.U.T. 1N4246GP MPF930 +10 L T1 adjusted to obtain IC(pk) Note: Adjust Voff to obtain desired VBE(off) at Point A. Table 2. Resistive Load Switching +15 H.P. 214 OR EQUIV. P.G. RB = 8.5 50 td and tr *IB T.U.T. RL VCC *IC ts and tf 1 F 150 100 100 F MTP8P10 MTP8P10 RB1 A V(off) adjusted to give specified off drive MPF930 +10 V MPF930 50 MUR105 RB2 MTP12N10 VCC VCC Vin 0V tr 15 ns *Tektronix AM503 *P6302 or Equivalent 11 V RL IC IB 250 Vdc 25 10 A 1A IC IB1 IB2 RB1 RB2 RL 250 V 10 A 1.0 A Per Spec 15 Per Spec 25 Voff A *IB T.U.T. 500 F 150 MJE210 1 F *IC VCC RL VCE VCE(dsat) = DYNAMIC SATURATION VOLTAGE AND IS MEASURED FROM THE 90% POINT OF IB1 (t = 0) TO A MEASUREMENT POINT ON THE TIME AXIS (t1, t2 or t3 etc.) VCE , COLLECTOR-EMITTER VOLTAGE (VOLTS) 16 14 12 10 8 6 4 2 0 MAXIMUM TYPICAL 0.5 1 1.5 IB, BASE CURRENT (AMPS) 2 2.5 t = 2 s t = 1 s IC = 10 A 90% IB1 IB1 0 t1 t2 t3 t4 t, TIME t5 t6 t7 t8 0 Figure 11. Definition of Dynamic Saturation Measurement Figure 12. Dynamic Saturation Voltage Motorola Bipolar Power Transistor Device Data 5 MJ16110 MJW16110 DYNAMIC SATURATION VOLTAGE For bipolar power transistors low DC saturation voltages are achieved by conductivity modulating the collector region. Since conductivity modulation takes a finite amount of time, DC saturation voltages are not achieved instantly at turn-on. In bridge circuits, two transistor forward converters, and two transistor flyback converters dynamic saturation characteristics are responsible for the bulk of dynamic losses. The MJ16110 has been designed specifically to minimize these losses. Performance is roughly four times better than the original version of MJ16010. From a measurement point of view, dynamic saturation voltage is defined as collector-emitter voltage at a specific point in time after IB1 has been applied, where t = 0 is the 90% point on the IB1 rise time waveform, This definition is illustrated in Figure 11. Performance data was taken in the circuit that is shown in Figure 13. The 24 volt rail allows a Tektronix 2445 or equivalent scope to operate at 1 volt per division without input amplifier saturation. Dynamic saturation performance is illustrated in Figure 12. The MJ16110 reaches DC saturation levels in approximately 2 s, provided that sufficient base drive is provided. The dependence of dynamic saturation voltage upon base drive suggests a spike of IB1 at turn-on to minimize dynamic saturation losses, and also avoid overdrive at turn-off. However, in order to simulate worst case conditions the guaranteed dynamic saturation limits in this data sheet are specified with a constant level of IB1. + 24 Q1 MJ11012 1k 4 1k 10 k 7 1N5314 8 1N4111 100 F 2.4 20 W 100 1W 0.01 F 2.4 mH Q5 MTM8P08 10 F IC 47 1W 1.8 k IRFD9123 7 10 k 2 3 1 5 0.01 F 0.01 F Q3 IRFD113 6 Q2 MUR405 500 MUR405 Q6 MTP25N06 IB V CE 1N5831 U1 MC1455 6 100 pF (OSCILLATOR) 3 2 15 0.01 F Q4 IRFD9120 0.1 F 4 1N914 8 Figure 13. Dynamic Saturation Test Circuit GUARANTEED SAFE OPERATING AREA INFORMATION 20 50 IC, COLLECTOR CURRENT (AMPS) 20 10 5 3 2 1 0.5 0.3 0.2 0.1 0.05 0.03 0.02 0.01 TC = 25C IC, COLLECTOR CURRENT (AMPS) MJ16110 MJW16110 REGION II -- EXPANDED FBSOA USING MUR870 ULTRA-FAST RECTIFIER, SEE FIGURE 16 10 s 18 16 14 12 10 8 6 4 2 0 0 VBE(off) = 0 V 200 400 600 100 300 500 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) 700 VBE(off) = 1 to 5 V IC/IB1 = 5 TJ 100C 1 ms dc 100 ns II BONDING WIRE LIMIT THERMAL LIMIT SECONDARY BREAKDOWN LIMIT 1 23 5 10 20 30 50 100 200 300 500 1000 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) Figure 14. Forward Bias Safe Operating Area +15 1 F 150 100 100 F MTP8P10 Figure 15. Reverse Bias Safe Operating Area VCE (650 V MAX) 10 F MTP8P10 RB1 10 mH MUR870 MUR1100 MPF930 +10 MPF930 50 MUR105 RB2 MTP12N10 500 F 150 VOff MJE210 1 F Note: Test Circuit for Ultra-fast FBSOA Note: RB2 = 0 and VOff = - 5 Volts MUR105 T.U.T. Figure 16. Switching Safe Operating Area 6 Motorola Bipolar Power Transistor Device Data MJ16110 MJW16110 100 POWER DERATING FACTOR (%) SECOND BREAKDOWN DERATING 80 60 THERMAL DERATING MJ16110 MJW16110 40 20 0 0 40 80 120 TC, CASE TEMPERATURE (C) 160 200 Figure 17. Power Derating 1 0.7 0.5 0.3 0.2 0.1 0.07 0.05 0.03 0.02 0.01 0.01 0.02 SINGLE PULSE 0.02 0.03 0.05 0.1 0.2 0.3 0.5 1 23 5 t, TIME (ms) 10 20 30 50 100 r(t), EFFECTIVE TRANSIENT THERMAL RESISTANCE (NORMALIZED) D = 0.5 0.2 0.1 RJC(t) = r(t) RJC RJC = 1 or 0.92CW TJ(pk) - TC = P(pk) RJC(t) P(pk) 0.03 t1 t2 DUTY CYCLE, D = t1/t2 200 300 500 1000 Figure 18. Thermal Response SAFE OPERATING AREA INFORMATION FORWARD BIAS There are two limitations on the power handling ability of a transistor: average junction temperature and second breakdown. Safe operating area curves indicate IC - VCE limits of the transistor that must be observed for reliable operation; i.e., the transistor must not be subjected to greater dissipation than the curves indicate. The data in Figure 14 is based on TC = 25_C; T J(pk) is variable depending on power level. Second breakdown pulse limits are valid for duty cycles to 10% but must be derated when TC 25_C. Second breakdown limitations do not derate the same as thermal limitations. Allowable current at the voltages shown on Figure 14 may be found at any case temperature by using the appropriate curve on Figure 17. T J(pk) may be calculated from the data in Figure 18. At high case temperatures, thermal limitations will reduce the power that can be handled to values less than the limitations imposed by second breakdown. REVERSE BIAS For inductive loads, high voltage and high current must be sustained simultaneously during turn-off, in most cases, with the base-to-emitter junction reverse biased. Under these conditions the collector voltage must be held to a safe level at or below a specific value of collector current. This can be Motorola Bipolar Power Transistor Device Data accomplished by several means such as active clamping, RC snubbing, load line shaping, etc. The safe level for these devices is specified as Reverse Biased Safe Operating Area and represents the voltage-current condition allowable during reverse biased turn-off. This rating is verified under clamped conditions so that the device is never subjected to an avalanche mode. Figure 15 gives the RBSOA characteristics. SWITCHMODE DESIGN CONSIDERATIONS FBSOA Allowable dc power dissipation in bipolar power transistors decreases dramatically with increasing collector-emitter voltage. A transistor which safely dissipates 100 watts at 10 volts will typically dissipate less than 10 watts at its rated V (BR)CEO(sus). From a power handling point of view, current and voltage are not interchangeable (see Application Note AN875). TURN-ON Safe turn-on load line excursions are bounded by pulsed FBSOA curves. The 10 s curve applies for resistive loads, most capacitive loads, and inductive loads that are clamped by standard or fast recovery rectifiers. Similarly, the 100 ns curve applies to inductive loads which are clamped by ultra- fast recovery rectifiers, and are valid for turn-on crossover times less than 100 ns (AN952). 7 MJ16110 MJW16110 SWITCHMODE DESIGN CONSIDERATIONS (Cont.) At voltages above 75% of V (BR)CEO(sus), it is essential to provide the transistor with an adequate amount of base drive VERY RAPIDLY at turn-on. More specifically, safe operation according to the curves is dependent upon base current rise time being less than collector current rise time. As a general rule, a base drive compliance voltage in excess of 10 volts is required to meet this condition (see Application Note AN875). TURN-OFF A bipolar transistor's ability to withstand turn-off stress is dependent upon its forward base drive. Gross overdrive violates the RBSOA curve and risks transistor failure. For this reason, circuits which use fixed base drive are more likely to fail at light loads due to heavy overdrive (see Application Note AN875). OPERATION ABOVE V(BR)CEO(sus) When bipolars are operated above collector-emitter breakdown, base drive is crucial. A rapid application of adequate forward base current is needed for safe turn-on, as is a stiff negative bias needed for safe turn-off. Any hiccup in the base-drive circuitry that even momentarily violates either of these conditions will likely cause the transistor to fail. BAKER CLAMPS Many unanticipated pitfalls can be avoided by using Baker Clamps. MUR105 and MUR170 diodes are recommended for base drives less than 1 amp. Similarly, MUR405 and MUR470 types are well-suited for higher drive requirements (see Article Reprint AR131). Therefore, it is important to design the driver so that its output is negative in the absence of anything but a clean crisp input signal (see Application Note AN952). RBSOA Reversed Biased Safe Operating Area has a first order dependency on circuit configuration and drive parameters. The RBSOA curves in this data sheet are valid only for the conditions specified. For a comparison of RBSOA results in several types of circuits (see Application Note AN951). DESIGN SAMPLES Transistor parameters tend to vary much more from wafer lot to wafer lot, over long periods of time, than from one device to the next in the same wafer lot. For design evaluation it is advisable to use transistors from several different date codes. 8 Motorola Bipolar Power Transistor Device Data MJ16110 MJW16110 PACKAGE DIMENSIONS A N C -T- E D U V 2 2 PL SEATING PLANE K M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. ALL RULES AND NOTES ASSOCIATED WITH REFERENCED TO-204AA OUTLINE SHALL APPLY. 0.13 (0.005) L G 1 TQ M Y M -Y- H B -Q- 0.13 (0.005) M TY M DIM A B C D E G H K L N Q U V INCHES MIN MAX 1.550 REF --- 1.050 0.250 0.335 0.038 0.043 0.055 0.070 0.430 BSC 0.215 BSC 0.440 0.480 0.665 BSC --- 0.830 0.151 0.165 1.187 BSC 0.131 0.188 MILLIMETERS MIN MAX 39.37 REF --- 26.67 6.35 8.51 0.97 1.09 1.40 1.77 10.92 BSC 5.46 BSC 11.18 12.19 16.89 BSC --- 21.08 3.84 4.19 30.15 BSC 3.33 4.77 STYLE 1: PIN 1. BASE 2. EMITTER CASE: COLLECTOR CASE 1-07 TO-204AA (FORMERLY TO-3) ISSUE Z NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. DIM A B C D E F G H J K L P Q R U V MILLIMETERS MIN MAX 20.40 20.90 15.44 15.95 4.70 5.21 1.09 1.30 1.50 1.63 1.80 2.18 5.45 BSC 2.56 2.87 0.48 0.68 15.57 16.08 7.26 7.50 3.10 3.38 3.50 3.70 3.30 3.80 5.30 BSC 3.05 3.40 INCHES MIN MAX 0.803 0.823 0.608 0.628 0.185 0.205 0.043 0.051 0.059 0.064 0.071 0.086 0.215 BSC 0.101 0.113 0.019 0.027 0.613 0.633 0.286 0.295 0.122 0.133 0.138 0.145 0.130 0.150 0.209 BSC 0.120 0.134 0.25 (0.010) M -Q- TBM -T- E -B- U C 4 L A R 1 2 3 K P -Y- F D 0.25 (0.010) M V G H J YQ S STYLE 3: PIN 1. 2. 3. 4. BASE COLLECTOR EMITTER COLLECTOR CASE 340F-03 TO-247AE ISSUE E Motorola Bipolar Power Transistor Device Data 9 MJ16110 MJW16110 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 10 Motorola Bipolar Power Transistor Device Data *MJ16110/D* MJ16110/D |
Price & Availability of MJW16110
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |