|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
MOTOROLA SEMICONDUCTOR TECHNICAL DATA 9-Bit Latch ECL/TTL Translator The MC10H/100H603 is a 9-bit, dual supply ECL to TTL translator. Devices in the Motorola 9-bit translator series utilize the 28-lead PLCC for optimal power pinning, signal flow-through and electrical performance. The devices feature a 48 mA TTL output stage, and AC performance is specified into both a 50 pF and 200 pF load capacitance. Latching is controlled by Latch Enable (LEN), and Master Reset (MR) resets the latches. A HIGH on OEECL sends the outputs into the high impedance state. All control inputs are ECL level. The 10H version is compatible with MECL 10H ECL logic levels. The 100H version is compatible with 100K levels. * * * * * * * 9-Bit Ideal for Byte-Parity Applications 3-State TTL Outputs Flow-Through Configuration Extra TTL and ECL Power Pins to Minimize Switching Noise Dual Supply 6.0 ns Max Delay into 50 pF, 12 ns into 200 pF (all outputs switching) PNP TTL Inputs for Low Loading MC10H603 MC100H603 FN SUFFIX PLASTIC PACKAGE CASE 776-02 PIN NAMES PIN GND VCCE VCCT VEE D0 - D8 Q0 - Q8 OEECL LEN MR FUNCTION TTL Ground (0 V) ECL VCC (0 V) TTL Supply (+ 5.0 V) ECL Supply (- 5.2 / - 4.5 V) Data Inputs (ECL) Data Outputs (TTL) 3-State Control (ECL) Latch Enable (ECL) Master Reset (ECL) LOGIC SYMBOL OEECL D0 DQ EN DQ EN DQ EN DQ EN DQ EN DQ EN DQ EN DQ EN DQ EN Q0 TRUTH TABLE D LEN L L H X X MR L L L H X OEECL L L L L H Q L H Q0 L Z D1 Q1 D2 Q2 L H X X X D3 Q3 Pinout: 28-Lead PLCC (Top View) Q4 TTL Q4 Q3 26 27 28 ECL D4 Q5 GND VCCT Q6 GND Q7 Q8 25 24 23 22 21 20 19 18 17 16 15 2 3 4 5 6 7 8 9 10 11 14 13 12 D5 Q5 D8 D7 VCCE D6 D5 D4 D3 D6 Q6 VCCT Q2 D7 Q7 GND Q1 D8 LEN MR Q8 Q0 MR LEN OEECL VEE D0 D1 D2 3/93 (c) Motorola, Inc. 1996 2-311 REV 5 MC10H603 MC100H603 DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% (10H version); VEE = - 4.2 V to - 5.5 V (100H version) 0C Symbol S bl IEE ICCH ICCL ICCZ IOS IOZH IOZL Output Short Circuit Current Output Disable Current HIGH LOW Parameter P Power Supply Current ECL TTL Min - 45 80 80 80 -100 Max - 63 110 110 110 - 225 50 - 50 Min - 45 80 80 80 -100 25C Max - 64 110 110 110 - 225 50 - 50 Min - 45 80 80 80 -100 75C Max - 68 110 110 110 - 225 50 - 50 Unit Ui mA mA mA mA mA A A VOUT = 0 V VOUT = 2.7 V VOUT = 0.5 V Condition C di i AC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% (10H version); VEE = - 4.2 V to - 5.5 V (100H version) 0C Symbol S bl tPLH tPHL Parameter P Propagation Delay to Output D LEN MR ts th tw(L) tPLZ tPHZ tPZL tPZH tR tF Set-Up Time, D to LEN Hold Time, D to LEN LEN Pulse Width, LOW Output Disable Time Output Enable Time Output Rise/Fall Time 1.0 V - 2.0 V Min 3.0 6.4 3.5 7.0 3.0 6.0 1.5 0.8 2.0 2.5 4.2 2.0 4.0 0.2 0.2 6.5 13 5.0 10 1.2 3.0 Max 6.0 12 6.5 13 6.0 12 Min 3.0 6.4 3.5 7.0 3.0 6.0 1.5 0.8 2.0 2.5 4.2 2.0 4.0 0.2 0.2 6.5 13 5.0 10 1.2 3.0 25C Max 6.0 12 6.5 13 6.0 12 Min 3.0 6.4 3.5 7.0 3.0 6.0 1.5 0.8 2.0 2.5 4.2 2.0 4.0 0.2 0.2 6.5 13 5.0 10 1.2 3.0 75C Max 6.0 12 6.5 13 6.0 12 Unit Ui ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns CL = 50 pF CL = 200 pF CL = 50 pF CL = 200 pF CL = 50 pF CL = 200 pF Condition C di i CL = 50 pF CL = 200 pF CL = 50 pF CL = 200 pF CL = 50 pF CL = 200 pF MOTOROLA 2-312 MECL Data DL122 -- Rev 6 MC10H603 MC100H603 10H ECL DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% 0C Symbol S bl IIH IIL VIH VIL Parameter P Input HIGH Current Input LOW Current Input HIGH Voltage Input LOW Voltage Min 0.5 -1170 -1950 - 840 -1480 Max 225 0.5 -1130 -1950 - 810 -1480 Min 25C Max 145 0.5 -1070 -1950 - 735 -1450 Min 75C Max 145 Unit Ui A A mV Condition C di i 100H ECL DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 4.2 V to - 5.5 V 0C Symbol S bl IIH IIL VIH VIL Parameter P Input HIGH Current Input LOW Current Input HIGH Voltage Input LOW Voltage Min 0.5 -1165 -1810 - 880 -1475 Max 225 0.5 -1165 -1810 - 880 -1475 Min 25C Max 145 0.5 -1165 -1810 - 880 -1475 Min 75C Max 145 Unit Ui A A mV Condition C di i TTL DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% (10H version); VEE = - 4.2 V to - 5.5 V (100H version) 0C Symbol S bl VIH VIL IIH IIL VIK VOH VOL Parameter P Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current Input Clamp Voltage Output HIGH Voltage Output LOW Voltage 2.5 2.0 0.55 Min 2.0 0.8 20 100 - 0.6 -1.2 2.5 2.0 0.55 Max Min 2.0 0.8 20 100 - 0.6 -1.2 2.5 2.0 0.55 25C Max Min 2.0 0.8 20 100 - 0.6 -1.2 75C Max Unit Ui V V A mA V V V V VIN = 2.7 V VIN = 7.0 V VIN = 0.5 V IIN = -18 mA IOH = - 3.0 mA IOH = -15 mA IOL = 48 mA Condition C di i MECL Data DL122 -- Rev 6 2-313 MOTOROLA MC10H603 MC100H603 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D B -N- Y BRK U D Z -L- -M- 0.007 (0.180) M 0.007 (0.180) M T L-M S N S S T L-M N S W 28 1 D X VIEW D-D G1 0.010 (0.250) S T L-M S N S V A Z R C 0.007 (0.180) 0.007 (0.180) M T L-M T L-M S N N S H 0.007 (0.180) M T L-M S N S M S S E 0.004 (0.100) G G1 0.010 (0.250) S K1 J -T- VIEW S SEATING PLANE K F VIEW S 0.007 (0.180) M T L-M S N S T L-M S N S NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10_ 0.410 0.430 0.040 --- MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10_ 10.42 10.92 1.02 --- MOTOROLA 2-314 MECL Data DL122 -- Rev 6 MC10H603 MC100H603 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 MECL Data DL122 -- Rev 6 2-315 *MC10H603/D* MC10H603/D MOTOROLA |
Price & Availability of MC100H603 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |