 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ICs for Communications High Voltage Subscriber Line IC HV-SLIC PEB/F 4065 Version 3.0 Data Sheet 03.98 DS 1 ht tp : Se//ww mw ico .s nd iem uc en to s. r/ de / PEB/F 4065 Revision History: Previous Version: Page (in previous Version) Page (in current Version) Current Version: 03.98 01.96 Subjects (major changes since last revision) SLICOFI(R) is a registered trademark of SIEMENS AG. For questions on technology, delivery and prices please contact the Semiconductor Group Offices in Germany or the Siemens Companies and Representatives worldwide: see our webpage at http:/ /www.siemens.de/Semiconductor/address/address.htm. Edition 03.98 Published by Siemens AG, HL SP, Balanstrae 73, 81541 Munchen (c) Siemens AG 1998. All Rights Reserved. Attention please! As far as patents or other rights of third parties are concerned, liability is only assumed for components, not for applications, processes and circuits implemented within components or assemblies. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Siemens Office, Semiconductor Group. Siemens AG is an approved CECC manufacturer. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components1 of the Semiconductor Group of Siemens AG, may only be used in life-support devices or systems2 with the express written approval of the Semiconductor Group of Siemens AG. 1 A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. 2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered. PEB/F 4065 Table of Contents 1 1.1 1.2 1.3 2 2.1 2.2 2.3 2.4 2.5 3 Page Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Thermal Resistances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Electrical Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 AC-Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Semiconductor Group 3 1998-03-01 High Voltage Subscriber Line IC HV-SLIC PEB/F 4065 Version 1.1 1 Overview SPT The High Voltage Subscriber Line IC PEB 4065 is a rugged and reliable interface between the telephone line and the SLICOFI, a low voltage Subscriber Line Interface and Codec Filter IC. It is fabricated in a Smart Power Technology offering a breakthrough voltage of at least 170 V. P-DSO-20-5 The PEB 4065 provides battery feeding between - 24 V and - 80 V and internal ringing injection with a differential ring voltage up to 85 Vrms. In order to achieve these high amplitudes an auxiliary positive battery voltage is used during ringing. This voltage can also be applied in order to drive very long telephone lines. The SLIC is designed for a voltage feeding - current sensing line interface concept and provides sensing of transversal and longitudinal current on both wires. A power-down mode offers reduced power consumption at full functionality; in the power denial mode the device is switched off turning the line outputs to a high impedance state. 1.1 * * * * * * Features High voltage line feeding Internal ring and metering signal injection Sensing of transversal and longitudinal line current Reliable 170 V Smart Power Technology Battery voltage - 24 V ... - 80 V Boosted battery mode for long telephone lines and up to 85 Vrms balanced ringing * Polarity reversal * Small P-DSO-20-5 power package Type PEB/F 4065 Semiconductor Group Ordering Code on request 4 Package P-DSO-20-5 1998-03-01 PEB/F 4065 Overview 1.2 Functional Description VH BGND Supply Switch RING a Vab VHINT Buffer Differential I/V-Converter Buffer Control C1 C2 V/I Converter V2W TIP b Reference PDN Current sensor VBAT Supply T L VBAT VBIM AGND VSS VDD ITB10371 Figure 1 Block Diagram The PEB 4065 supports AC and DC control loops based on feeding a voltage Vab to the line and sensing the transversal line current Iab (Figure 2). It converts a unipolar input voltage V2W into a differential output voltage Vab with an AC receiving gain of Gr = VabAC/V2WAC = 40. This is accomplished by converting the input voltage to a current which is used to transpose the low voltage signals of the interface to the high voltage line feeding section. This current is reconverted to two voltages of opposite phase which are referenced to the positive and negative supply voltage, respectively. Thus the differential DC line-voltage in all normal polarity modes except ringing is related to the input voltage by VabDC = VBAT - VHINT + Vfix - 40 x V2WDC VBAT negative battery voltage VHINT internal positive supply voltage Vfix internal voltage drop of supply filter (appr. 2 V). Depending on the operation mode, VHINT is switched either to VH (VHINT = VH - 1 V) or to BGND (VHINT = - 0.5 V) via the supply switch. Semiconductor Group 5 1998-03-01 PEB/F 4065 Overview Controlled by C2, the polarity of Vab can be reversed and the DC-line-voltage then is VabDC = - (VBAT - VHINT + Vfix - 40 x V2WDC). The transversal and longitudinal currents are measured in the buffers and scaled images are provided at the IT and IL pin, respectively: IT = (Ia + Ib)/100 = Iab/50 IL = - (Ia - Ib)/100 = - ILong/50. The PEB 4065 operates in four modes controlled by ternary logic signals at the C1 and C2 input. Additionally, in the active modes a polarity reversal of the output voltage can be programmed (see Table 1). Power down (PD): Power consumption is reduced by decreasing bias current levels. All functions operate at some small performance reductions. In this mode each of the line outputs can be programmed to show high impedance. HI b switches off the TIP buffer, while the current through the RING output still can be measured by IT or IL. Programming HI a reverses the polarity and switches off the RING buffer. Conversation (CONV): This is the regular transmit and receive mode for voiceband and teletax. The line driving section is operated between VBAT and BGND. Boosted battery (BB): In order to drive longer telephone lines an auxiliary positive battery voltage VH is used, enabling a higher DC-voltage across the line. Ringing (RING): This mode also uses the auxiliary voltage VH in order to provide a balanced ring signal of up to 85 Vrms. The ring tone without any DC-component has to be switched to the V2W input. Internally a DC-voltage is superimposed. This voltage is proportional to the total supply voltage VH - VBAT and amounts to typically 23 V at VH - VBAT = 120 V. The current sensing functions are available for ring trip detection. The Power Denial (PDN) state is intended to reduce power consumption of the linecard to a minimum: the PEB 4065 is switched off completely by connecting the PDN pin to VDD, no operation is available. With respect to the output impedance of TIP and RING two PDN-modes have to be distinguished. A resistive one (PDNR) provides a connection of 15 k each from TIP to BGND and RING to VBAT, respectively, while the outputs of the buffers show high impedance (Figure 3). The other mode (PDNH) offers high impedance at TIP and RING. It is entered when, in addition to connecting PDN to VDD, the programming inputs C1, C2 are tied to VIL. All other combinations of C1, C2 yield the resistive power denial state PDNR. Semiconductor Group 6 1998-03-01 PEB/F 4065 Overview Table 1 Programming of Operation Modes C2 (Pin 13) VIL C1 (Pin 12) VIZ RING NP BB NP CONV NP VIH HI a RP HI b NP PD NP VIL VIZ VIH RING RP BB RP CONV RP RP...Reverse Polarity NP HI a RP HI b NP Normal Polarity Ring wire set to high impedance Tip wire set to high impedance Buffer Long a RING ZL 2 Vab ab Buffer ZL 2 ~ ~ b ab = ( a + b ) /2 Long = ( a - b ) /2 TIP Long ITS10372 Figure 2 Definition of Output Current Directions Semiconductor Group 7 1998-03-01 PEB/F 4065 Overview BGND PDNH PDNR HIZ R TG 15 k TIP HIZ RING R RB 15 k PDNH PDNR VBAT ITS10373 Figure 3 TIP and RING Impedance in Power Denial Semiconductor Group 8 1998-03-01 PEB/F 4065 Overview 1.3 Pin Description P-DSO-20-5 (11 mm) V BAT V SS L T AGND C2 C1 AGND PDN V BAT 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 ITP10374 V BAT RING TIP N.C. VH BGND V DD V 2W V BIM V BAT Due to reverse bending of the leads, the numbering of the pins is also reversed. Figure 4 Table 2 Pin No. Pin Configuration (top view) Pin Definition and Functions Symbol Type Function Input (I) Output (O) Supply O Negative battery supply voltage (- 24 ... - 80 V), referred to BGND Subscriber loop connection, negative wire in normal polarity; direction of positive Ia current out of this pin Subscriber loop connection, more positive wire in normal polarity; direction of positive Ib current into this pin Not connected Auxiliary positive battery supply voltage (0 ... + 90 V) used in ringing and boosted battery mode Battery ground: TIP, RING, VBAT and VH refer to this pin Positive supply voltage (+ 5 V), referred to AGND 9 1998-03-01 1, 10, 11, VBAT 20 2 RING 3 TIP O 4 5 - N.C. Supply VH 6 7 BGND Supply Supply VDD Semiconductor Group PEB/F 4065 Overview Table 2 Pin No. Pin Definition and Functions (cont'd) Symbol Type Function Input (I) Output (O) I Two wire input voltage; multiplied by + 20 and - 20, respectively, it appears at the TIP and RING outputs Down scaled image of the total supply voltage (VHINT - VBAT); scaling factor 40 Power denial, reference output when connected to ground via a resistor, switches the device off when connected to VDD Analog ground: VDD, VSS and all signal and control pins with exception of TIP and RING refer to AGND Ternary logic input, controlling the operation mode; in case of thermal overload this pin sinks a current of typ. 550 A Ternary logic input, controlling the operation mode Current output representing the transversal current scaled down by 50; In normal polarity this pin sinks the IT current. Current output representing the longitudinal current scaled down by 50; For Ilong flowing out of TIP and RING this pin sinks the IL current. Negative supply voltage (- 5 V), referred to AGND 8 V2W 9 12 VBIM PDN O I/O 13, 16 14 AGND C1 Supply I/O 15 17 C2 I O IT 18 IL O 19 VSS Supply Semiconductor Group 10 1998-03-01 PEB/F 4065 Electrical Characteristics 2 2.1 Table 3 Parameter Battery voltage Auxiliary supply voltage Symbol Limit Values min. max. 0.5 90 160 170 5.5 0.4 0.5 150 V V V V V V V C referred to BGND referred to BGND - - referred to AGND referred to AGND - - - - - - - - Human body model - 90 - 0.5 - - Unit Condition Electrical Characteristics Absolute Maximum Ratings VBAT VH Total battery supply VH - VBAT voltage, continuously VH - VBAT Total battery supply voltage, pulse < 1 ms VDD supply voltage VSS supply voltage Ground voltage difference Input voltages Voltages on current outputs Voltages on PDN RING, TIP voltages, continuously RING, TIP voltages, pulse < 1 ms1) RING, TIP voltages, 1) pulse < 1 s VDD - 0.4 VSS - 5.5 VBGND - VAGND - 0.5 - Junction temperature Tj V2W, VC1, VC2 VIT, VIL VPDN Va, Vb Va, Vb Va, Vb VSS - 0.3 - 3.5 - 0.3 VDD + 0.3 V VDD + 0.3 V VDD + 0.3 V VBAT - 0.3 VH + 0.3 V VBAT - 10 VH + 10 VBAT - 30 VH + 30 - 1 V V kV ESD-voltage, all pins - 1) See Test Figure 10. Note: Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. Semiconductor Group 11 1998-03-01 PEB/F 4065 Electrical Characteristics 2.2 Table 4 Parameter Battery voltage Auxiliary supply voltage Total battery supply voltage Symbol Limit Values min. max. - 24 85 150 5.25 - 4.75 0.3 70 85 3 + 3.2 0 V V V V V V C C V V V referred to BGND referred to BGND - referred to AGND referred to AGND - PEB 4065 PEF 4065 - RING CONV, PD, BB - 80 5 - 4.75 - 5.25 - 0.3 0 - 40 -3 - 3.2 - 3.2 Unit Condition Operating Range VDD supply voltage VSS supply voltage Ground voltage difference Ambient temperature Voltage compliance IT, IL Input range V2W VBAT VH VH - VBAT VDD VSS - Tamb VIT, VIL V2W Note: In the operating range the functions given in the circuit description are fulfilled. 2.3 Table 5 Parameter Junction to case Junction to ambient Symbol Limit Values 5 20 Unit K/W K/W Condition - with heatsink, typ. Thermal Resistances Rth, jC Rth, jA Semiconductor Group 12 1998-03-01 PEB/F 4065 Electrical Characteristics 2.4 Electrical Parameters Min/max values are valid within the full operating range. If PEB- and PEF-specifications are different, both values can be found in the respective column. Testing is performed according to the test figures with external circuitry as depicted in Figure 4. Unless otherwise stated, load impedance RL = 600 . Test temperatures are 25 and 70 C for PEB, - 40, 25 and 85 C for PEF-type (without heatsink). DC line voltages refer to VBAT = - 70 V and VH = + 60 V. Table 6 No. Supply Currents and Power Dissipation Symbol Mode Limit Values min. typ. Power Denial 1. 2. 3. 4. max. PEB/PEF 120/150 120/150 250/300 30 120 10 Unit Test Fig. Parameter VDD current VSS current VBAT current VH current IDD ISS IBAT IH PDNH, PDNR PDNH PDNR PDNH PDNR PDNH, PDNR PD PD PD PD PD - - - - 50 50 150 10 50 1 A A A A 1 1 1 1 Power Down 5. 6. 7. 8. 9. V2W = - 0.5 V1) IDD ISS IBAT IH PQ - - - - - 0.5 0.3 3.3 1 - 1.0 0.4 4.3/4.4 10 315 mA mA mA A 1 1 1 1 VDD current VSS current VBAT current VH current Quiescent power dissipation mW 1 Conversation, Normal and Reverse Polarity 10. 11. 12. 13. 14. V2W = - 0.5 V1) - - - - - 0.8 0.4 4.0 1 - 1.0/1.1 0.5/0.6 5.8/5.9 10 420 mA mA mA A 1 1 1 1 VDD current VSS current VBAT current VH current Quiescent power dissipation IDD ISS IBAT IH PQ CONV CONV CONV CONV CONV mW 1 Semiconductor Group 13 1998-03-01 PEB/F 4065 Electrical Characteristics Table 6 No. Supply Currents and Power Dissipation (cont'd) Symbol Mode Limit Values min. typ. Boosted Battery Mode Normal and Reverse Polarity 15. 16. 17. 18. 19. max. PEB/PEF 1.0 2.0 6.1/6.2 4.8 740 Unit Test Fig. Parameter V2W = - 0.5 V1) mA mA mA mA 1 1 1 1 VDD current VSS current VBAT current VH current Quiescent power dissipation IDD ISS IBAT IH PQ BB BB BB BB BB - - - - - 0.8 1.7 4.0 3.0 - mW 1 Ringing Mode Normal and Reverse Polarity 20. 21. 22. 23. 24. 1) V2W = 0 V - - - - - 2.3 2.8 8.8 7.1 2.6 3.2 12/12.5 10 mA mA mA mA 1 1 1 1 VDD current VSS current VBAT current VH current Quiescent power dissipation IDD ISS IBAT IH PQ RING RING RING RING RING 1300 1500 mW 1 IBAT and IH depend on the value of V2W: IBAT (V2W) = IBAT(0) + |V2W|/440 typ. (PD, CONV, BB) IH (V2W) = IH(0) + |V2W|/440 typ. (BB) Semiconductor Group 14 1998-03-01 PEB/F 4065 Electrical Characteristics Table 7 DC-Characteristics Symbol Mode Limit Values min. PEB/ PEF Line Termination TIP, RING 25. Power down DC line voltage 26. 27. Conversation |Vab,DC| DC line voltage 28. 29. 30. Ringing DC line voltage 31. Output current limit |Vab,DC| |Ia,max|, |Ib,max| |Vab,DC| PD 46 49 52 V 2 typ. max. PEB/ PEF Unit Test Test Condition Fig. No. Parameter V2W = - 0.5 V PD - 14 - 11 66.5 -8 68.5 V V 2 V2W = - 2 V V2W = 0 V CONV 65 CONV 46.6 CONV - 14 RING 22.1 47.8 48.8 V V2W = - 0.5 V - 12.2 - 10.4 V 25 - - 15 27.7 130 130/ 135 V mA mA 2 3 V2W = - 2 V V2W = 0 V V2W = - 0.5 V Va, Vb acc. to Test Figure 3 9 PD 85/80 others 90/85 PDNR 12/11 RTG 32. Loop open resistance TIP to BGND RRB 33. Loop open resistance RING to VBAT 34. Power denial ILeak,a output leakage current 35. 36. High impedance output leakage current 37. 18/19 k Ib = 2 mA PDNR 12/11 15 18/19 k Ia = 2 mA PDNH - 30 - 30 A - VBAT < Va < VH ILeak,b ILeak,a HI a - 30 - 30 - - 30 30 A A - VBAT < Va < VH VBAT < Va < VH-3 Ileak,b HI b - 30 - 30 A VBAT < Vb < VH-3 Semiconductor Group 15 1998-03-01 PEB/F 4065 Electrical Characteristics Table 7 DC-Characteristics (cont'd) Symbol Mode Limit Values min. PEB/ PEF Reference Voltage Outputs PDN, VBIM 38. Output voltage on PDN typ. max. PEB/ PEF 1.35 Unit Test Test Condition Fig. No. Parameter Vref all 1.15 1.25 V 1 - 39. Battery image VBIM voltage 40. Two-wire Input V2W 41. Input current 42. Input capacitance 43. IT output current 44. 45. 46. 47. IL output current 48. 49. 50. |IL| CONV, - 1.75 - 1.7 PD BB, RING - 1.65 V V 1 - - 3.25 - 3.18 - 3.1 I2W - all - - 30 - - - 30 20 A pF - - - 3.2 V < V2W < 3.2 V - Current Outputs IT, IL |IT| PD, - CONV PD, 380 CONV CONV 0.95 RING PD, - CONV PD, CONV PD, 65 CONV CONV 180 - - 15 420 1.05 20 30 30 135 320 A A mA A A A A A 2 2 V2W = - 0.5 V Ia = Ib = 0 Ia = Ib = 20 mA1) Ia = Ib = 50mA1) Ia = Ib = 0 Ia = Ib = 0 Ia = Ib = 20 mA1) Ia = 15 mA, Ib = 25 mA Ia = 37.5 mA, Ib = 62.5 mA Semiconductor Group 16 1998-03-01 PEB/F 4065 Electrical Characteristics Table 7 DC-Characteristics (cont'd) Symbol Mode Limit Values min. PEB/ PEF Control Inputs C1, C2 51. H-input voltage 52. Z-input voltage 53. L-input voltage 54. Input leakage current 55. Thermal overload current C1 typ. max. PEB/ PEF - 0.8 -2 5 Unit Test Test Condition Fig. No. Parameter VIH VIZ VIL ILeak all all all all 2 - 0.8 - -5 - - - - V V V A - - - - - - - - 5 V < VC1(2) < + 5 V Itherm all 500 550 - A - VC1 = - 3.2 V Tjoff 56. Switching Temperature Tjon (guaranteed by design) 1) all all - - 165 145 - - C C - - - - Polarity of Ia and Ib is reversed for measurement in reverse polarity mode Note: The listed characteristics are ensured over the operating range of the integrated circuit. Typical characteristics specify mean values expected over the production spread. If not otherwise specified, typical characteristics apply at TA = 25 C and the given supply voltage. Semiconductor Group 17 1998-03-01 PEB/F 4065 Electrical Characteristics 2.5 Table 8 No. Parameter Symbol Mode min. Limit Values typ. max. PEB/ PEF Unit Test Test Condition Fig. AC-Characteristics (Normal and reverse polarity unless otherwise stated) Line Termination TIP, RING Receive gain 57. 58. 59. Gain flatness dGr (guaranteed by design) 60. Gain tracking dGr (guaranteed by design) 61. Total harmonic distortion Vab Teletax distortion 62. 63. THD Gr CONV, 31.92 32.04 BB CONV 31.88 32.04 CONV, - 0.05 - BB CONV - 0.2 - 32.16 32.2 0.05 dB dB dB - 4 V2W,AC = 50 mVrms f = 1015 Hz Iab = 20 mA Iab = 50 mA 300 Hz < f < 3400 Hz V2W,AC = 50 mVrms 3 dBm0 > Vab > - 20 dBm0 f = 1015 Hz 0.2 dB - CONV - - 0.3 % 4 V2W,AC = 50 mVrms f = 1015 Hz Iab = 20 mA f = 16 kHz RL = 200 Iab = 50 mA Vab,AC = 2 Vrms Vab,AC = 5 Vrms Iab = 0 mA, Vab = 55 V Vab,AC = 2 Vrms Iab = 30 mA Vlong = 3 Vrms 300 Hz < f < 3.4 kHz Iab = 30 mA V2W,AC = 150 mVrms 300 Hz < f < 3.4 kHz Iab = 30 mA THDTTX CONV 5 - - - - 3 3 % % 64. 65. Psophometric NP, Vab noise 66. Longitudinal LTRR to transversal rejection ratio Vlong/Vab TLRR 67. Transversal to longitudinal rejection ratio Vab/Vlong - CONV - - - 5 - 75 - % dBmp 4 dB 6 CONV 61/58 - CONV 50 - - dB 7 Semiconductor Group 18 1998-03-01 PEB/F 4065 Electrical Characteristics Table 8 (cont'd) Symbol Mode min. Limit Values typ. max. PEB/ PEF Unit Test Test Condition Fig. No. Parameter Power supply PSRR rejection ratio 68. VBAT/Vab CONV, 33 40 BB PD 30/28 - BB 33/30 40 50 50 25 - - - - - - - dB dB dB dB dB dB 4 300 Hz < f < 3.4 kHz VSupply,AC = 100 mVp Iab = 30 mA 69. VH/Vab 70. VDD/Vab 71. VSS/Vab 72. Ringing voltage CONV, 33 BB CONV, 33 BB VRING RING 67 Vrms, 8 diff RL = 1 k CL = 1 F f = 66 Hz V2W = 1.7 Vrms VH = 80 V f = 20 Hz V2W = 2.2 Vrms f = 66 Hz V2W = 1.7 Vrms V2W = 50 mVrms f = 1015 Hz Iab = 20 mA Iab = 50 mA 73. Ringing voltage with extended VH 74. Ringing distortion Transversal current ratio 75. 76. 77. Gain flatness dGit (guaranteed by design) 78. Gain tracking dGit (guaranteed by design) 79. Total harmonic distortion VIT THD, IT THD RING 84 - - Vrms, 8 diff % 8 - - 4 Transversal Current Output IT Git CONV, 33.89 33.98 BB CONV 33.89 33.98 CONV, - 0.05 - BB CONV - 0.2 - 34.07 34.07 0.05 dB dB dB - 4 300 Hz < f < 3400 Hz V2W,AC = 50 mVrms Iab = 20 mA 3 dBm0 > Vab > - 20 dBm0 f = 1015 Hz V2W,AC = 50 mVrms f = 1015 Hz Iab = 15 mA 0.2 dB - CONV - 0.01 0.3 % 4 Semiconductor Group 19 1998-03-01 PEB/F 4065 Electrical Characteristics Table 8 (cont'd) Symbol Mode min. Limit Values typ. max. PEB/ PEF - 100 -97 Unit Test Test Condition Fig. No. Parameter 80. Psophometric NP, VIT noise Frequency response VIT/V2W (guaranteed by design) 81. Amplitude 82. Phase Longitudinal LITRR to transversal current output rejection ratio Vlong/VIT 83. 84. Power supply PSRR rejection ratio 85. VBAT/VIT 86. VH/VIT 87. VDD/VIT 88. VSS/VIT - CONV - CONV - dBmp 4 4 Iab = 30 mA, T>00C -400C - 0.5 100 CONV 1.7 - 1.95 - dB deg 6 Vlong = 3 Vrms Iab = 30 mA 75 81 - - - - dB dB 4 300 Hz < f < 3.4 kHz f = 1015 Hz 300 Hz < f < 3.4 kHz Vsupply,AC = 100 mVp Iab = 30 mA CONV, 50 PD BB 50 CONV 50 CONV 50 60 60 60 60 - - - - dB dB dB dB Semiconductor Group 20 1998-03-01 PEB/F 4065 Electrical Characteristics Table 9 External Elements in the Application Circuit (Figure 5) Typical values are used in the test circuits, unless otherwise specified. Typ. Value Tolerance 25 k - - Limit Values min. max. 50 k power dissipation increases with smaller R1 clipping for IT x R 2 > 3 V or IL x R3 > 3 V - Comment Ext. Part Function R1 Biasing, current reference R2 , R3 IT, IL gain adjustment 1 k 0.1% (rel.) - - RS Protection, isolation of capacitive load Protection C for the internal supply voltage filter 50 0.1% (rel.) 30 - R5 , R6 C1 50 0.1% (rel.) - 10 nF - - - 20% 22 F (f3dB 3 Hz) f3dB increases with smaller C1, causing worse low frequency PSRR from VBAT CS Suppression 15 nF of voltage spikes, frequency compensation 5% (rel.) 200 pF 20 nF - C2, C3 VDD, VSS supply voltage blocking 1 F 20% 10 nF - C4 C5 VH blocking 100 nF - - - C2, C3 > 1 F and C4 C5 allows arbitrary switching sequence of all supply voltages incl. ground VBAT blocking 100 nF 20% 100 nF - Note: Exceeding the min./max. limits can cause stability problems! Semiconductor Group 21 1998-03-01 PEB/F 4065 Electrical Characteristics 5 V -5 V 60 V -70 V PEB 3065 SLICOFI 5V 14 C1 15 C2 7 19 VDD VSS 5 VH C2 1 F C3 1 F C4 100 nF C5 100 nF 1, 10, 11, 20 VBAT TIP 3 1) Subscriber Line RS 30 R5 CS 15 nF CS 15 nF 51 b R1 24.9 k 8V 2W 12 PDN PEB 4065 RING 2 30 BGND AGND VBIM 6 13 16 9 2) C1 22 F/10 V 1) RS R6 51 a T T 17 18 R IT 1 k 1) 2) R IL 1 k Careful symmetrical board layout with respect to a and b Connect close to pin 16 Figure 5 Application Circuit Semiconductor Group 22 + ITS10506 1998-03-01 PEB/F 4065 Electrical Characteristics V DD PDN VBIM VSS C BIM V DD V BAT VH SS DD BAT H R PDN VREF VBIM PDN VSS V DD V BAT VH TIP RING PEB 4065 BGND V2W C1 C2 L R IL T AGND R IT See Testcond. ITS10507 Test Figure 1 DC Characteristics and Power Dissipation Semiconductor Group 23 1998-03-01 PEB/F 4065 Electrical Characteristics VSS C BIM VBIM 25 k PDN V DD V BAT VH VSS V DD V BAT VH RING Vab TIP a b PEB 4065 BGND V2W C1 C2 L L AGND T T ITS10508 See Testcond. Test Figure 2 DC Line Voltage and Currents Semiconductor Group 24 1998-03-01 PEB/F 4065 Electrical Characteristics VSS C BIM VBIM 25 k PDN V DD V BAT VH VSS V DD V BAT VH RING TIP a, max b, max Va Vb PEB 4065 BGND V2W C1 C2 L R IL AGND T R IT Va , Vb : BGND / VBAT in PDN, CONV BGND in BB, RING ITS10509 See Testcond. Test Figure 3 Output Current Limit DC and AC VSS C BIM VBIM 25 k PDN V DD V BAT VH VSS V DD V BAT VH TIP RS RS RL Vab, AC RING V2W, AC V2W, DC V2W C1 PEB 4065 BGND AGND C2 L R IL T R IT VIT, AC ITS10510 Gr = Vab, AC V2W, AC Vab, AC 1000 VIT, AC 660 See Testcond. G IT = Test Figure 4 Receive Gain, Transversal Current Ratio, THD, Noise and Power Supply Rejection 25 1998-03-01 Semiconductor Group PEB/F 4065 Electrical Characteristics VSS C BIM VBIM 25 k PDN V DD V BAT VH VSS V DD V BAT VH TIP 2 F RING RS RS RL Vab, AC V2W, AC V2W, DC V2W C1 PEB 4065 BGND AGND T C2 L R IL R IT ITS10511 See Testcond. Test Figure 5 Teletax Distortion VSS C BIM VBIM VSS V DD V BAT VH TIP PDN RING V DD V BAT VH RS RS R L/2 VLong R L/2 25 k ~ ~ Vab, AC PEB 4065 V2W, DC V2W C1 C2 BGND AGND T L R IL R IT V IT ITS10512 See Testcond. Test Figure 6 Longitudinal to Transversal Rejection Ratio Semiconductor Group 26 1998-03-01 PEB/F 4065 Electrical Characteristics VSS C BIM VBIM 25 k PDN V DD V BAT VH VSS V DD V BAT VH TIP RS RS R L/2 R L/2 VLong, AC Vab, AC RING V2W, AC V2W, DC V2W C1 PEB 4065 BGND AGND T C2 L R IL R IT ITS10513 See Testcond. Test Figure 7 Transversal to Longitudinal Rejection Ratio VSS C BIM VBIM 25 k PDN RING V DD V BAT VH VSS V DD V BAT VH RS TIP CL RS RL VRING PEB 4065 V2W V2W C1 C2 BGND L R IL AGND T R IT ITS10514 See Testcond. Test Figure 8 Ringing Semiconductor Group 27 1998-03-01 PEB/F 4065 Electrical Characteristics V DD PDN VSS C BIM VBIM PDN V DD V BAT VH SS VSS DD V DD BAT V BAT H VH TIP RING R PDN b a V TIP V BAT PEB 4065 BGND VRING VBAT V2W C1 C2 L R IL AGND T R IT ITS10515 See Testcond. Test Figure 9 Output Resistance in PDNR Mode V DD PDN VBIM VSS C BIM V DD V BAT VH SS VSS DD V DD BAT V BAT H VH TIP 30 30 RING R PDN VREF VBIM PDN VH +10 V / 1 ms VH +20 V / 1 s VBAT -10 V / 1 ms VBAT -20 V / 1 s PEB 4065 BGND V2W C1 C2 L R IL AGND T R IT ITS10516 Test Figure 10 TIP, RING Overvoltage Pulses Semiconductor Group 28 1998-03-01 PEB/F 4065 Package Outlines 3 Package Outlines P-DSO-20-5 (Plastic Dual Small Outline Package) Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book "Package Information". SMD = Surface Mounted Device Semiconductor Group 29 Dimensions in mm 1998-03-01 GPS05755 |
Price & Availability of PEB4065
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |