View LD1086XX90_223773.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LD1086 SERIES
1.5A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED
s s
s
s
s s
s
s
TYPICAL DROPOUT 1.3V AT 1.5A THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 3.6V, 5V, 8V, 9V, 12V. GUARANTEED OUTPUT CURRENT UP TO 1.5A OUPUT TOLERANCE 1% AT 25C AND 2% IN FULL TEMPERATURE RANGE INTERNAL POWER AND THERMAL LIMIT WIDE OPERATING TEMPERATURE RANGE -40C TO 125C PACKAGE AVAILABLE : TO-220, D2PAK, D2PAK/A, DPAK PINOUT COMPATIBILITY WITH STANDARD ADJUSTABLE VREG
TO-220
DPAK
D2PAK
D2PAK/A
DESCRIPTION The LD1086 is a LOW DROP Voltage Regulator able to provide up to 1.5A of Output Current. Dropout is guaranteed at a maximum of 1.5V at the maximum output current, decreasing at lower loads. The LD1086 is pin to pin compatible with the older 3-terminal adjustable regulators, but has better performances in term of drop and output tolerance .
A 2.85V output version is suitable for SCSI-2 active termination. Unlike PNP regulators, where a part of the output current is wasted as quiescent current, the LD1086 quiescent current flows into the load, so increase efficiency. Only a 10F minimum capacitor is need for stability. The device is supplied in TO-220, D2PAK, D2PAK/A and DPAK. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within 1% at 25C.
SCHEMATIC DIAGRAM
October 2002
1/19
LD1086 SERIES
ABSOLUTE MAXIMUM RATINGS
Symbol VI IO PD Tstg Top DC Input Voltage Output Current Power Dissipation Storage Temperature Range Operating Junction Temperature Range Parameter Value 30 Internally Limited Internally Limited -55 to +150 -40 to +125 Unit V mA mW C C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied.
THERMAL DATA
Symbol Rthj-case Rthj-amb Parameter Thermal Resistance Junction-case Thermal Resistance Junction-ambient TO-220 3 50 D2PAK 3 62.5 DPAK 8 Unit C/W C/W
APPLICATION CIRCUITS
R2 VO = VREF (1 + ) R1
2/19
LD1086 SERIES
CONNECTION DIAGRAM (top view)
TO-220
D2PAK
DPAK
D2PAK/A
ORDERING CODES
TO-220 LD1086V15 LD1086V18 LD1086V25 LD1086V28 LD1086V33 LD1086V36 LD1086V50 LD1086V80 LD1086V90 LD1086V12 LD1086V D2PAK (*) LD1086D2T15 LD1086D2T18 LD1086D2T25 LD1086D2T28 LD1086D2T33 LD1086D2T36 LD1086D2T50 LD1086D2T80 LD1086D2T90 LD1086D2T12 LD1086D2T D2PAK/A (*) LD1086D2M15 LD1086D2M18 LD1086D2M25 LD1086D2M28 LD1086D2M33 LD1086D2M36 LD1086D2M50 LD1086D2M80 LD1086D2M90 LD1086D2M12 LD1086D2M DPAK (*) LD1086DT15 LD1086DT18 LD1086DT25 LD1086DT28 LD1086DT33 LD1086DT36 LD1086DT50 LD1086DT80 LD1086DT90 LD1086DT12 LD1086DT OUTPUT VOLTAGE 1.5 V 1.8 V 2.5 V 2.85 V 3.3 V 3.6 V 5.0 V 8.0 V 9.0 V 12.0 V ADJ
(*) Available in Tape & Reel with the suffix "R" for fixed version and "-R" for adjustable version.
3/19
LD1086 SERIES
ELECTRICAL CHARACTERISTICS OF LD1086#15 (VI=4.5V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 6.5 3V TA = 25C f =10Hz to 10KHz 60 1.5 0.05 Test Conditions TJ = 25C VI = 3.4 to 30V VI = 3.1 to 18V VI = 3.1 to 15V TJ = 25C TJ = 25C Min. 1.485 1.47 Typ. 1.5 1.5 0.2 0.4 0.5 1 1.3 5 2 0.02 0.01 82 0.003 0.5 0.5 0.04 Max. 1.515 1.53 4 4 8 16 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1086#18 (VI=4.8V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 6.8 3V TA = 25C f =10Hz to 10KHz 60 1.5 0.05 Test Conditions TJ = 25C VI = 3.4 to 30V VI = 3.4 to 18V VI = 3.4 to 15V TJ = 25C TJ = 25C Min. 1.782 1.764 Typ. 1.8 1.8 0.2 0.4 0.5 1 1.3 5 2 0.02 0.01 82 0.003 0.5 0.5 0.04 Max. 1.818 1.836 4 4 8 16 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
4/19
LD1086 SERIES
ELECTRICAL CHARACTERISTICS OF LD1086#25 (VI=5.5V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 7.5 3V TA = 25C f =10Hz to 10KHz 60 1.5 0.05 Test Conditions TJ = 25C VI = 4.1 to 30V VI = 4.1 to 18V VI = 4.1 to 18V TJ = 25C TJ = 25C Min. 2.475 2.45 Typ. 2.5 2.5 0.2 0.4 0.5 1 1.3 5 2 0.2 0.008 81 0.003 0.5 0.5 0.04 Max. 2.525 2.55 4 4 8 16 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1086#285 (VI=5.85V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 7.85 3V TA = 25C f =10Hz to 10KHz 60 1.5 0.05 Test Conditions TJ = 25C VI = 4.5 to 30V VI = 4.5 to 18V VI = 4.5 to 18V TJ = 25C TJ = 25C Min. 2.821 2.793 Typ. 2.85 2.85 0.2 0.5 1 2 1.3 5 2 0.2 0.01 80 0.003 0.5 0.5 0.04 Max. 2.879 2.907 6 6 12 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
5/19
LD1086 SERIES
ELECTRICAL CHARACTERISTICS OF LD1086#33 (VI=6.3V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 8.3 3V TA = 25C f =10Hz to 10KHz 60 1.5 0.05 Test Conditions TJ = 25C VI = 4.9 to 30V TJ = 25C VI = 4.9 to 18V VI = 4.9 to 18V TJ = 25C IO = 0 to 1.5A` Min. 3.267 3.234 Typ. 3.3 3.35 0.5 1 1 7 1.3 5 2 0.2 0.008 79 0.003 0.5 0.5 0.04 Max. 3.333 3.366 6 6 10 25 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1086#36 (VI=6.6V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 8.6 3V TA = 25C f =10Hz to 10KHz 60 1.5 0.05 Test Conditions TJ = 25C VI = 5.2 to 30V VI = 5.2 to 18V VI = 5.2 to 18V TJ = 25C TJ = 25C Min. 3.564 3.528 Typ. 3.6 3.6 0.5 1 3 7 1.3 5 2 0.2 0.01 78 0.003 0.5 0.5 0.04 Max. 3.636 3.672 10 10 15 25 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
6/19
LD1086 SERIES
ELECTRICAL CHARACTERISTICS OF LD1086#50 (VI=8V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 10 3V TA = 25C f =10Hz to 10KHz 60 1.5 0.05 Test Conditions TJ = 25C VI = 6.6 to 30V VI = 6.6 to 20V VI = 6.6 to 20V TJ = 25C TJ = 25C Min. 4.95 4.9 Typ. 5 5 0.5 1 5 10 1.3 5 2 0.2 0.01 75 0.003 0.5 0.5 0.04 Max. 5.05 5.1 10 10 20 35 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1086#80 (VI=11V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO =1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 13 3V TA = 25C f =10Hz to 10KHz 54 1.5 0.04 Test Conditions TJ = 25C VI = 9.8 to 30V VI = 9.8 to 20V VI = 9.8 to 20V TJ = 25C TJ = 25C Min. 7.92 7.84 Typ. 8 8 1 2 8 12 1.3 5 2 0.2 0.01 71 0.003 0.5 0.5 0.04 Max. 8.08 8.16 18 18 30 60 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
7/19
LD1086 SERIES
ELECTRICAL CHARACTERISTICS OF LD1086#90 (VI=12V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 14 3V TA = 25C f =10Hz to 10KHz 54 1.5 0.05 Test Conditions TJ = 25C VI = 11 to 30V VI = 11 to 20V VI = 11 to 20V TJ = 25C TJ = 25C Min. 8.91 8.82 Typ. 9 9 1 2 8 12 1.3 5 2 0.2 0.01 70 0.003 0.5 0.5 0.04 Max. 9.09 9.18 20 20 30 60 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1086#120 (VI=15V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 to 1.5A IO = 0 mA IO = 0 mA IO = 0 to 1.5A IO = 0 to 1.5A IO = 1.5A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 1.5A VI = 17 3V TA = 25C f =10Hz to 10KHz 54 1.5 0.05 Test Conditions TJ = 25C VI = 13.8 to 30V VI = 13.8 to 25V VI = 13.8 to 25V TJ = 25C TJ = 25C Min. 11.88 11.76 Typ. 12 12 1 2 12 24 1.3 5 2 0.2 0.01 66 0.003 0.5 0.5 0.04 Max. 12.12 12.24 25 25 36 72 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
8/19
LD1086 SERIES
ELECTRICAL CHARACTERISTICS OF LD1086# (VI=4.25V, C I = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd IO(min) Isc Parameter Output Voltage (note 1) Line Regulation Load Regulation Dropout Voltage Minimum Load Current Short Circuit Current Termal Regulation SVR IADJ IADJ eN S S Supply Voltage Rejection Adjust Pin Current Adjust Pin Current Change RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 10mA IO = 10mA IO = 10mA IO = 0 to 1.5A IO = 1.5A VI = 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, IO = 1.5A VI = 4.25V CO = 25 F, CADJ = 25 F, VI = 6.25 3V IO = 10 mA 60 1.5 0.05 Test Conditions TJ = 25C VI = 2.8 to 16.5V TJ = 25C VI = 2.8 to 16.5V IO = 10mA to 1.5A VI = 2.85 to 30V Min. 1.237 1.225 Typ. 1.25 1.25 0.015 0.035 0.1 0.2 1.3 3 2.3 0.2 0.01 88 40 0.2 0.003 0.5 0.5 120 5 0.04 Max. 1.263 1.275 0.2 0.2 0.3 0.4 1.5 10 Unit V V % % % % V mA A A %/W dB A A % % %
IO = 10mA to 1.5A TJ = 25C
IO = 10mA to 1.5A VI = 2.8 to 16.5V (note 1) TA = 25C f =10Hz to 10KHz
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
9/19
LD1086 SERIES
TYPICAL CHARACTERISTICS (unless otherwise specified Tj = 25C, CI=CO=10F) Figure 1 : Output Voltage vs Temperature Figure 4 : Short Circuit Current vs Dropout Voltage
Figure 2 : Output Voltage vs Temperature
Figure 5 : Line Regulation vs Temperature
Figure 3 : Output Voltage vs Temperature
Figure 6 : Load Regulation vs Temperature
10/19
LD1086 SERIES
Figure 7 : Dropout Voltage vs Temperature Figure 10 : Adjust Pin Current vs Temperature
Figure 8 : Dropout Voltage vs Output Current
Figure 11 : Adjust Pin Current vs Output Current
Figure 9 : Adjust Pin Current vs Input Voltage
Figure 12 : Quiescent Current vs Output Current
11/19
LD1086 SERIES
Figure 13 : Quiescent Current vs Input Voltage Figure 16 : Supply Voltage Rejection vs Temperature
Figure 14 : Supply Voltage Rejection vs Output Current
Figure 17 : Minimum Load Current vs Temperature
Figure 15 : Supply Voltage Rejection vs Frequency
Figure 18 : Stability for Adjustable
12/19
LD1086 SERIES
Figure 19 : Stability for 2.85V Figure 22 : Line Transient
VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), No CADJ
Figure 20 : Stability for 12V
Figure 23 : Line Transient
VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), CADJ =1F
Figure 21 : Line Transient
Figure 24 : Load Transient
VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), No CADJ
VI=13V, IO=0.1 to 1.5A, CI = 1F(tant), CO=10F(tant) CADJ =1F
13/19
LD1086 SERIES
Figure 25 : Load Transient Figure 26 : Thermal Protection
VI=13V, IO=0.1 to 1.5A, CI = 1F(tant), CO=10F(tant) CADJ =1F
VO=2.85 V
14/19
LD1086 SERIES
TO-220 MECHANICAL DATA
DIM. A C D D1 E F F1 F2 G G1 H2 L2 L4 L5 L6 L7 L9 DIA. 13.0 2.65 15.25 6.2 3.5 3.75 0.49 0.61 1.14 1.14 4.95 2.4 10.0 16.4 14.0 2.95 15.75 6.6 3.93 3.85 0.511 0.104 0.600 0.244 0.137 0.147 mm. MIN. 4.40 1.23 2.40 1.27 0.70 0.88 1.70 1.70 5.15 2.7 10.40 0.019 0.024 0.044 0.044 0.194 0.094 0.393 0.645 0.551 0.116 0.620 0.260 0.154 0.151 TYP MAX. 4.60 1.32 2.72 MIN. 0.173 0.048 0.094 0.050 0.027 0.034 0.067 0.067 0.203 0.106 0.409 inch TYP. MAX. 0.181 0.051 0.107
P011C
15/19
LD1086 SERIES
D2PAK MECHANICAL DATA
mm. DIM. MIN. A A1 A2 B B2 C C2 D D1 E E1 G L L2 L3 M R V2 0 4.88 15 1.27 1.4 2.4 0.4 8 0 10 8.5 5.28 15.85 1.4 1.75 3.2 0.192 0.590 0.050 0.055 0.094 0.016 8 4.4 2.49 0.03 0.7 1.14 0.45 1.23 8.95 8 10.4 0.393 0.335 0.208 0.624 0.055 0.068 0.126 TYP MAX. 4.6 2.69 0.23 0.93 1.7 0.6 1.36 9.35 MIN. 0.173 0.098 0.001 0.027 0.044 0.017 0.048 0.352 0.315 0.409 TYP. MAX. 0.181 0.106 0.009 0.036 0.067 0.023 0.053 0.368 inch
P011P6G
16/19
LD1086 SERIES
D2PAK/A MECHANICAL DATA
mm. DIM. MIN. A A1 B B2 C C2 D E G L L2 4.40 2.49 0.7 1.14 0.45 1.21 8.95 10 4.88 15 1.27 TYP MAX. 4.60 2.69 0.93 1.7 0.60 1.36 9.35 10.4 5.28 15.85 1.4 MIN. 0.173 0.098 0.027 0.044 0.017 0.047 0.352 0.393 0.192 0.590 0.050 TYP. MAX. 0.181 0.106 0.036 0.067 0.023 0.053 0.368 0.409 0.208 0.106 0.055 inch
17/19
LD1086 SERIES
DPAK MECHANICAL DATA
mm. DIM. MIN. A A1 A2 B B2 C C2 D E G H L2 L4 0.6 2.2 0.9 0.03 0.64 5.2 0.45 0.48 6 6.4 4.4 9.35 0.8 1 0.023 TYP MAX. 2.4 1.1 0.23 0.9 5.4 0.6 0.6 6.2 6.6 4.6 10.1 MIN. 0.086 0.035 0.001 0.025 0.204 0.017 0.019 0.236 0.252 0.173 0.368 0.031 0.039 TYP. MAX. 0.094 0.043 0.009 0.035 0.212 0.023 0.023 0.244 0.260 0.181 0.397 inch
0068772-B
18/19
LD1086 SERIES
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. (c) http://www.st.com
19/19

▲Up To Search▲

Price & Availability of LD1086XX90

	To Download LD1086XX90 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .