View IRF7823PBF_241458.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PD - 97050
IRF7823PBF
HEXFET(R) Power MOSFET
Applications l High Frequency Point-of-Load Synchronous Buck Converter for Applications in Networking & Computing Systems l Optimized for Control FET applications Benefits l Very Low RDS(on) at 4.5V VGS l Low Gate Charge l Fully Characterized Avalanche Voltage and Current l 100% Tested for RG
VDSS
30V
RDS(on) max
Qg
8.7m:@VGS = 10V 9.1nC
A A D D D D
S S S G
1 2 3 4
8 7
6 5
Top View
SO-8
Absolute Maximum Ratings
Parameter
VDS VGS ID @ TA = 25C ID @ TA = 70C IDM PD @TA = 25C PD @TA = 70C TJ TSTG Drain-to-Source Voltage Gate-to-Source Voltage Continuous Drain Current, VGS @ 10V Continuous Drain Current, VGS @ 10V Pulsed Drain Current Power Dissipation Power Dissipation
Max.
30 20 13 11 100 2.5 1.6 0.02 -55 to + 150
Units
V
f f
c
A W W/C C
Linear Derating Factor Operating Junction and Storage Temperature Range
Thermal Resistance
RJL RJA
g Junction-to-Ambient fg
Junction-to-Drain Lead
Parameter
Typ.
--- ---
Max.
20 50
Units
C/W
Notes through are on page 10
www.irf.com
1
10/06/05
IRF7823PBF
Static @ TJ = 25C (unless otherwise specified)
Parameter
BVDSS VDSS/TJ RDS(on) VGS(th) VGS(th) IDSS IGSS gfs Qg Qgs1 Qgs2 Qgd Qgodr Qsw Qoss Rg td(on) tr td(off) tf Ciss Coss Crss Drain-to-Source Breakdown Voltage Breakdown Voltage Temp. Coefficient Static Drain-to-Source On-Resistance Gate Threshold Voltage Gate Threshold Voltage Coefficient Drain-to-Source Leakage Current Gate-to-Source Forward Leakage Gate-to-Source Reverse Leakage Forward Transconductance Total Gate Charge Pre-Vth Gate-to-Source Charge Post-Vth Gate-to-Source Charge Gate-to-Drain Charge Gate Charge Overdrive Switch Charge (Qgs2 + Qgd) Output Charge Gate Resistance Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Input Capacitance Output Capacitance Reverse Transfer Capacitance Parameter Single Pulse Avalanche Energy Avalanche Current
Min. Typ. Max. Units
30 --- --- --- 1.35 --- --- --- --- --- 27 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- 0.024 6.9 9.3 1.8 -5.1 --- --- --- --- --- 9.1 2.7 0.84 3.2 2.4 4.0 5.8 2.0 7.2 8.2 10 2.7 1110 240 110 --- --- 8.7 11.9 2.35 --- 1.0 150 100 -100 --- 14 --- --- --- --- --- --- 3.0 --- --- --- --- --- --- --- Typ. --- --- pF ns nC nC VDS = 15V VGS = 4.5V ID = 10A S nA V mV/C A V m
Conditions
VGS = 0V, ID = 250A VGS = 10V, ID = 13A VGS = 4.5V, ID = 10A
V/C Reference to 25C, ID = 1mA
VDS = VGS, ID = 25A VDS = 24V, VGS = 0V
e e
VDS = 24V, VGS = 0V, TJ = 125C VGS = 20V VGS = -20V VDS = 15V, ID = 10A
See Fig. 17 & 18 VDS = 16V, VGS = 0V VDD = 16V, VGS = 4.5V ID = 10A Clamped Inductive Load See Fig. 15 VGS = 0V VDS = 15V = 1.0MHz Max. 230 10 Units mJ A
Avalanche Characteristics
EAS IAR
d
Diode Characteristics
Parameter
IS ISM VSD trr Qrr ton Continuous Source Current (Body Diode) Pulsed Source Current (Body Diode)A Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Forward Turn-On Time
Min. Typ. Max. Units
--- --- --- --- --- --- --- --- 7.8 9.0 3.1 A 100 1.0 12 14 V ns nC
Conditions
MOSFET symbol showing the integral reverse
G S D
p-n junction diode. TJ = 25C, IS = 10A, VGS = 0V
TJ = 25C, IF = 10A, VDD = 15V Fig. 16 di/dt = 500A/s
e
eASee
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
2
www.irf.com
IRF7823PBF
1000
TOP VGS 10V 5.0V 4.5V 3.5V 3.0V 2.7V 2.5V 2.3V
1000
TOP VGS 10V 5.0V 4.5V 3.5V 3.0V 2.7V 2.5V 2.3V
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
100
BOTTOM
100
BOTTOM
10
10
1
1
2.3V
0.1 2.3V 0.01 0.1 1
60s PULSE WIDTH
Tj = 25C 0.1 100 0.1 1 10
60s PULSE WIDTH
Tj = 150C 10 100
V DS, Drain-to-Source Voltage (V)
V DS, Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
Fig 2. Typical Output Characteristics
1000
2.0
RDS(on) , Drain-to-Source On Resistance (Normalized)
ID, Drain-to-Source Current (A)
ID = 13A VGS = 10V
100
1.5
10 T J = 150C 1 VDS = 15V 60s PULSE WIDTH 0.1 1 2 3 4 5 T J = 25C
1.0
0.5 -60 -40 -20 0 20 40 60 80 100 120 140 160
VGS, Gate-to-Source Voltage (V)
T J , Junction Temperature (C)
Fig 3. Typical Transfer Characteristics
Fig 4. Normalized On-Resistance vs. Temperature
www.irf.com
3
IRF7823PBF
10000
VGS = 0V, f = 1 MHZ Ciss = C gs + Cgd, C ds SHORTED
12.0 ID= 10A
VGS, Gate-to-Source Voltage (V)
Crss = C gd Coss = Cds + Cgd
10.0 8.0 6.0 4.0 2.0 0.0
C, Capacitance (pF)
1000
Ciss
VDS= 24V VDS= 15V
Coss 100 Crss
10 1 10 VDS, Drain-to-Source Voltage (V) 100
0
2
4
6
8
10 12 14 16 18 20
QG, Total Gate Charge (nC)
Fig 5. Typical Capacitance vs. Drain-to-Source Voltage
Fig 6. Typical Gate Charge vs. Gate-to-Source Voltage
1000
1000
OPERATION IN THIS AREA LIMITED BY R DS(on)
ISD, Reverse Drain Current (A)
ID, Drain-to-Source Current (A)
100 T J = 150C 10 T J = 25C
100
100sec
10
1msec
1
10msec
1 VGS = 0V 0.1 0.2 0.4 0.6 0.8 1.0 1.2 VSD, Source-to-Drain Voltage (V)
0.1
T A = 25C Tj = 150C Single Pulse 0 1 10 100
0.01 VDS, Drain-to-Source Voltage (V)
Fig 7. Typical Source-Drain Diode Forward Voltage
Fig 8. Maximum Safe Operating Area
4
www.irf.com
IRF7823PBF
14 12
ID, Drain Current (A) VGS(th) , Gate Threshold Voltage (V)
2.5
10 8 6 4 2 0 25 50 75 100 125 150 T A , Ambient Temperature (C)
2.0
1.5
ID = 50A
1.0
0.5 -75 -50 -25 0 25 50 75 100 125 150 T J , Temperature ( C )
Fig 9. Maximum Drain Current vs. Case Temperature
Fig 10. Threshold Voltage vs. Temperature
100 10
Thermal Response ( Z thJA )
1 0.1 0.01 0.001
D = 0.50 0.20 0.10 0.05 0.02 0.01
J J 1 1
R1 R1 2
R2 R2
R3 R3 A 3 A
2
3
C i= i/R i C i= i/R i
Ri (C/W) i (sec) 7.520 0.013427 25.573 1.1097 16.913 36.9
SINGLE PULSE ( THERMAL RESPONSE )
Notes: 1. Duty Factor D = t1/t2 2. Peak Tj = P dm x Zthja + Ta
0.0001 1E-006
1E-005
0.0001
0.001
0.01
0.1
1
10
100
1000
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Ambient
www.irf.com
5
IRF7823PBF
RDS(on), Drain-to -Source On Resistance (m )
30 ID = 13A 25 20 15 10 5 0 2 4 6 8 10 T J = 25C
1000
EAS , Single Pulse Avalanche Energy (mJ)
800
ID TOP 0.82A 1.1A BOTTOM 10A
600
T J = 125C
400
200
0 25 50 75 100 125 150 Starting T J , Junction Temperature (C)
VGS, Gate -to -Source Voltage (V)
Fig 12. On-Resistance vs. Gate Voltage
Fig 13. Maximum Avalanche Energy vs. Drain Current
LD
15V
VDS
VDS
L
DRIVER
VDD D.U.T
RG
VGS 20V
D.U.T
IAS tp
+ V - DD
VGS
A
0.01
Pulse Width < 1s Duty Factor < 0.1%
Fig 14a. Unclamped Inductive Test Circuit
V(BR)DSS tp
Fig 15a. Switching Time Test Circuit
90%
VDS
10%
VGS
I AS
td(on)
tf
td(off)
tr
Fig 14b. Unclamped Inductive Waveforms
Fig 15b. Switching Time Waveforms
6
www.irf.com
IRF7823PBF
D.U.T
Driver Gate Drive
+
P.W.
Period
D=
P.W. Period VGS=10V
+
Circuit Layout Considerations * Low Stray Inductance * Ground Plane * Low Leakage Inductance Current Transformer
*
D.U.T. ISD Waveform Reverse Recovery Current Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt
-
-
+
RG
* * * * dv/dt controlled by RG Driver same type as D.U.T. ISD controlled by Duty Factor "D" D.U.T. - Device Under Test
VDD
VDD
+ -
Re-Applied Voltage Inductor Curent
Body Diode
Forward Drop
Ripple 5%
ISD
* VGS = 5V for Logic Level Devices Fig 16. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET(R) Power MOSFETs
Current Regulator Same Type as D.U.T.
Id Vds Vgs
50K 12V .2F .3F
D.U.T. VGS
3mA
+ V - DS
Vgs(th)
IG
ID
Qgs1 Qgs2
Qgd
Qgodr
Current Sampling Resistors
Fig 17. Gate Charge Test Circuit
Fig 18. Gate Charge Waveform
www.irf.com
7
IRF7823PBF
Power MOSFET Selection for Non-Isolated DC/DC Converters
Control FET Special attention has been given to the power losses in the switching elements of the circuit - Q1 and Q2. Power losses in the high side switch Q1, also called the Control FET, are impacted by the Rds(on) of the MOSFET, but these conduction losses are only about one half of the total losses. Power losses in the control switch Q1 are given by; Synchronous FET The power loss equation for Q2 is approximated by;
* P =P loss conduction + P drive + P output
P = Irms x Rds(on) loss
+ (Qg x Vg x f )
(
2
)
Ploss = Pconduction+ Pswitching+ Pdrive+ Poutput
This can be expanded and approximated by;
Q + oss x Vin x f + (Qrr x Vin x f ) 2
*dissipated primarily in Q1. For the synchronous MOSFET Q2, Rds(on) is an important characteristic; however, once again the importance of gate charge must not be overlooked since it impacts three critical areas. Under light load the MOSFET must still be turned on and off by the control IC so the gate drive losses become much more significant. Secondly, the output charge Qoss and reverse recovery charge Qrr both generate losses that are transfered to Q1 and increase the dissipation in that device. Thirdly, gate charge will impact the MOSFETs' susceptibility to Cdv/dt turn on. The drain of Q2 is connected to the switching node of the converter and therefore sees transitions between ground and Vin. As Q1 turns on and off there is a rate of change of drain voltage dV/dt which is capacitively coupled to the gate of Q2 and can induce a voltage spike on the gate that is sufficient to turn the MOSFET on, resulting in shoot-through current . The ratio of Qgd/Qgs1 must be minimized to reduce the potential for Cdv/dt turn on.
Ploss = (Irms x Rds(on ) )
2
Qgs 2 Qgd +I x x Vin x f + I x x Vin x f ig ig + (Qg x Vg x f ) + Qoss x Vin x f 2
This simplified loss equation includes the terms Qgs2 and Qoss which are new to Power MOSFET data sheets. Qgs2 is a sub element of traditional gate-source charge that is included in all MOSFET data sheets. The importance of splitting this gate-source charge into two sub elements, Qgs1 and Qgs2, can be seen from Fig 16. Qgs2 indicates the charge that must be supplied by the gate driver between the time that the threshold voltage has been reached and the time the drain current rises to Idmax at which time the drain voltage begins to change. Minimizing Qgs2 is a critical factor in reducing switching losses in Q1. Qoss is the charge that must be supplied to the output capacitance of the MOSFET during every switching cycle. Figure A shows how Qoss is formed by the parallel combination of the voltage dependant (nonlinear) capacitances Cds and Cdg when multiplied by the power supply input buss voltage.
8
Figure A: Qoss Characteristic
www.irf.com
IRF7823PBF
SO-8 Package Outline (Dimensions are shown in millimeters (inches)
9 6 ' & % $ 7
9DH 6 6 i p 9 @ r r C F G DI8C@T HDI H6Y $"! %'' # (' ! " &$ (' (%' '( #(& $&# $AA76TD8 !$AA76TD8 !!'# !## (( (% $ % A' A HDGGDH@U@ST HDI H6Y &$ "$ !$ $ "" ( !$ $ #' # "' !&AA76TD8 %"$AA76TD8 %! $' $ !$ !& # A A'
% @
$
C !$Ab dA 6
!
"
#
%Y
r
r
6
FAA#$ 8 Ab#dA 'YAG & 'YAp
'YAi !$Ab dA
6 867
IPU@T) AA9DH@ITDPIDIBAEAUPG@S6I8DIBAQ@SA6TH@A #$H ((# !AA8PIUSPGGDIBA9DH@ITDPI)AHDGGDH@U@S "AA9DH@ITDPITA6S@ATCPXIADIAHDGGDH@U@STAbDI8C@Td #AAPVUGDI@A8PIAPSHTAUPAE@9@8APVUGDI@AHT !66 $AAA9DH@ITDPIA9P@TAIPUADI8GV9@AHPG9AQSPUSVTDPIT AAAAAHPG9AQSPUSVTDPITAIPUAUPA@Y8@@9A $Ab%d %AAA9DH@ITDPIA9P@TAIPUADI8GV9@AHPG9AQSPUSVTDPIT AAAAAHPG9AQSPUSVTDPITAIPUAUPA@Y8@@9A!$Ab d &AAA9DH@ITDPIADTAUC@AG@IBUCAPAAG@69AAPSATPG9@SDIBAUP AAAAA6ATV7TUS6U@
APPUQSDIU 'YA&!Ab!'d
%#%Ab!$$d
"YA !&Ab$d
'YA &'Ab&d
SO-8 Part Marking
(;$03/( 7+,6 ,6 $1 ,5) 026)(7 '$7( &2'( <:: 3 '(6,*1$7(6 /($')5(( 352'8&7 237,21$/ < /$67 ',*,7 2) 7+( <($5 :: :((. $ $66(0%/< 6,7( &2'( /27 &2'( 3$57 180%(5
,17(51$7,21$/ 5(&7,),(5 /2*2
;;;; )
www.irf.com
9
IRF7823PBF
SO-8 Tape and Reel
Dimensions are shown in millimeters (inches)
TERMINAL NUMBER 1
12.3 ( .484 ) 11.7 ( .461 )
8.1 ( .318 ) 7.9 ( .312 )
FEED DIRECTION
NOTES: 1. CONTROLLING DIMENSION : MILLIMETER. 2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS(INCHES). 3. OUTLINE CONFORMS TO EIA-481 & EIA-541.
330.00 (12.992) MAX.
14.40 ( .566 ) 12.40 ( .488 ) NOTES : 1. CONTROLLING DIMENSION : MILLIMETER. 2. OUTLINE CONFORMS TO EIA-481 & EIA-541.
Notes: Repetitive rating; pulse width limited by max. junction temperature. Starting TJ = 25C, L = 4.3mH, RG = 25, IAS = 10A. Pulse width 400s; duty cycle 2%. When mounted on 1 inch square copper board. R is measured at TJ approximately 90C.
Data and specifications subject to change without notice. This product has been designed and qualified for the Consumer market. Qualification Standards can be found on IR's Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information.10/05
10
www.irf.com

▲Up To Search▲

Price & Availability of IRF7823PBF

	To Download IRF7823PBF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .