View UC3879_247542.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

UC1879 UC2879 UC3879
Phase Shift Resonant Controller
FEATURES
* Programmable Output Turn On Delay; Zero Delay Available * Compatible with Voltage Mode or Current Mode Topologies * Practical Operation at Switching Frequencies to 300kHz * Four 100mA Totem Pole Outputs * 10MHz Error Amplifier * Pin Programmable Undervoltage Lockout * Low Startup Current - 150A * Soft Start Control * Outputs Active Low During UVLO
DESCRIPTION
The UC3879 controls a bridge power stage by phase shifting the switching of one half-bridge with respect to the other. This allows constant frequency pulse width modulation in combination with resonant, zero-voltage switching for high efficiency performance. The UC3879 can be configured to provide control in either voltage mode or current mode operation, with overcurrent shutdown for fast fault protection. Independently programmable time delays provide dead-time at the turn-on of each output stage, allowing time for each resonant switching interval. With the oscillator capable of operating in excess of 600kHz, overall output switching frequencies to 300kHz are practical. In addition to the standard free running mode, with the CLKSYNC pin, the user may configure the UC3879 to accept an external clock synchronization signal. Alternatively, up to three units can be locked together with the operational frequency determined by the fastest device. Protective features include an undervoltage lockout and overcurrent protection. Additional features include a 10MHz error amplifier, a 5V precision reference, and soft start. The UC3879 is available in 20 pin N, J, DW, and Q and 28 pin L packages.
BLOCK DIAGRAM
UDG-94070-1
6/98
UC1879 UC2879 UC3879 ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VC, VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . 20V Output Current, Source or Sink, DC . . . . . . . . . . . . . . . . . 20mA Analog I/0s (Pins 1, 2, 3, 4, 5, 6, 14, 15, 17, 18, 19) . . . . . . -0.3 to 5.3V (Pin 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -.03V to VIN Storage Temperature Range . . . . . . . . . . . . . -65C to +150C Junction Temperature . . . . . . . . . . . . . . . . . . . -55C to +150C Lead Temperature (Soldering, 10 sec.) . . . . . . . . . . . . +300C
Table I. Product Selection Guide
TEMPERATURE RANGE UCC1879 UCC2879 UCC3879 - 55C to +125C - 40C to +85C 0C to +70C AVAILABLE PACKAGES J, L N, DW, Q, J, L N, DW, Q
CONNECTION DIAGRAMS
Notes: Pin references are to 20 pin DIL and SOIC packages. All voltages are with respect to ground unless otherwise stated. Currents are positive into, negative out of the specified terminal. Consult Packaging Section of Databook for thermal limitations and considerations of packages.
DIL-20, SOIC-20 (Top View) J or N Package, DW Package
CLCC-28 (Top View) L Package
PLCC-20 (Top View) Q Package
2
UC1879 UC2879 UC3879 ELECTRICAL CHARACTERISTICS Unless specified; VC = VIN = VUVSEL =12V, CT = 470pF, RT = 9.53k, RDELSETA-B = RDELSEC-D = 4.8k, CDELSETA-B = CDELSETC-D = 0.01F, TA = TJ.
PARAMETER Undervoltage Lockout Start Threshold UVLO Hysteresis Input Bias, UVSEL Pin Supply Current IVIN Startup IVC Startup IVIN Operating IVC Operating Voltage Reference Output Voltage Line Regulation Load Regulation Total Variation Short Circuit Current Error Amplifier Error Amplifier Input Voltage Input Bias Current AVOL PSRR Output Sink Current Output Source Current Output Voltage High Output Voltage Low Slew Rate PWM Comparator RAMP Offset Voltage PWM Phase Shift, TDELSETA-B, TDELSETC-D = 0, Note 1 Output Skew, TDELSETA-B, TDELSETC-D = 0, Note 1 Ramp to Output Delay, TDELSETA-B = 0, TDELSETC-D = 0 Oscillator Initial Accuracy Voltage Stability Total Variation CLKSYNC Threshold Clock Out High Clock Out Low Clock Out Pulse Width Ramp Valley Voltage TA = 25C 11V < VIN < 18V Line, Temperature 160 2.3 2.8 0.5 180 200 1 200 2.5 4 1 400 0.2 1.5 600 0.4 220 2 240 2.7 kHz % kHz V V V ns V TJ = 25C, Note 3 VCOMP > VRAMPpeak + VRAMPoffset VCOMP < Zero Phase Shift Voltage VCOMP > VRAMPpeak + VRAMPoffset VCOMP < Zero Phase Shift Voltage UC3879, UC2879 UC1879 1.1 98 0 1.25 99.7 0.3 10 10 115 115 250 300 1.4 102 2 V % % ns ns ns ns 1V < VCOMP < 4V 11V < VIN < 18V VCOMP = 1V VCOMP = 4V ICOMP = -0.5mA ICOMP = 1mA TA = +25C 4 0 6 60 85 1 2.4 2.5 0.6 90 100 2.5 -1.3 4.7 0.5 11 -0.5 5 1 2.6 3 V A dB dB mA mA V V V/s TJ = +25C 11V < VIN < 18V IVREF = -10mA Line, Load, Temperature VREF = 0V, TJ = 25C 4.875 -60 4.92 5 1 5 5.08 10 20 5.125 -15 V mV mV V mA VIN = VUVSEL = 8V, VC = 18V, IDELSETA-B = IDELSETC-D = 0 VIN = VUVSEL = 8V, VC = 18V, IDELSETA-B = IDELSETC-D = 0 UC3879, UC2879 UC1879 150 10 23 23 4 600 100 33 36 8 A A mA mA mA VUVSEL = VIN VUVSEL = Open VUVSEL = VIN VUVSEL = Open VUVSEL = VIN = 8V 9 12.5 1.15 5.2 10.75 15.25 1.75 6 30 12.5 16.5 2.15 7.4 V V V V A TEST CONDITIONS MIN TYP MAX UNITS
3
UC1879 UC2879 UC3879 ELECTRICAL CHARACTERISTICS Unless specified; VC = VIN = VUVSEL =12V, CT = 470pF, RT = 9.53k, RDELSETA-B = RDELSEC-D = 4.8k, CDELSETA-B = CDELSETC-D = 0.01F, TA = TJ.
PARAMETER Ramp Peak Voltage Current Limit Input Bias Threshold Voltage Delay to OUTA, B, C, D Cycle-by-Cycle Current Limit Input Bias Threshold Voltage Delay to Output Zero Phase Soft Start/Reset Delay Charge Current Discharge Current Restart Threshold Discharge Level Output Drivers Output Low Level Output High Level Delay Set (Note 5) Delay Time Delay Time Zero Delay RDELSETA-B = RDELSETC-D = 4.8k RDELSETA-B = RDELSETC-D= 1.9k VDELSETA-B = VDELSETC-D = 5V 300 130 430 170 5 600 250 ns ns ns IOUT = 10mA IOUT = -10mA, Referenced to VC 0.3 2.2 0.4 3 V V VSS = 0.5V VSS = 1V -20 120 4.3 -9 230 4.7 300 -3 A A V mV VCS = 2.2V 1.85 2 2 110 10 2.15 300 A V ns VCS = 3.0V 2.35 2 2.5 160 10 2.65 300 A V ns TEST CONDITIONS MIN 2.8 TYP 2.9 MAX UNITS 3.2 V
Note 1. Phase shift percentage (0% = 0, 100% = 180) is defined as =
200
where is the phase shift, and and T are defined in Figure 1. At 0% phase shift, is the output skew. Note 2. Delay time is defined as:
T
%
delay = T *
1
2
duty cycle
where T is defined in Figure 1. Note 3. Ramp offset voltage has a temperature coeffecient of about -4mV/ C. Note 4. The zero phase shift voltage is the voltage measured at COMP which forces zero phase shift. This condition corresponds to zero effective output power. Zero phase shift voltage has a temperature coeffecient of about -2mV/ C. Note 5. Delay time can be programmed via resistors from the delay set pins to ground. Duty Cycle = Period = T TDHL(A to C) = TDHL(B to D) =
t T
Delay Time = (
0. 89
* 10- * RDELAY
)
Figure 1. Phase Shift, Output Skew & Delay Time Definitions
sec
The recommended range for RDELAY is 1.9k to 10k.
4
UC1879 UC2879 UC3879 PIN DESCRIPTIONS
CLKSYNC (Bi-directional Clock and Synchronization): Used as an output, CLKSYNC provides a clock signal. As an input, this pin provides a synchronization point. Multiple UC3879s, each with their own local oscillator frequency, may be connected together by the CLKSYNC pin, and they will synchronize to the fastest oscillator. This pin may also be used to synchronize the UC3879 to an external clock, provided the frequency of the external signal is higher than the frequency of the local oscillator. CLKSYNC is internally connected to an emitter follower pull-up and a current source pull-down (300A typical). Therefore an external resistor to GND can be used to improve the CLKSYNC pin's ability to drive capacitive loads. COMP (Error Amplifier Output): This pin is the output of the gain stage for overall feedback control. Error amplifier output voltage levels below 0.9 volt forces zero phase shift. Since the error amplifier has a relatively low current drive capability, the output may be overridden by driving it with a sufficiently low impedance source. CT (Oscillator Frequency Set): After choosing RT to set the required upper end of the linear duty cycle range, the timing capacitor (CT) value is calculated to set the oscillator frequency as follows: DELSETA-B, DELSETC-D (Output Delay Control): The user programmed currents from these pins to GND set the turn on delay for the corresponding output pair. This delay is introduced between the turn off of one switch and the turn on of another in the same leg of the bridge to allow resonant switching to take place. Separate delays are provided for the two half-bridges to accommodate differences in the resonant capacitor charging currents. EA- (Error Amplifier Inverting Input): This is normally connected to the voltage divider resistors which sense the power supply output voltage level. The loop compensation components are connected between this pin and COMP. GND (Signal Ground): All voltages are measured with respect to GND. The timing capacitor on CT, and bypass capacitors on VREF and VIN should be connected directly to the ground plane near GND. OUTA - OUTD (Outputs A-D): The outputs are 100mA totem pole output drivers optimized to drive FET driver ICs. The outputs operate as pairs with a nominal 50% duty cycle. The A-B pair is intended to drive one half-bridge in the external power stage and is synchronized to the clock waveform. The C-D pair drives the other half-bridge with switching phase shifted with respect to the A-B outputs. PWRGND (Power Ground): VC should be bypassed with a ceramic capacitor from VC to the section of the ground plane that is connected to PWRGND. Any required bulk reservoir capacitor should be connected in parallel. PWRGND and GND should be connected at a single point near the chip to optimize noise rejection and minimize DC voltage drops. RAMP (Voltage Ramp): This pin is the input to the PWM comparator. Connect it to CT for voltage mode control. For current mode control, connect RAMP to CS and also to the output of the current sense transformer circuit. Slope compensation can be achieved by injecting a portion of the ramp voltage from CT to RAMP.
CT =
1. 08
Dlin * RT * f
Connect the timing capacitor directly between CT and GND. Use a high quality ceramic capacitor with low ESL and ESR for best results. A minimum CT value of 200pF insures good accuracy and less susceptibility to circuit layout parasitics. The oscillator and PWM are designed to provide practical operation to 600kHz. CS (Current Sense): This pin is the non-inverting input to the two current fault comparators whose references are set internally to fixed values of 2.0V and 2.5V. When the voltage at this pin exceeds 2.0V, and the error amplifier output voltage exceeds the voltage on the ramp input, the phase shift limiting overcurrent comparator will limit the phase shifting on a cycle-by-cycle basis. When the voltage at this pin exceeds 2.5V, the current fault latch is set, the outputs are forced OFF, and a soft start cycle is initiated. If a constant voltage above 2.5V is applied to this pin the outputs are disabled and held low. When CS is brought below 2.5V, the outputs will begin switching at 0 degrees phase shift before the SS pin begins to rise. This condition will not prematurely deliver power to the load.
5
UC1879 UC2879 UC3879 PIN DESCRIPTIONS (cont.)
RT (Clock/Sync Duty Cycle Set Pin): The UC3879 oscillator produces a sawtooth waveform. The rising edge is generated by connecting a resistor from RT to GND and a capacitor from CT to GND (see CT pin description). During the rising edge, the modulator has linear control of the duty cycle. The duty cycle jumps to 100% when the voltage on COMP exceeds the oscillator peak voltage. Selection of RT should be done first, based on the required upper end of the linear duty cycle range (Dlin) as follows: UVSEL: Connecting this pin to VIN sets a turn on voltage of 10.75V with 1.5V of UVLO hysteresis. Leaving the pin open-circuited programs a turn on voltage of 15.25V with 6.0V of hysteresis. VC (Output Switch Supply Voltage): This pin supplies power to the output drivers and their associated bias circuitry. The difference between the output high drive and VC is typically 2.1V. This supply should be bypassed directly to PWRGND with a low ESR/ESL capacitor. VIN (Primary Chip Supply Voltage): This pin supplies power to the logic and analog circuitry on the integrated circuit that is not directly associated with driving the output stages. Connect VIN to a stable source above 12V for normal operation. To ensure proper functionality, the UC3879 is inactive until VIN exceeds the upper undervoltage lockout threshold. This pin should be bypassed directly to GND with a low ESR/ESL capacitor.
NOTE: When VIN exceeds the UVLO threshold the supply current (IIN) jumps from about 100A to greater than 20mA. If the UC3879 is not connected to a well bypassed supply, it may immediately enter the UVLO state again. Therefore, sufficient bypass capacity must be added to ensure reliable startup.
RT =
10
mA * (1 Dlin)
2.5
Recommended values for RT range from 2.5k to 100k. SS: Connect a capacitor between this pin and GND to set the soft start time. The voltage at SS will remain near zero volts as long as VIN is below the UVLO threshold. Soft start will be pulled up to about 4.8V by an internal 9A current source when VIN and VREF become valid (assuming a non-fault condition). In the event of a current fault (CS voltage exceeding 2.5V), soft start will be pulled to GND and then ramp to 4.8V. If a fault occurs during the soft start cycle, the outputs will be immediately disabled and soft start must fully charge prior to resetting the fault latch. For paralleled controllers, the soft start pins may be paralleled to a single capacitor, but the charge currents will be additive.
VREF: This pin provides an accurate 5V voltage reference. It is internally short circuit current limited. VREF is disabled while VIN is below the UVLO threshold. The circuit is also disabled until VREF reaches approximately 4.75V. For best results bypass VREF with a 0.1F, low ESR/ESL capacitor.
ADDITIONAL INFORMATION
Please refer to the following Unitrode publications for additional information. The following three topics are available in the Applications Handbook. [1] Application Note U-154, The New UC3879 PhaseShifted PWM Controller Simplifies the Design of Zero Voltage Transition Full-Bridge Converters by Laszlo Balogh. [2] Application Note U-136, Phase Shifted, Zero Voltage Transition Design Considerations and the UC3875 PWM Controller by Bill Andreycak. Design Note DN-63, The Current-Doubler Rectifier: An Alternative Rectification Technique for Push-Pull and Bridge Converters by Laszlo Balogh.
UNITRODE CORPORATION 7 CONTINENTAL BLVD. * MERRIMACK, NH 03054 TEL. (603) 424-2410 FAX (603) 424-3460
6
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof.
Copyright (c) 1999, Texas Instruments Incorporated

▲Up To Search▲

Price & Availability of UC3879

	To Download UC3879 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .