 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| OSD PROCESSOR FOR MONITOR S5D2508A01 OVERVIEW The S5D2508A01 is used to display some characters or symbols on a screen of monitor. Basically, the operation is to control the internal memory on chip and generate the R,G,B signals for some characters or symbols. The R,G,B signals are synchronized with the horizontal sync. Then the R,G,B signals are mixed with the main video signal in the Video Amp IC. The font data for characters or symbols are stored in the internal ROM. This stored data are accessed and controlled by the control data from a micro controller. The control data are transmitted through the I2C bus. All timing control signals including the system clock are synchronized with the horizontal sync. Therefore there is a PLL circuitry on chip. 16-DIP-300 FEATURES * 256 ROM fonts (Each font consists of 12 x 18 dots.) * * * * * * * * * * * * * * Full Screen Memory Architecture Wide range PLL available (15 kHz -- 120 kHz) Programmable vertical height of character Programmable vertical and horizontal positioning Character color selection up to 16 different colors Programmable background color (Up to 16 colors) Character blinking, bordering and shadowing Color blinking Character scrolling Fade-in and fade-out Box drawing Character sizing up to four times 96 MHz pixel frequency from on-chip PLL ORDERING INFORMATION Device Package Operating Temperature 0C -- 70C S5D2508A01-D0B0 16-DIP-300 IIC Protocol Data Transmission (Slave Address : BAH) 1 S5D2508A01 OSD PROCESSOR FOR MONITOR BLOCK DIAGRAM SDA 7 SCL 8 Data Receiver RAM Data 16 RAM (480 x 16) ROM Addr 9 Single Color ROM (256 x 18x12) Control 16 Data Font Control Font 12 Data 15 INT Frame Control Row Control Display Controller Display Control Output Stage 14 R_OUT 13 G_OUT 12 B_OUT 11 FBLK Control Register CLK HFLB 6 VFLB 9 OSD _PLL H-Pulse V-Pulse Frame Control Row Control H/V/CLK Control H/V/CLK Control Timing Controller 2 3 5 1 4 10 16 VCO_IN VREF1 VREF Figure 1. Functional Block Diagram VSS_A VDD_A VSS_D VDD_D 2 OSD PROCESSOR FOR MONITOR S5D2508A01 PIN CONFIGURATIONS VSS-A 1 16 VDD_D VCO-IN 2 VREF1 VDD-A 3 15 INT 14 R_OUT 4 S5D2508A 13 G_OUT VREF 5 HFLB 6 SDA SCL 7 12 B_OUT 11 FBLK 10 VSS_D 8 9 VFLB Figure 2. Pin Configurations 3 S5D2508A01 OSD PROCESSOR FOR MONITOR PIN DESCRIPTIONS Table 1. Pin Descriptions Pin No. 1 2 3 Signal VSS_A VCO_IN VREF1 Active I/O Input Input Ground (Analog Part) This voltage is generated at the external loop filter and goes into the input stage of the VCO. 1.26 V DC Voltage from the Bandgap Reference. Connected to ground through a resistor to make internal reference current (Typical 36 K for 27A) +5 V Supply Voltage for Analog Part Bandgap Reference Voltage (Typical 1.26 V) Horizontal Flyback Signal Serial Data (I2C) Serial Clock (I2C) Vertical Flyback Signal Ground for Digital Part Fast Blank Signal Video Signal Output (B) Video Signal Output (G) Video Signal Output (R) Intensity Signal Output +5 V SUpply Voltage for Dogital Part Description 4 5 6 7 8 9 10 11 12 13 14 15 16 VDD_A VREF HFLB SDA SCL VFLB VSS_D FBLK B_OUT G_OUT R_OUT INT VDD_D Low Low - Input Input In/Out In/Out Input Output Output Output Output Output - 4 OSD PROCESSOR FOR MONITOR S5D2508A01 ABSOLUTE MAXIMUM RATINGS Parameters Symbol Min. Maximum Supply Voltage Input Voltage Operating Temperature Range Storage Temperature Range Power Dissipation NOTE: PKG Thermal Resistance : 64.2 C/W VDD VI TOPR TSTG PD -20 -40 Value Typ. Max. 7.0 7.0 70 125 1200 V V C C Unit mW ELECTRICAL CHARACTERISTICS DC Electrical Characteristics (Ta = 25 C, VDD = 5 V) Table 2. DC Electrical Characteristics Parameters (Conditions) Supply Voltage Supply Current (No load on any output) Input Voltage Output Voltage (lout = 1mA) Input Leakage Current VCO Input Voltage Symbol VDD IDD VIH VIL VOH VOL IIL VVCO Min. 4.75 0.8VDD 0.8VDD -10 Typ. 5.00 2.5 Max. 5.25 25 VSS + 0.4 VSS + 0.4 10 Unit V mA V V V V A V 5 S5D2508A01 OSD PROCESSOR FOR MONITOR OPERATION TIMINGS Table 3. Operation Timings Parameters (Conditions) Symbol Min. Typ. Max. Unit Output Signal - R/G/B_OUT, INT, FBLK (Ta = 25C VDDA = VDD = 5 V , CLOAD = 30pF) Rise Time Fall Time Input Signal - HFLB, VFLB Horizontal Flyback Signal Frequency Vertical Flyback Signal Frequency I2C Interface - SDA, SCL (Refer to Figure 3) SCL Clock Frequency Hold Time for start condition Set Up Time for stop condition Low Duration of clock High Duration of clock Hold Time for data Set Up Time for data Time between 2 access Fall Time of SDA Rise Time of both SCL and SDA fSCL ths tsus tlow thigh thd tsud tss tfSDA trSDA 500 500 400 400 0 500 500 300 20 kHz ns ns ns ns ns ns ns ns ns fHFLB fVFLB 120 200 kHz Hz tR tF 6 6 nsec nsec tss SDA ths SCL tsud thd thigh tlow Figure 3. I2C Bus Timing Diagram 6 OSD PROCESSOR FOR MONITOR S5D2508A01 FUNCTIONAL DESCRIPTIONS Data Transmission to the S5D2508A01 According to the I2C protocol, the S5D2508A01 receives the data from a micro controller. The SDA line and the SCL line are shown in Figure 4. As shown in Figure 4, after the starting pulse, the slave address with R/W* bit and an acknowledge are transmitted in sequence, an internal register address of the S5D2508A01 is followed. The first 8-bit byte is the upper 8bits of the register address. The lower 8bits of the register address are followed after the second acknowledge. There is a data transmission format and are two address bit patterns in the S5D2508A01 as following. The slave address of the S5D2508A01 is BAH(in hexadecimal). Data Transmission Format Row Address -> Column Address -> Data Byte N -> Data Byte N+1 -> Data Byte N+2 -> .... Address Bit Pattern for Display Registers Data (a) Row Address Bit Pattern A15 X A14 X A13 X R3 - R0: Valid Data for Row Address A12 X A11 R3 A10 R2 A9 R1 A8 R0 (b) Column Address Bit Pattern A7 X A6 X A5 X C4 - C0: Valid Data for Column Address A4 C4 A3 C3 A2 C2 A1 C1 A0 C0 After addressing, data bytes are followed as the above data transmission format. The Figure 4 describes the data transmission with the I2C bus protocol. SCL SDA START SCL ... R/W IIC SLAVE ADDRESS ACK A15 A14 A13 A12 A11 A10 A9 MSB ADDRESS A8 ACK A7 A6 A5 A4 A3 A2 LSB ADDRESS A1 A0 ACK SDA D7 D6 D5 D4 D3 D2 D1 D0 DATA BYTE N(MSB DATA) ACK D7 D6 D5 D4 D3 D2 D1 D0 DATA BYTE N(LSB DATA) ACK D7 D6 D5 D4 D3 D2 D1 D0 DATA BYTE N(MSB DATA) ACK ... STOP Figure 4. SDA line and SCL line (Write Operation) 7 S5D2508A01 OSD PROCESSOR FOR MONITOR Memory Map The display RAM is addressed with the row and column number in sequence. The display RAM consists of four register groups: Character & Attribute Registers, Row Attribute Registers and Frame Control Registers-. As the display area in a monitor screen is 30 columns by 15 rows, the related Character & Attribute Registers are also 30 columns by 15 rows. Each register contains a character address and an attribute corresponding to display location on a monitor screen. And one register is composed of 16 bits. The lower 8 bits select characters out of 256 ROM fonts. The upper 7 bits are assigned to give a character attribute to a selected font. Row Attribute Registers occupy the 31th column of Display RAM and provide the row attribute of a blank mode, raster color, raster color intensity, character color intensity, horizontal character size, vertical character size. Frame Control Registers are located at the 16th row. The content of each register is described in Figure 5 and following register set. 00 01 02 Row 00 Row 01 27 28 29 30 Character & Attribute Registers (30 x 15 Character Display) Row 13 Row 14 Row 15 00 01 02 Frame Control Registers Figure 5. Memory Map of Display Registers Row Attribute Registers 8 OSD PROCESSOR FOR MONITOR S5D2508A01 ROM Fonts S5D2508A01 is able to supply 256 single-color ROM fonts for describing an OSD icon. So a multi-language OSD icon can be generated. The standard font $00 is reserved for blank data. $00 $01 $02 $0E $0F $10 $11 $12 $1E $1F $20 $21 $22 $2E $2F $E0 $E1 $E2 $EE $EF $F0 $F1 $F2 $FE $FF Figure 6. Array of ROM Fonts 9 S5D2508A01 OSD PROCESSOR FOR MONITOR Scroll The scrolling function is to display or erase a character slowly from the top line to the bottom. The scrolling time is controlled by 'ScrT' bit of the frame control registers. If 'ScrT' bit is high, then the time is 0.5 sec. Otherwise, 1 sec. Character Bordering & Shadowing Bordering Shadowing 10 OSD PROCESSOR FOR MONITOR S5D2508A01 Character Height Control Two examples of the height-controlled character are shown in the following figure. The height control is performed by repeating some lines. The repeating line-number comes from the equation below. [# of the repeating lines = 2 + N x M ] , where N = 1,2,3,... and M = round{14/(CH[5:0]-18)}. If the M value is less than or equal to 1, all the lines of the standard font are repeated once or more. This is described as following. (i) If CH[5:0] is greater than 32, and less than or equal to 46 (32 < CH[5:0] 46), then all lines are repeated once or twice. The lines repeated twice are selected by the following equation. [# of the repeating lines = 2 + N x M ] , where N = 1,2,3,... and M= round{14/(CH[5:0]-32)}. (ii) If CH[5:0] is greater than 46, and less than or equal to 60 (46 < CH[5:0] 60), then all lines are repeated twice or three times. The lines repeated three times are selected by the following equation. [# of the repeating lines = 2 + N x M ] , where N = 1,2,3,... and M= round{14/(CH[5:0]-46)}. iii) If CH[5:0] is greater than 60, and less than or equal to 64 (60 < CH[5:0] 64), then all lines are repeated three or four times. The lines repeated four times are selected by the following equation. [# of the repeating lines = 2 + N x M ] , where N = 1,2,3,... and M= round{14/(CH[5:0]-60)}. The repeating line-number is limited to 16. 11 S5D2508A01 OSD PROCESSOR FOR MONITOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 : added line Standard Font(12*18) Standard font in high vertical resolution 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Height-controlled font : added line Standard Font(12*18) Standard font in more higher vertical resolution Height-controlled font 12 OSD PROCESSOR FOR MONITOR S5D2508A01 FRAME CONTROL & TIMING Figure 7 shows the composition of display frame with the OSD characters. HFLB HP[7:0] VP[7:0] 30 Columns(=30 x 12 dots) 15 Rows(15 x 18 dots) OSD Characters Background Screen Figure 7. Frame Composition with the OSD Characters User can determine the dot frequency by the equation of H freq. x the number of horizontal resolution. And the number of horizontal resolution is determined by the bit9 - 8 (dot 1,dot 0) of the frame Control registers-1. If dot 0 = "0", dot 1 = "0", then the dot frequency is calculated by the equation of H freq. x 320. If the H freq. = 15 kHz, then the dot frequency is 15 kHz x 320 = 4.8 MHz. If dot 0 = "1", dot 1 = "1" and the horizontal frequency is 120 kHz, then the dot frequency is 120 kHz x 800 = 96 MHz. 96 MHz is the maximum clock frequency in this processor. 13 S5D2508A01 OSD PROCESSOR FOR MONITOR REGISTER DESCRIPTION Character & Attribute Register : Row00~14, Column00~29 F E D C B A 9 8 7 6 5 4 3 2 1 0 BINV BOX1 BOX0 B G R Blink - C7 C6 C5 C4 C3 C2 C1 C0 Character Attribute Character Code 256 Fonts) Row Attribute Register : Row00~14, Column30 F E D C B A 9 8 7 6 5 4 3 2 1 0 - BREN INTE CBli BOXE BORD SHA RB RG RR RINT CINT HZ1 HZ0 VZ1 VZ0 Raster Color Intensity Character Size Frame Control Register 0 : Row15, Column00 F E D C B A 9 8 7 6 5 4 3 2 1 0 - Fde FdeT VPOL HPOL - - - - Erase EN ScrI ScrT Bli1 Bli0 BliT Frame Control Register 1 : Row15, Column01 F E D C B A 9 8 7 6 5 4 3 2 1 0 CP1 CP0 Fpll HF2 HF1 HF0 dot1 dot0 DPLL FBLK CH5 CH4 CH3 CH2 CH1 CH0 PLL Control Character Height Control Frame Control Register 2 : Row15, Column02 F E D C B A 9 8 7 6 5 4 3 2 1 0 HP7 HP6 HP5 HP4 HP3 HP2 HP1 HP0 VP7 VP6 VP5 VP4 VP3 VP2 VP1 VP0 Horizontal Start Position Vertical Start Position 14 OSD PROCESSOR FOR MONITOR S5D2508A01 Table 4. Register Description Registers Character & Attribute Register (Row 00-- 14, Column 00~29) Bits C7-- C0 (Bit 7-- 0) Blink/FINT (Bit 9) Description Character Code Address of 256 ROM Fonts. Character Blinking/Font Intensity Enable. If INTE'bit is low, this bit control blinking effect. The blinking period is ` set by the 'BliT' bit and the duty is selected by the 'Bli0' and ' Bli1' bits. If INTE'bit is high, this bit control the font intensity combined with ` INTE' RINT'and CINT'as following table. ` ,` ` INTE Blink/FINT RINT 0 0 1 1 1 1 B,G,R (Bit C-- A) BOX 1, BOX0 (Bit E, D) 0 1 0 1 1 1 0 1 1 CINT 1 0 1 Function Normal Blink Normal(No Intensity) Character Intensity Raster Intensity Character & Raster Intensity Character color is determined by these bits. 8 colors can be selected and the color intensity of a character is given by 'CINT' bit of Row Attribute Regisers. So user can select up to 16 colors. Character Box Drawing. The combinations of this two bits generate four different box drawing modes as following. The following example is the case that box dawing is activated with the font 'A' BOX0 0 BOX1 1 0 BOX OFF A A 1 A * Bit F-- D(RB/RG/RR) is also used for raster color by setting the 'BOXE' bit low. if the 'BOXE' bit is low,Raster color of a font is determined by this bits . Priority of raster color selected here is higher than that of row attribute. 15 KA2201 1.2W AUDIO POWER AMP Table 4. Register Description (Continued) Registers Bits BINV (Bit F) Row Attribute Register (Row 00 ~ 14, Column 30) VZ1,VZ0 (Bit 1, 0) Description Box Inversion. The box drawing activated by the bit E and D is changed to white box from black and conversely. Vertical Character Size Control. Vertical character size is determined by the combinations of this two bits as following table. VZ1 0 0 1 1 HZ1,HZ0 (Bit 3, 2) VZ0 0 1 0 1 Vertical Character Size 1X 2X 3X 4X Horizontal Character Size Control. The horizontal character size is determined by the combinations of this two bits as following table. HZ1 0 0 1 1 HZ0 0 1 0 1 Horizontal Character Size 1X 2X 3X 4X CINT (Bit 4) RINT (Bit 5) RB,RG,RR (Bit 8-- 6 ) SHA BORD Character Color Intensity. If INTE'bit and this bit is set, the color ` intensity of characters setting FINT'bit in the same row is high. ` Raster Color Intensity. If INTE'bit and this bit is set, the color ` intensity of rasters setting FINT'bit in the same row is high. ` Raster Color is determined by these bits. 8 colors can be selected and the color intensity of a character is given by RINT'bit of Row ` Attribute Registers. So it can be selected up to 16 colors. Character Shadowing. Set this bit to activate characters shadowing. Character Bordering. Set this bit to activate characters shadowing. OSD PROCESSOR FOR MONITOR S5D2508A01 Table 4. Register Description (Continued) Registers Bits BOXE (Bit B) Description BOX Enable. If this bit is set, Bit F-D in the Character & Attribute Registers are used for the box-drawing function. Otherwise,those are used for raster color of a font. Even though the raster color attribute is given by Bit 8-6 in the row attribute registers, the priority of Bit F-D in the character & attribute registers is higher. Color Blink Enable. If this bit is high, color blinking effect is activated. The effect is to repeat color inversion between character and raster. Color blinking time and the duty is controlled by Bil T, Bil 1 and Bli 0. Intensity Enable. If this bit is set, the function of RINT and CINT bit are enabled and the bit 9 of Character & Attribute Register control the font intensity effect. Otherwise, all intensity functions are disabled and the bit 9 of Character & Attribute Register control the blinking effect. Back Raster Blank Enable. If this bit is high and the raster color is black, the raster is transparent Reserved CBli (Bit C) INTE (Bit D) BREN (Bit E) Bit F 17 S5D2508A01 OSD PROCESSOR FOR MONITOR Table 4. Register Description (Continued) Registers Frame Control Register 0 (Row 15, Column 00) Bits Bli T (Bit 0) Bli 1,Bli 0 (Bit 2,1) Description Blink Time Control. If this bit is high, the blink time is 0.5 sec. Otherwise, 1 sec. Blinking Duty Control. The blinking duty is controlled by the combination of this two bits as following. Bli 1 0 0 1 1 ScrT (Bit 3) Scrl (Bit 4) EN (Bit 5) Erase (Bit 6) Bit A -- 7 HPOL (Bit B) VPOL (Bit C) FdeT (Bit D) Fde (Bit E) Bit F Bli 0 0 1 0 1 Blinking Duty Blink Off Duty 25% Duty 50% Duty 75% Scroll Time Control. If this bit is high, the scroll time is 0.5 sec. Otherwise, 1 sec. Scroll Enable. The scroll display is activated by setting this bit high. OSD Enable. If this bit is high, OSD is enable. Otherwise, disable. RAM Erasing. RAM data are erased by setting this bit. Reserved. Polarity of Horizontal Fly Back Signal. Positive 1, Negative 0 Polarity of Vertical Fly Back Signal. Positive 1, Negative 0 Fade-in and fade-out Time Control. If this bit is high, the time is 0.5 sec. Otherwise, 1 sec. Fade-in and fade-out Enable. The fade-in and fade-out effect is activated by setting this bit high. Reserved. 18 OSD PROCESSOR FOR MONITOR S5D2508A01 Table 4. Register Description (Continued) Registers Bits Description Frame Control Register 1 CH5-- CH0 Character Height Control. The vertical character size is determined (Row 15, Column 01) (Bit 5-- 0) by the bit 'VZ1' and VZ0'. According to the value made by this six bits, the character height is determined. If the value is 32, the number of vertical pixel of character font is 32. Eventually, the character height is expanded from 18 to 63. The binary vlaue must be greater than 18. FBLK (Bit 6) DPLL (Bit 7) dot 1,dot 0 (Bit 9,8) It determines the configuration of FBLK output pin. When it is clear, FBLK pin outputs high during displaying characters or rasters. Otherwise,FBLK pin outputs high only during displaying characters. It determines the PLL scheme. If this bit is low, then the PLL mode is differential mode. Otherwise, single mode. This two bits determine the number of dots per horizontal line. dot 1 0 0 1 1 HF2-- HF0 (Bit C-- A) dot 0 0 1 0 1 No. of Dots 320 dots/line 480 dots/line 640 dots/line 800 dots/line The horizontal frequency information is transferred by this three bits. HF2 0 0 0 0 1 1 1 1 HF1 0 0 1 1 0 0 1 1 HF0 0 1 0 1 0 1 0 1 Hf Information 15 KHz < Hf < 20 KHz 20 KHz Hf <35 KHz 35 KHz Hf < 50 KHz 50 KHz Hf < 65 KHz 65 KHz Hf <80 KHz 80 KHz Hf < 95 KHz 95 KHz Hf < 110 KHz 110 KHz Hf < 120 KHz FPLL (Bit D) CP 1,CP 0 (Bit F,E) If this bit is high, the VCO block of OSD_PLL operates on full range (4MHz - 96 MHz). This bit controls charge pump output current. CP 1 0 0 1 1 CP 0 0 1 0 1 Charge Pump Current 0.5mA 0.75mA 1.0mA 1.25mA 19 S5D2508A01 OSD PROCESSOR FOR MONITOR Table 4. Register Description (Continued) Registers Frame Control Register 2 (Row 15, Column 02) Bits VP7-- VP0 (Bit 7-- 0) HP7-- HP0 (Bit F-- 8) Description Vertical Start Position Control. It means the top margin height from the V-sync reference edge. ( = VP[7:0] x 4 ) Horizontal Start Position Control. It means the horizontal display delay from the H-sync reference edge to the 1'st pixel position of characters. ( = HP[7:0] x 6 ) 20 OSD PROCESSOR FOR MONITOR S5D2508A01 STANDARD ROM FONTS 21 S5D2508A01 OSD PROCESSOR FOR MONITOR 22 OSD PROCESSOR FOR MONITOR S5D2508A01 APPLICATION CIRCUIT VCC=5V + 100uF 104 1 VSS_A VDD_D 16 + 100uF 104 INT 5.6K 101 392 2 VCO_IN INT 15 400 R_OUT 36K 100uF G_OUT 4 VDD_A G_OUT 13 3 VREF1 R_OUT 14 400 104 Bead 1uH VCC 4.7uF 104 + + 400 5 S 5KS2508 D2508A VREF B_OUT 12 400 B_OUT 470 VCC 6 HFLB FBLK 11 400 FBLK HFLB 120 120 102 2N3904 4.7K 4.7K 2K 7 SDA VSS_D 10 6.2K 2K 8 SCL VFLB 9 VFLB 120 2.2nF 1 2 SDA SCL 23 S5D2508A01 OSD PROCESSOR FOR MONITOR NOTES 24 |
Price & Availability of S5D2508A01-D0B0
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |