![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Preliminary W91310N SERIES TONE/PULSE DIALER WITH FLASH TIME STOREABL AND SAVE FUNCTIONS GENERAL DESCRIPTION The W91310N series are monolithic Ics that provide the necessary signals for either pulse or tone dialing. The W91310N series feature a redial memory, Handsfree, auto redial function, and flash time storeable. FEATURES * * * * * * * * * * * * * * DTMF/Pulse switchable dialer 32 digits for redial memory Pulse-to-tone (PT) keypad for long distance call operation Break/Make ratio is selectable by pin option Uses 5 x 5 keyboard Easy operation with redial, flash, pause, and PT keypads Flash, pause, PT (pulse-to-tone) can be stored as a digit in memory Minimum tone output duration: 93 mS Minimum intertone pause: 93 mS On-chip power-on reset One flash time storeable Uses 3.579545 MHz crystal or ceramic resonator Packaged in 18-pin plastic DIP, and 300 mil 20-pin SOP. The dialer in the W91310N series are shown in the following table: TYPE NO. W91310N W91310AN PULSE (ppS) 10/20 10/20 FLASH (Ms) 600/300/100/73 600/300/100/73 FLASH PAUSE (S) 1.0 1.0 PAUSE (S) 2.0/3.6 2.0/3.6 -1- Publication Release Date: January 2001 Revision A1 Preliminary W91310N SERIES PIN CONFIGURATIONS C1 C1 C2 C3 C4 B/M Vss XT XT T/P MUTE 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 R4 R3 R2 R1 VDD MODE DTMF DP HKS HFO 1 18 17 16 15 14 13 12 11 10 R4 R3 R2 R1 VDD MODE DTMF DP HKS C2 C3 C4 B/M Vss XT XT T/P MUTE HFI 2 3 4 5 6 7 8 9 W91310N W91310AN C1 C2 C3 C4 B/M NC Vss XT XT T/P MUTE 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 R4 R3 R2 R1 VDD NC MODE DTMF DP HKS W91310NS -2- Preliminary W91310N SERIES PIN DESCRIPTION SYMBOL ColumnRow Inputs PIN DIP 1-4 & 15-18 (17-20)/ (AN) PIN SSOP I/O I FUNCTION The keyboard input may be from either the standard 4 x 4 keyboard or an inexpensive single contact (form A) keyboard. Electronic input from a C can also be used. A valid key entry is defined as a single row being connected to a single column. A built-in inverter provides oscillation with an inexpensive 3.579545 MHz crystal or ceramic resonator. The T/P MUTE is a conventional CMOS N-channel open drain output. The output transistor is switched on during pulse and tone mode dialing sequence and flash break. Otherwise, it is switched off. Pulling mode pin to VSS places the dialer in tone mode. Pulling mode pin to VDD places the dialer in pulse mode (10 ppS). Leaving mode pin floating places the dialer in pulse mode (20 ppS). Hook switch input. HKS = 1: On-hook state. Chip in sleeping mode, no operation. HKS = 0: Off-hook state. Chip enabled for normal operation. The HKS pin is pulled to VDD by an internal resistor. N-channel open drain dialing pulse output (Figure 1). Flash key will cause DP to go active in both pulse mode and tone mode. In pulse mode, remains in low state at all times. In tone mode, outputs a dual or single tone. Detailed timing diagram for tone mode is shown in Figure 2(a, b). OUTPUT FREQUENCY Specified R1 R2 R3 R4 C1 C2 C3 697 770 852 941 1209 1336 1477 Actual 699 766 848 948 1216 1332 1472 Error % +0.28 -0.52 -0.47 +0.74 +0.57 -0.30 -0.34 1-4 & 17-20 XT, XT T/P MUTE 7, 8 9 8, 9 10 I, O O MODE 13 15(AN) 14 I HKS 10 12(AN) 11 I DP 11 13(AN) 12 O DTMF 12 14(AN) 13 O VDD, VSS B/M 14, 6 16, 6 (AN) 16, -7 5 I I Power input pins. The break make ratio is 60:40 if B/M = 1 and is 66.6:33.3 if B/M = 0. This pin has no function in DTMF mode. 5 -3- Publication Release Date: January 2001 Revision A1 Preliminary W91310N SERIES Pin Description, continued SYMBOL HFI, HFO PIN DIP 11, 12 (AN Only) PIN SSOP I/O I, O Handfree control pins. FUNCTION - A low pulse on the HFI input pin toggles the handfree control state. The status of the handfree control state is listed in the following table: CURRENT STATE HOOK SW. HFO INPUT NEXT STATE HFO DIALING On Hook Off Hook On Hook Off Hook Off Hook Low High High Low High HFI HFI HFI Off Hook On Hook On Hook High Low Low Low Low High Yes No Yes Yes No Yes The HFI pin is pulled to VDD by an internal resistor. A detailed timing diagram is shown in Figure 3. BLOCK DIAGRAM XT XT HKS B/M MODE SYSTEM CLOCK GENERATION HFI READ/WRITE COUNTER ROW (R1 to R4) KEYBOARD INTERFACE RAM CONTROL LOGIC PULSE CONTROL LOGIC T/P MUTE HFO DP COLUMN (C1 to C4) LOCATION LATCH DTMF D/A CONVERTER ROW & COLUMN PROGRAMMABLE COUNTER DATA LATCH & DECODER -4- Preliminary W91310N SERIES FUNCTIONAL DESCRIPTION Keyboard Operation C1 1 4 7 */T R/P2 * * * * * * * * C2 2 5 8 0 RD C3 3 6 9 # F3 C4 SAVE F1 F2 R/P1 F4 DP / C5 MEM R1 R2 R3 RD R4 VDD R/P: Redial and pause function key */T: * in tone mode and PT: Pulse mode to tone mode S: Store function MEM: With the same memory location as SAVE memory SAVE: Save function memory R/P1, R/P2: Redial and pause function key, P1 is 3.6 sec, and P2 is 2.0 sec. F1, ...F4: Flash key , RD: One key redial. Normal Dialing OFF HOOK , (or ON HOOK & HFI o ), D1 , D2 , ..., Dn 1. D1, D2, ..., Dn will be dialed out. 2. Dialing length is unlimited, but redial is inhibited if length oversteps 32 digits. Redialing 1. OFF HOOK Busy, come , (or ON HOOK , & HFI o (or ), D1 , & D2 , ..., Dn R/P ON HOOK OFF HOOK ON HOOK HFI o ), 1. The redial memory content will be D1, D2, ...Dn. , b. The R/P key can execute the redial function only as the first key-in after off-hook; otherwise, it will invoke the pause function. c. If redialing length oversteps 32 digits, the redialing function will be inhibits. Save OFF HOOK or ON HOOK , HFI o , D1 , D2 , ..., Dn , SAVE . 1. D1, D2, ... Dn will be dialed out . ., -5- Publication Release Date: January 2001 Revision A1 Preliminary W91310N SERIES 2. If the sequence of the dialed digits D1, D2, ... Dn has not finished, ., otherwise, D1, D2, ... Dn will be duplicated to SAVE memory. ., SAVE will be ignored; Repertory Dialing One-touch direct repertory dialing: 1. 2. OFF HOOK OFF HOOK (or (or ON HOOK ON HOOK , , HFI o HFI o , , MEN SAVE . . Press MEM will dial out the same as pressing SAVE . Access Pause OFF HOOK , (or ON HOOK , HFI o ) D1 , D2 , R/P , D3 , ..., Dn 1. The pause function can be stored in memory. 2. The pause function is executed in normal dialing or memory dialing. 3. The pause function timing diagram is shown in Figure 5. Pulse-to-tone (PT) OFF HOOK (or ON HOOK , HFI o ) D1 , D2 , ..., Dn , PT , D1' , D2' , ..., Dn' 1. If the mode switch is set to pulse mode, then the output signal will be: D1, D2, ..., Dn, Pause, D1', D2', ..., Dn' (Pulse) (Tone) 2. If the mode switch is set to tone mode, then the output signal will be: D1, D2, ..., Dn, (Tone) PT (Pause) D1, D2, ..., Dn, (Tone) 1. The dialer remains in tone mode when the digits have been dialed out and can be reset to pulse mode only by going on-hook. 4. The PT function timing diagram is shown in Figure 6. Flash OFF HOOK , (or ON HOOK , HFI o ), Fn 1. Flash key can be stored as a digit in memory. 2. Only one flash key can be released to end user. 3. The system will return to the initial state after the break time is finished. -6- Preliminary W91310N SERIES 4. If the mode switch is set in pulse mode, after the dialing sequence D1, D2. */T, D3, Fn, D4, the dialer will keep in tone mode. 5. The flash function timing diagram is shown in Figure 7. Mixed Dialing 1. Definition of mixed dialing: In mixed dialing, a new sequence may be accepted only when the previous sequence has been dialed out completely. The following are examples of mixed dialing: Example 1: Normal dialing + (1st sequence) Example 2: Repertory dialing 1 (1st sequence) Example 3: Redialing + + Repertory dialing 1 (2nd sequence) Normal dialing (2nd sequence) Normal dialing (2nd sequence) + + + Repertory dialing 2 + ..... ... (3rd sequence) Repertory dialing 2 (3rd sequence) +...... .... + ...... ... Repertory dialing 1 (3rd sequence) (1st sequence) 2. There is no limitation on the number of digits and sequences in the mixed dialing. 3. The content of mixed dialing may be a combination of normal dialing, memory dialing, or one-key redialing. 4. If ON HOOK , OFF HOOK (or ON HOOK & HFI o ), RD is entered, then the mixed dialing sequence described in the above examples will be dialed out only if the total number of digits does not exceed 32. If the total exceeds 32 digits, then redialing is inhibited. -7- Publication Release Date: January 2001 Revision A1 Preliminary W91310N SERIES ABSOLUTE MAXIMUM RATINGS PARAMETER DC Supply Voltage Input/Output Voltage SYMBOL VDD-VSS VIL VIH VOL VOH Power Dissipation Operating Temperature Storage Temperature PD TOPR TSTG RATING -0.3 to +7.0 VSS -0.3 VDD +0.3 VSS -0.3 VDD +0.3 120 -20 to +70 -55 to +125 UNIT V V V V V mW C C Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. DC CHARACTERISTICS (VDD-VSS = 2.5V, Fosc. = 3.58 MHz, TA = 25 C, all outputs unloaded) PARAMETER Operating Voltage Operating Current Standby Current Memory Retention Current DTMF Output Voltage Pre-emphasis DTMF Distortion DTMF Output DC Level DTMF Output Sink Current DP Output Sink Current T/P MUTE Output Sink Current HKS I/P Pull-high Resistor HFO Drive/Sink Current SYM. VDD IOP ISB IMR VTO THD VTDC ITL IPL IML RKH IHFH IHFL CONDITIONS Tone, Unloaded Pulse, Unloaded HKS = 0, No load, & No key entry HKS = 1, VDD = 1.0V Row group, RL = 5 K Col/Row, VDD = 2.0 to 5.5V RL = 5 K, VDD = 2.0 to 5.5V RL = 5 K, VDD = 2.0 to 5.5V VTO = 0.5V VPO = 0.5V VMO = 0.5V MIN. 2.0 130 1 1.0 0.2 0.5 0.5 - TYP. 0.4 0.2 150 2 -30 300 - MAX. 5.5 0.6 0.4 15 0.2 170 3 -23 3.0 - UNIT V mA mA A A mVrms dB dB V mA mA mA K mA mA VHFH = 2.0 V VHFL = 0.5 V 0.5 0.5 -8- Preliminary W91310N SERIES DC Characteristics, continued PARAMETER Keypad Input Drive Current Keypad Input Sink Current Keypad Resistance SYM. IKD IKS CONDITIONS VI = 0V VI = 2.5V MIN. 30 200 - TYP. 400 - MAX. 5.0 UNIT A A K AC CHARACTERISTICS PARAMETER Keypad Active in Debounce Key Release Debounce Pre-digit Pause1 Pre-digit Pause2 SYMBOL TKID TKRD TPDP1 10 ppS TPDP2 20 ppS Interdigit Pause (Auto dialing) Make/Break Ratio DTMF Output Duration Intertone Pause Flash Break Time TIDP M/B TTD TITP TFB B/M = 1 B/M = 0 B/M = 1 B/M = 0 10 ppS 20 ppS B/M = 1 B/M = 0 Auto Dialing Auto Dialing F1 F2 F3 F4 Flash Pause Time One Key Redial Break Time One Key Redial Pause Time Pause Time TFP TRB TRP TP R/P1 R/P2 Notes: 1. Crystal parameters suggested for proper operation are Rs < 100 , Lm = 96 mH, Cm = 0.02 pF, Cn = 5 pF, Cl = 18 pF, FOSC. = 3.579545 MHz 0.02%. 2. Crystal oscillator accuracy directly affects these times. 1. Pause Time selectable. 2. Flash time only can be use any one in any same time. CONDITIONS MIN. - TYP. 20 20 40 33.3 20 16.7 800 500 40:60 33:67 93 93 600 100 300 73 1.0 2.2 0.6 3.6 2.0 MAX. - UNIT mS mS mS mS mS % mS mS mS F1, F2, F3, F4 - S S S S -9- Publication Release Date: January 2001 Revision A1 Preliminary W91310N SERIES TIMING WAVEFORMS HKS <600ms <300ms KEY IN 4 T KID 2 2 B DP T PDP M TIDP TIDP T IDP T/P MUTE DTMF LOW OSC. OSCILLATION NORMAL DIALING OSCILLATION Figure 1(a). Normal Dialing Timing Diagram (Pulse Mode Timing Diagram) HKS <600ms TKRD KEY IN R/P T KID DP B M TPDP TIDP TIDP TIDP T/P MUTE LOW DTMF OSC. ON HOOK OSCILLATION AUTO DIALING Figure 1(b). Auto Dialing Timing Diagram (Pulse Mode Timing Diagram) - 10 - Preliminary W91310N SERIES Timing Waveforms, continued HKS <600ms <300ms KEY IN TKID TITP TKRD TKRD TITP TKID TITP DTMF TTD T/P MUTE DP HIGH OSC. OSCILLATION NORMAL DIALING OSCILLATION Figure 2(a). Normal Dialing Timing Diagram (Tone Mode Timing Diagram) HKS KEY IN R/P TKID DTMF TTD T ITP T/P MUTE T ITP DP HIGH OSC. OSCILLATION Figure 2(b). Auto Dialing Timing Diagram (Tone Mode Auto Dialing Timing Diagram) - 11 - Publication Release Date: January 2001 Revision A1 Preliminary W91310N SERIES Timing Waveforms, continued HKS OFF HOOK HFI HFO T/P MUTE HIGH CHIP ENABLE Figure 3. Handfree Timing Diagram HKS <600ms TKRD KEY IN RD RD T KID DP TOFD 300ms TKID M B TRB TRP TPDP TIDP TPDP T/P MUTE LOW HFO OSC. ON HOOK OSCILLATION AUTO DIALING Figure 4 One -key redial Timing Diagram (Pulse mode) - 12 - Preliminary W91310N SERIES Timing Waveforms, continued HKS 600ms 300ms TOFD KEY IN 4 TKID 2 R/P 2 DP B TPDP M TIDP B M TIDP B M TIDP T/P MUTE DTMF LOW TP TFKD OSC. OSCILLATION OSCILLATION Figure 5. Pause Function Timing Diagram HKS 600ms KEY IN 300ms 4 TKID 2 P T 8 TOFD DP B TPDP M TIDP B M TIDP T/P MUTE DTMF TP TFKD OSC. OSCILLATION OSCILLATION Figure 6. Pulse-to-tone Function Timing Diagram - 13 - Publication Release Date: January 2001 Revision A1 Preliminary W91310N SERIES Timing Waveforms, continued HKS Low KEY IN F TKID 4 DP TFB TFP TTD DTMF TITP T/P MUTE OSC. OSCILLATION Figure 7. Flash Function Timing Diagram - 14 - Preliminary W91310N SERIES APPLICATION CIRCUIT TIP D1-D4 1N4004 VR1 250V R5 10M Q1 A94 R3 33K R6 3K D7 1N4148 RING ON HOOK OFF HOOK R4 3K3 D5 R1 200K Q2 A42 C1 100uF D8 5V1 1N4148 R9 470K SPEECH NETWORK R7 1M R10 10K Q4 C1815 R11 75 R8 300K Q3 9013 C10 0.1uF R12 22K C4 4u7 R4 R3 1 4 7 */T R/P2 2 5 8 0 RD 3 6 9 # F3 SAVE F1 F2 R/P1 F4 RD C1 C2 MEM S R2 R1 VDD HKS DP HFO DTMF HFI W91310 N SERIES VDD C3 C4 DP/C5 B/M VSS XT XT T/P MUTE VDD PULSE Tone X1 C5 30P 3.58MHz C6 30P R18 22K Q7 9013 - 15 - Publication Release Date: January 2001 Revision A1 Preliminary W91310N SERIES Headquarters Winbond Electronics (H.K.) Ltd. Unit 9-15, 22F, Millennium City, No. 4, Creation Rd. III, No. 378 Kwun Tong Rd; Science-Based Industrial Park, Kowloon, Hong Kong Hsinchu, Taiwan TEL: 852 -27513100 TEL: 886-3-5770066 FAX: 852 -27552064 FAX: 886 -3-5792766 http://www.winbond.com.tw/ Voice & Fax-on-demand: 886 -2-27197006 Winbond Electronics North America Corp. Winbond Memory Lab. Winbond Microelectronics Corp. Winbond Systems Lab. 2727 N. First Street, San Jose, CA 95134, U.S.A. TEL: 408-9436666 FAX: 408-5441798 Taipei Office 11F, No. 115, Sec. 3, Min -Sheng East Rd., Taipei, Taiwan TEL: 886-2-27190505 FAX: 886 -2-27197502 Note: All data and specifications are subject to change withou t notice. - 16 - |
Price & Availability of W91310N
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |