View MC9S12D64_290642.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DOCUMENT NUMBER 9S12DJ64DGV1/D
MC9S12DJ64 Device User Guide V01.10 Covers also MC9S12D64, MC9S12A64
Original Release Date: 19 Nov 2001 Revised: 8 November, 2002
Motorola, Inc
Motorola reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Motorola does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
1
Revision History
Version Revision Effective Number Date Date
V01.00 16 NOV 2001 18 FEB 2002 19 NOV 2001 18 FEB 2002
Author
Description of Changes
Initial version based on MC9SDP256-2.09 Version. In table "5V I/O Characteristics" of the electrical characteristics replaced tPULSE with tpign and tpval in lines "Port ... Interrupt Input Pulse filtered" and "Port ... Interrupt Input Pulse passed" respectively. Table "Oscillator Characterisitcs" : removed "Oscillator start-up time from POR or STOP" row Table "5V I/O Characteristics" : Updated Partial Drive IOH = +-2mA and Full Drive IOH = -10mA Table "ATD Operating Characteristics": Distinguish IREFfor 1 and 2 ATD blocks on Table "ATD Electrical Characteristics": Update CINS to 22 pF Table "Operating Conditions": Changed VDD and VDDPLL to 2.35 V (min) Removed Document number except from Cover Sheet Updated Table "Document References" Table "5V I/O Characteristics" : Corrected Input Capacitance to 6pF Section: "Device Pinout" (112-pin and 80-pin): added in diagrams RXCAN0 to PJ6 and TXCAN0 to PJ7 Table "PLL Characteristics": Updated parameters K1 and f1 Figure "Basic Pll functional diagram": Inserted XFC pin in diagram Enhanced section "XFC Component Selection" Added to Sections ATD, ECT and PWM: freeze mode = active BDM mode Added 1L86D to Table "Assigned Part ID numbers" Corrected MEMSIZ1 value in Table "Memory size registers" Subsection "Device Memory Map: Removed Flash mapping from $0000 to $3FFF. Table "Signal Properties": Added column "Internal Pull Resistor". Preface Table "Document References": Changed to full naming for each block. Table "Interrupt Vector Locations", Column "Local Enable": Corrected several register and bit names. Figure "Recommended PCB Layout for 80QFP: Corrected VREGEN pin position Thermal values for junction to board and package BGND pin pull-up Part Order Information Global Register Table Chip Configuration Summary Modified mode of Operations chapter Section "Printed Circuit Board Layout Proposals": added Pierce Oscillator examples for 112LQFP and 80QFP
V01.01
V01.02
6 MAR 2002
6 MAR 2002
V01.03
4 June 2002
4 June 2002
V01.04
4 July 2002
4 July 2002
V01.05
30 July 2002
30 July 2002
MC9S12DJ64 Device User Guide -- V01.10
Version Revision Effective Number Date Date
V01.06 20 Aug. 2002 20 Aug. 2002
Author
Description of Changes
NVM electricals updated Subsection "Detailed Register Map: Address corrections Preface, Table "Document references": added OSC User Guide New section "Oscillator (OSC) Block Description" Electrical Characteristics: -> Section "General": removed preliminary disclaimer ->Table "Supply Current Characteristics": changed max Run IDD from 65mA to 50mA changes max Wait IDD from 40mA to 30mA changed max Stop IDD from 50uA to 100uA Section HCS12 Core Block Desciption: mentioned alternalte clock of BDM to be equivalent to oscillator clock Table "5V I/O Characteristics": Corrected Input Leakage Current to +/- 1 uA Section "Part ID assignment": Located on start of next page for better readability Added MC9S12A64 derivative to cover sheet and "Derivative Differences" Table Corrected in footnote of Table "PLL Characteristics": fOSC = 4MHz Renamed "Preface" section to "Derivative Differences and Document references". Added details for derivatives missing CAN0 and/or BDLC Table "ESD and Latch-up Test Conditions": changed pulse numbers from 3 to 1 Table "ESD and Latch-Up Protection Characteristics": changed parameter classification from C to T Table "5V I/O Characteristics": removed foot note from "Input Leakage Current" Table " Supply Current Characteristics": updated Stop and Pseudo Stop currents
V01.07
20 Sept. 2002
20 Sept. 2002
V01.08
25 Sept. 2002
25 Sept. 2002
V01.09
10 Oct. 2002
10 Oct. 2002
V01.10
8 Nov. 2002
8 Nov. 2002
3
MC9S12DJ64 Device User Guide -- V01.10
4
MC9S12DJ64 Device User Guide -- V01.10
Table of Contents
Section 1 Introduction
1.1 1.2 1.3 1.4 1.5 1.5.1 1.6 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Device Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Detailed Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Part ID Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Section 2 Signal Description
2.1 Device Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 2.2 Signal Properties Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 2.3 Detailed Signal Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 2.3.1 EXTAL, XTAL -- Oscillator Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 2.3.2 RESET -- External Reset Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 2.3.3 TEST -- Test Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 2.3.4 VREGEN -- Voltage Regulator Enable Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 2.3.5 XFC -- PLL Loop Filter Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 2.3.6 BKGD / TAGHI / MODC -- Background Debug, Tag High, and Mode Pin . . . . . . . .52 2.3.7 PAD15 / AN15 / ETRIG1 -- Port AD Input Pin of ATD1 . . . . . . . . . . . . . . . . . . . . . .52 2.3.8 PAD[14:08] / AN[14:08] -- Port AD Input Pins ATD1 . . . . . . . . . . . . . . . . . . . . . . . .53 2.3.9 PAD07 / AN07 / ETRIG0 -- Port AD Input Pin of ATD0 . . . . . . . . . . . . . . . . . . . . . .53 2.3.10 PAD[06:00] / AN[06:00] -- Port AD Input Pins of ATD0 . . . . . . . . . . . . . . . . . . . . . .53 2.3.11 PA[7:0] / ADDR[15:8] / DATA[15:8] -- Port A I/O Pins . . . . . . . . . . . . . . . . . . . . . . .53 2.3.12 PB[7:0] / ADDR[7:0] / DATA[7:0] -- Port B I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . .53 2.3.13 PE7 / NOACC / XCLKS -- Port E I/O Pin 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 2.3.14 PE6 / MODB / IPIPE1 -- Port E I/O Pin 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 2.3.15 PE5 / MODA / IPIPE0 -- Port E I/O Pin 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 2.3.16 PE4 / ECLK -- Port E I/O Pin 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 2.3.17 PE3 / LSTRB / TAGLO -- Port E I/O Pin 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 2.3.18 PE2 / R/W -- Port E I/O Pin 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 2.3.19 PE1 / IRQ -- Port E Input Pin 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 2.3.20 PE0 / XIRQ -- Port E Input Pin 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
5
MC9S12DJ64 Device User Guide -- V01.10
2.3.21 2.3.22 2.3.23 2.3.24 2.3.25 2.3.26 2.3.27 2.3.28 2.3.29 2.3.30 2.3.31 2.3.32 2.3.33 2.3.34 2.3.35 2.3.36 2.3.37 2.3.38 2.3.39 2.3.40 2.3.41 2.3.42 2.3.43 2.3.44 2.3.45 2.3.46 2.3.47 2.3.48 2.3.49 2.3.50 2.3.51 2.3.52 2.3.53 2.3.54 2.3.55 2.3.56
PH7 / KWH7 -- Port H I/O Pin 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 PH6 / KWH6 -- Port H I/O Pin 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 PH5 / KWH5 -- Port H I/O Pin 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 PH4 / KWH4 -- Port H I/O Pin 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 PH3 / KWH3 -- Port H I/O Pin 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 PH2 / KWH2 -- Port H I/O Pin 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 PH1 / KWH1 -- Port H I/O Pin 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 PH0 / KWH0 -- Port H I/O Pin 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 PJ7 / KWJ7 / SCL / TXCAN0 -- PORT J I/O Pin 7 . . . . . . . . . . . . . . . . . . . . . . . . . .56 PJ6 / KWJ6 / SDA / RXCAN0 -- PORT J I/O Pin 6 . . . . . . . . . . . . . . . . . . . . . . . . . .57 PJ[1:0] / KWJ[1:0] -- Port J I/O Pins [1:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 PK7 / ECS / ROMCTL -- Port K I/O Pin 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 PK[5:0] / XADDR[19:14] -- Port K I/O Pins [5:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 PM7 -- Port M I/O Pin 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 PM6 -- Port M I/O Pin 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 PM5 / TXCAN0 / SCK0 -- Port M I/O Pin 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 PM4 / RXCAN0 / MOSI0 -- Port M I/O Pin 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 PM3 / TXCAN0 / SS0 -- Port M I/O Pin 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PM2 / RXCAN0 / MISO0 -- Port M I/O Pin 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PM1 / TXCAN0 / TXB -- Port M I/O Pin 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PM0 / RXCAN0 / RXB -- Port M I/O Pin 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PP7 / KWP7 / PWM7 -- Port P I/O Pin 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PP6 / KWP6 / PWM6 -- Port P I/O Pin 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PP5 / KWP5 / PWM5 -- Port P I/O Pin 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PP4 / KWP4 / PWM4 -- Port P I/O Pin 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PP3 / KWP3 / PWM3 -- Port P I/O Pin 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PP2 / KWP2 / PWM2 -- Port P I/O Pin 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PP1 / KWP1 / PWM1 -- Port P I/O Pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PP0 / KWP0 / PWM0 -- Port P I/O Pin 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PS7 / SS0 -- Port S I/O Pin 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PS6 / SCK0 -- Port S I/O Pin 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PS5 / MOSI0 -- Port S I/O Pin 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PS4 / MISO0 -- Port S I/O Pin 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PS3 / TXD1 -- Port S I/O Pin 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PS2 / RXD1 -- Port S I/O Pin 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 PS1 / TXD0 -- Port S I/O Pin 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
6
MC9S12DJ64 Device User Guide -- V01.10
2.3.57 PS0 / RXD0 -- Port S I/O Pin 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 2.3.58 PT[7:0] / IOC[7:0] -- Port T I/O Pins [7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 2.4 Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 2.4.1 VDDX, VSSX -- Power & Ground Pins for I/O Drivers . . . . . . . . . . . . . . . . . . . . . . .61 2.4.2 VDDR, VSSR -- Power & Ground Pins for I/O Drivers & for Internal Voltage Regulator 61 2.4.3 VDD1, VDD2, VSS1, VSS2 -- Core Power Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 2.4.4 VDDA, VSSA -- Power Supply Pins for ATD0/ATD1 and VREG . . . . . . . . . . . . . . .61 2.4.5 VRH, VRL -- ATD Reference Voltage Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . .62 2.4.6 VDDPLL, VSSPLL -- Power Supply Pins for PLL . . . . . . . . . . . . . . . . . . . . . . . . . . .62 2.4.7 VREGEN -- On Chip Voltage Regulator Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Section 3 System Clock Description
3.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Section 4 Modes of Operation
4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.4 4.4.1 4.4.2 4.4.3 4.4.4 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Chip Configuration Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Securing the Microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Operation of the Secured Microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Unsecuring the Microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Pseudo Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Wait . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Run. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Section 5 Resets and Interrupts
5.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 5.2 Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 5.2.1 Vector Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 5.3 Effects of Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 5.3.1 I/O pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 5.3.2 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Section 6 HCS12 Core Block Description
7
MC9S12DJ64 Device User Guide -- V01.10
6.1
Device-specific information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Section 7 Clock and Reset Generator (CRG) Block Description
7.1 Device-specific information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Section 8 Oscillator (OSC) Block Description
8.1 Device-specific information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Section 9 Enhanced Capture Timer (ECT) Block Description Section 10 Analog to Digital Converter (ATD) Block Description Section 11 Inter-IC Bus (IIC) Block Description Section 12 Serial Communications Interface (SCI) Block Description Section 13 Serial Peripheral Interface (SPI) Block Description Section 14 J1850 (BDLC) Block Description Section 15 Pulse Width Modulator (PWM) Block Description Section 16 Flash EEPROM 64K Block Description Section 17 EEPROM 1K Block Description Section 18 RAM Block Description Section 19 MSCAN Block Description Section 20 Port Integration Module (PIM) Block Description Section 21 Voltage Regulator (VREG) Block Description Section 22 Printed Circuit Board Layout Proposals Appendix A Electrical Characteristics
A.1 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 A.1.1 Parameter Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
8
MC9S12DJ64 Device User Guide -- V01.10
A.1.2 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 A.1.3 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 A.1.4 Current Injection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 A.1.5 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 A.1.6 ESD Protection and Latch-up Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 A.1.7 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 A.1.8 Power Dissipation and Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 A.1.9 I/O Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 A.1.10 Supply Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 A.2 ATD Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 A.2.1 ATD Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 A.2.2 Factors influencing accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 A.2.3 ATD accuracy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 A.3 NVM, Flash and EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 A.3.1 NVM timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 A.3.2 NVM Reliability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 A.4 Voltage Regulator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 A.5 Reset, Oscillator and PLL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 A.5.1 Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 A.5.2 Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 A.5.3 Phase Locked Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 A.6 MSCAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 A.7 SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 A.7.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 A.7.2 Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 A.8 External Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 A.8.1 General Muxed Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Appendix B Package Information
B.1 B.2 B.3 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 112-pin LQFP package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 80-pin QFP package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
9
MC9S12DJ64 Device User Guide -- V01.10
10
MC9S12DJ64 Device User Guide -- V01.10
List of Figures
Figure 0-1 Figure 1-1 Figure 1-2 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 3-1 Figure 22-1 Figure 22-2 Figure 22-3 Figure 22-4 Figure A-1 Figure A-2 Figure A-3 Figure A-4 Figure A-5 Figure A-6 Figure A-7 Figure A-8 Figure A-9 Figure B-1 Figure B-2 Order Partnumber Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 MC9S12DJ64 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 MC9S12DJ64 Memory Map out of Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Pin Assignments in 112-pin LQFP for MC9S12DJ64 . . . . . . . . . . . . . . . . . . . . .48 Pin Assignments in 80-pin QFP for MC9S12DJ64 . . . . . . . . . . . . . . . . . . . . . . .49 PLL Loop Filter Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Colpitts Oscillator Connections (PE7=1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Pierce Oscillator Connections (PE7=0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 External Clock Connections (PE7=0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Clock Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Recommended PCB Layout 112LQFP Colpitts Oscillator. . . . . . . . . . . . . . . . . .77 Recommended PCB Layout for 80QFP Colpitts Oscillator . . . . . . . . . . . . . . . . .78 Recommended PCB Layout for 112LQFP Pierce Oscillator . . . . . . . . . . . . . . . .79 Recommended PCB Layout for 80QFP Pierce Oscillator . . . . . . . . . . . . . . . . . .80 ATD Accuracy Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Basic PLL functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Jitter Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Maximum bus clock jitter approximation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 SPI Master Timing (CPHA = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 SPI Master Timing (CPHA =1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 SPI Slave Timing (CPHA = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 SPI Slave Timing (CPHA =1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 General External Bus Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 112-pin LQFP mechanical dimensions (case no. 987) . . . . . . . . . . . . . . . . . . 118 80-pin QFP Mechanical Dimensions (case no. 841B) . . . . . . . . . . . . . . . . . . . 119
11
MC9S12DJ64 Device User Guide -- V01.10
12
MC9S12DJ64 Device User Guide -- V01.10
List of Tables
Table 0-1 Derivative Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Table 0-2 Document References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Table 1-1 Device Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 $0000 - $000F MEBI map 1 of 3 (Core User Guide) ........................................................27 $0010 - $0014 MMC map 1 of 4 (Core User Guide) ........................................................27 $0015 - $0016 INT map 1 of 2 (Core User Guide) ...........................................................28 $0017 - $0017 MMC map 2 of 4 (Core User Guide) ........................................................28 $0018 - $001B Miscellaneous Peripherals (Device User Guide, Table 1-3) ....................28 $001C - $001D MMC map 3 of 4 (Core and Device User Guide, Table 1-4) ...................28 $001E - $001E MEBI map 2 of 3 (Core User Guide) ........................................................28 $001F - $001F INT map 2 of 2 (Core User Guide) ...........................................................28 $0020 - $0027 Reserved ..................................................................................................29 $0028 - $002F BKP (Core User Guide) ...........................................................................29 $0030 - $0031 MMC map 4 of 4 (Core User Guide) ........................................................29 $0032 - $0033 MEBI map 3 of 3 (Core User Guide) ........................................................29 $0034 - $003F CRG (Clock and Reset Generator) ..........................................................30 $0040 - $007F ECT (Enhanced Capture Timer 16 Bit 8 Channels) .................................30 $0080 - $009F ATD0 (Analog to Digital Converter 10 Bit 8 Channel) ..............................33 $00A0 - $00C7 PWM (Pulse Width Modulator 8 Bit 8 Channel) .......................................34 $00C8 - $00CF SCI0 (Asynchronous Serial Interface) ......................................................36 $00D0 - $00D7 SCI1 (Asynchronous Serial Interface) ......................................................36 $00D8 - $00DF SPI0 (Serial Peripheral Interface) ............................................................37 $00E0 - $00E7 IIC (Inter IC Bus) ......................................................................................37 $00E8 - $00EF BDLC (Bytelevel Data Link Controller J1850) ..........................................38 $00F0 - $00FF Reserved ..................................................................................................38 $0100 - $010F Flash Control Register (fts64k) ................................................................38 $0110 - $011B EEPROM Control Register (eets1k) ........................................................39 $011C - $011F Reserved for RAM Control Register ........................................................39 $0120 - $013F ATD1 (Analog to Digital Converter 10 Bit 8 Channel) ..............................40 $0140 - $017F CAN0 (Motorola Scalable CAN - MSCAN) ..............................................41 Table 1-2 Detailed MSCAN Foreground Receive and Transmit Buffer Layout . . . . . . . . . . .42 $0180 - $023F Reserved ..................................................................................................43 $0240 - $027F PIM (Port Integration Module) ..................................................................43
13
MC9S12DJ64 Device User Guide -- V01.10
$0280 - $03FF Reserved ..................................................................................................45 Table 1-3 Assigned Part ID Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Table 1-4 Memory size registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Table 2-1 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Table 2-2 MC9S12DJ64 Power and Ground Connection Summary . . . . . . . . . . . . . . . . . . .60 Table 4-1 Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Table 4-2 Clock Selection Based on PE7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Table 4-3 Voltage Regulator VREGEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Table 5-1 Interrupt Vector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Table 22-1 Suggested External Component Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Table A-1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Table A-2 ESD and Latch-up Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Table A-3 ESD and Latch-Up Protection Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Table A-4 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Table A-5 Thermal Package Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 Table A-6 5V I/O Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 Table A-7 Supply Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Table A-8 ATD Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Table A-9 ATD Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Table A-10 ATD Conversion Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 Table A-11 NVM Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Table A-12 NVM Reliability Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Table A-13 Voltage Regulator Recommended Load Capacitances . . . . . . . . . . . . . . . . . . . .99 Table A-14 Startup Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 Table A-15 Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 Table A-16 PLL Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Table A-17 MSCAN Wake-up Pulse Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Table A-18 SPI Master Mode Timing Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Table A-19 SPI Slave Mode Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Table A-20 Expanded Bus Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
14
MC9S12DJ64 Device User Guide -- V01.10
Derivative Differences and Document References
Derivative Differences
Table 0-1 shows the availability of peripheral modules on the various derivatives. For details about the compatibility within the MC9S12D-Family refer also to engineering bulletin EB386. Table 0-1 Derivative Differences
Generic device
CAN0 J1850/BDLC Packages Mask Set Temp Options Package Codes Note
MC9S12DJ64
1 1 112LQFP, 80QFP L86D M, V, C PV, FU An errata exists contact Sales office
MC9S12D64
1 0 112LQFP, 80QFP L86D M, V, C PV, FU An errata exists contact Sales office
MC9S12A64
0 0 112LQFP, 80QFP L86D C PV, FU An errata exists contact Sales office
MC9S12 DJ64 C FU
Package Option Temperature Option Device Title Controller Family
Temperature Options C = -40C to 85C V = -40C to 105C M = -40C to 125C Package Options FU = 80QFP PV = 112LQFP
Figure 0-1 Order Partnumber Example The following items should be considered when using a derivative. * Registers - - * Do not write or read CAN0 registers (after reset: address range $0140 - $017F), if using a derivative without CAN0 (see Table 0-1). Do not write or read BDLC registers (after reset: address range $00E8 - $00EF), if using a derivative without BDLC (see Table 0-1). Fill the four CAN0 interrupt vectors ($FFB0 - $FFB7) according to your coding policies for unused interrupts, if using a derivative without CAN0 (see Table 0-1). Fill the BDLC interrupt vector ($FFC2, $FFC3) according to your coding policies for unused interrupts, if using a derivative without BDLC (see Table 0-1).
Interrupts - -
*
Ports
15
MC9S12DJ64 Device User Guide -- V01.10
- - - *
The CAN0 pin functionality (TXCAN0, RXCAN0) is not available on port PJ7, PJ6, PM5, PM4, PM3, PM2, PM1 and PM0, if using a derivative without CAN0 (see Table 0-1). The BDLC pin functionality (TXB, RXB) is not available on port PM1 and PM0, if using a derivative without BDLC (see Table 0-1). Do not write MODRR1 and MODRR0 Bit of Module Routing Register (PIM_9DJ64 Block User Guide), if using a derivative without CAN0 (see Table 0-1). Port H In order to avoid floating nodes the ports should be either configured as outputs by setting the data direction register (DDRH at Base+$0262) to $FF, or enabling the pull resistors by writing a $FF to the pull enable register (PERH at Base+$0264). Port J[1:0] Port J pull-up resistors are enabled out of reset on all four pins (7:6 and 1:0). Therefore care must be taken not to disable the pull enables on PJ[1:0] by clearing the bits PERJ1 and PERJ0 at Base+$026C. Port K Port K pull-up resistors are enabled out of reset, i.e. Bit 7 = PUKE = 1 in the register PUCR at Base+$000C. Therefor care must be taken not to clear this bit. Port M[7:6] PM7:6 must be configured as outputs or their pull resistors must be enabled to avoid floating inputs. Port P6 PP6 must be configured as output or its pull resistor must be enabled to avoid a floating input. Port S[7:4] PS7:4 must be configured as outputs or their pull resistors must be enabled to avoid floating inputs. PAD[15:8] (ATD1 channels) Out of reset the ATD1 is disabled preventing current flows in the pins. Do not modify the ATD1 registers!
Pins not available in 80 pin QFP package -
-
-
-
- -
-
Document References
The Device User Guide provides information about the MC9S12DJ64 device made up of standard HCS12 blocks and the HCS12 processor core. This document is part of the customer documentation. A complete set of device manuals also includes the HCS12 Core User Guide and all the individual Block User Guides of the implemented modules. In a effort to reduce redundancy all module specific information is located only in the respective Block User Guide. If applicable, special implementation details of the module are given in the block description sections of this document. See Table 0-2 for names and versions of the referenced documents throughout the Device User Guide.
16
MC9S12DJ64 Device User Guide -- V01.10
Table 0-2 Document References
User Guide
HCS12 V1.5 Core User Guide Clock and Reset Generator (CRG) Block User Guide Oscillator (OSC) Block User Guide Enhanced Capture Timer 16 Bit 8 Channel (ECT_16B8C) Block User Guide Analog to Digital Converter 10 Bit 8 Channel (ATD_10B8C) Block User Guide Inter IC Bus (IIC) Block User Guide Asynchronous Serial Interface (SCI) Block User Guide Serial Peripheral Interface (SPI) Block User Guide Pulse Width Modulator 8 Bit 8 Channel (PWM_8B8C) Block User Guide 64K Byte Flash (FTS64K) Block User Guide 1K Byte EEPROM (EETS1K) Block User Guide Byte Level Data Link Controller -J1850 (BDLC) Block User Guide Motorola Scalable CAN (MSCAN) Block User Guide Voltage Regulator (VREG) Block User Guide Port Integration Module (PIM_9DJ64) Block User Guide
Versi on
1.2 V04 V02 V01 V02 V02 V02 V02 V01 V01 V01 V01 V02 V01 V01
Document Order Number
HCS12COREUG S12CRGV4/D S12OSCV2/D S12ECT16B8CV1/D S12ATD10B8CV2/D S12IICV2/D S12SCIV2/D S12SPIV2/D S12PWM8B8CV1/D S12FTS64KV1/D S12EETS1KV1/D S12BDLCV1/D S12MSCANV2/D S12VREGV1/D S12PIM9DJ64V1/D
17
MC9S12DJ64 Device User Guide -- V01.10
18
MC9S12DJ64 Device User Guide -- V01.10
Section 1 Introduction
1.1 Overview
The MC9S12DJ64 microcontroller unit (MCU) is a 16-bit device composed of standard on-chip peripherals including a 16-bit central processing unit (HCS12 CPU), 64K bytes of Flash EEPROM, 4K bytes of RAM, 1K bytes of EEPROM, two asynchronous serial communications interfaces (SCI), one serial peripheral interfaces (SPI), an 8-channel IC/OC enhanced capture timer, two 8-channel, 10-bit analog-to-digital converters (ADC), an 8-channel pulse-width modulator (PWM), a digital Byte Data Link Controller (BDLC), 29 discrete digital I/O channels (Port A, Port B, Port K and Port E), 20 discrete digital I/O lines with interrupt and wakeup capability, a CAN 2.0 A, B software compatible modules (MSCAN12), and an Inter-IC Bus. The MC9S12DJ64 has full 16-bit data paths throughout. However, the external bus can operate in an 8-bit narrow mode so single 8-bit wide memory can be interfaced for lower cost systems. The inclusion of a PLL circuit allows power consumption and performance to be adjusted to suit operational requirements.
1.2 Features
* HCS12 Core - 16-bit HCS12 CPU i. Upward compatible with M68HC11 instruction set ii. Interrupt stacking and programmer's model identical to M68HC11 iii. Instruction queue iv. Enhanced indexed addressing - - - - - * * MEBI (Multiplexed External Bus Interface) MMC (Module Mapping Control) INT (Interrupt control) BKP (Breakpoints) BDM (Background Debug Mode)
CRG (low current Colpitts or Pierce oscillator, PLL, reset, clocks, COP watchdog, real time interrupt, clock monitor) 8-bit and 4-bit ports with interrupt functionality - - Digital filtering Programmable rising or falling edge trigger 64K Flash EEPROM 1K byte EEPROM
*
Memory - -
19
MC9S12DJ64 Device User Guide -- V01.10
- * - - * - - - - - * - - - * - - - - - - - * - - * - *
4K byte RAM 10-bit resolution External conversion trigger capability Five receive and three transmit buffers Flexible identifier filter programmable as 2 x 32 bit, 4 x 16 bit or 8 x 8 bit Four separate interrupt channels for Rx, Tx, error and wake-up Low-pass filter wake-up function Loop-back for self test operation 16-bit main counter with 7-bit prescaler 8 programmable input capture or output compare channels Two 8-bit or one 16-bit pulse accumulators Programmable period and duty cycle 8-bit 8-channel or 16-bit 4-channel Separate control for each pulse width and duty cycle Center-aligned or left-aligned outputs Programmable clock select logic with a wide range of frequencies Fast emergency shutdown input Usable as interrupt inputs Two asynchronous Serial Communications Interfaces (SCI) Synchronous Serial Peripheral Interface (SPI) SAE J1850 Class B Data Communications Network Interface Compatible and ISO Compatible for Low-Speed (<125 Kbps) Serial Data Communications in Automotive Applications Compatible with I2C Bus standard Multi-master operation Software programmable for one of 256 different serial clock frequencies
Two 8-channel Analog-to-Digital Converters
1M bit per second, CAN 2.0 A, B software compatible module
Enhanced Capture Timer
8 PWM channels
Serial interfaces
Byte Data Link Controller (BDLC)
Inter-IC Bus (IIC) - - -
*
112-Pin LQFP or 80 QFP package
20
MC9S12DJ64 Device User Guide -- V01.10
- - - - - -
I/O lines with 5V input and drive capability 5V A/D converter inputs Operation at 50MHz equivalent to 25MHz Bus Speed Development support Single-wire background debugTM mode (BDM) On-chip hardware breakpoints
1.3 Modes of Operation
User modes * Normal and Emulation Operating Modes - - - - - * - - - Normal Single-Chip Mode Normal Expanded Wide Mode Normal Expanded Narrow Mode Emulation Expanded Wide Mode Emulation Expanded Narrow Mode Special Single-Chip Mode with active Background Debug Mode Special Test Mode (Motorola use only) Special Peripheral Mode (Motorola use only)
Special Operating Modes
Low power modes * * * Stop Mode Pseudo Stop Mode Wait Mode
21
MC9S12DJ64 Device User Guide -- V01.10
1.4 Block Diagram
Figure 1-1 shows a block diagram of the MC9S12DJ64 device.
22
MC9S12DJ64 Device User Guide -- V01.10
Figure 1-1 MC9S12DJ64 Block Diagram
64K Byte Flash EEPROM 4K Byte RAM 1K Byte EEPROM
VDDR VSSR VREGEN VDD1,2 VSS1,2 BKGD XFC VDDPLL VSSPLL EXTAL XTAL RESET PE0 PE1 PE2 PE3 PE4 PE5 PE6 PE7 TEST AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7
ATD0
VRH VRL VDDA VSSA PAD00 PAD01 PAD02 PAD03 PAD04 PAD05 PAD06 PAD07
ATD1
VRH VRL VDDA VSSA
VRH VRL VDDA VSSA PAD08 PAD09 PAD10 PAD11 PAD12 PAD13 PAD14 PAD15 PK0 PK1 PK2 PK3 PK4 PK5 PK7 PT0 PT1 PT2 PT3 PT4 PT5 PT6 PT7 PS0 PS1 PS2 PS3 PS4 PS5 PS6 PS7 PM0 PM1 PM2 PM3 PM4 PM5 PM6 PM7 XADDR14 XADDR15 XADDR16 XADDR17 XADDR18 XADDR19
Voltage Regulator
AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 PIX0 PIX1 PIX2 PIX3 PIX4 PIX5 ECS IOC0 IOC1 IOC2 IOC3 IOC4 IOC5 IOC6 IOC7 RXD TXD RXD TXD
AD0
Single-wire Background Debug Module
Clock and Reset Generation Module
CPU12
DDRK
PPAGE
PLL
Periodic Interrupt COP Watchdog Clock Monitor Breakpoints
PTK
AD1
ECS
XIRQ IRQ System R/W Integration LSTRB Module ECLK (SIM) MODA MODB NOACC/XCLKS
DDRE
PTE
Enhanced Capture Timer
DDRT DDRS
SCI0
PTS
SCI1 Multiplexed Address/Data Bus SPI0 DDRA PTA
DATA15 ADDR15 PA7 DATA14 ADDR14 PA6 DATA13 ADDR13 PA5 DATA12 ADDR12 PA4 DATA11 ADDR11 PA3 DATA10 ADDR10 PA2 DATA9 ADDR9 PA1 DATA8 ADDR8 PA0 MISO MOSI SCK SS
PTT
DDRB PTB
PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0
Module to Port Routing
BDLC (J1850)
DDRM
RXB TXB RXCAN CAN0 TXCAN
Multiplexed Wide Bus
IIC
SDA SCL PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7
Internal Logic 2.5V
VDD1,2 VSS1,2
I/O Driver 5V
VDDX VSSX
PTJ
Multiplexed Narrow Bus
KWJ0 KWJ1 KWJ6 KWJ7 KWP0 KWP1 KWP2 KWP3 KWP4 KWP5 KWP6 KWP7 KWH0 KWH1 KWH2 KWH3 KWH4 KWH5 KWH6 KWH7
PJ0 PJ1 PJ6 PJ7 PP0 PP1 PP2 PP3 PP4 PP5 PP6 PP7 PH0 PH1
DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0
DDRP
DDRJ
PLL 2.5V
VDDPLL VSSPLL
A/D Converter 5V & Voltage Regulator Reference
VDDA VSSA
PWM
Voltage Regulator 5V & I/O
VDDR VSSR
PTP
DDRH
PH2
PTH
PH3 PH4 PH5 PH6 PH7
Signals shown in Bold are not available on the 80 Pin Package
DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0
ADDR7 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0
PTM
23
MC9S12DJ64 Device User Guide -- V01.10
24
MC9S12DJ64 Device User Guide -- V01.10
1.5 Device Memory Map
Table 1-1 and Figure 1-2 show the device memory map of the MC9S12DJ64 after reset. The 1K EEPROM is mapped twice in a 2K address space. Note that after reset the bottom 1k of the EEPROM ($0000 - $03FF) are hidden by the register space, and the 1K $0400 - $07FF is hidden by the RAM. Table 1-1 Device Memory Map
Address
$0000 - $0017 $0018 - $0019 Reserved
Module
CORE (Ports A, B, E, Modes, Inits, Test)
Size (Bytes)
24 2 2 4 8 8 4 12 64 32 40 8 8 8 8 8 16 16 12 4 32 64 192 64 384 2048 4096 16384 16384 16384
$001A - $001B Device ID register (PARTID) $001C - $001F CORE (MEMSIZ, IRQ, HPRIO) $0020 - $0027 $0028 - $002F $0030 - $0033 $0034 - $003F $0040 - $007F $0080 - $009F Reserved CORE (Background Debug Mode) CORE (PPAGE, Port K) Clock and Reset Generator (PLL, RTI, COP) Enhanced Capture Timer 16-bit 8 channels Analog to Digital Converter 10-bit 8 channels (ATD0)
$00A0 - $00C7 Pulse Width Modulator 8-bit 8 channels (PWM) $00C8 - $00CF Serial Communications Interface 0 (SCI0) $00D0 - $00D7 Serial Communications Interface 0 (SCI1) $00D8 - $00DF Serial Peripheral Interface (SPI0) $00E0 - $00E7 Inter IC Bus $00E8 - $00EF Byte Data Link Controller (BDLC) $00F0 - $00FF $0100- $010F $0110 - $011B $0120 - $013F $0140 - $017F $0180 - $023F $0240 - $027F $0280 - $03FF $0000 - $07FF $0000 - $0FFF $4000 - $7FFF Reserved Flash Control Register EEPROM Control Register Analog to Digital Converter 10-bit 8 channels (ATD1) Motorola Scalable Can (CAN0) Reserved Port Integration Module (PIM) Reserved EEPROM array 1k Array mapped twice in the address space RAM array Fixed Flash EEPROM array incl. 0.5K, 1K, 2K or 4K Protected Sector at start
$011C - $011F Reserved
$8000 - $BFFF Flash EEPROM Page Window Fixed Flash EEPROM array $C000 - $FFFF incl. 0.5K, 1K, 2K or 4K Protected Sector at end and 256 bytes of Vector Space at $FF80 - $FFFF
25
MC9S12DJ64 Device User Guide -- V01.10
Figure 1-2 MC9S12DJ64 Memory Map out of Reset
$0000 $0400
$03FF $0000
REGISTERS
(Mappable to any 2K Boundary within the first 32K)
$0800
$0000
1K Bytes EEPROM
(Mappable to any 2K Boundary; 1K mapped two times in the 2K address space)
$07FF
$1000
$0000
4K Bytes RAM
(Mappable to any 4K Boundary)
EXTERN
EXTERN
$0FFF
$4000
$4000
16K Fixed Flash Page $3E = 62
(This is dependant on the state of the ROMHM bit)
$7FFF
$8000
$8000
EXTERN
$BFFF
16K Page Window 4 x 16K Flash EEPROM pages
$C000
$C000
16K Fixed Flash Page $3F = 63
$FFFF $FF00
$FF00 VECTORS $FFFF EXPANDED NORMAL SINGLE CHIP SPECIAL SINGLE CHIP VECTORS VECTORS
$FFFF
BDM (if active)
26
MC9S12DJ64 Device User Guide -- V01.10
1.5.1 Detailed Register Map
$0000 - $000F
Address $0000 $0001 $0002 $0003 $0004 $0005 $0006 $0007 $0008 $0009 $000A $000B $000C $000D $000E $000F Name PORTA PORTB DDRA DDRB Reserved Reserved Reserved Reserved PORTE DDRE PEAR MODE PUCR RDRIV EBICTL Reserved
MEBI map 1 of 3 (Core User Guide)
Bit 7 Read: Bit 7 Write: Read: Bit 7 Write: Read: Bit 7 Write: Read: Bit 7 Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Read: Bit 7 Write: Read: Bit 7 Write: Read: NOACCE Write: Read: MODC Write: Read: PUPKE Write: Read: RDPK Write: Read: 0 Write: Read: 0 Write: Bit 6 6 6 6 6 0 0 0 0 6 6 0 MODB 0 0 0 0 Bit 5 5 5 5 5 0 0 0 0 5 5 PIPOE MODA 0 0 0 0 Bit 4 4 4 4 4 0 0 0 0 4 4 NECLK 0 PUPEE RDPE 0 0 Bit 3 3 3 3 3 0 0 0 0 3 3 LSTRE IVIS 0 0 0 0 Bit 2 2 2 2 2 0 0 0 0 2 Bit 2 RDWE 0 0 0 0 0 Bit 1 1 1 1 1 0 0 0 0 Bit 1 0 0 EMK PUPBE RDPB 0 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 0 0 0 0 Bit 0 0 0 EME PUPAE RDPA ESTR 0
$0010 - $0014
Address $0010 $0011 $0012 $0013 $0014 Name INITRM INITRG INITEE MISC MTST0 Test Only
MMC map 1 of 4 (Core User Guide)
Bit 7 Read: RAM15 Write: Read: 0 Write: Read: EE15 Write: Read: 0 Write: Read: Bit 7 Write: Bit 6 RAM14 REG14 EE14 0 6 Bit 5 RAM13 REG13 EE13 0 5 Bit 4 RAM12 REG12 EE12 0 4 Bit 3 RAM11 REG11 0 Bit 2 0 0 0 Bit 1 0 0 0 Bit 0 RAMHAL 0 EEON
EXSTR1 EXSTR0 ROMHM ROMON 3 2 1 Bit 0
27
MC9S12DJ64 Device User Guide -- V01.10
$0015 - $0016
Address $0015 $0016 Name ITCR ITEST Read: Write: Read: Write:
INT map 1 of 2 (Core User Guide)
Bit 7 0 INTE Bit 6 0 INTC Bit 5 0 INTA Bit 4 WRINT INT8 Bit 3 ADR3 INT6 Bit 2 ADR2 INT4 Bit 1 ADR1 INT2 Bit 0 ADR0 INT0
$0017 - $0017
Address $0017 Name MTST1 Test Only Read: Write:
MMC map 2 of 4 (Core User Guide)
Bit 7 Bit 7 Bit 6 6 Bit 5 5 Bit 4 4 Bit 3 3 Bit 2 2 Bit 1 1 Bit 0 Bit 0
$0018 - $001B
Address $0018 $0019 $001A $001B Name Reserved Reserved PARTIDH PARTIDL Read: Write: Read: Write: Read: Write: Read: Write:
Miscellaneous Peripherals (Device User Guide, Table 1-3)
Bit 7 0 0 ID15 ID7 Bit 6 0 0 ID14 ID6 Bit 5 0 0 ID13 ID5 Bit 4 0 0 ID12 ID4 Bit 3 0 0 ID11 ID3 Bit 2 0 0 ID10 ID2 Bit 1 0 0 ID9 ID1 Bit 0 0 0 ID8 ID0
$001C - $001D
Address $001C $001D Name MEMSIZ0 MEMSIZ1
MMC map 3 of 4 (Core and Device User Guide, Table 1-4)
Bit 7 Bit 6 Bit 5 Bit 4 Read: reg_sw0 0 eep_sw1 eep_sw0 Write: Read: rom_sw1 rom_sw0 0 0 Write: Bit 3 0 0 Bit 2 Bit 1 Bit 0 ram_sw2 ram_sw1 ram_sw0 0 pag_sw1 pag_sw0
$001E - $001E
Address $001E Name INTCR Read: Write:
MEBI map 2 of 3 (Core User Guide)
Bit 7 IRQE Bit 6 IRQEN Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 0 Bit 1 0 Bit 0 0
$001F - $001F
Address $001F Name HPRIO Read: Write:
INT map 2 of 2 (Core User Guide)
Bit 7 PSEL7 Bit 6 PSEL6 Bit 5 PSEL5 Bit 4 PSEL4 Bit 3 PSEL3 Bit 2 PSEL2 Bit 1 PSEL1 Bit 0 0
28
MC9S12DJ64 Device User Guide -- V01.10
$0020 - $0027
Address $0020 $0027 Name Reserved Read: Write:
Reserved
Bit 7 0 Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 0 Bit 1 0 Bit 0 0
$0028 - $002F
Address $0028 $0029 $002A $002B $002C $002D $002E $002F Name BKPCT0 BKPCT1 BKP0X BKP0H BKP0L BKP1X BKP1H BKP1L
BKP (Core User Guide)
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Read: 0 0 0 0 BKEN BKFULL BKBDM BKTAG Write: Read: BK0MBH BK0MBL BK1MBH BK1MBL BK0RWE BK0RW BK1RWE BK1RW Write: Read: 0 0 BK0V5 BK0V4 BK0V3 BK0V2 BK0V1 BK0V0 Write: Read: Bit 15 14 13 12 11 10 9 Bit 8 Write: Read: Bit 7 6 5 4 3 2 1 Bit 0 Write: Read: 0 0 BK1V5 BK1V4 BK1V3 BK1V2 BK1V1 BK1V0 Write: Read: Bit 15 14 13 12 11 10 9 Bit 8 Write: Read: Bit 7 6 5 4 3 2 1 Bit 0 Write:
$0030 - $0031
Address $0030 $0031 Name PPAGE Reserved Read: Write: Read: Write:
MMC map 4 of 4 (Core User Guide)
Bit 7 0 0 Bit 6 0 0 Bit 5 PIX5 0 Bit 4 PIX4 0 Bit 3 PIX3 0 Bit 2 PIX2 0 Bit 1 PIX1 0 Bit 0 PIX0 0
$0032 - $0033
Address $0032 $0033 Name PORTK DDRK Read: Write: Read: Write:
MEBI map 3 of 3 (Core User Guide)
Bit 7 Bit 7 Bit 7 Bit 6 6 6 Bit 5 5 5 Bit 4 4 4 Bit 3 3 3 Bit 2 2 2 Bit 1 1 1 Bit 0 Bit 0 Bit 0
29
MC9S12DJ64 Device User Guide -- V01.10
$0034 - $003F
Address $0034 $0035 $0036 $0037 $0038 $0039 $003A $003B $003C $003D $003E $003F Name SYNR REFDV CTFLG TEST ONLY CRGFLG CRGINT CLKSEL PLLCTL RTICTL COPCTL FORBYP TEST ONLY CTCTL TEST ONLY ARMCOP
CRG (Clock and Reset Generator)
Bit 7 Read: 0 Write: Read: 0 Write: Read: 0 Write: Read: RTIF Write: Read: RTIE Write: Read: PLLSEL Write: Read: CME Write: Read: 0 Write: Read: WCOP Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Bit 7 Bit 6 0 0 0 PORF 0 PSTP PLLON RTR6 RSBCK 0 0 0 6 Bit 5 SYN5 0 0 0 0 Bit 4 SYN4 0 0 LOCKIF LOCKIE Bit 3 SYN3 Bit 2 SYN2 Bit 1 SYN1 Bit 0 SYN0
REFDV3 REFDV2 REFDV1 REFDV0 0 LOCK 0 PLLWAI 0 RTR3 0 0 0 0 3 0 TRACK 0 CWAI PRE RTR2 CR2 0 0 0 2 0 SCMIF SCMIE RTIWAI PCE RTR1 CR1 0 0 0 1 0 SCM 0 COPWAI SCME RTR0 CR0 0 0 0 Bit 0
SYSWAI ROAWAI AUTO RTR5 0 0 0 0 5 ACQ RTR4 0 0 0 0 4
$0040 - $007F
Address $0040 $0041 $0042 $0043 $0044 $0045 $0046 $0047 $0048 $0049 Name TIOS CFORC OC7M OC7D TCNT (hi) TCNT (lo) TSCR1 TTOV TCTL1 TCTL2
ECT (Enhanced Capture Timer 16 Bit 8 Channels)
Bit 7 Read: IOS7 Write: Read: 0 Write: FOC7 Read: OC7M7 Write: Read: OC7D7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: TEN Write: Read: TOV7 Write: Read: OM7 Write: Read: OM3 Write: Bit 6 IOS6 0 FOC6 OC7M6 OC7D6 14 6 TSWAI TOV6 OL7 OL3 Bit 5 IOS5 0 FOC5 OC7M5 OC7D5 13 5 TSFRZ TOV5 OM6 OM2 Bit 4 IOS4 0 FOC4 OC7M4 OC7D4 12 4 TFFCA TOV4 OL6 OL2 Bit 3 IOS3 0 FOC3 OC7M3 OC7D3 11 3 0 TOV3 OM5 OM1 Bit 2 IOS2 0 FOC2 OC7M2 OC7D2 10 2 0 TOV2 OL5 OL1 Bit 1 IOS1 0 FOC1 OC7M1 OC7D1 9 1 0 TOV1 OM4 OM0 Bit 0 IOS0 0 FOC0 OC7M0 OC7D0 Bit 8 Bit 0 0 TOV0 OL4 OL0
30
MC9S12DJ64 Device User Guide -- V01.10
$0040 - $007F
Address $004A $004B $004C $004D $004E $004F $0050 $0051 $0052 $0053 $0054 $0055 $0056 $0057 $0058 $0059 $005A $005B $005C $005D $005E $005F $0060 $0061 $0062 Name TCTL3 TCTL4 TIE TSCR2 TFLG1 TFLG2 TC0 (hi) TC0 (lo) TC1 (hi) TC1 (lo) TC2 (hi) TC2 (lo) TC3 (hi) TC3 (lo) TC4 (hi) TC4 (lo) TC5 (hi) TC5 (lo) TC6 (hi) TC6 (lo) TC7 (hi) TC7 (lo) PACTL PAFLG PACN3 (hi)
ECT (Enhanced Capture Timer 16 Bit 8 Channels)
Bit 7 Read: EDG7B Write: Read: EDG3B Write: Read: C7I Write: Read: TOI Write: Read: C7F Write: Read: TOF Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: 0 Write: Read: 0 Write: Read: Bit 7 Write: Bit 6 EDG7A EDG3A C6I 0 C6F 0 14 6 14 6 14 6 14 6 14 6 14 6 14 6 14 6 PAEN 0 6 Bit 5 EDG6B EDG2B C5I 0 C5F 0 13 5 13 5 13 5 13 5 13 5 13 5 13 5 13 5 PAMOD 0 5 Bit 4 EDG6A EDG2A C4I 0 C4F 0 12 4 12 4 12 4 12 4 12 4 12 4 12 4 12 4 PEDGE 0 4 Bit 3 EDG5B EDG1B C3I TCRE C3F 0 11 3 11 3 11 3 11 3 11 3 11 3 11 3 11 3 CLK1 0 3 Bit 2 EDG5A EDG1A C2I PR2 C2F 0 10 2 10 2 10 2 10 2 10 2 10 2 10 2 10 2 CLK0 0 2 Bit 1 EDG4B EDG0B C1I PR1 C1F 0 9 1 9 1 9 1 9 1 9 1 9 1 9 1 9 1 PAOVI PAOVF 1 Bit 0 EDG4A EDG0A C0I PR0 C0F 0 Bit 8 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 PAI PAIF Bit 0
31
MC9S12DJ64 Device User Guide -- V01.10
$0040 - $007F
Address $0063 $0064 $0065 $0066 $0067 $0068 $0069 $006A $006B $006C $006D $006E $006F $0070 $0071 $0072 $0073 $0074 $0075 $0076 $0077 $0078 $0079 $007A $007B Name PACN2 (lo) PACN1 (hi) PACN0 (lo) MCCTL MCFLG ICPAR DLYCT ICOVW ICSYS Reserved TIMTST Test Only Reserved Reserved PBCTL PBFLG PA3H PA2H PA1H PA0H MCCNT (hi) MCCNT (lo) TC0H (hi) TC0H (lo) TC1H (hi) TC1H (lo)
ECT (Enhanced Capture Timer 16 Bit 8 Channels)
Bit 7 Read: Bit 7 Write: Read: Bit 7 Write: Read: Bit 7 Write: Read: MCZI Write: Read: MCZF Write: Read: 0 Write: Read: 0 Write: Read: NOVW7 Write: Read: SH37 Write: Read: Write: Read: 0 Write: Read: Write: Read: Write: Read: 0 Write: Read: 0 Write: Read: Bit 7 Write: Read: Bit 7 Write: Read: Bit 7 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Read: Bit 15 Write: Read: Bit 7 Write: Bit 6 6 6 6 MODMC 0 0 0 NOVW6 SH26 Bit 5 5 5 5 RDMCL 0 0 0 NOVW5 SH15 Bit 4 4 4 4 0 ICLAT 0 0 0 NOVW4 SH04 Bit 3 3 3 3 0 FLMC POLF3 PA3EN 0 NOVW3 TFMOD Bit 2 2 2 2 MCEN POLF2 PA2EN 0 NOVW2 PACMX Bit 1 1 1 1 MCPR1 POLF1 PA1EN DLY1 NOVW1 BUFEN Bit 0 Bit 0 Bit 0 Bit 0 MCPR0 POLF0 PA0EN DLY0 NOVW0 LATQ
0
0
0
0
0
TCBYP
0
PBEN 0 6 6 6 6 14 6 14 6 14 6
0 0 5 5 5 5 13 5 13 5 13 5
0 0 4 4 4 4 12 4 12 4 12 4
0 0 3 3 3 3 11 3 11 3 11 3
0 0 2 2 2 2 10 2 10 2 10 2
PBOVI PBOVF 1 1 1 1 9 1 9 1 9 1
0 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0
32
MC9S12DJ64 Device User Guide -- V01.10
$0040 - $007F
Address $007C $007D $007E $007F Name TC2H (hi) TC2H (lo) TC3H (hi) TC3H (lo) Read: Write: Read: Write: Read: Write: Read: Write:
ECT (Enhanced Capture Timer 16 Bit 8 Channels)
Bit 7 Bit 15 Bit 7 Bit 15 Bit 7 Bit 6 14 6 14 6 Bit 5 13 5 13 5 Bit 4 12 4 12 4 Bit 3 11 3 11 3 Bit 2 10 2 10 2 Bit 1 9 1 9 1 Bit 0 Bit 8 Bit 0 Bit 8 Bit 0
$0080 - $009F
Address $0080 $0081 $0082 $0083 $0084 $0085 $0086 $0087 $0088 $0089 $008A $008B $008C $008D $008E $008F $0090 $0091 $0092 Name ATD0CTL0 ATD0CTL1 ATD0CTL2 ATD0CTL3 ATD0CTL4 ATD0CTL5 ATD0STAT0 Reserved ATD0TEST0 ATD0TEST1 Reserved ATD0STAT1 Reserved ATD0DIEN Reserved PORTAD0 ATD0DR0H ATD0DR0L ATD0DR1H
ATD0 (Analog to Digital Converter 10 Bit 8 Channel)
Bit 7 Read: 0 Write: Read: 0 Write: Read: ADPU Write: Read: 0 Write: Read: SRES8 Write: Read: DJM Write: Read: SCF Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Read: CCF7 Write: Read: 0 Write: Read: Bit 7 Write: Read: 0 Write: Read: Bit7 Write: Read: Bit15 Write: Read: Bit7 Write: Read: Bit15 Write: Bit 6 0 0 AFFC S8C SMP1 DSGN 0 0 0 0 0 CCF6 0 6 0 6 14 Bit6 14 Bit 5 0 0 AWAI S4C SMP0 SCAN ETORF 0 0 0 0 CCF5 0 5 0 5 13 0 13 Bit 4 0 0 Bit 3 0 0 Bit 2 0 0 ETRIG FIFO PRS2 CC CC2 0 0 0 0 CCF2 0 2 0 2 10 0 10 Bit 1 0 0 ASCIE FRZ1 PRS1 CB CC1 0 0 0 0 CCF1 0 1 0 1 9 0 9 Bit 0 0 0 ASCIF FRZ0 PRS0 CA CC0 0 0 SC 0 CCF0 0 Bit 0 0 BIT 0 Bit8 0 Bit8
ETRIGLE ETRIGP S2C PRS4 MULT FIFOR 0 0 0 0 CCF4 0 4 0 4 12 0 12 S1C PRS3 0 0 0 0 0 0 CCF3 0 3 0 3 11 0 11
33
MC9S12DJ64 Device User Guide -- V01.10
$0080 - $009F
Address $0093 $0094 $0095 $0096 $0097 $0098 $0099 $009A $009B $009C $009D $009E $009F Name ATD0DR1L ATD0DR2H ATD0DR2L ATD0DR3H ATD0DR3L ATD0DR4H ATD0DR4L ATD0DR5H ATD0DR5L ATD0DR6H ATD0DR6L ATD0DR7H ATD0DR7L Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write:
ATD0 (Analog to Digital Converter 10 Bit 8 Channel)
Bit 7 Bit7 Bit15 Bit7 Bit15 Bit7 Bit15 Bit7 Bit15 Bit7 Bit15 Bit7 Bit15 Bit7 Bit 6 Bit6 14 Bit6 14 Bit6 14 Bit6 14 Bit6 14 Bit6 14 Bit6 Bit 5 0 13 0 13 0 13 0 13 0 13 0 13 0 Bit 4 0 12 0 12 0 12 0 12 0 12 0 12 0 Bit 3 0 11 0 11 0 11 0 11 0 11 0 11 0 Bit 2 0 10 0 10 0 10 0 10 0 10 0 10 0 Bit 1 0 9 0 9 0 9 0 9 0 9 0 9 0 Bit 0 0 Bit8 0 Bit8 0 Bit8 0 Bit8 0 Bit8 0 Bit8 0
$00A0 - $00C7
Address $00A0 $00A1 $00A2 $00A3 $00A4 $00A5 $00A6 $00A7 $00A8 Name PWME PWMPOL PWMCLK PWMPRCLK PWMCAE PWMCTL PWMTST Test Only PWMPRSC Test Only PWMSCLA
PWM (Pulse Width Modulator 8 Bit 8 Channel)
Bit 7 Read: PWME7 Write: Read: PPOL7 Write: Read: PCLK7 Write: Read: 0 Write: Read: CAE7 Write: Read: CON67 Write: Read: 0 Write: Read: 0 Write: Read: Bit 7 Write: Bit 6 PWME6 PPOL6 PCLK6 PCKB2 CAE6 CON45 0 0 6 Bit 5 PWME5 PPOL5 PCLK5 PCKB1 CAE5 CON23 0 0 5 Bit 4 PWME4 PPOL4 PCLK4 PCKB0 CAE4 CON01 0 0 4 Bit 3 PWME3 PPOL3 PCLK3 0 CAE3 PSWAI 0 0 3 Bit 2 PWME2 PPOL2 PCLK2 PCKA2 CAE2 PFRZ 0 0 2 Bit 1 PWME1 PPOL1 PCLK1 PCKA1 CAE1 0 0 0 1 Bit 0 PWME0 PPOL0 PCLK0 PCKA0 CAE0 0 0 0 Bit 0
34
MC9S12DJ64 Device User Guide -- V01.10
$00A0 - $00C7
Address $00A9 $00AA $00AB $00AC $00AD $00AE $00AF $00B0 $00B1 $00B2 $00B3 $00B4 $00B5 $00B6 $00B7 $00B8 $00B9 $00BA $00BB $00BC $00BD $00BE $00BF $00C0 $00C1 Name Read: PWMSCLB Write: PWMSCNTA Read: Test Only Write: PWMSCNTB Read: Test Only Write: Read: PWMCNT0 Write: Read: PWMCNT1 Write: Read: PWMCNT2 Write: Read: PWMCNT3 Write: Read: PWMCNT4 Write: Read: PWMCNT5 Write: Read: PWMCNT6 Write: Read: PWMCNT7 Write: Read: PWMPER0 Write: Read: PWMPER1 Write: Read: PWMPER2 Write: Read: PWMPER3 Write: Read: PWMPER4 Write: Read: PWMPER5 Write: Read: PWMPER6 Write: Read: PWMPER7 Write: Read: PWMDTY0 Write: Read: PWMDTY1 Write: Read: PWMDTY2 Write: Read: PWMDTY3 Write: Read: PWMDTY4 Write: Read: PWMDTY5 Write:
PWM (Pulse Width Modulator 8 Bit 8 Channel)
Bit 7 Bit 7 0 0 Bit 7 0 Bit 7 0 Bit 7 0 Bit 7 0 Bit 7 0 Bit 7 0 Bit 7 0 Bit 7 0 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 7 Bit 6 6 0 0 6 0 6 0 6 0 6 0 6 0 6 0 6 0 6 0 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Bit 5 5 0 0 5 0 5 0 5 0 5 0 5 0 5 0 5 0 5 0 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Bit 4 4 0 0 4 0 4 0 4 0 4 0 4 0 4 0 4 0 4 0 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Bit 3 3 0 0 3 0 3 0 3 0 3 0 3 0 3 0 3 0 3 0 3 3 3 3 3 3 3 3 3 3 3 3 3 3 Bit 2 2 0 0 2 0 2 0 2 0 2 0 2 0 2 0 2 0 2 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Bit 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Bit 0 Bit 0 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0 Bit 0
35
MC9S12DJ64 Device User Guide -- V01.10
$00A0 - $00C7
Address $00C2 $00C3 $00C4 $00C5 $00C6 $00C7 Name PWMDTY6 PWMDTY7 PWMSDN Reserved Reserved Reserved
PWM (Pulse Width Modulator 8 Bit 8 Channel)
Bit 7 Read: Bit 7 Write: Read: Bit 7 Write: Read: PWMIF Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Bit 6 6 6 PWMIE 0 0 0 Bit 5 5 5 Bit 4 4 4 Bit 3 3 3 0 0 0 0 Bit 2 2 2 PWM7IN 0 0 0 Bit 1 1 1 Bit 0 Bit 0 Bit 0
PWMRSTRT PWMLVL
PWM7INL PWM7ENA 0 0 0 0 0 0
0 0 0
0 0 0
$00C8 - $00CF
Address $00C8 $00C9 $00CA $00CB $00CC $00CD $00CE $00CF Name SCI0BDH SCI0BDL SCI0CR1 SCI0CR2 SCI0SR1 SCI0SR2 SCI0DRH SCI0DRL
SCI0 (Asynchronous Serial Interface)
Bit 7 Bit 6 Read: 0 0 Write: Read: SBR7 SBR6 Write: Read: LOOPS SCISWAI Write: Read: TIE TCIE Write: Read: TDRE TC Write: Read: 0 0 Write: Read: R8 T8 Write: Read: R7 R6 Write: T7 T6 Bit 5 0 SBR5 RSRC RIE RDRF 0 0 R5 T5 Bit 4 SBR12 SBR4 M ILIE IDLE 0 0 R4 T4 Bit 3 SBR11 SBR3 WAKE TE OR 0 0 R3 T3 Bit 2 SBR10 SBR2 ILT RE NF BRK13 0 R2 T2 Bit 1 SBR9 SBR1 PE RWU FE TXDIR 0 R1 T1 Bit 0 SBR8 SBR0 PT SBK PF RAF 0 R0 T0
$00D0 - $00D7
Address $00D0 $00D1 $00D2 $00D3 $00D4 Name SCI1BDH SCI1BDL SCI1CR1 SCI1CR2 SCI1SR1
SCI1 (Asynchronous Serial Interface)
Bit 7 Bit 6 Read: 0 0 Write: Read: SBR7 SBR6 Write: Read: LOOPS SCISWAI Write: Read: TIE TCIE Write: Read: TDRE TC Write: Bit 5 0 SBR5 RSRC RIE RDRF Bit 4 SBR12 SBR4 M ILIE IDLE Bit 3 SBR11 SBR3 WAKE TE OR Bit 2 SBR10 SBR2 ILT RE NF Bit 1 SBR9 SBR1 PE RWU FE Bit 0 SBR8 SBR0 PT SBK PF
36
MC9S12DJ64 Device User Guide -- V01.10
$00D0 - $00D7
Address $00D5 $00D6 $00D7 Name SCI1SR2 SCI1DRH SCI1DRL Read: Write: Read: Write: Read: Write:
SCI1 (Asynchronous Serial Interface)
Bit 7 0 R8 R7 T7 Bit 6 0 T8 R6 T6 Bit 5 0 0 R5 T5 Bit 4 0 0 R4 T4 Bit 3 0 0 R3 T3 Bit 2 BRK13 0 R2 T2 Bit 1 TXDIR 0 R1 T1 Bit 0 RAF 0 R0 T0
$00D8 - $00DF
Address $00D8 $00D9 $00DA $00DB $00DC $00DD $00DE $00DF Name SPI0CR1 SPI0CR2 SPI0BR SPI0SR Reserved SPI0DR Reserved Reserved Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write:
SPI0 (Serial Peripheral Interface)
Bit 7 SPIE 0 0 SPIF 0 Bit7 0 0 Bit 6 SPE 0 SPPR2 0 0 6 0 0 Bit 5 SPTIE 0 SPPR1 SPTEF 0 5 0 0 Bit 4 MSTR Bit 3 CPOL Bit 2 CPHA 0 SPR2 0 0 2 0 0 Bit 1 SSOE SPISWAI SPR1 0 0 1 0 0 Bit 0 LSBFE SPC0 SPR0 0 0 Bit0 0 0
MODFEN BIDIROE SPPR0 MODF 0 4 0 0 0 0 0 3 0 0
$00E0 - $00E7
Address $00E0 $00E1 $00E2 $00E3 $00E4 $00E5 $00E6 $00E7 Name IBAD IBFD IBCR IBSR IBDR Reserved Reserved Reserved Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write:
IIC (Inter IC Bus)
Bit 7 ADR7 IBC7 IBEN TCF D7 0 0 0 Bit 6 ADR6 IBC6 IBIE IAAS D6 0 0 0 Bit 5 ADR5 IBC5 MS/SL IBB D5 0 0 0 Bit 4 ADR4 IBC4 TX/RX IBAL D4 0 0 0 Bit 3 ADR3 IBC3 TXAK 0 D3 0 0 0 Bit 2 ADR2 IBC2 0 RSTA SRW D2 0 0 0 Bit 1 ADR1 IBC1 0 IBIF D1 0 0 0 Bit 0 0 IBC0 IBSWAI RXAK D0 0 0 0
37
MC9S12DJ64 Device User Guide -- V01.10
$00E8 - $00EF
Address $00E8 $00E9 $00EA $00EB $00EC $00ED $00EE $00EF Name DLCBCR1 DLCBSVR DLCBCR2 DLCBDR DLCBARD DLCBRSR DLCSCR DLCBSTAT
BDLC (Bytelevel Data Link Controller J1850)
Bit 7 Read: IMSG Write: Read: 0 Write: Read: SMRST Write: Read: D7 Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Bit 6 CLKS 0 DLOOP D6 RXPOL 0 0 0 Bit 5 0 I3 RX4XE D5 0 R5 0 0 Bit 4 0 I2 NBFS D4 0 R4 BDLCE 0 Bit 3 0 I1 TEOD D3 BO3 R3 0 0 Bit 2 0 I0 TSIFR D2 BO2 R2 0 0 Bit 1 IE 0 TMIFR1 D1 BO1 R1 0 0 Bit 0 WCM 0 TMIFR0 D0 BO0 R0 0 IDLE
$00F0 - $00FF
Address $00F0 $00FF Name Reserved Read: Write:
Reserved
Bit 7 0 Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 0 Bit 1 0 Bit 0 0
$0100 - $010F
Address $0100 $0101 $0102 $0103 $0104 $0105 $0106 $0107 $0108 $0109 Name FCLKDIV FSEC Reserved FCNFG FPROT FSTAT FCMD Reserved for Factory Test FADDRHI FADDRLO
Flash Control Register (fts64k)
Bit 7 Bit 6 Read: FDIVLD PRDIV8 Write: Read: KEYEN NV6 Write: Read: 0 0 Write: Read: CBEIE CCIE Write: Read: FPOPEN NV6 Write: Read: CCIF CBEIF Write: Read: 0 CMDB6 Write: Read: 0 0 Write: Read: 0 Bit 14 Write: Read: Bit 7 6 Write: Bit 5 FDIV5 NV5 0 KEYACC FPHDIS PVIOL CMDB5 0 13 5 Bit 4 FDIV4 NV4 0 0 FPHS1 ACCERR 0 0 12 4 Bit 3 FDIV3 NV3 0 0 FPHS0 0 0 0 11 3 Bit 2 FDIV2 NV2 0 0 FPLDIS BLANK CMDB2 0 10 2 Bit 1 FDIV1 SEC1 0 0 FPLS1 0 0 0 9 1 Bit 0 FDIV0 SEC0 0 0 FPLS0 0 CMDB0 0 Bit 8 Bit 0
38
MC9S12DJ64 Device User Guide -- V01.10
$0100 - $010F
Address $010A $010B $010C $010F Name FDATAHI FDATALO Reserved Read: Write: Read: Write: Read: Write:
Flash Control Register (fts64k)
Bit 7 Bit 15 Bit 7 0 Bit 6 14 6 0 Bit 5 13 5 0 Bit 4 12 4 0 Bit 3 11 3 0 Bit 2 10 2 0 Bit 1 9 1 0 Bit 0 Bit 8 Bit 0 0
$0110 - $011B
Address $0110 $0111 $0112 $0113 $0114 $0115 $0116 $0117 $0118 $0119 $011A $011B Name ECLKDIV Reserved Reserved for Factory Test ECNFG EPROT ESTAT ECMD Reserved for Factory Test EADDRHI EADDRLO EDATAHI EDATALO
EEPROM Control Register (eets1k)
Bit 7 Bit 6 Read: EDIVLD PRDIV8 Write: Read: 0 0 Write: Read: 0 0 Write: Read: CBEIE CCIE Write: Read: EPOPEN NV6 Write: Read: CCIF CBEIF Write: Read: 0 CMDB6 Write: Read: 0 0 Write: Read: 0 0 Write: Read: Bit 7 6 Write: Read: Bit 15 14 Write: Read: Bit 7 6 Write: Bit 5 EDIV5 0 0 0 NV5 PVIOL CMDB5 0 0 Bit 4 EDIV4 0 0 0 NV4 ACCERR 0 0 0 Bit 3 EDIV3 0 0 0 EPDIS 0 0 0 0 Bit 2 EDIV2 0 0 0 EP2 BLANK CMDB2 0 0 Bit 1 EDIV1 0 0 0 EP1 0 0 0 0 Bit 0 EDIV0 0 0 0 EP0 0 CMDB0 0 Bit 8 Bit 0 Bit 8 Bit 0
5 13 5
4 12 4
3 11 3
2 10 2
1 9 1
$011C - $011F
Address $011C $011F Name Reserved Read: Write:
Reserved for RAM Control Register
Bit 7 0 Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 0 Bit 1 0 Bit 0 0
39
MC9S12DJ64 Device User Guide -- V01.10
$0120 - $013F
Address $0120 $0121 $0122 $0123 $0124 $0125 $0126 $0127 $0128 $0129 $012A $012B $012C $012D $012E $012F $0130 $0131 $0132 $0133 $0134 $0135 $0136 $0137 $0138 Name ATD1CTL0 ATD1CTL1 ATD1CTL2 ATD1CTL3 ATD1CTL4 ATD1CTL5 ATD1STAT0 Reserved ATD1TEST0 ATD1TEST1 Reserved ATD1STAT1 Reserved ATD1DIEN Reserved PORTAD1 ATD1DR0H ATD1DR0L ATD1DR1H ATD1DR1L ATD1DR2H ATD1DR2L ATD1DR3H ATD1DR3L ATD1DR4H
ATD1 (Analog to Digital Converter 10 Bit 8 Channel)
Bit 7 Read: 0 Write: Read: 0 Write: Read: ADPU Write: Read: 0 Write: Read: SRES8 Write: Read: DJM Write: Read: SCF Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Read: 0 Write: Read: CCF7 Write: Read: 0 Write: Read: Bit 7 Write: Read: 0 Write: Read: Bit7 Write: Read: Bit15 Write: Read: Bit7 Write: Read: Bit15 Write: Read: Bit7 Write: Read: Bit15 Write: Read: Bit7 Write: Read: Bit15 Write: Read: Bit7 Write: Read: Bit15 Write: Bit 6 0 0 AFFC S8C SMP1 DSGN 0 0 0 0 0 CCF6 0 6 0 6 14 Bit6 14 Bit6 14 Bit6 14 Bit6 14 Bit 5 0 0 AWAI S4C SMP0 SCAN ETORF 0 0 0 0 CCF5 0 5 0 5 13 0 13 0 13 0 13 0 13 Bit 4 0 0 Bit 3 0 0 Bit 2 0 0 ETRIG FIFO PRS2 CC CC2 0 0 0 0 CCF2 0 2 0 2 10 0 10 0 10 0 10 0 10 Bit 1 0 0 ASCIE FRZ1 PRS1 CB CC1 0 0 0 0 CCF1 0 1 0 1 9 0 9 0 9 0 9 0 9 Bit 0 0 0 ASCIF FRZ0 PRS0 CA CC0 0 0 SC 0 CCF0 0 Bit 0 0 BIT 0 Bit8 0 Bit8 0 Bit8 0 Bit8 0 Bit8
ETRIGLE ETRIGP S2C PRS4 MULT FIFOR 0 0 0 0 CCF4 0 4 0 4 12 0 12 0 12 0 12 0 12 S1C PRS3 0 0 0 0 0 0 CCF3 0 3 0 3 11 0 11 0 11 0 11 0 11
40
MC9S12DJ64 Device User Guide -- V01.10
$0120 - $013F
Address $0139 $013A $013B $013C $013D $013E $013F Name ATD1DR4L ATD1DR5H ATD1DR5L ATD1DR6H ATD1DR6L ATD1DR7H ATD1DR7L Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write:
ATD1 (Analog to Digital Converter 10 Bit 8 Channel)
Bit 7 Bit7 Bit15 Bit7 Bit15 Bit7 Bit15 Bit7 Bit 6 Bit6 14 Bit6 14 Bit6 14 Bit6 Bit 5 0 13 0 13 0 13 0 Bit 4 0 12 0 12 0 12 0 Bit 3 0 11 0 11 0 11 0 Bit 2 0 10 0 10 0 10 0 Bit 1 0 9 0 9 0 9 0 Bit 0 0 Bit8 0 Bit8 0 Bit8 0
$0140 - $017F
Address $0140 $0141 $0142 $0143 $0144 $0145 $0146 $0147 $0148 $0149 $014A $014B $014C $014D $014E $014F Name Read: CAN0CTL0 Write: Read: CAN0CTL1 Write: Read: CAN0BTR0 Write: Read: CAN0BTR1 Write: Read: CAN0RFLG Write: Read: CAN0RIER Write: Read: CAN0TFLG Write: Read: CAN0TIER Write: Read: CAN0TARQ Write: Read: CAN0TAAK Write: Read: CAN0TBSEL Write: Read: CAN0IDAC Write: Read: Reserved Write: Read: Reserved Write: Read: CAN0RXERR Write: Read: CAN0TXERR Write:
CAN0 (Motorola Scalable CAN - MSCAN)
Bit 7 RXFRM CANE SJW1 SAMP WUPIF WUPIE 0 0 0 0 0 0 0 0 Bit 6 RXACT CLKSRC SJW0 Bit 5 CSWAI LOOPB BRP5 Bit 4 SYNCH LISTEN BRP4 Bit 3 TIME 0 BRP3 Bit 2 WUPE WUPM BRP2 Bit 1 SLPRQ SLPAK BRP1 Bit 0 INITRQ INITAK BRP0
TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 CSCIF CSCIE 0 0 0 0 0 0 0 0 RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF OVRIE TXE1 TXEIE1 RXF RXFIE TXE0 TXEIE0
RSTATE1 RSTATE0 TSTATE1 TSTATE0 0 0 0 0 0 IDAM1 0 0 0 0 0 0 0 IDAM0 0 0 0 0 0 0 0 0 0 0 TXE2 TXEIE2
ABTRQ2 ABTRQ1 ABTRQ0 ABTAK2 TX2 IDHIT2 0 0 ABTAK1 TX1 IDHIT1 0 0 ABTAK0 TX0 IDHIT0 0 0
RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0
41
MC9S12DJ64 Device User Guide -- V01.10
$0140 - $017F
Address $0150 $0153 $0154 $0157 $0158 $015B $015C $015F $0160 $016F $0170 $017F Name CAN0IDAR0 CAN0IDAR3 CAN0IDMR0 CAN0IDMR3 CAN0IDAR4 CAN0IDAR7 CAN0IDMR4 CAN0IDMR7 CAN0RXFG CAN0TXFG Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write:
CAN0 (Motorola Scalable CAN - MSCAN)
Bit 7 AC7 AM7 AC7 AM7 Bit 6 AC6 AM6 AC6 AM6 Bit 5 AC5 AM5 AC5 AM5 Bit 4 AC4 AM4 AC4 AM4 Bit 3 AC3 AM3 AC3 AM3 Bit 2 AC2 AM2 AC2 AM2 Bit 1 AC1 AM1 AC1 AM1 Bit 0 AC0 AM0 AC0 AM0
FOREGROUND RECEIVE BUFFER see Table 1-2 FOREGROUND TRANSMIT BUFFER see Table 1-2
Table 1-2 Detailed MSCAN Foreground Receive and Transmit Buffer Layout
Address $0160 Name Extended ID Standard ID CAN0RIDR0 Extended ID Standard ID CAN0RIDR1 Extended ID Standard ID CAN0RIDR2 Extended ID Standard ID CAN0RIDR3 CAN0RDSR0 CAN0RDSR7 Read: Read: Write: Read: Read: Write: Read: Read: Write: Read: Read: Write: Read: Write: Read: CANR0DLR Write: Read: Reserved Write: Read: CAN0RTSRH Write: Read: CAN0RTSRL Write: Extended ID Read: CAN0TIDR0 Write: Standard ID Read: Write: Extended ID Read: CAN0TIDR1 Write: Standard ID Read: Write: Bit 7 ID28 ID10 ID20 ID2 ID14 Bit 6 ID27 ID9 ID19 ID1 ID13 Bit 5 ID26 ID8 ID18 ID0 ID12 Bit 4 ID25 ID7 SRR=1 RTR ID11 Bit 3 ID24 ID6 IDE=1 IDE=0 ID10 Bit 2 ID23 ID5 ID17 Bit 1 ID22 ID4 ID16 Bit 0 ID21 ID3 ID15
$0161
ID9
ID8
ID7
$0162
ID6
ID5
ID4
ID3
ID2
ID1
ID0
RTR
$0163 $0164$016B $016C $016D $016E $016F
DB7
DB6
DB5
DB4
DB3 DLC3
DB2 DLC2
DB1 DLC1
DB0 DLC0
TSR15 TSR7 ID28 ID10 ID20 ID2
TSR14 TSR6 ID27 ID9 ID19 ID1
TSR13 TSR5 ID26 ID8 ID18 ID0
TSR12 TSR4 ID25 ID7 SRR=1 RTR
TSR11 TSR3 ID24 ID6 IDE=1 IDE=0
TSR10 TSR2 ID23 ID5 ID17
TSR9 TSR1 ID22 ID4 ID16
TSR8 TSR0 ID21 ID3 ID15
$0170
$0171
42
MC9S12DJ64 Device User Guide -- V01.10
Table 1-2 Detailed MSCAN Foreground Receive and Transmit Buffer Layout
Address $0172 Name Extended ID CAN0TIDR2 Standard ID Extended ID CAN0TIDR3 Standard ID CAN0TDSR0 CAN0TDSR7 CAN0TDLR CON0TTBPR CAN0TTSRH CAN0TTSRL Bit 7 Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: ID14 Bit 6 ID13 Bit 5 ID12 Bit 4 ID11 Bit 3 ID10 Bit 2 ID9 Bit 1 ID8 Bit 0 ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
RTR
$0173 $0174$xx1B $017C $017D $017E $017F
DB7
DB6
DB5
DB4
DB3 DLC3
DB2 DLC2 PRIO2 TSR10 TSR2
DB1 DLC1 PRIO1 TSR9 TSR1
DB0 DLC0 PRIO0 TSR8 TSR0
PRIO7 TSR15 TSR7
PRIO6 TSR14 TSR6
PRIO5 TSR13 TSR5
PRIO4 TSR12 TSR4
PRIO3 TSR11 TSR3
$0180 - $023F
Address $0180 $023F Name Reserved Read: Write:
Reserved
Bit 7 0 Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 0 Bit 1 0 Bit 0 0
$0240 - $027F
Address $0240 $0241 $0242 $0243 $0244 $0245 $0246 $0247 $0248 $0249 Name PTT PTIT DDRT RDRT PERT PPST Reserved Reserved PTS PTIS
PIM (Port Integration Module)
Bit 7 Read: PTT7 Write: Read: PTIT7 Write: Read: DDRT7 Write: Read: RDRT7 Write: Read: PERT7 Write: Read: PPST7 Write: Read: 0 Write: Read: 0 Write: Read: PTS7 Write: Read: PTIS7 Write: Bit 6 PTT6 PTIT6 DDRT7 RDRT6 PERT6 PPST6 0 0 PTS6 PTIS6 Bit 5 PTT5 PTIT5 DDRT5 RDRT5 PERT5 PPST5 0 0 PTS5 PTIS5 Bit 4 PTT4 PTIT4 DDRT4 RDRT4 PERT4 PPST4 0 0 PTS4 PTIS4 Bit 3 PTT3 PTIT3 DDRT3 RDRT3 PERT3 PPST3 0 0 PTS3 PTIS3 Bit 2 PTT2 PTIT2 DDRT2 RDRT2 PERT2 PPST2 0 0 PTS2 PTIS2 Bit 1 PTT1 PTIT1 DDRT1 RDRT1 PERT1 PPST1 0 0 PTS1 PTIS1 Bit 0 PTT0 PTIT0 DDRT0 RDRT0 PERT0 PPST0 0 0 PTS0 PTIS0
43
MC9S12DJ64 Device User Guide -- V01.10
$0240 - $027F
Address $024A $024B $024C $024D $024E $024F $0250 $0251 $0252 $0253 $0254 $0255 $0256 $0257 $0258 $0259 $025A $025B $025C $025D $025E $025F $0260 $0261 $0262 Name DDRS RDRS PERS PPSS WOMS Reserved PTM PTIM DDRM RDRM PERM PPSM WOMM MODRR PTP PTIP DDRP RDRP PERP PPSP PIEP PIFP PTH PTIH DDRH Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write: Read: Write:
PIM (Port Integration Module)
Bit 7 DDRS7 RDRS7 PERS7 PPSS7 WOMS7 0 PTM7 PTIM7 DDRM7 RDRM7 PERM7 PPSM7 Bit 6 DDRS7 RDRS6 PERS6 PPSS6 WOMS6 0 PTM6 PTIM6 DDRM7 RDRM6 PERM6 PPSM6 Bit 5 DDRS5 RDRS5 PERS5 PPSS5 WOMS5 0 PTM5 PTIM5 DDRM5 RDRM5 PERM5 PPSM5 Bit 4 DDRS4 RDRS4 PERS4 PPSS4 WOMS4 0 PTM4 PTIM4 DDRM4 RDRM4 PERM4 PPSM4 Bit 3 DDRS3 RDRS3 PERS3 PPSS3 WOMS3 0 PTM3 PTIM3 DDRM3 RDRM3 PERM3 PPSM3 Bit 2 DDRS2 RDRS2 PERS2 PPSS2 WOMS2 0 PTM2 PTIM2 DDRM2 RDRM2 PERM2 PPSM2 Bit 1 DDRS1 RDRS1 PERS1 PPSS1 WOMS1 0 PTM1 PTIM1 DDRM1 RDRM1 PERM1 PPSM1 Bit 0 DDRS0 RDRS0 PERS0 PPSS0 WOMS0 0 PTM0 PTIM0 DDRM0 RDRM0 PERM0 PPSM0
WOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0 0 PTP7 PTIP7 DDRP7 RDRP7 PERP7 PPSP7 PIEP7 PIFP7 PTH7 PTIH7 DDRH7 0 PTP6 PTIP6 DDRP7 RDRP6 PERP6 PPSP6 PIEP6 PIFP6 PTH6 PTIH6 DDRH7 0 PTP5 PTIP5 DDRP5 RDRP5 PERP5 PPSP5 PIEP5 PIFP5 PTH5 PTIH5 DDRH5 MODRR4 PTP4 PTIP4 DDRP4 RDRP4 PERP4 PPSP4 PIEP4 PIFP4 PTH4 PTIH4 DDRH4 0 PTP3 PTIP3 DDRP3 RDRP3 PERP3 PPSP3 PIEP3 PIFP3 PTH3 PTIH3 DDRH3 0 PTP2 PTIP2 DDRP2 RDRP2 PERP2 PPSP2 PIEP2 PIFP2 PTH2 PTIH2 DDRH2 MODRR1 MODRR0 PTP1 PTIP1 DDRP1 RDRP1 PERP1 PPSP1 PIEP1 PIFP1 PTH1 PTIH1 DDRH1 PTP0 PTIP0 DDRP0 RDRP0 PERP0 PPSS0 PIEP0 PIFP0 PTH0 PTIH0 DDRH0
44
MC9S12DJ64 Device User Guide -- V01.10
$0240 - $027F
Address $0263 $0264 $0265 $0266 $0267 $0268 $0269 $026A $026B $026C $026D $026E $026F $0270 $027F Name RDRH PERH PPSH PIEH PIFH PTJ PTIJ DDRJ RDRJ PERJ PPSJ PIEJ PIFJ Reserved
PIM (Port Integration Module)
Bit 7 Read: RDRH7 Write: Read: PERH7 Write: Read: PPSH7 Write: Read: PIEH7 Write: Read: PIFH7 Write: Read: PTJ7 Write: Read: PTIJ7 Write: Read: DDRJ7 Write: Read: RDRJ7 Write: Read: PERJ7 Write: Read: PPSJ7 Write: Read: PIEJ7 Write: Read: PIFJ7 Write: Read: 0 Write: Bit 6 RDRH6 PERH6 PPSH6 PIEH6 PIFH6 PTJ6 PTIJ6 DDRJ7 RDRJ6 PERJ6 PPSJ6 PIEJ6 PIFJ6 0 Bit 5 RDRH5 PERH5 PPSH5 PIEH5 PIFH5 0 0 0 0 0 0 0 0 0 Bit 4 RDRH4 PERH4 PPSH4 PIEH4 PIFH4 0 0 0 0 0 0 0 0 0 Bit 3 RDRH3 PERH3 PPSH3 PIEH3 PIFH3 0 0 0 0 0 0 0 0 0 Bit 2 RDRH2 PERH2 PPSH2 PIEH2 PIFH2 0 0 0 0 0 0 0 0 0 Bit 1 RDRH1 PERH1 PPSH1 PIEH1 PIFH1 PTJ1 PTIJ1 DDRJ1 RDRJ1 PERJ1 PPSJ1 PIEJ1 PIFJ1 0 Bit 0 RDRH0 PERH0 PPSH0 PIEH0 PIFH0 PTJ0 PTIJ0 DDRJ0 RDRJ0 PERJ0 PPSJ0 PIEJ0 PIFJ0 0
$0280 - $03FF
Address $0280 $03FF Name Reserved Read: Write:
Reserved
Bit 7 0 Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 0 Bit 1 0 Bit 0 0
45
MC9S12DJ64 Device User Guide -- V01.10
1.6 Part ID Assignments
The part ID is located in two 8-bit registers PARTIDH and PARTIDL (addresses $001A and $001B after reset). The read-only value is a unique part ID for each revision of the chip. Table 1-3 shows the assigned part ID number. Table 1-3 Assigned Part ID Numbers
Device MC9S12DJ64 MC9S12DJ64 MC9S12DJ64 Mask Set Number 0L86D 1L86D 2L86D Part ID1 $0200 $0201 $02012
NOTES: 1. The coding is as follows: Bit 15-12: Major family identifier Bit 11-8: Minor family identifier Bit 7-4: Major mask set revision number including FAB transfers Bit 3-0: Minor - non full - mask set revision 2. 1L86D is identical to 2L86D except improved ESD performance on 2L86D
The device memory sizes are located in two 8-bit registers MEMSIZ0 and MEMSIZ1 (addresses $001C and $001D after reset). Table 1-4 shows the read-only values of these registers. Refer to section Module Mapping and Control (MMC) of HCS12 Core User Guide for further details.
Table 1-4 Memory size registers
Register name MEMSIZ0 MEMSIZ1 Value $11 $80
46
MC9S12DJ64 Device User Guide -- V01.10
Section 2 Signal Description
This section describes signals that connect off-chip. It includes a pinout diagram, a table of signal properties, and detailed discussion of signals. It is built from the signal description sections of the Block User Guides of the individual IP blocks on the device.
2.1 Device Pinout
The MC9S12DJ64 is available in a 112-pin low profile quad flat pack (LQFP) and in a 80-pin quad flat pack (QFP). Most pins perform two or more functions, as described in the Signal Descriptions. Figure 2-1 and Figure 2-2 show the pin assignments.
47
MC9S12DJ64 Device User Guide -- V01.10
Figure 2-1 Pin Assignments in 112-pin LQFP for MC9S12DJ64
48
ADDR5/DATA5/PB5 ADDR6/DATA6/PB6 ADDR7/DATA7/PB7 KWH7/PH7 KWH6/PH6 KWH5/PH5 KWH4/PH4 XCLKS/NOACC/PE7 MODB/IPIPE1/PE6 MODA/IPIPE0/PE5 ECLK/PE4 VSSR VDDR RESET VDDPLL XFC VSSPLL EXTAL XTAL TEST KWH3/PH3 KWH2/PH2 KWH1/PH1 KWH0/PH0 LSTRB/TAGLO/PE3 R/W/PE2 IRQ/PE1 XIRQ/PE0
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
PWM3/KWP3/PP3 PWM2/KWP2/PP2 PWM1/KWP1/PP1 PWM0/KWP0/PP0 XADDR17/PK3 XADDR16/PK2 XADDR15/PK1 XADDR14/PK0 IOC0/PT0 IOC1/PT1 IOC2/PT2 IOC3/PT3 VDD1 VSS1 IOC4/PT4 IOC5/PT5 IOC6/PT6 IOC7/PT7 XADDR19/PK5 XADDR18/PK4 KWJ1/PJ1 KWJ0/PJ0 MODC/TAGHI/BKGD ADDR0/DATA0/PB0 ADDR1/DATA1/PB1 ADDR2/DATA2/PB2 ADDR3/DATA3/PB3 ADDR4/DATA4/PB4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85
PP4/KWP4/PWM4 PP5/KPW5/PWM5 PP6/KWP6/PWM6 PP7/KWP7/PWM7 PK7/ECS/ROMCTL VDDX VSSX PM0/RXCAN0/RXB PM1/TXCAN0/TXB PM2/RXCAN0/MISO0 PM3/TXCAN0/SS0 PM4/RXCAN0/MOSI PM5/TXCAN0/SCK0 PJ6/KWJ6/SDA/RXCAN0 PJ7/KWJ7/SCL/TXCAN0 VREGEN PS7/SS0 PS6/SCK0 PS5/MOSI0 PS4/MISO0 PS3/TXD1 PS2/RXD1 PS1/TXD0 PS0/RXD0 PM6 PM7 VSSA VRL 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57
MC9S12DJ64
112LQFP
VRH VDDA PAD15/AN15/ETRIG1 PAD07/AN07/ETRIG0 PAD14/AN14 PAD06/AN06 PAD13/AN13 PAD05/AN05 PAD12/AN12 PAD04/AN04 PAD11/AN11 PAD03/AN03 PAD10/AN10 PAD02/AN02 PAD09/AN09 PAD01/AN01 PAD08/AN08 PAD00/AN00 VSS2 VDD2 PA7/ADDR15/DATA15 PA6/ADDR14/DATA14 PA5/ADDR13/DATA13 PA4/ADDR12/DATA12 PA3/ADDR11/DATA11 PA2/ADDR10/DATA10 PA1/ADDR9/DATA9 PA0/ADDR8/DATA8
Signals shown in Bold are not available on the 80 Pin Package
MC9S12DJ64 Device User Guide -- V01.10
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
PP4/KWP4/PWM4 PP5/KWP5/PWM5 PP7/KWP7/PWM7 VDDX VSSX PM0/RXCAN0/RXB PM1/TXCAN0/TXB PM2/RXCAN0/MISO0 PM3/TXCAN0/SS0 PM4/RXCAN0/MOSI0 PM5/TXCAN0/SCK0 PJ6/KWJ6/SDA/RXCAN0 PJ7/KWJ7/SCL/TXCAN0 VREGEN PS3/TXD1 PS2/RXD1 PS1/TXD0 PS0/RXD0 VSSA VRL PWM3/KWP3/PP3 PWM2/KWP2/PP2 PWM1/KWP1/PP1 PWM0/KWP0/PP0 IOC0/PT0 IOC1/PT1 IOC2/PT2 IOC3/PT3 VDD1 VSS1 IOC4/PT4 IOC5/PT5 IOC6/PT6 IOC7/PT7 MODC/TAGHI/BKGD ADDR0/DATA0/PB0 ADDR1/DATA1/PB1 ADDR2/DATA2/PB2 ADDR3/DATA3/PB3 ADDR4/DATA4/PB4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
MC9S12DJ64
80 QFP
VRH VDDA PAD07/AN07/ETRIG0 PAD06/AN06 PAD05/AN05 PAD04/AN04 PAD03/AN03 PAD02/AN02 PAD01/AN01 PAD00/AN00 VSS2 VDD2 PA7/ADDR15/DATA15 PA6/ADDR14/DATA14 PA5/ADDR13/DATA13 PA4/ADDR12/DATA12 PA3/ADDR11/DATA11 PA2/ADDR10/DATA10 PA1/ADDR9/DATA9 PA0/ADDR8/DATA8
Figure 2-2 Pin Assignments in 80-pin QFP for MC9S12DJ64
2.2 Signal Properties Summary
Table 2-1 summarizes the pin functionality. Signals shown in bold are not available in the 80 pin package.
ADDR5/DATA5/PB5 ADDR6/DATA6/PB6 ADDR7/DATA7/PB7 XCLKS/NOACC/PE7 MODB/IPIPE1/PE6 MODA/IPIPE0/PE5 ECLK/PE4 VSSR VDDR RESET VDDPLL XFC VSSPLL EXTAL XTAL TEST LSTRB/TAGLO/PE3 R/W/PE2 IRQ/PE1 XIRQ/PE0
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
49
MC9S12DJ64 Device User Guide -- V01.10
Table 2-1 Signal Properties
Pin Name Function1 EXTAL XTAL RESET TEST VREGEN XFC BKGD PAD15 PAD[14:08] PAD07 PAD[06:00] PA[7:0] PB[7:0] PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 PH7 PH6 PH5 PH4 PH3 PH2 PH1 PH0 PJ7 PJ6 PJ[1:0] Pin Name Function2 -- -- -- -- -- -- TAGHI AN15 AN[14:08] AN07 AN[06:00] ADDR[15:8]/ DATA[15:8] ADDR[7:0]/ DATA[7:0] NOACC IPIPE1 IPIPE0 ECLK LSTRB R/W IRQ XIRQ KWH7 KWH6 KWH5 KWH4 KWH3 KWH2 KWH1 KWH0 KWJ7 KWJ6 KWJ[1:0] Pin Name Pin Name Powered Function3 Function4 by -- -- -- -- -- -- MODC ETRIG1 -- ETRIG0 -- -- -- XCLKS MODB MODA -- TAGLO -- -- -- -- -- -- -- -- -- -- -- SCL SDA -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TXCAN0 RXCAN0 -- VDDX PERJ/ PPSJ Up PERH/ PPSH Disabled VDDR PUCR/ PUPEE Up PUCR/ PUPAE PUCR/ PUPBE PUCR/ PUPEE Internal Pull Resistor CTRL Reset State
Description
VDDPLL VDDR N.A. VDDX VDDPLL VDDR Always Up Up None None
Oscillator Pins External Reset Test Input Voltage Regulator Enable Input PLL Loop Filter Background Debug, Tag High, Mode Input Port AD Input, Analog Input AN7 of ATD1, External Trigger Input of ATD1
VDDA
None
None
Port AD Inputs, Analog Inputs AN[6:0] of ATD1 Port AD Input, Analog Input AN7 of ATD0, External Trigger Input of ATD0 Port AD Inputs, Analog Inputs AN[6:0] of ATD0 Port A I/O, Multiplexed Address/Data
Disabled Port B I/O, Multiplexed Address/Data Up Port E I/O, Access, Clock Select
While RESET pin is Port E I/O, Pipe Status, Mode Input low: Port E I/O, Pipe Status, Mode Input Down Port E I/O, Bus Clock Output Port E I/O, Byte Strobe, Tag Low Port E I/O, R/W in expanded modes Port E Input, Maskable Interrupt Port E Input, Non Maskable Interrupt Port H I/O, Interrupt Port H I/O, Interrupt Port H I/O, Interrupt Port H I/O, Interrupt Port H I/O, Interrupt Port H I/O, Interrupt Port H I/O, Interrupt Port H I/O, Interrupt Port J I/O, Interrupt, SCL of IIC, TX of CAN0 Port J I/O, Interrupt, SDA of IIC, RX of CAN0 Port J I/O, Interrupts
50
MC9S12DJ64 Device User Guide -- V01.10
Internal Pull Resistor CTRL PUCR/ PUPKE Reset State Up
Pin Name Function1
Pin Name Function2
Pin Name Pin Name Powered Function3 Function4 by
Description Port K I/O, Emulation Chip Select, ROM On Enable Port K I/O, Extended Addresses Port M I/O Port M I/O Port M I/O, TX of CAN0, SCK of SPI0
PK7 PK[5:0] PM7 PM6 PM5 PM4 PM3 PM2 PM1 PM0 PP7 PP6 PP5 PP4 PP3 PP2 PP1 PP0 PS7 PS6 PS5 PS4 PS3 PS2 PS1 PS0 PT[7:0]
ECS XADDR[19:14] -- -- TXCAN0 RXCAN0 TXCAN0 RXCAN0 TXCAN0 RXCAN0 KWP7 KWP6 KWP5 KWP4 KWP3 KWP2 KWP1 KWP0 SS0 SCK0 MOSI0 MISO0 TXD1 RXD1 TXD0 RXD0 IOC[7:0]
ROMCTL -- -- -- SCK MOSI SS0 MISO0 TXB RXB PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 -- -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- VDDX
PERM/ PPSM
Port M I/O, RX of CAN0, MOSI of SPI0 Port M I/O, TX of CAN0, SS of SPI0 Port M I/O, RX of CAN0, MISO of SPI0 Port M I/O, TX of CAN0, RX of BDLC Port M I/O, RX of CAN0, RX of BDLC Disabled Port P I/O, Interrupt, Channel 7 of PWM Port P I/O, Interrupt, PWM Channel 6 Port P I/O, Interrupt, PWM Channel 5
PERP/ PPSP
Port P I/O, Interrupt, PWM Channel 4 Port P I/O, Interrupt, PWM Channel 3 Port P I/O, Interrupt, PWM Channel 2 Port P I/O, Interrupt, PWM Channel 1 Port P I/O, Interrupt, PWM Channel 0 Port S I/O, SS of SPI0 Port S I/O, SCK of SPI0 Port S I/O, MOSI of SPI0
PERS/ PPSS
Up
Port S I/O, MISO of SPI0 Port S I/O, TXD of SCI1 Port S I/O, RXD of SCI1 Port S I/O, TXD of SCI0 Port S I/O, RXD of SCI0
PERT/ PPST
Disabled Port T I/O, Timer channels
2.3 Detailed Signal Descriptions
2.3.1 EXTAL, XTAL -- Oscillator Pins
EXTAL and XTAL are the crystal driver and external clock pins. On reset all the device clocks are derived from the EXTAL input frequency. XTAL is the crystal output.
51
MC9S12DJ64 Device User Guide -- V01.10
2.3.2 RESET -- External Reset Pin
An active low bidirectional control signal, it acts as an input to initialize the MCU to a known start-up state, and an output when an internal MCU function causes a reset.
2.3.3 TEST -- Test Pin
This input only pin is reserved for test.
NOTE:
The TEST pin must be tied to VSS in all applications.
2.3.4 VREGEN -- Voltage Regulator Enable Pin
This input only pin enables or disables the on-chip voltage regulator.
2.3.5 XFC -- PLL Loop Filter Pin
PLL loop filter. Please ask your Motorola representative for the interactive application note to compute PLL loop filter elements. Any current leakage on this pin must be avoided.
XFC R0 MCU CS VDDPLL VDDPLL
CP
Figure 2-3 PLL Loop Filter Connections
2.3.6 BKGD / TAGHI / MODC -- Background Debug, Tag High, and Mode Pin
The BKGD/TAGHI/MODC pin is used as a pseudo-open-drain pin for the background debug communication. In MCU expanded modes of operation when instruction tagging is on, an input low on this pin during the falling edge of E-clock tags the high half of the instruction word being read into the instruction queue. It is used as a MCU operating mode select pin during reset. The state of this pin is latched to the MODC bit at the rising edge of RESET. This pin has a permanently enabled pull-up device.
2.3.7 PAD15 / AN15 / ETRIG1 -- Port AD Input Pin of ATD1
PAD15 is a general purpose input pin and analog input AN7 of the analog to digital converter ATD1. It can act as an external trigger input for the ATD1.
52
MC9S12DJ64 Device User Guide -- V01.10
2.3.8 PAD[14:08] / AN[14:08] -- Port AD Input Pins ATD1
PAD14 - PAD08 are general purpose input pins and analog inputs AN[6:0] of the analog to digital converter ATD1.
2.3.9 PAD07 / AN07 / ETRIG0 -- Port AD Input Pin of ATD0
PAD07 is a general purpose input pin and analog input AN0 of the analog to digital converter ATD0. It can act as an external trigger input for the ATD0.
2.3.10 PAD[06:00] / AN[06:00] -- Port AD Input Pins of ATD0
PAD06 - PAD00 are general purpose input pins and analog inputs AN[6:0] of the analog to digital converter ATD0.
2.3.11 PA[7:0] / ADDR[15:8] / DATA[15:8] -- Port A I/O Pins
PA7-PA0 are general purpose input or output pins. In MCU expanded modes of operation, these pins are used for the multiplexed external address and data bus.
2.3.12 PB[7:0] / ADDR[7:0] / DATA[7:0] -- Port B I/O Pins
PB7-PB0 are general purpose input or output pins. In MCU expanded modes of operation, these pins are used for the multiplexed external address and data bus.
2.3.13 PE7 / NOACC / XCLKS -- Port E I/O Pin 7
PE7 is a general purpose input or output pin. During MCU expanded modes of operation, the NOACC signal, when enabled, is used to indicate that the current bus cycle is an unused or "free" cycle. This signal will assert when the CPU is not using the bus. The XCLKS is an input signal which controls whether a crystal in combination with the internal Colpitts (low power) oscillator is used or whether Pierce oscillator/external clock circuitry is used. The state of this pin is latched at the rising edge of RESET. If the input is a logic low the EXTAL pin is configured for an external clock drive or a Pierce Oscillator. If input is a logic high a Colpitts oscillator circuit is configured on EXTAL and XTAL. Since this pin is an input with a pull-up device during reset, if the pin is left floating, the default configuration is a Colpitts oscillator circuit on EXTAL and XTAL.
53
MC9S12DJ64 Device User Guide -- V01.10
EXTAL CDC * MCU XTAL C2 VSSPLL * Due to the nature of a translated ground Colpitts oscillator a DC voltage bias is applied to the crystal Please contact the crystal manufacturer for crystal DC bias conditions and recommended capacitor value CDC. C1 Crystal or ceramic resonator
Figure 2-4 Colpitts Oscillator Connections (PE7=1)
EXTAL
C3
MCU RS
*
RB
Crystal or ceramic resonator C4
XTAL
VSSPLL
* Rs can be zero (shorted) when used with higher frequency crystals. Refer to manufacturer's data.
Figure 2-5 Pierce Oscillator Connections (PE7=0)
EXTAL
MCU
CMOS-COMPATIBLE EXTERNAL OSCILLATOR (VDDPLL-Level)
XTAL
not connected
Figure 2-6 External Clock Connections (PE7=0)
54
MC9S12DJ64 Device User Guide -- V01.10
2.3.14 PE6 / MODB / IPIPE1 -- Port E I/O Pin 6
PE6 is a general purpose input or output pin. It is used as a MCU operating mode select pin during reset. The state of this pin is latched to the MODB bit at the rising edge of RESET. This pin is shared with the instruction queue tracking signal IPIPE1. This pin is an input with a pull-down device which is only active when RESET is low.
2.3.15 PE5 / MODA / IPIPE0 -- Port E I/O Pin 5
PE5 is a general purpose input or output pin. It is used as a MCU operating mode select pin during reset. The state of this pin is latched to the MODA bit at the rising edge of RESET. This pin is shared with the instruction queue tracking signal IPIPE0. This pin is an input with a pull-down device which is only active when RESET is low.
2.3.16 PE4 / ECLK -- Port E I/O Pin 4
PE4 is a general purpose input or output pin. It can be configured to drive the internal bus clock ECLK. ECLK can be used as a timing reference.
2.3.17 PE3 / LSTRB / TAGLO -- Port E I/O Pin 3
PE3 is a general purpose input or output pin. In MCU expanded modes of operation, LSTRB can be used for the low-byte strobe function to indicate the type of bus access and when instruction tagging is on, TAGLO is used to tag the low half of the instruction word being read into the instruction queue.
2.3.18 PE2 / R/W -- Port E I/O Pin 2
PE2 is a general purpose input or output pin. In MCU expanded modes of operations, this pin drives the read/write output signal for the external bus. It indicates the direction of data on the external bus.
2.3.19 PE1 / IRQ -- Port E Input Pin 1
PE1 is a general purpose input pin and the maskable interrupt request input that provides a means of applying asynchronous interrupt requests. This will wake up the MCU from STOP or WAIT mode.
2.3.20 PE0 / XIRQ -- Port E Input Pin 0
PE0 is a general purpose input pin and the non-maskable interrupt request input that provides a means of applying asynchronous interrupt requests. This will wake up the MCU from STOP or WAIT mode.
2.3.21 PH7 / KWH7 -- Port H I/O Pin 7
PH7 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
55
MC9S12DJ64 Device User Guide -- V01.10
2.3.22 PH6 / KWH6 -- Port H I/O Pin 6
PH6 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
2.3.23 PH5 / KWH5 -- Port H I/O Pin 5
PH5 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
2.3.24 PH4 / KWH4 -- Port H I/O Pin 2
PH4 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
2.3.25 PH3 / KWH3 -- Port H I/O Pin 3
PH3 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
2.3.26 PH2 / KWH2 -- Port H I/O Pin 2
PH2 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
2.3.27 PH1 / KWH1 -- Port H I/O Pin 1
PH1 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
2.3.28 PH0 / KWH0 -- Port H I/O Pin 0
PH0 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
2.3.29 PJ7 / KWJ7 / SCL / TXCAN0 -- PORT J I/O Pin 7
PJ7 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as the serial clock pin SCL of the IIC module. It can be configured as the transmit pin TXCAN of the Motorola Scalable Controller Area Network controller 0 (CAN0).
56
MC9S12DJ64 Device User Guide -- V01.10
2.3.30 PJ6 / KWJ6 / SDA / RXCAN0 -- PORT J I/O Pin 6
PJ6 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as the serial data pin SDA of the IIC module. It can be configured as the receive pin RXCAN of the Motorola Scalable Controller Area Network controller 0 (CAN0).
2.3.31 PJ[1:0] / KWJ[1:0] -- Port J I/O Pins [1:0]
PJ1 and PJ0 are general purpose input or output pins. They can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode.
2.3.32 PK7 / ECS / ROMCTL -- Port K I/O Pin 7
PK7 is a general purpose input or output pin. During MCU expanded modes of operation, this pin is used as the emulation chip select output (ECS). During MCU expanded modes of operation, this pin is used to enable the Flash EEPROM memory in the memory map (ROMCTL). At the rising edge of RESET, the state of this pin is latched to the ROMON bit. For a complete list of modes refer to 4.2 Chip Configuration Summary.
2.3.33 PK[5:0] / XADDR[19:14] -- Port K I/O Pins [5:0]
PK5-PK0 are general purpose input or output pins. In MCU expanded modes of operation, these pins provide the expanded address XADDR[19:14] for the external bus.
2.3.34 PM7 -- Port M I/O Pin 7
PM7 is a general purpose input or output pin.
2.3.35 PM6 -- Port M I/O Pin 6
PM6 is a general purpose input or output pin.
2.3.36 PM5 / TXCAN0 / SCK0 -- Port M I/O Pin 5
PM5 is a general purpose input or output pin. It can be configured as the transmit pin TXCAN of the Motorola Scalable Controller Area Network controller 0 (CAN0). It can be configured as the serial clock pin SCK of the Serial Peripheral Interface 0 (SPI0).
2.3.37 PM4 / RXCAN0 / MOSI0 -- Port M I/O Pin 4
PM4 is a general purpose input or output pin. It can be configured as the receive pin RXCAN of the Motorola Scalable Controller Area Network controller 0 (CAN0). It can be configured as the master output (during master mode) or slave input pin (during slave mode) MOSI for the Serial Peripheral Interface 0 (SPI0).
57
MC9S12DJ64 Device User Guide -- V01.10
2.3.38 PM3 / TXCAN0 / SS0 -- Port M I/O Pin 3
PM3 is a general purpose input or output pin. It can be configured as the transmit pin TXCAN of the Motorola Scalable Controller Area Network controller 0 (CAN0). It can be configured as the slave select pin SS of the Serial Peripheral Interface 0 (SPI0).
2.3.39 PM2 / RXCAN0 / MISO0 -- Port M I/O Pin 2
PM2 is a general purpose input or output pin. It can be configured as the receive pin RXCAN of the Motorola Scalable Controller Area Network controller 0 (CAN0). It can be configured as the master input (during master mode) or slave output pin (during slave mode) MISO for the Serial Peripheral Interface 0 (SPI0).
2.3.40 PM1 / TXCAN0 / TXB -- Port M I/O Pin 1
PM1 is a general purpose input or output pin. It can be configured as the transmit pin TXCAN of the Motorola Scalable Controller Area Network controller 0 (CAN0). It can be configured as the transmit pin TXB of the BDLC.
2.3.41 PM0 / RXCAN0 / RXB -- Port M I/O Pin 0
PM0 is a general purpose input or output pin. It can be configured as the receive pin RXCAN of the Motorola Scalable Controller Area Network controller 0 (CAN0). It can be configured as the receive pin RXB of the BDLC.
2.3.42 PP7 / KWP7 / PWM7 -- Port P I/O Pin 7
PP7 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 7 output.
2.3.43 PP6 / KWP6 / PWM6 -- Port P I/O Pin 6
PP6 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 6 output.
2.3.44 PP5 / KWP5 / PWM5 -- Port P I/O Pin 5
PP5 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 5 output.
2.3.45 PP4 / KWP4 / PWM4 -- Port P I/O Pin 4
PP4 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 4 output.
58
MC9S12DJ64 Device User Guide -- V01.10
2.3.46 PP3 / KWP3 / PWM3 -- Port P I/O Pin 3
PP3 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 3 output.
2.3.47 PP2 / KWP2 / PWM2 -- Port P I/O Pin 2
PP2 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 2 output.
2.3.48 PP1 / KWP1 / PWM1 -- Port P I/O Pin 1
PP1 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 1 output.
2.3.49 PP0 / KWP0 / PWM0 -- Port P I/O Pin 0
PP0 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 0 output.
2.3.50 PS7 / SS0 -- Port S I/O Pin 7
PS6 is a general purpose input or output pin. It can be configured as the slave select pin SS of the Serial Peripheral Interface 0 (SPI0).
2.3.51 PS6 / SCK0 -- Port S I/O Pin 6
PS6 is a general purpose input or output pin. It can be configured as the serial clock pin SCK of the Serial Peripheral Interface 0 (SPI0).
2.3.52 PS5 / MOSI0 -- Port S I/O Pin 5
PS5 is a general purpose input or output pin. It can be configured as master output (during master mode) or slave input pin (during slave mode) MOSI of the Serial Peripheral Interface 0 (SPI0).
2.3.53 PS4 / MISO0 -- Port S I/O Pin 4
PS4 is a general purpose input or output pin. It can be configured as master input (during master mode) or slave output pin (during slave mode) MOSI of the Serial Peripheral Interface 0 (SPI0).
2.3.54 PS3 / TXD1 -- Port S I/O Pin 3
PS3 is a general purpose input or output pin. It can be configured as the transmit pin TXD of Serial Communication Interface 1 (SCI1).
59
MC9S12DJ64 Device User Guide -- V01.10
2.3.55 PS2 / RXD1 -- Port S I/O Pin 2
PS2 is a general purpose input or output pin. It can be configured as the receive pin RXD of Serial Communication Interface 1 (SCI1).
2.3.56 PS1 / TXD0 -- Port S I/O Pin 1
PS1 is a general purpose input or output pin. It can be configured as the transmit pin TXD of Serial Communication Interface 0 (SCI0).
2.3.57 PS0 / RXD0 -- Port S I/O Pin 0
PS0 is a general purpose input or output pin. It can be configured as the receive pin RXD of Serial Communication Interface 0 (SCI0).
2.3.58 PT[7:0] / IOC[7:0] -- Port T I/O Pins [7:0]
PT7-PT0 are general purpose input or output pins. They can be configured as input capture or output compare pins IOC7-IOC0 of the Enhanced Capture Timer (ECT).
2.4 Power Supply Pins
MC9S12DJ64 power and ground pins are described below.
NOTE:
All VSS pins must be connected together in the application.
Table 2-2 MC9S12DJ64 Power and Ground Connection Summary
Mnemonic VDD1, 2 VSS1, 2 VDDR VSSR VDDX VSSX VDDA VSSA VRL VRH Pin Number 112-pin QFP 13, 65 14, 66 41 40 107 106 83 86 85 84 Nominal Voltage 2.5V 0V 5.0V 0V 5.0V 0V 5.0V 0V 0V 5.0V Description Internal power and ground generated by internal regulator External power and ground, supply to pin drivers and internal voltage regulator. External power and ground, supply to pin drivers. Operating voltage and ground for the analog-to-digital converters and the reference for the internal voltage regulator, allows the supply voltage to the A/D to be bypassed independently. Reference voltages for the analog-to-digital converter.
60
MC9S12DJ64 Device User Guide -- V01.10 Pin Number 112-pin QFP 43 45 97 Nominal Voltage 2.5V 0V 5.0V
Mnemonic VDDPLL VSSPLL VREGEN
Description Provides operating voltage and ground for the Phased-Locked Loop. This allows the supply voltage to the PLL to be bypassed independently. Internal power and ground generated by internal regulator. Internal Voltage Regulator enable/disable
2.4.1 VDDX, VSSX -- Power & Ground Pins for I/O Drivers
External power and ground for I/O drivers. Because fast signal transitions place high, short-duration current demands on the power supply, use bypass capacitors with high-frequency characteristics and place them as close to the MCU as possible. Bypass requirements depend on how heavily the MCU pins are loaded. VDDX and VSSX are the supplies for Ports J, K, M, P, T and S.
2.4.2 VDDR, VSSR -- Power & Ground Pins for I/O Drivers & for Internal Voltage Regulator
External power and ground for I/O drivers and input to the internal voltage regulator. Because fast signal transitions place high, short-duration current demands on the power supply, use bypass capacitors with high-frequency characteristics and place them as close to the MCU as possible. Bypass requirements depend on how heavily the MCU pins are loaded. VDDR and VSSR are the supplies for Ports A, B, E and H.
2.4.3 VDD1, VDD2, VSS1, VSS2 -- Core Power Pins
Power is supplied to the MCU through VDD and VSS. Because fast signal transitions place high, short-duration current demands on the power supply, use bypass capacitors with high-frequency characteristics and place them as close to the MCU as possible. This 2.5V supply is derived from the internal voltage regulator. There is no static load on those pins allowed. The internal voltage regulator is turned off, if VREGEN is tied to ground.
NOTE:
No load allowed except for bypass capacitors.
2.4.4 VDDA, VSSA -- Power Supply Pins for ATD0/ATD1 and VREG
VDDA, VSSA are the power supply and ground input pins for the voltage regulator and the two analog to digital converters. It also provides the reference for the internal voltage regulator. This allows the supply voltage to ATD0/ATD1 and the reference voltage to be bypassed independently.
61
MC9S12DJ64 Device User Guide -- V01.10
2.4.5 VRH, VRL -- ATD Reference Voltage Input Pins
VRH and VRL are the reference voltage input pins for the analog to digital converter.
2.4.6 VDDPLL, VSSPLL -- Power Supply Pins for PLL
Provides operating voltage and ground for the Oscillator and the Phased-Locked Loop. This allows the supply voltage to the Oscillator and PLL to be bypassed independently.This 2.5V voltage is generated by the internal voltage regulator.
NOTE:
No load allowed except for bypass capacitors.
2.4.7 VREGEN -- On Chip Voltage Regulator Enable
Enables the internal 5V to 2.5V voltage regulator. If this pin is tied low, VDD1,2 and VDDPLL must be supplied externally.
62
MC9S12DJ64 Device User Guide -- V01.10
Section 3 System Clock Description
3.1 Overview
The Clock and Reset Generator provides the internal clock signals for the core and all peripheral modules. Figure 3-1 shows the clock connections from the CRG to all modules. Consult the CRG Block User Guide for details on clock generation.
BDM
S12_CORE core clock
Flash RAM EEPROM EXTAL ECT ATD0, 1 CRG bus clock oscillator clock XTAL PWM SCI0, SCI1 SPI0 CAN0 IIC BDLC PIM
Figure 3-1 Clock Connections
63
MC9S12DJ64 Device User Guide -- V01.10
64
MC9S12DJ64 Device User Guide -- V01.10
Section 4 Modes of Operation
4.1 Overview
Eight possible modes determine the operating configuration of the MC9S12DJ64. Each mode has an associated default memory map and external bus configuration. Three low power modes exist for the device.
4.2 Chip Configuration Summary
The operating mode out of reset is determined by the states of the MODC, MODB, and MODA pins during reset (Table 4-1). The MODC, MODB, and MODA bits in the MODE register show the current operating mode and provide limited mode switching during operation. The states of the MODC, MODB, and MODA pins are latched into these bits on the rising edge of the reset signal. The ROMCTL signal allows the setting of the ROMON bit in the MISC register thus controlling whether the internal Flash is visible in the memory map. ROMON = 1 mean the Flash is visible in the memory map. The state of the ROMCTL pin is latched into the ROMON bit in the MISC register on the rising edge of the reset signal. Table 4-1 Mode Selection
BKGD = MODC
0
PE6 = MODB
0
PE5 = MODA
0
PK7 = ROMCTL
X 0 1 X 0 1 X 0 1 X 0 1
ROMON Bit
1 1 0 0 1 0 1 0 1 1 0 1
Mode Description
Special Single Chip, BDM allowed and ACTIVE. BDM is allowed in all other modes but a serial command is required to make BDM active. Emulation Expanded Narrow, BDM allowed Special Test (Expanded Wide), BDM allowed Emulation Expanded Wide, BDM allowed Normal Single Chip, BDM allowed Normal Expanded Narrow, BDM allowed Peripheral; BDM allowed but bus operations would cause bus conflicts (must not be used) Normal Expanded Wide, BDM allowed
0 0 0 1 1 1 1
0 1 1 0 0 1 1
1 0 1 0 1 0 1
For further explanation on the modes refer to the Core User Guide.
Table 4-2 Clock Selection Based on PE7
PE7 = XCLKS
1
Description
Colpitts Oscillator selected
65
MC9S12DJ64 Device User Guide -- V01.10
Table 4-2 Clock Selection Based on PE7
PE7 = XCLKS
0
Description
Pierce Oscillator/external clock selected
Table 4-3 Voltage Regulator VREGEN
VREGEN
1 0
Description
Internal Voltage Regulator enabled Internal Voltage Regulator disabled, VDD1,2 and VDDPLL must be supplied externally with 2.5V
4.3 Security
The device will make available a security feature preventing the unauthorized read and write of the memory contents. This feature allows: * * * * Protection of the contents of FLASH, Protection of the contents of EEPROM, Operation in single-chip mode, Operation from external memory with internal FLASH and EEPROM disabled.
The user must be reminded that part of the security must lie with the user's code. An extreme example would be user's code that dumps the contents of the internal program. This code would defeat the purpose of security. At the same time the user may also wish to put a back door in the user's program. An example of this is the user downloads a key through the SCI which allows access to a programming routine that updates parameters stored in EEPROM.
4.3.1 Securing the Microcontroller
Once the user has programmed the FLASH and EEPROM (if desired), the part can be secured by programming the security bits located in the FLASH module. These non-volatile bits will keep the part secured through resetting the part and through powering down the part. The security byte resides in a portion of the Flash array. Check the Flash Block User Guide for more details on the security configuration.
4.3.2 Operation of the Secured Microcontroller
4.3.2.1 Normal Single Chip Mode This will be the most common usage of the secured part. Everything will appear the same as if the part was not secured with the exception of BDM operation. The BDM operation will be blocked.
66
MC9S12DJ64 Device User Guide -- V01.10
4.3.2.2 Executing from External Memory The user may wish to execute from external space with a secured microcontroller. This is accomplished by resetting directly into expanded mode. The internal FLASH and EEPROM will be disabled. BDM operations will be blocked.
4.3.3 Unsecuring the Microcontroller
In order to unsecure the microcontroller, the internal FLASH and EEPROM must be erased. This can be done through an external program in expanded mode. Once the user has erased the FLASH and EEPROM, the part can be reset into special single chip mode. This invokes a program that verifies the erasure of the internal FLASH and EEPROM. Once this program completes, the user can erase and program the FLASH security bits to the unsecured state. This is generally done through the BDM, but the user could also change to expanded mode (by writing the mode bits through the BDM) and jumping to an external program (again through BDM commands). Note that if the part goes through a reset before the security bits are reprogrammed to the unsecure state, the part will be secured again.
4.4 Low Power Modes
The microcontroller features three main low power modes. Consult the respective Block User Guide for information on the module behavior in Stop, Pseudo Stop, and Wait Mode. An important source of information about the clock system is the Clock and Reset Generator User Guide (CRG).
4.4.1 Stop
Executing the CPU STOP instruction stops all clocks and the oscillator thus putting the chip in fully static mode. Wake up from this mode can be done via reset or external interrupts.
4.4.2 Pseudo Stop
This mode is entered by executing the CPU STOP instruction. In this mode the oscillator is still running and the Real Time Interrupt (RTI) or Watchdog (COP) sub module can stay active. Other peripherals are turned off. This mode consumes more current than the full STOP mode, but the wake up time from this mode is significantly shorter.
4.4.3 Wait
This mode is entered by executing the CPU WAI instruction. In this mode the CPU will not execute instructions. The internal CPU signals (address and databus) will be fully static. All peripherals stay active. For further power consumption the peripherals can individually turn off their local clocks.
67
MC9S12DJ64 Device User Guide -- V01.10
4.4.4 Run
Although this is not a low power mode, unused peripheral modules should not be enabled in order to save power.
68
MC9S12DJ64 Device User Guide -- V01.10
Section 5 Resets and Interrupts
5.1 Overview
Consult the Exception Processing section of the HCS12 Core User Guide for information on resets and interrupts.
5.2 Vectors
5.2.1 Vector Table
Table 5-1 lists interrupt sources and vectors in default order of priority. Table 5-1 Interrupt Vector Locations
Vector Address
$FFFE, $FFFF $FFFC, $FFFD $FFFA, $FFFB $FFF8, $FFF9 $FFF6, $FFF7 $FFF4, $FFF5 $FFF2, $FFF3 $FFF0, $FFF1 $FFEE, $FFEF $FFEC, $FFED $FFEA, $FFEB $FFE8, $FFE9 $FFE6, $FFE7 $FFE4, $FFE5 $FFE2, $FFE3 $FFE0, $FFE1 $FFDE, $FFDF $FFDC, $FFDD $FFDA, $FFDB $FFD8, $FFD9 $FFD6, $FFD7 $FFD4, $FFD5 $FFD2, $FFD3 $FFD0, $FFD1 $FFCE, $FFCF $FFCC, $FFCD
Interrupt Source
Reset Clock Monitor fail reset COP failure reset Unimplemented instruction trap SWI XIRQ IRQ Real Time Interrupt Enhanced Capture Timer channel 0 Enhanced Capture Timer channel 1 Enhanced Capture Timer channel 2 Enhanced Capture Timer channel 3 Enhanced Capture Timer channel 4 Enhanced Capture Timer channel 5 Enhanced Capture Timer channel 6 Enhanced Capture Timer channel 7 Enhanced Capture Timer overflow Pulse accumulator A overflow Pulse accumulator input edge SPI0 SCI0 SCI1 ATD0 ATD1 Port J Port H
CCR Mask
None None None None None X-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit
Local Enable
None PLLCTL (CME, SCME) COP rate select None None None IRQCR (IRQEN) CRGINT (RTIE) TIE (C0I) TIE (C1I) TIE (C2I) TIE (C3I) TIE (C4I) TIE (C5I) TIE (C6I) TIE (C7I) TSRC2 (TOI) PACTL (PAOVI) PACTL (PAI) SPICR1 (SPIE, SPTIE) SCICR2 (TIE, TCIE, RIE, ILIE) SCICR2 (TIE, TCIE, RIE, ILIE) ATDCTL2 (ASCIE) ATDCTL2 (ASCIE) PIEJ (PIEJ7, PIEJ6, PIEJ1, PIEJ0) PIEH (PIEH7-0)
HPRIO Value to Elevate
- - - - - - $F2 $F0 $EE $EC $EA $E8 $E6 $E4 $E2 $E0 $DE $DC $DA $D8 $D6 $D4 $D2 $D0 $CE $CC
69
MC9S12DJ64 Device User Guide -- V01.10
$FFCA, $FFCB $FFC8, $FFC9 $FFC6, $FFC7 $FFC4, $FFC5 $FFC2, $FFC3 $FFC0, $FFC1 $FFBE, $FFBF $FFBC, $FFBD $FFBA, $FFBB $FFB8, $FFB9 $FFB6, $FFB7 $FFB4, $FFB5 $FFB2, $FFB3 $FFB0, $FFB1 $FFAE, $FFAF $FFAC, $FFAD $FFAA, $FFAB $FFA8, $FFA9 $FFA6, $FFA7 $FFA4, $FFA5 $FFA2, $FFA3 $FFA0, $FFA1 $FF9E, $FF9F $FF9C, $FF9D $FF9A, $FF9B $FF98, $FF99 $FF96, $FF97 $FF94, $FF95 $FF92, $FF93 $FF90, $FF91 $FF8E, $FF8F $FF8C, $FF8D $FF80 to $FF8B Port P PWM Emergency Shutdown Reserved Modulus Down Counter underflow Pulse Accumulator B Overflow CRG PLL lock CRG Self Clock Mode BDLC IIC Bus Reserved EEPROM FLASH CAN0 wake-up CAN0 errors CAN0 receive CAN0 transmit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit I-Bit Reserved PIEP (PIEP7-0) PWMSDN (PWMIE) Reserved MCCTL (MCZI) PBCTL (PBOVI) CRGINT (LOCKIE) CRGINT (SCMIE) DLCBCR1 (IE) IBCR (IBIE) Reserved ECNFG (CCIE, CBEIE) FCNFG (CCIE, CBEIE) CANRIER (WUPIE) CANRIER (CSCIE, OVRIE) CANRIER (RXFIE) CANTIER (TXEIE2-TXEIE0) $CA $C8 $C6 $C4 $C2 $C0 $BE $BC $BA $B8 $B6 $B4 $B2 $B0 $AE $AC $AA $A8 $A6 $A4 $A2 $A0 $9E $9C $9A $98 $96 $94 $92 $90 $8E $8C
5.3 Effects of Reset
When a reset occurs, MCU registers and control bits are changed to known start-up states. Refer to the respective module Block User Guides for register reset states.
5.3.1 I/O pins
Refer to the HCS12 Core User Guides for mode dependent pin configuration of port A, B, E and K out of reset. Refer to the PIM Block User Guide for reset configurations of all peripheral module ports.
70
MC9S12DJ64 Device User Guide -- V01.10
NOTE:
For devices assembled in 80-pin QFP packages all non-bonded out pins should be configured as outputs after reset in order to avoid current drawn from floating inputs. Refer to Table 2-1 for affected pins.
5.3.2 Memory
Refer to Table 1-1 for locations of the memories depending on the operating mode after reset. The RAM array is not automatically initialized out of reset.
71
MC9S12DJ64 Device User Guide -- V01.10
72
MC9S12DJ64 Device User Guide -- V01.10
Section 6 HCS12 Core Block Description
Consult the HCS12 Core User Guide for information about the HCS12 core modules, i.e. central processing unit (CPU), interrupt module (INT), module mapping control module (MMC), multiplexed external bus interface (MEBI), breakpoint module (BKP) and background debug mode module (BDM).
6.1 Device-specific information
When the BDM section of S12 Core User Guide refers to alternate clock this is equivalent to oscillator clock.
Section 7 Clock and Reset Generator (CRG) Block Description
Consult the CRG Block User Guide for information about the Clock and Reset Generator module.
7.1 Device-specific information
The Low Voltage Reset feature of the CRG is not available on this device.
Section 8 Oscillator (OSC) Block Description
Consult the OSC Block User Guide for information about the Oscillator module.
8.1 Device-specific information
The XCLKS input signal is active low (see 2.3.13 PE7 / NOACC / XCLKS -- Port E I/O Pin 7).
Section 9 Enhanced Capture Timer (ECT) Block Description
Consult the ECT_16B8C Block User Guide for information about the Enhanced Capture Timer module. When the ECT_16B8C Block User Guide refers to freeze mode this is equivalent to active BDM mode.
Section 10 Analog to Digital Converter (ATD) Block Description
73
MC9S12DJ64 Device User Guide -- V01.10
There are two Analog to Digital Converters (ATD1 and ATD0) implemented on the MC9S12DJ64. Consult the ATD_10B8C Block User Guide for information about each Analog to Digital Converter module. When the ATD_10B8C Block User Guide refers to freeze mode this is equivalent to active BDM mode.
Section 11 Inter-IC Bus (IIC) Block Description
Consult the IIC Block User Guide for information about the Inter-IC Bus module.
Section 12 Serial Communications Interface (SCI) Block Description
There are two Serial Communications Interfaces (SCI1 and SCI0) implemented on the MC9S12DJ64 device. Consult the SCI Block User Guide for information about each Serial Communications Interface module.
Section 13 Serial Peripheral Interface (SPI) Block Description
Consult the SPI Block User Guide for information about each Serial Peripheral Interface module.
Section 14 J1850 (BDLC) Block Description
Consult the BDLC Block User Guide for information about the J1850 module.
Section 15 Pulse Width Modulator (PWM) Block Description
Consult the PWM_8B8C Block User Guide for information about the Pulse Width Modulator module. When the PWM_8B8C Block User Guide refers to freeze mode this is equivalent to active BDM mode.
Section 16 Flash EEPROM 64K Block Description
Consult the FTS64K Block User Guide for information about the flash module.
Section 17 EEPROM 1K Block Description
74
MC9S12DJ64 Device User Guide -- V01.10
Consult the EETS1K Block User Guide for information about the EEPROM module.
Section 18 RAM Block Description
This module supports single-cycle misaligned word accesses.
Section 19 MSCAN Block Description
Consult the MSCAN Block User Guide for information about the Motorola Scalable CAN Module.
Section 20 Port Integration Module (PIM) Block Description
Consult the PIM_9DJ64 Block User Guide for information about the Port Integration Module.
Section 21 Voltage Regulator (VREG) Block Description
Consult the VREG Block User Guide for information about the dual output linear voltage regulator.
Section 22 Printed Circuit Board Layout Proposals
75
MC9S12DJ64 Device User Guide -- V01.10
Table 22-1 Suggested External Component Values
Component
C1 C2 C3 C4 C5 C6 C7 C8 C9 / CS C10 / CP C11 / CDC R1 R2 / RB R3 / RS Q1
Purpose
VDD1 filter cap VDD2 filter cap VDDA filter cap VDDR filter cap VDDPLL filter cap VDDX filter cap OSC load cap OSC load cap PLL loop filter cap
Type
ceramic X7R ceramic X7R ceramic X7R X7R/tantalum ceramic X7R X7R/tantalum
Value
100 .. 220nF 100 .. 220nF 100nF >=100nF 100nF >=100nF
See PLL specification chapter PLL loop filter cap DC cutoff cap PLL loop filter res PLL loop filter res Pierce mode only PLL loop filter res Quartz Colpitts mode only, if recommended by quartz manufacturer See PLL specification chapter
The PCB must be carefully laid out to ensure proper operation of the voltage regulator as well as of the MCU itself. The following rules must be observed: * * * * * * * Every supply pair must be decoupled by a ceramic capacitor connected as near as possible to the corresponding pins(C1 - C6). Central point of the ground star should be the VSSR pin. Use low ohmic low inductance connections between VSS1, VSS2 and VSSR. VSSPLL must be directly connected to VSSR. Keep traces of VSSPLL, EXTAL and XTAL as short as possible and occupied board area for C7, C8, C11 and Q1 as small as possible. Do not place other signals or supplies underneath area occupied by C7, C8, C10 and Q1 and the connection area to the MCU. Central power input should be fed in at the VDDA/VSSA pins.
76
MC9S12DJ64 Device User Guide -- V01.10
Figure 22-1 Recommended PCB Layout 112LQFP Colpitts Oscillator
VDDX
VREGEN
C6 VSSX
VSSA
C3
VDDA
VDD1 C1 VSS1 VSS2 C2 VDD2
VSSR C4 VDDR C5 C9 R1 C10 C8 Q1 VSSPLL VDDPLL C7 C11
77
MC9S12DJ64 Device User Guide -- V01.10
Figure 22-2 Recommended PCB Layout for 80QFP Colpitts Oscillator
VDDX
C6
VREGEN
VSSX
VSSA
C3
VDDA
VDD1 VSS2
C1 C2
VSS1 VDD2
VSSR C4 C5 VDDR C11
C8
C7 Q1
C10
R1
C9
VSSPLL VDDPLL
78
MC9S12DJ64 Device User Guide -- V01.10
Figure 22-3 Recommended PCB Layout for 112LQFP Pierce Oscillator
VREGEN VDDX C6 VSSX
VSSA
C3
VDDA
VDD1 C1 VSS1 VSS2 C2 VDD2
VSSR R3 C5 R2 Q1 C9 C10 C8 C7 VSSPLL C4 VDDR VDDPLL R1
79
MC9S12DJ64 Device User Guide -- V01.10
Figure 22-4 Recommended PCB Layout for 80QFP Pierce Oscillator
VDDX
C6
VREGEN
VSSX
VSSA
C3
VDDA
VDD1 VSS2
C1 C2
VSS1 VDD2
VSSPLL
VSSR C4 C5 VDDR
R2 Q1 C8 C7 R3
C10
R1
C9
VSSPLL VDDPLL
80
MC9S12DJ64 Device User Guide -- V01.10
Appendix A Electrical Characteristics
A.1 General
This introduction is intended to give an overview on several common topics like power supply, current injection etc.
A.1.1 Parameter Classification
The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better understanding the following classification is used and the parameters are tagged accordingly in the tables where appropriate.
NOTE:
P:
This classification is shown in the column labeled "C" in the parameter tables where appropriate.
Those parameters are guaranteed during production testing on each individual device. C: Those parameters are achieved by the design characterization by measuring a statistically relevant sample size across process variations. T: Those parameters are achieved by design characterization on a small sample size from typical devices under typical conditions unless otherwise noted. All values shown in the typical column are within this category. D: Those parameters are derived mainly from simulations.
A.1.2 Power Supply
The MC9S12DJ64 utilizes several pins to supply power to the I/O ports, A/D converter, oscillator and PLL as well as the digital core. The VDDA, VSSA pair supplies the A/D converter and the resistor ladder of the internal voltage regulator. The VDDX, VSSX, VDDR and VSSR pairs supply the I/O pins, VDDR supplies also the internal voltage regulator. VDD1, VSS1, VDD2 and VSS2 are the supply pins for the digital logic, VDDPLL, VSSPLL supply the oscillator and the PLL. VSS1 and VSS2 are internally connected by metal.
81
MC9S12DJ64 Device User Guide -- V01.10
VDDA, VDDX, VDDR as well as VSSA, VSSX, VSSR are connected by anti-parallel diodes for ESD protection.
NOTE:
In the following context VDD5 is used for either VDDA, VDDR and VDDX; VSS5 is used for either VSSA, VSSR and VSSX unless otherwise noted. IDD5 denotes the sum of the currents flowing into the VDDA, VDDX and VDDR pins. VDD is used for VDD1, VDD2 and VDDPLL, VSS is used for VSS1, VSS2 and VSSPLL. IDD is used for the sum of the currents flowing into VDD1 and VDD2.
A.1.3 Pins
There are four groups of functional pins. A.1.3.1 5V I/O pins Those I/O pins have a nominal level of 5V. This class of pins is comprised of all port I/O pins, the analog inputs, BKGD and the RESET pins.The internal structure of all those pins is identical, however some of the functionality may be disabled. E.g. for the analog inputs the output drivers, pull-up and pull-down resistors are disabled permanently. A.1.3.2 Analog Reference This group is made up by the VRH and VRL pins. A.1.3.3 Oscillator The pins XFC, EXTAL, XTAL dedicated to the oscillator have a nominal 2.5V level. They are supplied by VDDPLL. A.1.3.4 TEST This pin is used for production testing only. A.1.3.5 VREGEN This pin is used to enable the on chip voltage regulator.
A.1.4 Current Injection
Power supply must maintain regulation within operating VDD5 or VDD range during instantaneous and operating maximum current conditions. If positive injection current (Vin > VDD5) is greater than IDD5, the injection current may flow out of VDD5 and could result in external power supply going out of regulation. Ensure external VDD5 load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power; e.g. if no system clock is present, or if clock rate is very low which would reduce overall power consumption.
82
MC9S12DJ64 Device User Guide -- V01.10
A.1.5 Absolute Maximum Ratings
Absolute maximum ratings are stress ratings only. A functional operation under or outside those maxima is not guaranteed. Stress beyond those limits may affect the reliability or cause permanent damage of the device. This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (e.g., either VSS5 or VDD5). Table A-1 Absolute Maximum Ratings1
Num
1 2 3 4 5 6 7 8 9 10 11 12 13
Rating
I/O, Regulator and Analog Supply Voltage Digital Logic Supply Voltage 2 PLL Supply Voltage 2 Voltage difference VDDX to VDDR and VDDA Voltage difference VSSX to VSSR and VSSA Digital I/O Input Voltage Analog Reference XFC, EXTAL, XTAL inputs TEST input Instantaneous Maximum Current Single pin limit for all digital I/O pins 3 Instantaneous Maximum Current Single pin limit for XFC, EXTAL, XTAL4 Instantaneous Maximum Current Single pin limit for TEST 5 Storage Temperature Range
Symbol
VDD5 VDD VDDPLL VDDX VSSX VIN VRH, VRL VILV VTEST ID I
Min
-0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -25 -25 -0.25 - 65
Max
6.0 3.0 3.0 0.3 0.3 6.0 6.0 3.0 10.0 +25 +25 0 155
Unit
V V V V V V V V V mA mA mA C
DL
IDT T
stg
NOTES: 1. Beyond absolute maximum ratings device might be damaged. 2. The device contains an internal voltage regulator to generate the logic and PLL supply out of the I/O supply. The absolute maximum ratings apply when the device is powered from an external source. 3. All digital I/O pins are internally clamped to VSSX and VDDX, VSSR and VDDR or VSSA and VDDA. 4. Those pins are internally clamped to VSSPLL and VDDPLL. 5. This pin is clamped low to VSSPLL, but not clamped high. This pin must be tied low in applications.
83
MC9S12DJ64 Device User Guide -- V01.10
A.1.6 ESD Protection and Latch-up Immunity
All ESD testing is in conformity with CDF-AEC-Q100 Stress test qualification for Automotive Grade Integrated Circuits. During the device qualification ESD stresses were performed for the Human Body Model (HBM), the Machine Model (MM) and the Charge Device Model. A device will be defined as a failure if after exposure to ESD pulses the device no longer meets the device specification. Complete DC parametric and functional testing is performed per the applicable device specification at room temperature followed by hot temperature, unless specified otherwise in the device specification. Table A-2 ESD and Latch-up Test Conditions
Model
Series Resistance Storage Capacitance Human Body Number of Pulse per pin positive negative Series Resistance Storage Capacitance Machine Number of Pulse per pin positive negative Minimum input voltage limit Latch-up Maximum input voltage limit 7.5 V
Description
Symbol
R1 C R1 C -
Value
1500 100 1 1 0 200 3 3 -2.5
Unit
Ohm pF
Ohm pF
V
Table A-3 ESD and Latch-Up Protection Characteristics
Num C
1 2 3 4
Rating
Symbol
VHBM VMM VCDM ILAT
Min
2000 200 500 +100 -100 +200 -200
Max
-
Unit
V V V mA
T Human Body Model (HBM) T Machine Model (MM) T Charge Device Model (CDM) Latch-up Current at TA = 125C T positive negative Latch-up Current at TA = 27C T positive negative
5
ILAT
-
mA
A.1.7 Operating Conditions
This chapter describes the operating conditions of the device. Unless otherwise noted those conditions apply to all the following data.
84
MC9S12DJ64 Device User Guide -- V01.10
NOTE:
Please refer to the temperature rating of the device (C, V, M) with regards to the ambient temperature TA and the junction temperature TJ. For power dissipation calculations refer to Section A.1.8 Power Dissipation and Thermal Characteristics. Table A-4 Operating Conditions
Rating Symbol
VDD5 VDD VDDPLL VDDX VSSX fosc fbus
Min
4.5 2.35 2.35 -0.1 -0.1 0.5 0.5
Typ
5 2.5 2.5 0 0 -
Max
5.25 2.75 2.75 0.1 0.1 16 25
Unit
V V V V V MHz MHz
I/O, Regulator and Analog Supply Voltage Digital Logic Supply Voltage 1 PLL Supply Voltage 2 Voltage Difference VDDX to VDDR and VDDA Voltage Difference VSSX to VSSR and VSSA Oscillator Bus Frequency MC9S12DJ64C Operating Junction Temperature Range Operating Ambient Temperature Range 2 MC9S12DJ64V Operating Junction Temperature Range Operating Ambient Temperature Range 2 MC9S12DJ64M Operating Junction Temperature Range Operating Ambient Temperature Range 2
TJ T
A
-40 -40
27
100 85
C C
T
J
-40 -40
27
120 105
C C
TA
TJ TA
-40 -40
27
140 125
C C
NOTES: 1. The device contains an internal voltage regulator to generate the logic and PLL supply out of the I/O supply. The absolute maximum ratings apply when this regulator is disabled and the device is powered from an external source. 2. Please refer to Section A.1.8 Power Dissipation and Thermal Characteristics for more details about the relation between ambient temperature TA and device junction temperature TJ.
A.1.8 Power Dissipation and Thermal Characteristics
Power dissipation and thermal characteristics are closely related. The user must assure that the maximum operating junction temperature is not exceeded. The average chip-junction temperature (TJ) in C can be obtained from: T J = T A + ( P D * JA ) T J = Junction Temperature, [C ] T A = Ambient Temperature, [C ]
85
MC9S12DJ64 Device User Guide -- V01.10
P D = Total Chip Power Dissipation, [W] JA = Package Thermal Resistance, [C/W] The total power dissipation can be calculated from: P D = P INT + P IO P INT = Chip Internal Power Dissipation, [W]
Two cases with internal voltage regulator enabled and disabled must be considered: 1. Internal Voltage Regulator disabled P INT = I DD V DD + I DDPLL V DDPLL + I DDA V DDA 2 P IO = R DSON I IO i i
PIO is the sum of all output currents on I/O ports associated with VDDX and VDDR. For RDSON is valid: V OL R DSON = ----------- ;for outputs driven low I OL
V DD5 - V OH R DSON = ----------------------------------- ;for outputs driven high I OH 2. Internal voltage regulator enabled P INT = I DDR V DDR + I DDA V DDA IDDR is the current shown in Table A-7 and not the overall current flowing into VDDR, which additionally contains the current flowing into the external loads with output high. 2 P IO = R DSON I IO i i
respectively
PIO is the sum of all output currents on I/O ports associated with VDDX and VDDR.
86
MC9S12DJ64 Device User Guide -- V01.10
Table A-5 Thermal Package Characteristics1
Num C
1 2 3 4 5 6 7 8 9 10
Rating
Symbol
JA JA JB JC JT JA JA JB JC JT
Min
- - - - - - - - - -
Typ
- - - - - - - - - -
Max
54 41 31 11 2 51 41 27 14 3
Unit
o
T Thermal Resistance LQFP112, single sided PCB2 T Thermal Resistance LQFP112, double sided PCB with 2 internal planes3
C/W C/W
o
T Junction to Board LQFP112 T Junction to Case LQFP112 T Junction to Package Top LQFP112 T Thermal Resistance QFP 80, single sided PCB T Thermal Resistance QFP 80, double sided PCB with 2 internal planes
oC/W o o o
C/W C/W C/W
oC/W oC/W oC/W oC/W
T Junction to Board QFP80 T Junction to Case QFP80 T Junction to Package Top QFP80
NOTES: 1. The values for thermal resistance are achieved by package simulations 2. PC Board according to EIA/JEDEC Standard 51-3 3. PC Board according to EIA/JEDEC Standard 51-7
A.1.9 I/O Characteristics
This section describes the characteristics of all 5V I/O pins. All parameters are not always applicable, e.g. not all pins feature pull up/down resistances.
87
MC9S12DJ64 Device User Guide -- V01.10
Table A-6 5V I/O Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1 2 3 P Input High Voltage P Input Low Voltage C Input Hysteresis
Rating
Symbol
V
IH IL
Min
0.65*VDD5 VSS5 - 0.3
Typ
250
Max
VDD5 + 0.3 0.35*VDD5
Unit
V V mV A
V V
HYS
4
Input Leakage Current (pins in high impedance input P mode) V =V or VSS5 in DD5 Output High Voltage (pins in output mode) P Partial Drive IOH = -2mA Full Drive IOH = -10mA Output Low Voltage (pins in output mode) P Partial Drive IOL = +2mA Full Drive IOL = +10mA Internal Pull Up Device Current, P tested at V Max.
IL
Iin
-1
-
1
5
V
OH
VDD5 - 0.8
-
-
V
6
V
OL
-
-
0.8
V
7
IPUL IPUH IPDH IPDL Cin IICS IICP tpign tpval
-
-
-130
A A A A pF mA s s
8
Internal Pull Up Device Current, C tested at V Min.
IH
-10
-
-
9
Internal Pull Down Device Current, P tested at V Min.
IH
-
-
130
10 11 12
Internal Pull Down Device Current, C tested at V Max.
IL
10
6
2.5 25 3
D Input Capacitance Injection current1 T Single Pin limit Total Device Limit. Sum of all injected currents P Port H, J, P Interrupt Input Pulse filtered2 P Port H, J, P Interrupt Input Pulse passed2
-2.5 -25
-
13 14
10
NOTES: 1. Refer to Section A.1.4 Current Injection, for more details 2. Parameter only applies in STOP or Pseudo STOP mode.
A.1.10 Supply Currents
This section describes the current consumption characteristics of the device as well as the conditions for the measurements.
88
MC9S12DJ64 Device User Guide -- V01.10
A.1.10.1 Measurement Conditions All measurements are without output loads. Unless otherwise noted the currents are measured in single chip mode, internal voltage regulator enabled and at 25MHz bus frequency using a 4MHz oscillator in Colpitts mode. Production testing is performed using a square wave signal at the EXTAL input. A.1.10.2 Additional Remarks In expanded modes the currents flowing in the system are highly dependent on the load at the address, data and control signals as well as on the duty cycle of those signals. No generally applicable numbers can be given. A very good estimate is to take the single chip currents and add the currents due to the external loads. Table A-7 Supply Current Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1 P
Rating
Run supply currents Single Chip, Internal regulator enabled Wait Supply current All modules enabled, PLL on only RTI enabled 1 Pseudo Stop Current (RTI and COP enabled) 1, 2 -40C 27C 70C 85C "C" Temp Option 100C 105C "V" Temp Option 120C 125C "M" Temp Option 140C Pseudo Stop Current (RTI and COP disabled) 1, 2 -40C 27C 70C 85C 105C 125C 140C Stop Current 2 -40C 27C 70C 85C "C" Temp Option 100C 105C "V" Temp Option 120C 125C "M" Temp Option 140C
Symbol
IDD5 IDDW
Min
Typ
Max
50 30 5
Unit
mA
2
P P C P C C P C P C P C C C C C C C C P C C P C P C P
mA
3
IDDPS
370 400 450 550 600 650 800 850 1200 570 600 650 750 850 1200 1500 12 25 100 130 160 200 350 400 600
500 A
1600 2100 5000
4
IDDPS
A
100 A
5
IDDS
1200 1700 5000
89
MC9S12DJ64 Device User Guide -- V01.10
NOTES: 1. PLL off 2. At those low power dissipation levels TJ = TA can be assumed
90
MC9S12DJ64 Device User Guide -- V01.10
A.2 ATD Characteristics
This section describes the characteristics of the analog to digital converter.
A.2.1 ATD Operating Characteristics
The Table A-8 shows conditions under which the ATD operates. The following constraints exist to obtain full-scale, full range results: VSSA VRL VIN VRH VDDA. This constraint exists since the sample buffer amplifier can not drive beyond the power supply levels that it ties to. If the input level goes outside of this range it will effectively be clipped. Table A-8 ATD Operating Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
Reference Potential 1 2 3 4 D
Rating
Low High
Symbol VRL VRH VRH-VRL fATDCLK
Min VSSA VDDA/2 4.50 0.5 14 7 12 6
Typ
Max VDDA/2 VDDA
Unit V V V MHz Cycles s Cycles s s mA mA
C Differential Reference Voltage1 D ATD Clock Frequency ATD 10-Bit Conversion Period D
5.00
5.25 2.0 28 14 26 13 20 0.750 0.375
Clock Cycles2 NCONV10 Conv, Time at 2.0MHz ATD Clock fATDCLK TCONV10 ATD 8-Bit Conversion Period Clock Cycles2 Conv, Time at 2.0MHz ATD Clock fATDCLK
5
D
NCONV8 TCONV8 tREC IREF IREF
6 7 8
D Recovery Time (VDDA=5.0 Volts) P Reference Supply current 2 ATD blocks on P Reference Supply current 1 ATD block on
NOTES: 1. Full accuracy is not guaranteed when differential voltage is less than 4.50V 2. The minimum time assumes a final sample period of 2 ATD clocks cycles while the maximum time assumes a final sample period of 16 ATD clocks.
A.2.2 Factors influencing accuracy
Three factors - source resistance, source capacitance and current injection - have an influence on the accuracy of the ATD. A.2.2.1 Source Resistance: Due to the input pin leakage current as specified in Table A-6 in conjunction with the source resistance there will be a voltage drop from the signal source to the ATD input. The maximum source resistance RS
91
MC9S12DJ64 Device User Guide -- V01.10
specifies results in an error of less than 1/2 LSB (2.5mV) at the maximum leakage current. If device or operating conditions are less than worst case or leakage-induced error is acceptable, larger values of source resistance is allowed. A.2.2.2 Source Capacitance When sampling an additional internal capacitor is switched to the input. This can cause a voltage drop due to charge sharing with the external and the pin capacitance. For a maximum sampling error of the input voltage 1LSB, then the external filter capacitor, Cf 1024 * (CINS- CINN). A.2.2.3 Current Injection There are two cases to consider. 1. A current is injected into the channel being converted. The channel being stressed has conversion values of $3FF ($FF in 8-bit mode) for analog inputs greater than VRH and $000 for values less than VRL unless the current is higher than specified as disruptive condition. 2. Current is injected into pins in the neighborhood of the channel being converted. A portion of this current is picked up by the channel (coupling ratio K), This additional current impacts the accuracy of the conversion depending on the source resistance. The additional input voltage error on the converted channel can be calculated as VERR = K * RS * IINJ, with IINJ being the sum of the currents injected into the two pins adjacent to the converted channel. Table A-9 ATD Electrical Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1 2 3 4 5
Rating
Symbol
RS CINN CINS INA Kp Kn
Min
-
Typ
-
Max
1 10 22
Unit
K pF mA A/A A/A
C Max input Source Resistance Total Input Capacitance T Non Sampling Sampling C Disruptive Analog Input Current C Coupling Ratio positive current injection C Coupling Ratio negative current injection
-2.5
2.5 10-4 10-2
92
MC9S12DJ64 Device User Guide -- V01.10
A.2.3 ATD accuracy
Table A-10 specifies the ATD conversion performance excluding any errors due to current injection, input capacitance and source resistance. Table A-10 ATD Conversion Performance
Conditions are shown in Table A-4 unless otherwise noted VREF = VRH - VRL = 5.12V. Resulting to one 8 bit count = 20mV and one 10 bit count = 5mV
fATDCLK = 2.0MHz Num C
1 2 3 4 5 6 7 8 P 10-Bit Resolution P 10-Bit Differential Nonlinearity P 10-Bit Integral Nonlinearity P 10-Bit Absolute Error1 P 8-Bit Resolution P 8-Bit Differential Nonlinearity P 8-Bit Integral Nonlinearity P 8-Bit Absolute Error1
Rating
Symbol
LSB DNL INL AE LSB DNL INL AE
Min
Typ
5
Max
Unit
mV
-1 -2.5 -3 1.5 2.0 20 -0.5 -1.0 -1.5 0.5 1.0
1 2.5 3
Counts Counts Counts mV
0.5 1.0 1.5
Counts Counts Counts
NOTES: 1. These values include the quantization error which is inherently 1/2 count for any A/D converter.
For the following definitions see also Figure A-1. Differential Non-Linearity (DNL) is defined as the difference between two adjacent switching steps.
Vi - Vi - 1 DNL ( i ) = ----------------------- - 1 1LSB
The Integral Non-Linearity (INL) is defined as the sum of all DNLs: n
INL ( n ) =
i=1
Vn - V0 DNL ( i ) = ------------------- - n 1LSB
93
MC9S12DJ64 Device User Guide -- V01.10
DNL
LSB Vi-1
$3FF $3FE $3FD $3FC $3FB $3FA $3F9 $3F8 $3F7 $3F6 $3F5
10-Bit Absolute Error Boundary Vi 8-Bit Absolute Error Boundary
$FF
$FE
10-Bit Resolution
$3F4 $3F3
$FD
9 8 7 6 5 4 3 2 1 0 5 10 15 20 25 30 35 40 45
Ideal Transfer Curve
2
10-Bit Transfer Curve
1
8-Bit Transfer Curve
5055 5060 5065 5070 5075 5080 5085 5090 5095 5100 5105 5110 5115 5120
Vin mV
Figure A-1 ATD Accuracy Definitions
NOTE:
Figure A-1 shows only definitions, for specification values refer to Table A-10.
94
8-Bit Resolution
MC9S12DJ64 Device User Guide -- V01.10
A.3 NVM, Flash and EEPROM
NOTE:
Unless otherwise noted the abbreviation NVM (Non Volatile Memory) is used for both Flash and EEPROM.
A.3.1 NVM timing
The time base for all NVM program or erase operations is derived from the oscillator. A minimum oscillator frequency fNVMOSC is required for performing program or erase operations. The NVM modules do not have any means to monitor the frequency and will not prevent program or erase operation at frequencies above or below the specified minimum. Attempting to program or erase the NVM modules at a lower frequency a full program or erase transition is not assured. The Flash and EEPROM program and erase operations are timed using a clock derived from the oscillator using the FCLKDIV and ECLKDIV registers respectively. The frequency of this clock must be set within the limits specified as fNVMOP. The minimum program and erase times shown in Table A-11 are calculated for maximum fNVMOP and maximum fbus. The maximum times are calculated for minimum fNVMOP and a fbus of 2MHz.
A.3.1.1 Single Word Programming The programming time for single word programming is dependant on the bus frequency as a well as on the frequency fNVMOP and can be calculated according to the following formula.
1 1 t swpgm = 9 --------------------- + 25 ---------f NVMOP f bus
A.3.1.2 Burst Programming This applies only to the Flash where up to 32 words in a row can be programmed consecutively using burst programming by keeping the command pipeline filled. The time to program a consecutive word can be calculated as:
1 1 t bwpgm = 4 --------------------- + 9 ---------f NVMOP f bus
The time to program a whole row is:
t brpgm = t swpgm + 31 t bwpgm
Burst programming is more than 2 times faster than single word programming.
95
MC9S12DJ64 Device User Guide -- V01.10
A.3.1.3 Sector Erase Erasing a 512 byte Flash sector or a 4 byte EEPROM sector takes:
1 t era 4000 --------------------f NVMOP
The setup time can be ignored for this operation. A.3.1.4 Mass Erase Erasing a NVM block takes:
1 t mass 20000 --------------------f NVMOP
The setup time can be ignored for this operation. A.3.1.5 Blank Check The time it takes to perform a blank check on the Flash or EEPROM is dependant on the location of the first non-blank word starting at relative address zero. It takes one bus cycle per word to verify plus a setup of the command.
t check location t cyc + 10 t cyc
Table A-11 NVM Timing Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1 2 3 4 5 6 7 8 9 10
Rating
Symbol
fNVMOSC fNVMBUS fNVMOP tswpgm tbwpgm tbrpgm tera tmass tcheck tcheck
Min
0.5 1 150 46 2 20.4 2 678.4 2 20 5 100 5 11 6 11 6
Typ
Max
50 1
Unit
MHz MHz
D External Oscillator Clock D Bus frequency for Programming or Erase Operations D Operating Frequency P Single Word Programming Time D Flash Burst Programming consecutive word 4 D Flash Burst Programming Time for 32 Words 4 P Sector Erase Time P Mass Erase Time D Blank Check Time Flash per block D Blank Check Time EEPROM per block
200 74.5 3 31 3 1035.5 3 26.7 3 133 3 32778 7 20587
kHz s s s ms ms tcyc tcyc
NOTES: 1. Restrictions for oscillator in crystal mode apply! 2. Minimum Programming times are achieved under maximum NVM operating frequency fNVMOP and maximum bus frequency fbus.
96
MC9S12DJ64 Device User Guide -- V01.10
3. Maximum Erase and Programming times are achieved under particular combinations of fNVMOP and bus frequency fbus. Refer to formulae in Sections A.3.1.1 - A.3.1.4 for guidance. 4. Burst Programming operations are not applicable to EEPROM 5. Minimum Erase times are achieved under maximum NVM operating frequency fNVMOP. 6. Minimum time, if first word in the array is not blank 7. Maximum time to complete check on an erased block
A.3.2 NVM Reliability
The reliability of the NVM blocks is guaranteed by stress test during qualification, constant process monitors and burn-in to screen early life failures. The failure rates for data retention and program/erase cycling are specified at the operating conditions noted. The program/erase cycle count on the sector is incremented every time a sector or mass erase event is executed. Table A-12 NVM Reliability Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1 2 3 C
Rating
Data Retention at an average junction temperature of TJavg = 70C
Symbol
tNVMRET nFLPE nEEPE nEEPE
Min
15 10,000 10,000
Typ
Max
Unit
Years Cycles Cycles
C Flash number of Program/Erase cycles C EEPROM number of Program/Erase cycles (-40C TJ 0C) EEPROM number of Program/Erase cycles (0C < TJ 140C)
4
C
100,000
Cycles
97
MC9S12DJ64 Device User Guide -- V01.10
98
MC9S12DJ64 Device User Guide -- V01.10
A.4 Voltage Regulator
The on-chip voltage regulator is intended to supply the internal logic and oscillator circuits. No external DC load is allowed. Table A-13 Voltage Regulator Recommended Load Capacitances
Rating
Load Capacitance on VDD1, 2 Load Capacitance on VDDPLL
Symbol
CLVDD CLVDDfcPLL
Min
Typ
220 220
Max
Unit
nF nF
99
MC9S12DJ64 Device User Guide -- V01.10
100
MC9S12DJ64 Device User Guide -- V01.10
A.5 Reset, Oscillator and PLL
This section summarizes the electrical characteristics of the various startup scenarios for Oscillator and Phase-Locked-Loop (PLL).
A.5.1 Startup
Table A-14 summarizes several startup characteristics explained in this section. Detailed description of the startup behavior can be found in the Clock and Reset Generator (CRG) Block User Guide.
Table A-14 Startup Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1 2 3 4 5 6 T POR release level T POR assert level
Rating
Symbol
VPORR VPORA PWRSTL nRST PWIRQ tWRS
Min
Typ
Max
2.07
Unit
V V tosc
0.97 2 192 20 14 196
D Reset input pulse width, minimum input time D Startup from Reset D Interrupt pulse width, IRQ edge-sensitive mode D Wait recovery startup time
nosc ns tcyc
A.5.1.1 POR The release level VPORR and the assert level VPORA are derived from the VDD Supply. They are also valid if the device is powered externally. After releasing the POR reset the oscillator and the clock quality check are started. If after a time tCQOUT no valid oscillation is detected, the MCU will start using the internal self clock. The fastest startup time possible is given by nuposc. A.5.1.2 SRAM Data Retention Provided an appropriate external reset signal is applied to the MCU, preventing the CPU from executing code when VDD5 is out of specification limits, the SRAM contents integrity is guaranteed if after the reset the PORF bit in the CRG Flags Register has not been set. A.5.1.3 External Reset When external reset is asserted for a time greater than PWRSTL the CRG module generates an internal reset, and the CPU starts fetching the reset vector without doing a clock quality check, if there was an oscillation before reset. A.5.1.4 Stop Recovery Out of STOP the controller can be woken up by an external interrupt. A clock quality check as after POR is performed before releasing the clocks to the system.
101
MC9S12DJ64 Device User Guide -- V01.10
A.5.1.5 Pseudo Stop and Wait Recovery The recovery from Pseudo STOP and Wait are essentially the same since the oscillator was not stopped in both modes. The controller can be woken up by internal or external interrupts. After twrs the CPU starts fetching the interrupt vector.
A.5.2 Oscillator
The device features an internal Colpitts and Pierce oscillator. The selection of Colpitts oscillator or Pierce oscillator/external clock depends on the XCLKS signal which is sampled during reset.By asserting the XCLKS input during reset this oscillator can be bypassed allowing the input of a square wave. Before asserting the oscillator to the internal system clocks the quality of the oscillation is checked for each start from either power-on, STOP or oscillator fail. tCQOUT specifies the maximum time before switching to the internal self clock mode after POR or STOP if a proper oscillation is not detected. The quality check also determines the minimum oscillator start-up time tUPOSC. The device also features a clock monitor. A Clock Monitor Failure is asserted if the frequency of the incoming clock signal is below the Assert Frequency fCMFA. Table A-15 Oscillator Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1a 1b 2 3 4 5 6 7 8 9 10 11 12
Rating
Symbol
fOSC fOSC iOSC tUPOSC tCQOUT fCMFA fEXT tEXTL tEXTH tEXTR tEXTF CIN VDCBIAS
Min
0.5 0.5 100
Typ
Max
16 40
Unit
MHz MHz A
C Crystal oscillator range (Colpitts) C Crystal oscillator range (Pierce) 1 P Startup Current C Oscillator start-up time (Colpitts) D Clock Quality check time-out P Clock Monitor Failure Assert Frequency P External square wave input frequency 4 D External square wave pulse width low D External square wave pulse width high D External square wave rise time D External square wave fall time D Input Capacitance (EXTAL, XTAL pins) C DC Operating Bias in Colpitts Configuration on EXTAL Pin
82 0.45 50 0.5 9.5 9.5 100
1003 2.5 200 50
ms s KHz MHz ns ns
1 1 7 1.1
ns ns pF V
NOTES: 1. Depending on the crystal a damping series resistor might be necessary 2. fosc = 4MHz, C = 22pF. 3. Maximum value is for extreme cases using high Q, low frequency crystals 4. XCLKS =0 during reset
102
MC9S12DJ64 Device User Guide -- V01.10
A.5.3 Phase Locked Loop
The oscillator provides the reference clock for the PLL. The PLLs Voltage Controlled Oscillator (VCO) is also the system clock source in self clock mode. A.5.3.1 XFC Component Selection This section describes the selection of the XFC components to achieve a good filter characteristics.
Cp VDDPLL Cs fosc fref 1 refdv+1 fcmp R Phase K Detector Loop Divider 1 synr+1
XFC Pin
VCO KV fvco
1 2
Figure A-2 Basic PLL functional diagram The following procedure can be used to calculate the resistance and capacitance values using typical values for K1, f1 and ich from Table A-16. The grey boxes show the calculation for fVCO = 50MHz and fref = 1MHz. E.g., these frequencies are used for fOSC = 4MHz and a 25MHz bus clock. The VCO Gain at the desired VCO frequency is approximated by: ( f 1 - f vco ) ---------------------K 1 1V ( 60 - 50 ) ----------------------- 100
KV = K1 e
= - 100 e
= -90.48MHz/V
The phase detector relationship is given by:
K = - i ch K V
ich is the current in tracking mode.
= 316.7Hz/
103
MC9S12DJ64 Device User Guide -- V01.10
The loop bandwidth fC should be chosen to fulfill the Gardner's stability criteria by at least a factor of 10, typical values are 50. = 0.9 ensures a good transient response.
2 f ref f ref 1 f C < ------------------------------------------ ----- f C < ------------- ;( = 0.9 ) 4 10 10 2 + 1 + fC < 25kHz
And finally the frequency relationship is defined as
f VCO n = ------------ = 2 ( synr + 1 ) f ref
= 50
With the above values the resistance can be calculated. The example is shown for a loop bandwidth fC=10kHz:
2 n fC R = ---------------------------- = 2**50*10kHz/(316.7Hz/)=9.9k=~10k K
The capacitance Cs can now be calculated as:
0.516 2 C s = --------------------- -------------- ;( = 0.9 ) = 5.19nF =~ 4.7nF fC R fC R
The capacitance Cp should be chosen in the range of:
2
C s 20 C p C s 10
Cp = 470pF
A.5.3.2 Jitter Information The basic functionality of the PLL is shown in Figure A-2. With each transition of the clock fcmp, the deviation from the reference clock fref is measured and input voltage to the VCO is adjusted accordingly.The adjustment is done continuously with no abrupt changes in the clock output frequency. Noise, voltage, temperature and other factors cause slight variations in the control loop resulting in a clock jitter. This jitter affects the real minimum and maximum clock periods as illustrated in Figure A-3.
104
MC9S12DJ64 Device User Guide -- V01.10
0
1
2
3
N-1
N
tmin1 tnom tmax1 tminN tmaxN
Figure A-3 Jitter Definitions The relative deviation of tnom is at its maximum for one clock period, and decreases towards zero for larger number of clock periods (N). Defining the jitter as:
t min ( N ) t max ( N ) J ( N ) = max 1 - -------------------- , 1 - -------------------- N t nom N t nom
For N < 100, the following equation is a good fit for the maximum jitter:
j1 J ( N ) = ------- + j 2 N
J(N)
1
5
10
20
N
Figure A-4 Maximum bus clock jitter approximation
105
MC9S12DJ64 Device User Guide -- V01.10
This is very important to notice with respect to timers, serial modules where a pre-scaler will eliminate the effect of the jitter to a large extent.
Table A-16 PLL Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Rating
Symbol
fSCM fVCO |trk| |Lock| |unl| |unt| tstab tacq tal K1 f1 | ich | | ich | j1 j2
Min
1 8 3 0 0.5 6
Typ
Max
5.5 50 4 1.5 2.5 8
Unit
MHz MHz %1 %(1) %(1) %(1) ms ms ms MHz/V MHz A A
P Self Clock Mode frequency D VCO locking range D Lock Detector transition from Acquisition to Tracking mode
D Lock Detection D Un-Lock Detection D Lock Detector transition from Tracking to Acquisition mode
C PLLON Total Stabilization delay (Auto Mode) 2 D PLLON Acquisition mode stabilization delay (2) D PLLON Tracking mode stabilization delay (2) D Fitting parameter VCO loop gain D Fitting parameter VCO loop frequency D Charge pump current acquisition mode D Charge pump current tracking mode C Jitter fit parameter 1(2) C Jitter fit parameter 2(2)
0.5 0.3 0.2 -100 60 38.5 3.5 1.1 0.13
% %
NOTES: 1. % deviation from target frequency 2. fOSC = 4MHz, fBUS = 25MHz equivalent fVCO = 50MHz: REFDV = #$03, SYNR = #$018, Cs = 4.7nF, Cp = 470pF, Rs = 10K.
106
MC9S12DJ64 Device User Guide -- V01.10
A.6 MSCAN
Table A-17 MSCAN Wake-up Pulse Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C
1 2
Rating
Symbol
tWUP tWUP
Min
Typ
Max
2
Unit
s s
P MSCAN Wake-up dominant pulse filtered P MSCAN Wake-up dominant pulse pass
5
107
MC9S12DJ64 Device User Guide -- V01.10
108
MC9S12DJ64 Device User Guide -- V01.10
A.7 SPI
A.7.1 Master Mode
Figure A-5 and Figure A-6 illustrate the master mode timing. Timing values are shown in Table A-18.
SS1 (OUTPUT) 2 SCK (CPOL = 0) (OUTPUT) SCK (CPOL = 1) (OUTPUT) 5 MISO (INPUT) 9 MOSI (OUTPUT)
1. If configured as output. 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
1 4 4
11
3
12
6 MSB IN2 BIT 6 . . . 1 9 MSB OUT2 BIT 6 . . . 1 LSB OUT LSB IN 10
Figure A-5 SPI Master Timing (CPHA = 0)
109
MC9S12DJ64 Device User Guide -- V01.10
SS1 (OUTPUT) 1 2 SCK (CPOL = 0) (OUTPUT) 4 SCK (CPOL = 1) (OUTPUT) 5 MISO (INPUT) 9 MOSI (OUTPUT) PORT DATA
1. If configured as output 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
12
11
3
4
11
12
6 MSB IN2 BIT 6 . . . 1 10 LSB IN
MASTER MSB OUT2
BIT 6 . . . 1
MASTER LSB OUT
PORT DATA
Figure A-6 SPI Master Timing (CPHA =1) Table A-18 SPI Master Mode Timing Characteristics1
Conditions are shown in Table A-4 unless otherwise noted, CLOAD = 200pF on all outputs
Num C
1 1 2 3 4 5 6 9 10 11 12 P Operating Frequency
Rating
Symbol
fop tsck tlead tlag twsck tsu thi tv tho tr tf
Min
DC 4 1/2 1/2 tbus - 30 25 0
Typ
Max
1/4 2048 --
Unit
fbus tbus tsck tsck
P SCK Period tsck = 1./fop D Enable Lead Time D Enable Lag Time D Clock (SCK) High or Low Time D Data Setup Time (Inputs) D Data Hold Time (Inputs) D Data Valid (after SCK Edge) D Data Hold Time (Outputs) D Rise Time Inputs and Outputs D Fall Time Inputs and Outputs
1024 tbus
ns ns ns
25 0 25 25
ns ns ns ns
NOTES: 1. The numbers 7, 8 in the column labeled "Num" are missing. This has been done on purpose to be consistent between the Master and the Slave timing shown in Table A-19.
110
MC9S12DJ64 Device User Guide -- V01.10
A.7.2 Slave Mode
Figure A-7 and Figure A-8 illustrate the slave mode timing. Timing values are shown in Table A-19.
SS (INPUT) 1 SCK (CPOL = 0) (INPUT) 2 SCK (CPOL = 1) (INPUT) 7 MISO (OUTPUT) SLAVE 5 MOSI (INPUT) MSB IN MSB OUT 6 BIT 6 . . . 1 LSB IN 9 BIT 6 . . . 1 4 4 11 12 8 10 10 12 11 3
SLAVE LSB OUT
Figure A-7 SPI Slave Timing (CPHA = 0)
SS (INPUT) 1 2 SCK (CPOL = 0) (INPUT) 4 SCK (CPOL = 1) (INPUT) 9 MISO (OUTPUT) 7 MOSI (INPUT) SLAVE 5 MSB IN MSB OUT 6 BIT 6 . . . 1 LSB IN 4 11 12 12 11 3
10 BIT 6 . . . 1 SLAVE LSB OUT
8
Figure A-8 SPI Slave Timing (CPHA =1)
111
MC9S12DJ64 Device User Guide -- V01.10
Table A-19 SPI Slave Mode Timing Characteristics
Conditions are shown in Table A-4 unless otherwise noted, CLOAD = 200pF on all outputs
Num C
1 1 2 3 4 5 6 7 8 9 10 11 12 P Operating Frequency
Rating
Symbol
fop tsck tlead tlag twsck tsu thi ta tdis tv tho tr tf
Min
DC 4 1 1 tcyc - 30 25 25
Typ
Max
1/4 2048
Unit
fbus tbus tcyc tcyc ns ns ns
P SCK Period tsck = 1./fop D Enable Lead Time D Enable Lag Time D Clock (SCK) High or Low Time D Data Setup Time (Inputs) D Data Hold Time (Inputs) D Slave Access Time D Slave MISO Disable Time D Data Valid (after SCK Edge) D Data Hold Time (Outputs) D Rise Time Inputs and Outputs D Fall Time Inputs and Outputs
1 1 25 0 25 25
tcyc tcyc ns ns ns ns
112
MC9S12DJ64 Device User Guide -- V01.10
A.8 External Bus Timing
A timing diagram of the external multiplexed-bus is illustrated in Figure A-9 with the actual timing values shown on table Table A-20. All major bus signals are included in the diagram. While both a data write and data read cycle are shown, only one or the other would occur on a particular bus cycle.
A.8.1 General Muxed Bus Timing
The expanded bus timings are highly dependent on the load conditions. The timing parameters shown assume a balanced load across all outputs.
113
MC9S12DJ64 Device User Guide -- V01.10
1, 2 3 ECLK PE4 5 9 Addr/Data (read) PA, PB data 6 15 addr 7 12 Addr/Data (write) PA, PB data addr 8 14 data 13 16 10 data 11 4
17 Non-Multiplexed Addresses PK5:0 20 ECS PK7
18
19
21
22
23
24 R/W PE2
25
26
27 LSTRB PE3
28
29
30 NOACC PE7
31
32
33 IPIPO0 IPIPO1, PE6,5
34
35
36
Figure A-9 General External Bus Timing
114
MC9S12DJ64 Device User Guide -- V01.10
Table A-20 Expanded Bus Timing Characteristics
Conditions are shown in Table A-4 unless otherwise noted, CLOAD = 50pF
Num C
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Rating
Symbol
fo tcyc PWEL PWEH tAD tAV tMAH tAHDS tDHA tDSR tDHR tDDW tDHW tDSW tACCA tACCE tNAD tNAV tNAH tCSD tACCS tCSH tCSN tRWD tRWV tRWH tLSD tLSV tLSH tNOD tNOV
Min
0 40 19 19
Typ
Max
25.0
Unit
MHz ns ns ns
P Frequency of operation (E-clock) P Cycle time D Pulse width, E low D Pulse width, E high1 D Address delay time D Address valid time to E rise (PWEL-tAD) D Muxed address hold time D Address hold to data valid D Data hold to address D Read data setup time D Read data hold time D Write data delay time D Write data hold time D Write data setup time1 (PWEH-tDDW) D Address access time1 (tcyc-tAD-tDSR) D E high access time1 (PWEH-tDSR) D Non-multiplexed address delay time D Non-muxed address valid to E rise (PWEL-tNAD) D Non-multiplexed address hold time D Chip select delay time D Chip select access time1 (tcyc-tCSD-tDSR) D Chip select hold time D Chip select negated time D Read/write delay time D Read/write valid time to E rise (PWEL-tRWD) D Read/write hold time D Low strobe delay time D Low strobe valid time to E rise (PWEL-tLSD) D Low strobe hold time D NOACC strobe delay time D NOACC valid time to E rise (PWEL-tNOD)
8 11 2 7 2 13 0 7 2 12 19 6 6 15 2 16 11 2 8 7 14 2 7 14 2 7 14
ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
115
MC9S12DJ64 Device User Guide -- V01.10
Table A-20 Expanded Bus Timing Characteristics
Conditions are shown in Table A-4 unless otherwise noted, CLOAD = 50pF
Num C
32 33 34 35 36 D NOACC hold time D IPIPO[1:0] delay time
Rating
Symbol
tNOH tP0D tP0V tP1D tP1V
Min
2 2 11 2 11
Typ
Max
Unit
ns
7
ns ns
D IPIPO[1:0] valid time to E rise (PWEL-tP0D) D IPIPO[1:0] delay time1 (PWEH-tP1V) D IPIPO[1:0] valid time to E fall
25
ns ns
NOTES: 1. Affected by clock stretch: add N x tcyc where N=0,1,2 or 3, depending on the number of clock stretches.
116
MC9S12DJ64 Device User Guide -- V01.10
Appendix B Package Information
B.1 General
This section provides the physical dimensions of the MC9S12DJ64 packages.
117
MC9S12DJ64 Device User Guide -- V01.10
B.2 112-pin LQFP package
4X PIN 1 IDENT 1 112
0.20 T L-M N
4X 28 TIPS 85 84
0.20 T L-M N
J1 J1 C L
4X
P
VIEW Y
108X
G
X X=L, M OR N
VIEW Y B L M B1 V1 V
J
AA
28
57
F D 0.13
M
BASE METAL
29
56
T L-M N
N A1 S1 A S
SECTION J1-J1 ROTATED 90 COUNTERCLOCKWISE
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. DATUMS L, M AND N TO BE DETERMINED AT SEATING PLANE, DATUM T. 4. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE, DATUM T. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER SIDE. DIMENSIONS A AND B INCLUDE MOLD MISMATCH. 6. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.46. MILLIMETERS MIN MAX 20.000 BSC 10.000 BSC 20.000 BSC 10.000 BSC --1.600 0.050 0.150 1.350 1.450 0.270 0.370 0.450 0.750 0.270 0.330 0.650 BSC 0.090 0.170 0.500 REF 0.325 BSC 0.100 0.200 0.100 0.200 22.000 BSC 11.000 BSC 22.000 BSC 11.000 BSC 0.250 REF 1.000 REF 0.090 0.160 8 0 7 3 13 11 11 13
C2 C 0.050 2
VIEW AB 0.10 T
112X
SEATING PLANE
3 T
R
R2 0.25
GAGE PLANE
R
R1
C1 (Y) (Z) VIEW AB
(K) E
1
DIM A A1 B B1 C C1 C2 D E F G J K P R1 R2 S S1 V V1 Y Z AA 1 2 3
Figure B-1 112-pin LQFP mechanical dimensions (case no. 987)
118
MC9S12DJ64 Device User Guide -- V01.10
B.3 80-pin QFP package
L
60 61 41 40
S
S
B B P
D
L
H A-B
B
V 0.05 D
M
M
C A-B
-A-
-B-
S
S
D
0.20
0.20
-A-,-B-,-DDETAIL A
DETAIL A
80 1 20
21
-D0.20
M
F
A H A-B S
S
D
S
0.05 A-B J
S
N
0.20 E C -CSEATING PLANE
M
C A-B
D
S
M DETAIL C -HH G
DATUM PLANE
D 0.20
M
C A-B
S
D
S
SECTION B-B
VIEW ROTATED 90
0.10 M
U T
DATUM PLANE
-H-
R
K W X DETAIL C
Q
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE -H- IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS -A-, -B- AND -D- TO BE DETERMINED AT DATUM PLANE -H-. 5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE -C-. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE -H-. 7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT.
DIM A B C D E F G H J K L M N P Q R S T U V W X
MILLIMETERS MIN MAX 13.90 14.10 13.90 14.10 2.15 2.45 0.22 0.38 2.00 2.40 0.22 0.33 0.65 BSC --0.25 0.13 0.23 0.65 0.95 12.35 REF 5 10 0.13 0.17 0.325 BSC 0 7 0.13 0.30 16.95 17.45 0.13 --0 --16.95 17.45 0.35 0.45 1.6 REF
Figure B-2 80-pin QFP Mechanical Dimensions (case no. 841B)
119
MC9S12DJ64 Device User Guide -- V01.10
120
MC9S12DJ64 Device User Guide -- V01.10
User Guide End Sheet
121
MC9S12DJ64 Device User Guide -- V01.10
FINAL PAGE OF 122 PAGES
122

▲Up To Search▲

Price & Availability of MC9S12D64

	To Download MC9S12D64 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .