View ADM1085NBSP_295906.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Simple SequencersTM in 6-Lead SC70 ADM1085/ADM1086/ADM1087/ADM1088
FEATURES
Provide programmable time delays between enable signals Can be cascaded with power modules for multiple supply sequencing Power supply monitoring from 0.6 V Output stages: High voltage (up to 22 V) open-drain output (ADM1085/ADM1087) Push-pull output (ADM1086/ADM1088) Capacitor-adjustable time delays High voltage (up to 22 V) Enable and VIN inputs Low power consumption (15 A) Specified over -40C to +125C temperature range 6-lead SC70 package
FUNCTIONAL BLOCK DIAGRAMS
VCC
ADM1085/ADM1086
VIN 0.6V CAPACITOR ADJUSTABLE DELAY
ENOUT
GND
CEXT
ENIN
VCC
ADM1087/ADM1088
VIN 0.6V CAPACITOR ADJUSTABLE DELAY
ENOUT
Desktop/notebook computers, servers Low power portable equipment Routers Base stations Line cards Graphics cards
GND
CEXT
ENIN
Figure 1.
GENERAL DESCRIPTION
The ADM1085/ADM1086/ADM1087/ADM1088 are simple sequencing circuits that provide a time delay between the enabling of voltage regulators and/or dc-dc converters at powerup in multiple supply systems. When the output voltage of the first power module reaches a preset threshold, a time delay is initiated before an enable signal allows subsequent regulators to power up. Any number of these devices can be cascaded with regulators to allow sequencing of multiple power supplies. Threshold levels can be set with a pair of external resistors in a voltage divider configuration. By choosing appropriate resistor values, the threshold can be adjusted to monitor voltages as low as 0.6 V. The ADM1086 and ADM1088 have push-pull output stages, with active-high (ENOUT) and active-low (ENOUT) logic outputs, respectively. The ADM1085 has an active-high (ENOUT) logic output; the ADM1087 has an active-low (ENOUT) output. Both the ADM1085 and ADM1087 have open-drain output stages that can be pulled up to voltage levels as high as 22 V through an external resistor. This level-shifting
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
property ensures compatibility with enable input logic levels of different regulators and converters. All four models have a dedicated enable input pin that allows the output signal to the regulator to be controlled externally. This is an active-high input (ENIN) for the ADM1085 and ADM1086, and an active-low input (ENIN) for the ADM1087 and ADM1088. The simple sequencers are specified over the extended -40C to +125C temperature range. With low current consumption of 15 A (typ) and 6-lead SC70 packaging, the parts are suitable for low-power portable applications. Table 1. Selection Table
Output Stage Part No. ADM1085 ADM1086 ADM1087 ADM1088 Enable Input ENIN ENIN ENIN ENIN ENOUT ENOUT Open-Drain Push-Pull
Open-Drain Push-Pull
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved.
04591-PrG-001
APPLICATIONS
ADM1085/ADM1086/ADM1087/ADM1088 TABLE OF CONTENTS
Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 4 ESD Caution.................................................................................. 4 Pin Configuration and Function Descriptions............................. 5 Typical Performance Characteristics ............................................. 6 Circuit Information .......................................................................... 9 Timing Characteristics and Truth Tables.................................. 9 Capacitor-Adjustable Delay Circuit........................................... 9 Open-Drain and Push-Pull Outputs ....................................... 10 Application Information................................................................ 11 Sequencing Circuits ................................................................... 11 Dual LOFO Sequencing ............................................................ 13 Simultaneous Enabling.............................................................. 13 Power Good Signal Delays........................................................ 13 Quad-Supply Power Good Indicator....................................... 14 Sequencing with FET Switches................................................. 14 Outline Dimensions ....................................................................... 15 Ordering Guide .......................................................................... 15
REVISION HISTORY
7/04--Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADM1085/ADM1086/ADM1087/ADM1088 SPECIFICATIONS
VCC = full operating range, TA = -40C to +125C, unless otherwise noted. Table 2.
Parameter SUPPLY VCC Operating Voltage Range VIN Operating Voltage Range Supply Current VIN Rising Threshold, VTH_RISING VIN Falling Threshold, VTH_FALLING VIN Hysteresis VIN to ENOUT/ENOUT Delay VIN Rising VIN Falling VIN Leakage Current CEXT Charge Current Threshold Temperature Coefficient ENIN/ENIN TO ENOUT/ENOUT Propagation Delay ENIN/ENIN Voltage Low ENIN/ENIN Voltage High ENIN/ENIN Leakage Current ENOUT/ENOUT Voltage Low Min 2.25 0 0.56 0.545 10 0.6 0.585 15 35 2 20 170 250 30 0.5 Typ Max 3.6 22 15 0.64 0.625 Unit V V A V V mV s ms s A nA ppm/C s V V A V Test Conditions/Comments
VCC = 3.3 V VCC = 3.3 V
CEXT floating, C = 20 pF CEXT = 470 pF VIN = VTH_FALLING to (VTH_FALLING - 100 mV) VIN = 22 V
125
375
VIN > VTH_RISING
0.3 VCC - 0.2 0.3 VCC + 0.2 170 0.4
ENOUT/ENOUT Voltage High (ADM1086/ADM1088) ENOUT/ENOUT Open-Drain Output Leakage Current (ADM1085/ADM1087)
0.8 VCC
V
0.4
A
ENIN/ENIN = 22 V VIN < VTH_FALLING (ENOUT), VIN > VTH_RISING (ENOUT), ISINK = 1.2 mA VIN > VTH_RISING (ENOUT), VIN < VTH_FALLING (ENOUT), ISOURCE = 500 A ENOUT/ENOUT = 22 V
Rev. 0 | Page 3 of 16
ADM1085/ADM1086/ADM1087/ADM1088 ABSOLUTE MAXIMUM RATINGS
TA = 25C, unless otherwise noted. Table 3.
Parameter VCC VIN CEXT ENIN, ENIN ENOUT, ENOUT (ADM1085, ADM1087) ENOUT, ENOUT (ADM1086, ADM1088) Operating Temperature Range Storage Temperature Range JA Thermal Impedance, SC70 Lead Temperature Soldering (10 s) Vapor Phase (60 s) Infrared (15 s) Rating -0.3 V to +6 V -0.3 V to +25 V -0.3 V to +6 V -0.3 V to +25 V -0.3 V to +25 V -0.3 V to +6 V -40C to +125C -65C to +150C 146C/W 300C 215C 220C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
Rev. 0 | Page 4 of 16
ADM1085/ADM1086/ADM1087/ADM1088 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
ENIN/ENIN 1 GND 2 VIN 3
04591-PrG-002
ADM1085/ ADM1086/ ADM1087/ ADM1088
6 5
VCC CEXT
4 ENOUT/ENOUT TOP VIEW (Not to Scale)
Figure 2. Pin Configuration
Table 4. Pin Function Descriptions
Pin No. 1 2 3 Mnemonic ENIN, ENIN GND VIN Description Enable Input. Controls the status of the enable output. Active high for ADM1085/ADM1086. Active low for ADM1087/ADM1088. Ground. Input for the Monitored Voltage Signal. Can be biased via a voltage divider resistor network to customize the effective input threshold. Can precisely monitor an analog power supply output signal and detect when it has powered up. The voltage applied at this pin is compared with a 0.6 V on-chip reference. With this reference, digital signals with various logic-level thresholds can also be detected. Enable Output. Asserted when the voltage at VIN is above VTH_RISING and the time delay has elapsed, provided that the enable input is asserted. Active high for the ADM1085/ADM1086. Active low for the ADM1087/ADM1088. External Capacitor Pin. The capacitance on this pin determines the time delay on the enable output. The delay is seen only when the voltage at VIN rises past VTH_RISING, and not when it falls below VTH_FALLING. Power Supply.
4
ENOUT, ENOUT
5 6
CEXT VCC
Rev. 0 | Page 5 of 16
ADM1085/ADM1086/ADM1087/ADM1088 TYPICAL PERFORMANCE CHARACTERISTICS
700 680
VIN LEAKAGE CURRENT (A)
200 180 TA = +125C 160 140 TA = +25C 120 100 80 60 40 20 0 0 2 4 6 8 10 12 VIN (V) 14 16 18 20 22 TA = -40C
660 640 VTRIP RISING
VTRIP (mV)
620 600 580 560
04591-PrG-003
520 500 -40 -25 -10 5 20 35 50 65 TEMPERATURE (C) 80 95 110
125
Figure 3. VIN Threshold vs. Temperature
Figure 6. VIN Leakage Current vs. VIN Voltage
12.0 11.5 TA = +25C
VIN LEAKAGE CURRENT (A)
200 190 180 170 160 150 140 130
04591-PrG-007
TA = +125C
11.0 10.5
ICC (A)
TA = +25C
10.0 TA = -40C 9.5 9.0 8.5 8.0 2.10
04591-PrG-004
TA = +125C
TA = -40C
120 110 100 2.10 2.40 2.70 VCC (V) 3.00 3.30
2.40
2.70 VCC (V)
3.00
3.30
3.60
3.60
Figure 4. Supply Current vs. Supply Voltage
Figure 7. VIN Leakage Current vs. VCC Voltage
20 18 16
10000 TA = +125C 1000
SUPPLY CURRENT (A)
OUTPUT VOLTAGE (mV)
14 12 10 8 6
04591-PrG-005
TA = +25C 100 TA = -40C 10
4 2 0 0 2 4 6 8 10 12 VIN (V) 14 16 18 20 22
0.1 0.01
0.1 1 10 OUTPUT SINK CURRENT (mA)
20
100
Figure 5. Supply Current vs. VIN Voltage
Figure 8. Output Voltage vs. Output Sink Current
Rev. 0 | Page 6 of 16
04591-PrG-008
1
04591-PrG-006
540
VTRIP FALLING
ADM1085/ADM1086/ADM1087/ADM1088
200
120
180 TA = +125C
OUTPUT LOW VOLTAGE (mV)
100
ENIN/ENIN LEAKAGE (A)
160 TA = +25C 140 120 100 TA = -40C 80 60
04591-PrG-012
80
60
40
04591-PrG-009
20
40 20 0 0 2 4 6 8 10 12 14 ENIN/ENIN (V) 16 18 20 22
0 2.10
2.40
2.70 3.00 SUPPLY VOLTAGE (V)
3.30
3.60
Figure 9. Output Low Voltage vs. Supply Voltage
Figure 12. ENIN/ENIN Leakage Current vs. ENIN/ENIN Voltage
100 90 80
PROPAGATION DELAY (s) ENIN LEAKAGE (A)
200 TA = +125C 180 160 140 120 100 80 60
04591-PrG-013
70 60 1mV/s 50 40 10mV/s 30
04591-PrG-010
TA = +25C TA = -40C
20 10 0 -40 -25 -10 5 20 35 50 65 TEMPERATURE (C) 80 95 110
40 20 0 2.10 2.40 2.70 VCC (V) 3.00 3.30
125
3.60
Figure 10. VCC Falling Propagation Delay vs. Temperature
Figure 13. ENIN/ENIN Leakage Current vs. VCC Voltage
500 450 400 350
FALL TIME (ns)
10000
1000
250 200 150
04591-PrG-011
CEXT (nF)
300
100
10
50 0 2.10 2.40 2.70 3.00 SUPPLY VOLTAGE (V) 3.30
3.60
0.1 0.562 2.390
5.02
22.9 53.2 241 520 TIMEOUT DELAY (ms)
2350
4480 26200
Figure 11. Output Fall Time vs. Supply Voltage
Figure 14. CEXT Capacitance vs. Timeout Delay
Rev. 0 | Page 7 of 16
04591-PrG-014
100
1
ADM1085/ADM1086/ADM1087/ADM1088
300 280 260
TRANSIENT DURATION (s)
04591-PrG-015
100 90 80 70 60 50 40 30
04591-PrG-017
CHARGE CURRENT (nA)
240 220 200 180 160 140 120 100 -40 -25 -10 5 20 35 50 65 TEMPERATURE (C) 80 95 110
20 10 0 1 10 100 COMPARATOR OVERDRIVE (mV)
125
1000
Figure 15. CEXT Charge Current vs. Temperature
Figure 17. Maximum VIN Transient Duration vs. Comparator Overdrive
100 90 80
PROPAGATION DELAY (s)
70 60 50 40 30
04591-PrG-016
20 10 0 -40 -25 -10 5 20 35 50 65 TEMPERATURE (C) 80 95 110
125
Figure 16. VIN to ENOUT/ENOUT Propagation Delay (CEXT Floating) vs. Temperature
Rev. 0 | Page 8 of 16
ADM1085/ADM1086/ADM1087/ADM1088 CIRCUIT INFORMATION
TIMING CHARACTERISTICS AND TRUTH TABLES
The enable outputs of the ADM1085/ADM1086/ADM1087/ ADM1088 are related to the VIN and enable inputs by a simple AND function. The enable output is asserted only if the enable input is asserted and the voltage at VIN is above VTH_RISING, with the time delay elapsed. Table 5 and Table 6 show the enable output logic states for different VIN/enable input combinations when the capacitor delay has elapsed. The timing diagrams in Figure 18 and Figure 19 give a graphical representation of how the ADM1085/ADM1086/ADM1087/ADM1088 enable outputs respond to VIN and enable input signals. Table 5. ADM1085/ADM1086 Truth Table
VIN VTH_RISING >VTH_RISING ENIN 0 1 0 1 ENOUT 0 0 0 1
When VIN reaches the upper threshold voltage (VTH_RISING), an internal circuit generates a delay (tEN) before the enable output is asserted. If VIN drops below the lower threshold voltage (VTH_FALLING), the enable output is deasserted immediately. Similarly, if the enable input is disabled while VIN is above the threshold, the enable output deasserts immediately. Unlike VIN, a low-to-high transition on ENIN (or high-to-low on ENIN) does not yield a time delay on ENOUT (ENOUT).
CAPACITOR-ADJUSTABLE DELAY CIRCUIT
Figure 20 shows the internal circuitry used to generate the time delay on the enable output. A 250 nA current source charges a small internal parasitic capacitance, CINT. When the capacitor voltage reaches 1.2 V, the enable output is asserted. The time taken for the capacitor to reach 1.2 V, in addition to the propagation delay of the comparator, constitutes the enable timeout, which is typically 35 s. To minimize the delay between VIN falling below VTH_FALLING and the enable output de-asserting, an NMOS transistor is connected in parallel with CINT. The output of the voltage detector is connected to the gate of this transistor so that, when VIN falls below VTH_FALLING, the transistor switches on and CINT discharges quickly.
VCC SIGNAL FROM VOLTAGE DETECTOR 250nA TO AND GATE AND OUTPUT STAGE
04591-PrG-024
Table 6. ADM1087/ADM1088 Truth Table
VIN VTH_RISING >VTH_RISING ENIN 1 0 1 0 ENOUT 1 1 1 0
VIN
VTH_RISING
VTH_FALLING
CINT
1.2V
CEXT
ENIN
04591-PrG-023
C
Figure 20. Capacitor-Adjustable Delay Circuit
ENOUT
tEN
Figure 18. ADM1085/ADM1086 Timing Diagram
Connecting an external capacitor to the CEXT pin delays the rise time--and therefore the enable timeout--further. The relationship between the value of the external capacitor and the resulting timeout is characterized by the following equation: tEN = (C x 4.8 x106) + 35 s
VIN
VTH_RISING
VTH_FALLING
ENIN
04591-PrG-024
ENOUT
tEN
Figure 19. ADM1087/ADM1088 Timing Diagram
Rev. 0 | Page 9 of 16
ADM1085/ADM1086/ADM1087/ADM1088
OPEN-DRAIN AND PUSH-PULL OUTPUTS
The ADM1085 and ADM1087 have open-drain output stages that require an external pull-up resistor to provide a logic-high voltage level. The geometry of the NMOS transistor enables the output to be pulled up to voltage levels as high as 22 V.
VCC (22V)
The ADM1086 and ADM1088 have push-pull (CMOS) output stages that require no external components to drive other logic circuits. An internal PMOS pull-up transistor provides the logic-high voltage level.
ADM1086/ADM1088
VCC
LOGIC
04591-PrG-026
04591-PrG-027
ADM1085/ADM1087
LOGIC
Figure 21. Open-Drain Output Stage
Figure 22. Push-Pull Output Stage
Rev. 0 | Page 10 of 16
ADM1085/ADM1086/ADM1087/ADM1088 APPLICATION INFORMATION
SEQUENCING CIRCUITS
The ADM1085/ADM1086/ADM1087/ADM1088 are compatible with voltage regulators and dc-to-dc converters that have active-high or active-low enable or shutdown inputs, with a choice of open-drain or push-pull output stages. Figure 23 to Figure 25 illustrate how each of the ADM1085/ADM1086/ ADM1087/ADM1088 simple sequencers can be used in multiple-supply systems, depending on which regulators are used and which output stage is preferred. In Figure 23, three ADM1085s are used to sequence four supplies on power-up. Separate capacitors on the CEXT pins determine the time delays between enabling of the 3.3 V, 2.5 V, 1.8 V, and 1.2 V supplies. Because the dc/dc converters and ADM1085s are connected in cascade, and the output of any converter is dependent on that of the previous one, an external controller can disable all four supplies simultaneously by disabling the first dc/dc converter in the chain. For power-down sequencing, an external controller dictates when the supplies are switched off by accessing the ENIN inputs individually.
3.3V EN 3.3V IN OUT EN 3.3V IN OUT 3.3V EN 3.3V IN OUT
12V 3.3V EN IN OUT
DC/DC
3.3V
DC/DC
2.5V
DC/DC
1.8V
DC/DC
1.2V
ENABLE CONTROL
VCC VIN ENOUT VIN
VCC ENOUT VIN
VCC ENOUT
ADM1085
ENIN CEXT
ADM1085
ENIN CEXT
ADM1085
ENIN CEXT
12V
3.3V 2.5V 1.8V 1.2V
04591-PrG-028
tEN1
tEN2
tEN3
EXTERNAL DISABLE
Figure 23. Typical ADM1085 Application Circuit
Rev. 0 | Page 11 of 16
ADM1085/ADM1086/ADM1087/ADM1088
12V IN IN IN IN
EN
DC/DC
OUT
3.3V 3.3V
EN
DC/DC
OUT
2.5V 3.3V
EN
DC/DC
OUT
1.8V 3.3V
EN
DC/DC
OUT
1.2V
VCC VIN ENOUT VIN
VCC ENOUT VIN
VCC ENOUT
ADM1086
ENIN CEXT
ADM1086
ENIN CEXT
ADM1086
ENIN CEXT
ENABLE CONTROL 12V
3.3V 2.5V 1.8V 1.2V
04591-PrG-029
tEN1
tEN2
tEN3
EXTERNAL DISABLE
Figure 24. Typical ADM1086 Application Circuit
12V
12V
SD
IN
ADP3334
OUT
3.3V 3.3V
SD
IN
ADP3334
OUT
2.5V
SD
IN
ADP3334
OUT
3.3V 3.3V
SD
IN
ADP3334
OUT
2.5V
VCC VIN ENOUT
04591-PrG-030
VCC VIN ENOUT
04591-PrG-031
ADM1087
ENIN CEXT
ADM1088
ENIN CEXT
Figure 25. Typical ADM1087 Application Circuit Using ADP3334 Voltage Regulators
Figure 26. Typical ADM1088 Application Circuit Using ADP3334 Voltage Regulators
Rev. 0 | Page 12 of 16
ADM1085/ADM1086/ADM1087/ADM1088
DUAL LOFO SEQUENCING
A power sequencing solution for a portable device, such as a PDA, is shown in Figure 27. This solution requires that the microprocessor's power supply turn on before the LCD display turns on, and that the LCD display power-down before the microprocessor powers down. In other words, the last power supply to turn on is the first one to turn off (LOFO). An RC network connects the battery and the SD input of the ADP3333 voltage regulator. This causes power-up and powerdown transients to appear at the SD input when the battery is connected and disconnected. The 3.3 V microprocessor supply turns on quickly on power-up and turns off slowly on powerdown. This is due to two factors: Capacitor C1 charges up to 9 V on power-up and charges down from 9 V on power-down, and the SD pin has logic-high and logic-low input levels of 2 V and 0.4 V. For the display power sequencing, the ADM1085 is equipped with capacitor C2, which creates the delay between the microprocessor and display power turning on. When the system is powered down, the ADM1085 turns off the display power immediately, while the 3.3 V regulator waits for C1 to discharge to 0.4 V before switching off.
9V SYSTEM POWER SWITCH SD ADP3333 2.5V 9V C1 MICROPROCESSOR POWER 9V
SIMULTANEOUS ENABLING
The enable output can drive multiple enable or shutdown regulator inputs simultaneously.
12V 3.3V SD IN IN
ADP3333
OUT
3.3V 3.3V
SD
ADP3333
OUT 2.5V
VCC VIN ENOUT 12V CEXT IN
ADM1085
ENIN SD 1.8V ENABLE CONTROL
04591-PrG-033
ADP3333
OUT
Figure 28. Enabling a Pair of Regulators from a Single ADM1085
POWER GOOD SIGNAL DELAYS
Sometimes sequencing is performed by asserting Power Good signals when the voltage regulators are already on, rather than sequencing the power supplies directly. In these scenarios, a simple sequencer IC can provide variable delays so that enabling separate circuit blocks can be staggered in time. For example, in a notebook PC application, a dedicated microcomputer asserts a Power Good signal for North BridgeTM and South BridgeTM ICs. The ADM1086 delays the south bridge's signal, so that it is enabled after the north bridge.
5V 5V POWER_GOOD EN
3.3V VIN
MICROCOMPUTER
ENOUT SD ADP3333 5V DISPLAY POWER
ADM1086
ENIN CEXT C2
NORTH BRIDGE IC
3.3V VIN ENOUT EN
5V
0V 9V VC1 0V 2.5V MICROPROCESSOR POWER 0V 5V DISPLAY POWER 0V
04591-PrG-032
ENIN
CEXT
Figure 29. Power Good Delay
Figure 27. Dual LOFO Power-Supply Sequencing
Rev. 0 | Page 13 of 16
04591-PrG-034
SYSTEM POWER
9V
ADM1086
SOUTH BRIDGE IC
ADM1085/ADM1086/ADM1087/ADM1088
QUAD-SUPPLY POWER GOOD INDICATOR
The enable output of the simple sequencers is equivalent to an AND function of VIN and ENIN. ENOUT is high only when the voltage at VIN is above the threshold and the enable input (ENIN) is high as well. Although ENIN is a digital input, it can tolerate voltages as high as 22 V and can detect if a supply is present. Therefore, a simple sequencer can monitor two supplies and assert what can be interpreted as a Power Good signal when both supplies are present. The outputs of two ADM1085s can be wire-ANDed together to make a quad-supply Power Good indicator.
3.3V 3.3V 9V VIN POWER_GOOD
2.5V
SEQUENCING WITH FET SWITCHES
The open-drain outputs of the ADM1085 and ADM1087 can drive external FET transistors, which can switch on powersupply rails. All that is needed is a pull-up resistor to a voltage source that is high enough to turn on the FET.
12V
3.3V
VIN
ENOUT
ADM1085
ENIN CEXT
04591-PrG-036
ENOUT
ADM1085
5V ENIN
Figure 31. Sequencing with a FET Switch
3.3V 2.5V VIN
ENOUT
04591-PrG-035
ADM1085
1.8V ENIN
Figure 30. Quad-Supply Power Good Indicator
Rev. 0 | Page 14 of 16
ADM1085/ADM1086/ADM1087/ADM1088 OUTLINE DIMENSIONS
2.00 BSC
6 5 2 4
1.25 BSC
1 3
2.10 BSC
PIN 1 0.65 BSC 1.30 BSC 1.00 0.90 0.70 1.10 MAX 0.22 0.08 0.30 0.15 0.10 COPLANARITY COMPLIANT TO JEDEC STANDARDS MO-203AB SEATING PLANE 8 4 0
0.10 MAX
0.46 0.36 0.26
Figure 32. 6-Lead Plastic Surface-Mount Package [SC70] (KS-6) Dimensions shown in millimeters
ORDERING GUIDE
Model ADM1085AKS-REEL7 ADM1086AKS-REEL7 ADM1087AKS-REEL7 ADM1088AKS-REEL7 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C Quantity 3k 3k 3k 3k Package Description 6-Lead Thin Shrink Small Outline Transistor Package (SC70) 6-Lead Thin Shrink Small Outline Transistor Package (SC70) 6-Lead Thin Shrink Small Outline Transistor Package (SC70) 6-Lead Thin Shrink Small Outline Transistor Package (SC70) Package Option KS-6 KS-6 KS-6 KS-6 Branding M0V M0W M0X M0Y
Rev. 0 | Page 15 of 16
ADM1085/ADM1086/ADM1087/ADM1088 NOTES
(c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04591-0-7/04(0)
Rev. 0 | Page 16 of 16

▲Up To Search▲

Price & Availability of ADM1085NBSP

	To Download ADM1085NBSP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .