![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
v01.0604 MICROWAVE CORPORATION HMC373LP3 Features Noise Figure: 0.9 dB +35 dBm Output IP3 Gain: 14 dB Low Loss LNA Bypass Path Single Supply: +5.0 V @ 90 mA 50 Ohm Matched Output GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz 8 AMPLIFIERS - SMT Typical Applications The HMC373LP3 is ideal for basestation receivers: * GSM, GPRS & EDGE * CDMA & W-CDMA * Private Land Mobile Radio Functional Diagram General Description The HMC373LP3 is a versatile, high dynamic range GaAs MMIC Low Noise Amplifier that integrates a low loss LNA bypass mode on the IC. The amplifier is ideal for GSM & CDMA cellular basestation frontend receivers operating between 700 and 1000 MHz and provides 0.9 dB noise figure, 14 dB of gain and +35 dBm IP3 from a single supply of +5.0V @ 90 mA. Input and output return losses are 28 and 12 dB respectively with the LNA requiring minimal external components to optimize the RF input match, RF ground and DC bias. By presenting an open or short circuit to a single control line, the LNA can be switched into a low 2.0 dB loss bypass mode reducing the current consumption to 10 A. A low cost, leadless 3x3 mm QFN surface mount package (LP3) houses the low noise amplifier. Electrical Specifications, TA = +25 C, Vdd = +5V LNA Mode Parameter Min. Frequency Range Gain Gain Variation Over Temperature Noise Figure Input Return Loss Output Return Loss Reverse Isolation Power for 1dB Compression (P1dB)* Saturated Output Power (Psat) Third Order Intercept (IP3)* (-20 dBm Input Power per tone, 1 MHz tone spacing) Supply Current (Idd) 18 11.5 Typ. 810 - 960 13.5 0.008 0.9 28 12 20 21 22.5 35.5 90 17 0.015 1.3 10.5 Max. Min. Typ. 700 - 1000 14 0.008 1.0 25 11 19 20 22 35 90 50 0.01 30 0.015 1.4 30 25 -2.8 Max. Min. Typ. 700 - 1000 -2.0 0.002 0.004 Max. MHz dB dB / C dB dB dB dB dBm dBm dBm mA LNA Mode Bypass Mode Units * P1dB and IP3 for LNA Mode are referenced to RFOUT while P1dB and IP3 for Bypass Mode are referenced to RFIN. 8 - 132 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz LNA Broadband Gain & Return Loss 20 15 10 5 RESPONSE (dB) 0 -5 -10 -15 -20 -25 -30 -35 -40 0.25 0.5 0.75 1 1.25 1.5 S21 S11 S22 LNA - Gain, Noise Figure & Power vs. Supply Voltage @ 850 MHz 22 21 GAIN (dB), P1dB (dBm) 20 19 18 17 16 15 14 13 12 2 Gain P1dB Noise Figure 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 4.75 5 Vdd (Vdc) 5.25 5.5 8 AMPLIFIERS - SMT 8 - 133 NOISE FIGURE (dB) 1.75 4.5 FREQUENCY (GHz) LNA Gain vs. Temperature 20 19 18 LNA Noise Figure vs. Temperature 1.5 1.4 1.3 NOISE FIGURE (dB) 1.2 1.1 1 0.9 0.8 0.7 0.6 +25 C +85 C -40 C 17 GAIN (dB) 16 15 14 13 12 11 10 0.7 0.75 +25 C +85 C -40 C 0.8 0.85 0.9 0.95 1 0.5 0.7 0.75 0.8 0.85 0.9 0.95 1 FREQUENCY (GHz) FREQUENCY (GHz) LNA Gain vs. Vdd 20 19 18 LNA Noise Figure vs. Vdd 1.5 1.4 1.3 NOISE FIGURE (dB) 1.2 1.1 1 0.9 0.8 0.7 0.6 0.85 0.9 0.95 1 0.5 0.7 0.75 +4.5 V +5.0 V +5.5 V 17 GAIN (dB) 16 15 14 13 12 11 10 0.7 0.75 +4.5 V +5.0 V +5.5 V 0.8 0.8 0.85 0.9 0.95 1 FREQUENCY (GHz) FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz 8 AMPLIFIERS - SMT LNA Input Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 -40 0.7 +25 C +85 C -40 C LNA Output Return Loss vs. Temperature 0 -2 -4 RETURN LOSS (dB) -6 -8 -10 -12 -14 -16 -18 +25 C +85 C -40 C 0.75 0.8 0.85 0.9 0.95 1 -20 0.7 0.75 0.8 0.85 0.9 0.95 1 FREQUENCY (GHz) FREQUENCY (GHz) LNA Output IP3 vs. Temperature 40 39 38 OUTPUT IP3 (dBm) 37 36 35 34 33 32 31 30 0.7 0.75 0.8 0.85 0.9 +25 C +85 C -40 C LNA P1dB & Psat vs. Temperature 25 COMPRESSION POINT (dBm) 24 Psat 23 22 21 20 19 18 17 16 P1dB +25 C +85 C -40 C 0.95 1 15 0.7 0.75 0.8 0.85 0.9 0.95 1 FREQUENCY (GHz) FREQUENCY (GHz) LNA Output IP3 vs. Vdd 40 39 38 OUTPUT IP3 (dBm) 37 36 35 34 33 32 31 30 0.7 0.75 0.8 0.85 0.9 0.95 1 +4.5 V +5.0 V +5.5 V LNA P1dB vs. Vdd 25 24 23 22 P1dB (dBm) 21 20 19 18 17 16 15 0.7 0.75 0.8 0.85 0.9 +4.5 V +5.0 V +5.5 V 0.95 1 FREQUENCY (GHz) FREQUENCY (GHz) 8 - 134 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz LNA Reverse Isolation vs. Temperature 0 -5 ISOLATION (dB) -10 -15 -20 -25 -30 0.7 +25 C Bypass Mode Broadband Insertion Loss & Return Loss 0 -5 -10 RESPONSE (dB) -15 -20 -25 -30 -35 -40 0.25 S21 S11 S22 8 AMPLIFIERS - SMT 8 - 135 +85 C -40 C 0.75 0.8 0.85 0.9 0.95 1 0.5 0.75 1 1.25 1.5 1.75 2 FREQUENCY (GHz) FREQUENCY (GHz) Bypass Mode Insertion Loss vs. Temperature 0 -0.5 INSERTION LOSS (dB) -1 -1.5 -2 -2.5 -3 -3.5 -4 -4.5 -5 0.7 0.75 0.8 0.85 0.9 +25 C +85 C -40 C Bypass Mode Input Return Loss vs. Temperature 0 -5 -10 RETURN LOSS (dB) -15 -20 -25 -30 -35 -40 -45 1 -50 0.7 0.75 0.8 0.85 0.9 0.95 1 +25 C +85 C -40 C 0.95 FREQUENCY (GHz) FREQUENCY (GHz) Bypass Mode Output Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 -40 0.7 +25 C +85 C -40 C Bypass Mode Input IP3 vs. Temperature 55 50 INPUT IP3 (dBm) 45 40 +25 C +85 C -40 C 0.75 0.8 0.85 0.9 0.95 1 35 0.7 0.75 0.8 0.85 0.9 0.95 1 FREQUENCY (GHz) FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz 8 AMPLIFIERS - SMT Absolute Maximum Ratings Drain Bias Voltage (Vdd) RF Input Power (RFin)(Vdd = +5.0 Vdc) Channel Temperature Continuous Pdiss (T = 85 C) (derate 13.5 mW/C above 85 C) Thermal Resistance (channel to ground paddle) Storage Temperature Operating Temperature +8.0 Vdc LNA Mode +15 dBm Bypass Mode +30 dBm 150 C Typical Supply Current vs. Vdd Vdd (Vdc) +4.5 +5.0 +5.5 Idd (mA) 87 90 93 0.878 W Truth Table 74.1 C/W -65 to +150 C -40 to +85 C LNA Mode Bypass Mode Vctl= Short Circuit to DC Ground Vctl= Open Circuit Outline Drawing NOTES: 1. MATERIAL PACKAGE BODY: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY 3. LEAD AND GROUND PADDLE PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 6. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 7. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. 8 - 136 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz Pin Descriptions Pin Number 1, 3, 5, 8, 10, 12, 13, 15, 16 2 Function N/C Description No connection necessary. These pins may be connected to RF/DC ground. This pin is matched to 50 Ohms with a 19 nH inductor to ground. See Application Circuit. Interface Schematic 8 AMPLIFIERS - SMT 8 - 137 RF IN 4 Vctl DC ground return. LNA is in high gain mode when a short circuit is introduced to this pin through an external switch. LNA is in bypass mode when open circuit is introduced 6 ACG An external capacitor of 0.01F to ground is required for low frequency bypassing. See Application Circuit for further details. 7, 14 GND These pins must be connected to RF/DC ground. 9 Vdd Power supply voltage. Choke inductor and bypass capacitor are required. See application circuit. 11 RF OUT This pin is AC coupled and matched to 50 Ohms. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz 8 AMPLIFIERS - SMT Evaluation Board Circuit Note 1: Choose value of capacitor C1 for low frequency bypassing. A 0.01 F 10% capacitor is recommended. Note 2: Pin 4 (Vctl) is the DC ground return for the circuit. The LNA is in the high gain mode when a short circuit is introduced to this pin through an external switch. The LNA is in bypass mode when an open circuit is introduced. For the data presented, switching is done through a two position DIP switch (J5) in series with a 2 Ohm resistor (to account for the Ron of an electrical switch). Note 3: L1, L2 and C1 should be located as close to pins as possible. 8 - 138 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz Evaluation PCB 8 AMPLIFIERS - SMT List of Material Item J1 - J2 J3 - J4 J5 C1 C2 C3 L1 L2 R1 U1 PCB* Description PC Mount SMA RF Connector DC Pin 2 Pos DIP Switch 10000 pF Capacitor, 0402 Pkg. 10000 pF Capacitor, 0603 Pkg. 1000 pF Capacitor, 0402 Pkg. 19 nH Inductor, 0402 Pkg. 18 nH Inductor, 0603 Pkg. 2 Ohm Resistor, 0402 Pkg. HMC373LP3 Amplifier 107177 Evaluation Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. * Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 8 - 139 v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz 8 AMPLIFIERS - SMT Application Circuit Note 1: Choose value of capacitor C1 for low frequency bypassing. A 0.01 F 10% capacitor is recommended. Note 2: Pin 4 (Vctl) is the DC ground return for the circuit. The LNA is in the high gain mode when a short circuit is introduced to this pin through an external switch. The LNA is in bypass mode when an open circuit is introduced. For the data presented, switching is done through a two position DIP switch (J5) in series with a 2 Ohm resistor (to account for the Ron of an electrical switch). Note 3: L1, L2 and C1 should be located as close to pins as possible. 8 - 140 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0604 MICROWAVE CORPORATION HMC373LP3 GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 700 - 1000 MHz Notes: 8 AMPLIFIERS - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 8 - 141 |
Price & Availability of HMC373LP3
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |