View APL5301_379149.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

APL5301/2
Low IQ, Low Dropout 300mA Fixed Voltage Regulator
Features
* * * * * * * * * * * * * * Low Quiescent Current : 50uA (No load) Low Dropout Voltage : 400mV (VOUT(Nominal)=3.0V Version @300mA) Very low Shutdown Current : < 0.5uA Fixed Output Voltage : 1.3V ~ 5.0V by step 0.1V increment Stable with 1uF Output Capacitor Stable with Aluminum, Tantalum or Ceramic Capacitors . Reverse Current Protection No Protection Diodes Needed Built in Thermal Protection Built in Current Limit Protection Controlled Short Circuit Current : 50mA Fast Transient Response Short Setting Time SOP-8, SOT-23, SOT-23-5, SOT-89, and SOT-89-5 Packages
General Description
The APL5301/2 series are micropower, low noise, low dropout linear regulators, which operate from 3V to 6V input voltage and deliver up to 300mA. Typical dropout voltage is only 260mV at 300mA loading. Designed for use in battery-powered system, the low 50uA quiescent current makes it an ideal choice. Design with an internal P-channel MOSFET pass transistor, the APL5301/2 maintain a low supply current, independent of the load current and dropout voltage. Other features include reverse current protection, thermal-shutdown protection, current limit protection to ensure specified output current and controlled shortcircuit current. The APL5301/2 regulators come in a miniature SOP-8, SOT-23, SOT-23-5, SOT-89 and SOT-89-5 packages.
Pin Configuration
V IN 3 1 2 V OUT
1 2 3 T A B is V IN
G ND
GND
V IN
V OUT
Applications
* * * Notebook Computer PDA or Portable Equipments Noise-Sensitive Instrumentation Systems
SOT-23 (Top View) APL5301
SOT-89 (Top View) APL5301
BP GND SHDN
V OUT GND V IN
1 2 3
5
BP
5 1 2
4 3
4
SHDN V OUT G N D V IN
SOT-23-5 (Top View) APL5301
SOT-89-5 (Top View) APL5301
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004 1 www.anpec.com.tw
APL5301/2
Pin Configuration (Cont.)
G ND
SHDN V IN V OUT BP 1 2 3 4 8 7 6 5 GND
T A B is G N D
V IN 3 1 V OUT 2 V IN GND SHDN
1 2 3
5
VOUT
1 2 3
GND GND GND
4
BP
V OUT GND V IN
SOP-8 (Top View) APL5301
SOT-23 (Top View) APL5302
SOT-23-5 (Top View) APL5302
SOT-89 (Top View) APL5302
Ordering and Marking Information
A P L 5 3 0 1 /2 L e a d F re e C o d e H a n d lin g C o d e Tem p. Range P ackage C ode V o lta g e C o d e P ackage C ode A : S O T -2 3 B : S O T -2 3 -5 D : S O T -8 9 D 5 : S O T -8 9 -5 K : S O P -8 Tem p. Range C : 0 to 7 0 C I : -4 0 to 8 5 C H a n d lin g C d e o TR : Tape & R eel V o lta g e C o d e : 1 3 : 1 .3 V ~ 3 4 : 3 .4 V 5 0 : 5 .0 V L e a d F re e C o d e L : L e a d F re e D e v ic e B la n k : O rig in a l D e vic e
A P L 5 3 0 1 /2 -1 3 D /K :
A P L 5 3 0 1 /2 XXXXX 13
XXXXX
- D a te C o d e
;
1 3 - 1 .3 V
Marking Information
SOT-23 and SOT-23-5 packages Product Name APL5301-13A/B APL5301-14A/B APL5301-15A/B APL5301-16A/B APL5301-17A/B APL5301-18A/B APL5301-19A/B APL5301-20A/B APL5301-21A/B APL5301-22A/B APL5301-23A/B APL5301-24A/B APL5301-25A/B APL5301-26A/B APL5301-27A/B APL5301-28A/B APL5301-29A/B APL5301-30A/B APL5301-31A/B
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
Marking 317X 318X 319X 31AX 31BX 31CX 31DX 31EX 31FX 31GX 31HX 31IX 31JX 31KX 31LX 31MX 31NX 31OX 31PX
2
Product Name APL5302-13A/B APL5302-14A/B APL5302-15A/B APL5302-16A/B APL5302-17A/B APL5302-18A/B APL5302-19A/B APL5302-20A/B APL5302-21A/B APL5302-22A/B APL5302-23A/B APL5302-24A/B APL5302-25A/B APL5302-26A/B APL5302-27A/B APL5302-28A/B APL5302-29A/B APL5302-30A/B APL5302-31A/B
Marking 327X 328X 329X 32AX 32BX 32CX 32DX 32EX 32FX 32GX 32HX 32IX 32JX 32KX 32LX 32MX 32NX 32OX 32PX
www.anpec.com.tw
APL5301/2
Marking Information (Cont.)
SOT-23 and SOT-23-5 packages Product Name APL5301-32A/B APL5301-33A/B APL5301-34A/B APL5301-35A/B APL5301-48A/B APL5301-49A/B APL5301-50A/B
Marking 31QX 31RX 31SX 31TX 31XX 31YX 31ZX Product Name APL5302-32A/B APL5302-33A/B APL5302-34A/B APL5302-35A/B APL5302-48A/B APL5302-49A/B APL5302-50A/B Marking 32QX 32RX 32SX 32TX 32XX 32YX 32ZX
The last character "X" in the marking is for data code.
Pin Description
No. 1 2 3 4 5 PIN Name VIN GND SHDN(Note1) BP(Note1) VOUT I O O I/O I Description Supply voltage input. Ground pins of the circuitry, and all ground pins must be soldered To PCB with proper power dissipation. Shutdown control pin, low = off, high = nromal. Don't leave open. Bypass signal pin of the regulator. Output pin of the regulator.
Note1 : This pin does not exist in 3-pin package.
Absolute Maximum Ratings
Symbol VIN, VOUT SHDN RTH,JA PD TJ Parameter Input Voltage or Out Voltage Shutdown Control Pin Thermal Resistance - Junction to Ambient Power Dissipation Operating Junction Temperature Control Section Power Transistor TSTG TL Storage Temperature Range Lead Temperature (Soldering, 10 second) Rating 6.5 6.5 357 Internally Limited 0 to 125 0 to 150 -65 to +150 260 C C Unit V V C/W W C
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
3
www.anpec.com.tw
APL5301/2
Electrical Characteristics
Unless otherwise noted these specifications apply over full temperature, VIN=3.8V, CIN=COUT=1uF, SHDN=VIN, TJ=0 to 125C. Typical values refer to TJ=25C. APL5301/2 Symbol Parameter Test Conditions Unit Min. Typ. Max.
VIN VOUT ILIMIT Input Voltage Output Voltage Circuit Current Limit VIN=VOUT+0.5V VOUT=0V VIN=VOUT+0.5V VOUT+0.5V< VCC<6.0V, IOUT=150mA VIN =VOUT+0.5V, 0mA< IOUT < IMAX VIN= VOUT+0.5V , IOUT=1mA-150mA in 1us 1.3VVOUT<1.5V 1.5VVOUT<2.0V IOUT =300mA 2.0VVOUT<2.5V 2.5VVOUT<3V 3VVOUT 5V F1kHz, 1Vpp at VIN = VOUT+1.0V No load IOUT=300mA Shutdown = low IOUT=0, VCC=6.0V 100HzISHORT Short Current IOUT Load Current REGLINE Line Regulation REGLOA Load Regulation Load Transient
VDROP Dropout Voltage
(Note2)
V
PSRR Ripple Rejection IQ Quiescent Current Shutdown Supply (Note3) Current Noise
45
dB A A Vrms ms C C ppm/C 2.6 1 2.5 F Ohm V
Shutdown Recovery CBP=0.01uF,COUT=1uF, no load (Note3) Delay OTS Over Temperature Shutdown Over Temperature Shutdown Hysteries Hysteresis TC Output Voltage Temperature Coefficient 0.8 0.02 VOUT+1.0V< VIN <6.0V 0.4
50 1.0 0.1 1.6
COUT Output Capacitor ESR Shutdown Input (Note3) Threshold
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
4
www.anpec.com.tw
APL5301/2
Electrical Characteristics (Cont.)
Symbol ISHDN Parameter Shutdown input Bias current(Note3) Input Reverse Leakage current Reverse Protection Threshold Test Conditions VSHDN =VIN VOUT-VIN=0.1V APL5301/2 Min. Typ. 0.01 0.1 11 Max. 100 0.5 50 Unit nA A mV
Note2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT+ 0.5V Note3 : For 5-pin devices only.
Application Circuit
IN P U T 2 .7 V to 6 V V IN A P L 5 3 0 1 /2 on o ff C BP 0 .0 1 u F SHDN GND BP C OUT 1uF V OUT VO UT
C IN 1uF
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
5
www.anpec.com.tw
APL5301/2
Typical Characteristics
(All Curves are For Fix 3.3V) Output Voltage vs. Temperature
3.32
Ground Pin Current vs. Load Current
Ground Pin Current vs. Load Current (uA)
160 140 120 100 80 60 40 20 0 0 50 100 150 200 250 300
Output Voltage (V)
3.31
3.3
3.29
3.28 -40
-15
10
35
60
85
Temperature (C )
Load Current (mA)
Ground Pin Current vs. Load Current (uA)
Ground Pin Current vs. Input Voltage
160 140 120 100 80 60 40 20 0 0 1 2 3 4 5 6 3.5
Input Voltage vs. Output Voltage
IOUT=50mA
3
Output Voltage (V)
2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 6
NO LOAD
Input Voltage (V)
Input Voltage (V)
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
6
www.anpec.com.tw
APL5301/2
Typical Characteristics
Dropout Voltage vs. Load Current
300
Reverse Leakage Current vs. Output Voltage
1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0
250
200
150
100
50
0 0 50 100 150 200 250 300
Reverse Leakage Current (uA)
Dropout Voltage (mV)
0
1
2
3
4
5
6
Load Current (mA)
Output Voltage (V)
SHDN Threshold Voltage vs. Input Voltage
1.6
+ 0 -1 0 -2 0
PSRR vs. Frequency
SHDN Threshold Voltage (V)
1.5
1.4
PSRR (dB)
-3 0 -4 0 -5 0 -6 0
1.3
VIN=4.3V IOUT =50mA COUT=1uF CBP=0.1uF
1.2
1.1
-7 0 -8 0
1 3.5 4 4.5 5 5.5 6
10
20
50 100 200
500
1k
2k
5k
10k 20k
50k
200 k
Input Voltage (V)
Frequency (HZ)
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
7
www.anpec.com.tw
APL5301/2
Typical Characteristics
Line-Transient Response
VOUT
Load-Transient Response
VOUT
Output Voltage (20mV/div)
VIN=4.3V IOUT
Output Voltage (50mV/div)
5V 4V
50mA
IOUT=50mA VIN
1mA
Time (100us)
Time (500us/div)
Entering Shutdown
Shutdown Exit Delay
2.5V
SHDN
SHDN
CBP=0.01uF
0V
VOUT VOUT
0V
Time (0.1ms/div)
Time (0.1ms/div)
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
8
www.anpec.com.tw
APL5301/2
Typical Characteristics
Region of Stable ESR vs. Load Current
10
Recommended Minimum Footprint
Stable Region
1
COUT=1uF
COUT ESR ()
0.1
0.01 0 50 100 150 200
Untested
250 300
Load Current (mA)
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
9
www.anpec.com.tw
APL5301/2
Application Information
Capacitor Selection and Regulator Stability
The APL5301/2 use at least a 1uF capacitor on the input, and this capacitor can be Aluminum, Tantalum or Ceramic capacitor. The input capacitor with larger value and lower ESR provides better PSRR and linetransient response. The output capacitor also can use Aluminum, Tantalum or Ceramic capacitor, and a minimum value of 1uF and ESR above 0.06 is recommended. The curve of the stable region in typical characteristics shows the appropriate output capacitor ESR for different load current stable operation. A larger output capacitor can reduce noise and improve load-transient response, stability, and PSRR. Note that some ceramic dielectrics exhibit large capacitance and ESR variation with temperature. When using this capacitor, a minimum 2.2uF or more may be required to ensure the stability at low temperature operation. Use a bypass capacitor at BP pin for low output noise. Increasing the capacitance will slightly decrease the output noise, but increase the start-up time. (See Shutdown Exit Delay and Output Noise vs.Bypass Capacitor graph in the typical characteristics) tery-powered systems, this will determine the useful end-of-life battery voltage. Because the APL5301/2 use a p-channel MOSFET pass transistor, the dropout voltage is a function of drain-to-source on-resistance (RDS(ON)) multiplied by the load current.
Reverse Current Protection
The APL5301/2 have an internal reverse protection, it does not need an external schottky diode to connect the regulator input and output. If the output voltage is forced above the input voltage by more than 11mV, the IC will be shutdown and the ground pin current is below 0.1uA.
Shutdown/Enable
The APL5301/2 have an active high enable function. Force EN high (>1.6V) enables the regulator, EN low (<0.4V) disables the regulator and enter the shutdown mode. In shutdown mode, the quiescent current can reduce below 1uA. The EN pin cannot be floating, a floating EN pin may cause an indeterminate state on the output. If it is no use, connect to VIN for normal operation.
Load-Transient Considerations Current Limit
The APL5301/2 load-transient response graphs in typical characteristics show the transient response. A step change in the load current from 1mA to 50mA at 1us will cause a 60mV transient spike. Larger output capacitor and lower ESR can reduce transient spike. The APL5301/2 have a current limit protection. The ouptut voltage will drop close to zero volt, when load current reaches the limit, and then the load current will be limited at 50mA after output voltage is below 0. 7V. When the load current back to the value where limiting started, the output voltage and current will return to normal value. When output is shorted to ground, the APL5301/2 will keep short circuit current at 150mA .
10 www.anpec.com.tw
Input-Output (Dropout)Voltage
The minimum input-output voltage difference (dropout) determines the lowest usable supply voltage. In bat
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
APL5301/2
Thermal Protection
Thermal protection limits total power dissipation in the device. When the junction temperature exceeds TJ=+150C, the thermal sensor generates a logic signal to turn off the pass transistor and allows IC to cool. When the IC's junction temperature is down by 10C, the thermal sensor will turn the pass transistor on again, resulting in a pulsed output during continuous thermal protection. Thermal protection is designed to protect the APL5301/2 in the event of fault conditions. For continuous operation, do not exceed the absolute maximum junction temperature of TJ=+150C.
Operating Region and Power Dissipation
The thermal resistance of the case to circuit board, and the rate of air flow all control the APL5301/2's maximum power dissipation. The power dissipation across the device is PD = IOUT (VIN-VOUT) and the maximum power dissipation is: PDMAX = (TJ-TA) / (JC +CA) where TJ-TA is the temperature difference between the junction and ambient air, JC is the thermal resistance of the package, and CA is the thermal resistance through the printed circuit board, copper traces, and other materials to the ambient air. The GND pin of the APL5301 and APL5302 that the packages ard SOT-23-5, SOT-89-5 AND SOP-8 provide an electrical connection to ground and channeling heat away. If power dissipation is large, connect the GND pin to ground using a large pad or ground plane, can improve the problem of over heat of IC.
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
11
www.anpec.com.tw
APL5301/2
Packaging Information
SOP-8 pin ( Reference JEDEC Registration MS-012)
E
H
e1 D
e2
A1
A
1 L
0.004max.
Dim A A1 D E H L e1 e2 1
Mi ll im et er s Min. 1. 35 0. 10 4. 80 3. 80 5. 80 0. 40 0. 33 1. 27B S C 8 Max . 1. 75 0. 25 5. 00 4. 00 6. 20 1. 27 0. 51 Min. 0. 053 0. 004 0. 189 0. 150 0. 228 0. 016 0. 013
0.015X45
Inche s Max . 0. 069 0. 010 0. 197 0. 157 0. 244 0. 050 0. 020 0. 50B S C 8
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
12
www.anpec.com.tw
APL5301/2
Packaging Information
SOT-23
D B
3 E 1 2 H
S e
A
A1
L
C
Dim A A1 B C D E e H L
M illim et er s M in. 1. 0 0 0. 0 0 0. 3 5 0. 1 0 2. 7 0 1. 4 0 1. 9 0 B SC 2. 4 0 0. 3 7 3. 0 0 0. 0 94 0. 0 01 5 M ax. 1. 3 0 0. 1 0 0. 5 1 0. 2 5 3. 1 0 1. 8 0 M in. 0. 0 39 0. 0 00 0. 0 14 0. 0 04 0. 1 06 0. 0 55
Inc he s M ax. 0. 0 51 0. 0 04 0. 0 20 0. 0 10 0. 1 22 0. 0 71 0. 0 75 B SC 0. 11 8
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
13
www.anpec.com.tw
APL5301/2
Packaging Information
SOT-23-5
e1
5
4 E1 E
1
2
3
e
b
D
A2
A
a
L1
A1
L2
L
Dim A A1 A2 D E E1 L L1 L2 N
Mi ll imet er s Min . 0. 9 5 0. 0 5 0. 9 0 2. 8 2. 6 1. 5 0. 3 5 0. 2 0 BSC 0. 5 5 0 10 0 0. 7 0. 0 20 Ma x . 1. 4 5 0. 1 5 1. 3 0 3. 0 0 3. 0 0 1. 7 0 0. 5 5 Min . 0. 0 37 0. 0 02 0. 0 35 0. 11 0 0. 1 02 0. 0 59 0. 0 14
Inc hes Ma x . 0. 0 57 0. 0 06 0. 0 51 0. 11 8 0. 11 8 0. 0 67 0. 0 22 0. 0 08 B SC 0. 0 28 5 10
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
14
www.anpec.com.tw
APL5301/2
Packaging Information
SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62)
D
D1
a E H 1 2 3
L B1 B e e1 C
A a
D im A B B1 C D D1 e e1 E H L
M illim eters M in. 1.40 0.40 0.35 0.35 4.40 1.35 1.50 B SC 3.00 B SC 2.29 3.75 0.80 2.60 4.25 1.20 10 0.090 0.148 0.031 M ax. 1.60 0.56 0.48 0.44 4.60 1.83 M in. 0.055 0.016 0.014 0.014 0.173 0.053
Inches M ax. 0.063 0.022 0.019 0.017 0.181 0.072 0.059 BSC 0.118 B SC 0.102 0.167 0.047 10
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
15
www.anpec.com.tw
APL5301/2
Packaging Information
SOT-89-5
Dim A B C D E F G H I J K L
M illim eters M in. 4.40 4.05 1.50 1.30 2.40 0.80 3.00 REF 1.50 REF 0.40 1.40 0.35 5 TYP 0.52 1.60 0.41 0.01 0.05 0.01 M ax. 4.60 4.25 1.70 1.50 2.60 M in. 0.17 0.16 0.06 0.05 0.09 0.03
Inches M ax. 0.18 0.17 0.07 0.06 0.1 0.12 REF 0.06 REF 0.02 0.06 0.02 0.2 TYP
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
16
www.anpec.com.tw
APL5301/2
Physical Specifications
Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Reflow Condition
TP
(IR/Convection or VPR Reflow)
tp C ritical Zone T L to T P
R am p-up
T e m p e ra tu re
TL T sm ax
tL
T sm in R am p-down ts Preheat
25
t 25 C to Peak
T im e
Classificatin Reflow Profiles
Profile Feature Sn-Pb Eutectic Assembly Large Body Small Body Pb-Free Assembly Large Body Small Body 3C/second max. 150C 200C 60-180 seconds 3C/second max 217C 60-150 seconds 245 +0/-5C 250 +0/-5C 10-30 seconds 20-40 seconds
Average ramp-up rate 3C/second max. (TL to TP) Preheat - Temperature Min (Tsmin) 100C - Temperature Mix (Tsmax) 150C - Time (min to max)(ts) 60-120 seconds Tsmax to TL - Ramp-up Rate Tsmax to TL - Temperature(TL) 183C - Time (tL) 60-150 seconds Peak Temperature(Tp) 225 +0/-5C 240 +0/-5C Time within 5C of actual Peak 10-30 seconds 10-30 seconds Temperature(tp) Ramp-down Rate 6C/second max. 6 minutes max. Time 25C to Peak Temperature
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004 17
6C/second max. 8 minutes max.
www.anpec.com.tw
Note: All temperatures refer to topside of the package. Measured on the body surface.
APL5301/2
R e lia b ilit y te s t p r o g r a m
Te s t ite m S O L D E R A B IL IT Y H O LT PCT TST ESD L a tc h -U p M e th o d M IL -S T D -8 8 3 D -2 0 0 3 M IL -S T D -8 8 3 D -1 0 0 5 .7 J E S D -2 2 - B , A 1 0 2 M IL -S T D -8 8 3 D -1 0 11 .9 M IL -S T D -8 8 3 D -3 0 1 5 .7 JESD 78 D e s c rip tio n 2 45 C , 5 S E C 1 0 0 0 H rs B ia s @ 1 2 5 C 1 6 8 H rs , 1 0 0 % R H , 1 2 1 C -6 5 C ~ 1 5 0 C , 2 0 0 C y c le s V H B M > 2 K V, V M M > 2 0 0 V 1 0 m s , I tr > 1 0 0 m A
Carrier Tape
t P P1 D
Po E
F W
Bo
Ao
Ko D1
T2
J C A B
T1
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
18
www.anpec.com.tw
APL5301/2
Reel Dimensions
A p p lic a tion A 3 30 1 SOP- 8 F 5 .5 1 A p p lic a tion A 1 78 1 S O T-89 F 5 .5 0 .05 A p p lic a tion A 1 78 1 S O T-23 -5 F 3 .5 0 .05 B 6 2 + 1.5 D C 1 2.7 5+ 0 .1 5 D1 J 2 0 .5 Po 4 .0 0 .1 J 3 0 .1 5 Po 4 .0 0 .1 J T1 1 2.4 0.2 P1 2 .0 0 .1 T1 14 2 P1 2 .0 0 .1 T1 8 .4 2 P1 2 .0 0 .1 T2 2 0 .2 Ao 6 .4 0 .1 T2 1 .3 0 .3 Ao 4 .8 0 .1 T2 1 .5 0 .3 Ao 3 .1 5 0.1 W 12 0. 3 Bo 5 .2 0 . 1 W 1 2 + 0.3 1 2 - 0 .1 Bo 4 .5 0 .1 W 8 .0 + 0.3 - 0.3 Bo 3 .2 0 .1 P 8 0 .1 Ko 2 .1 0 .1 P 8 0 .1 Ko 1 .8 0 0 .1 P 4 0 .1 Ko 1 .4 0 .1 E 1 .7 50 .1 t 0 .3 0 .01 3 E 1 .7 5 0 .1 t 0 .3 0 .01 3 E 1 .7 5 0 .1 t 0 .2 0 .03
1 .5 5 +0.1 1 .5 5 + 0.2 5 B 70 2 D 1 .5 0 .1 B 7 2 1 .0 D 1 .5 + 0.1 C 1 3.5 0.15 D1 1 .5 0 .1 C
1 3.0 + 0 .2 2 .5 0 .15 D1 1 .5 + 0.1 Po 4 .0 0 .1
(mm)
Cover Tape Dimensions
Application SOP- 8 SOT- 23 SOT- 89 Carrier Width 12 8 12 Cover Tape Width 9.3 5.3 9.3 Devices Per Reel 2500 3000 1000
Customer Service
Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369
Copyright ANPEC Electronics Corp. Rev. B.1 - Mar., 2004
19
www.anpec.com.tw

▲Up To Search▲

Price & Availability of APL5301

	To Download APL5301 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .