View BUK124-50L_370574.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
DESCRIPTION
Monolithic logic level protected power MOSFET using TOPFET2 technology assembled in a 5 pin surface mounting plastic package.
BUK124-50L
QUICK REFERENCE DATA
SYMBOL VDS ID Ptot Tj RDS(ON) SYMBOL VPS PARAMETER Continuous drain source voltage Continuous drain current Total power dissipation Continuous junction temperature Drain-source on-state resistance PARAMETER Protection supply voltage MAX. 50 30 90 150 28 NOM. 5 UNIT V A W C m UNIT V
APPLICATIONS
General purpose switch for automotive systems and other applications.
FEATURES
TrenchMOS output stage with low on-state resistance Separate input pin for higher frequency drive 5 V logic compatible input Separate supply pin for logic and protection circuits with low operating current Overtemperature protection Drain current limiting Short circuit load protection Latched overload trip state reset by the protection pin Diagnostic flag pin indicates protection supply connected, overtemperature condition,overload tripped state, or open circuit load (detected in the off-state) ESD protection on all pins Overvoltage clamping
FUNCTIONAL BLOCK DIAGRAM
PROTECTION SUPPLY DRAIN
FLAG
OC LOAD DETECT
O/V CLAMP
INPUT
POWER RIG MOSFET
LOGIC AND PROTECTION
SOURCE
Fig.1. Elements of the TOPFET.
PINNING - SOT263B-01
PIN 1 2 3 4 5 tab Input Flag Drain Protection supply DESCRIPTION
PIN CONFIGURATION
mb mb
SYMBOL
D TOPFET P F I
P
12345
Source Drain
Front view
MBL267
S
Fig. 2.
Fig. 3.
January 2003
1
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum Rating System (IEC 134) SYMBOL VDS ID II IF IP Ptot Tstg Tj Tsold PARAMETER Continuous voltage Drain source voltage1 Continuous currents Drain current Input current Flag current Protection supply current Thermal Total power dissipation Storage temperature Junction temperature2 Mounting base temperature Tmb = 25C continuous during soldering -55 VPS = 5 V; Tmb = 25C VPS = 0 V; Tmb = 85C -5 -5 -5 VIS = 0 V CONDITIONS MIN.
BUK124-50L
MAX. 50 self limited 30 5 5 5 90 175 150 260
UNIT V A A mA mA mA W C C C
ESD LIMITING VALUE
SYMBOL VC PARAMETER Electrostatic discharge capacitor voltage CONDITIONS Human body model; C = 250 pF; R = 1.5 k MIN. MAX. 2 UNIT kV
OVERLOAD PROTECTION LIMITING VALUE
With an adequate protection supply connected, TOPFET can protect itself from two types of overload overtemperature and short circuit load. SYMBOL PARAMETER Overload protection3 VDS Drain source voltage For overload conditions an n-MOS transistor turns on between the input and source to quickly discharge the power MOSFET gate capacitance. REQUIRED CONDITION protection supply VPS 4 V 0 35 V The drain current is limited to reduce dissipation in case of short circuit load. Refer to OVERLOAD CHARACTERISTICS. MIN. MAX. UNIT
OVERVOLTAGE CLAMPING LIMITING VALUES
At a drain source voltage above 50 V the power MOSFET is actively turned on to clamp overvoltage transients. SYMBOL EDSM EDRM PARAMETER Inductive load turn off Non-repetitive clamping energy Repetitive clamping energy CONDITIONS IDM = 20 A; VDD 20 V Tmb = 25C Tmb 95C; f = 250 Hz 350 45 mJ mJ MIN. MAX. UNIT
1 Prior to the onset of overvoltage clamping. For voltages above this value, safe operation is limited by the overvoltage clamping energy. 2 A higher Tj is allowed as an overload condition but at the threshold Tj(TO) the over temperature trip operates to protect the switch. 3 All control logic and protection functions are disabled during conduction of the source drain diode. If the protection circuit was previously latched, it would be reset by this condition.
January 2003
2
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
THERMAL CHARACTERISTIC
SYMBOL Rth j-mb PARAMETER Thermal resistance Junction to mounting base 1.2 CONDITIONS MIN.
BUK124-50L
TYP.
MAX. 1.39
UNIT K/W
OUTPUT CHARACTERISTICS
Limits are for -40C Tmb 150C; typicals are for Tmb = 25C unless otherwise specified. SYMBOL V(CL)DSS IDSS PARAMETER Off-state Drain-source clamping voltage Drain source leakage current On-state RDS(ON) Drain-source resistance
1
CONDITIONS VIS = 0 V ID = 10 mA IDM = 4 A; tp 300 s; 0.01 VPS = 0 V; VDS = 40 V Tmb = 25C
MIN. 50 50 -
TYP. 60 0.1 21
MAX. 70 70 100 10 50 28
UNIT V V A A m m
tp 300 s; 0.01; VPS 4 V IDM = 10 A; VIS 4.4 V Tmb = 25C
INPUT CHARACTERISTICS
Limits are for -40C Tmb 150C; typicals are for Tmb = 25C unless otherwise specified. SYMBOL VIS(TO) IIS V(CL)IS RIG IISL PARAMETER Normal operation Input threshold voltage2 Input current Input clamping voltage Internal series resistance Input current
3
CONDITIONS ID = 1 mA VIS = 5 V II = 1 mA to gate of power MOSFET VPS 4 V VIS = 5 V
MIN. 0.6 1.1 5.5 1
TYP. 1.6 16 6.4 1.7 2.7
MAX. 2.6 2.1 100 8.5 4
UNIT V V A V k mA
Tmb = 25C
Overload protection latched
1 The drain current required for open circuit load detection is switched off when there is no protection supply, in order to ensure a low off-state quiescent current. Refer to OPEN CIRCUIT LOAD DETECTION CHARACTERISTICS. 2 The measurement method is simplified if VPS = 0 V, in order to distinguish ID from IDSP. Refer to OPEN CIRCUIT LOAD DETECTION CHARACTERISTICS. 3 This is not a directly measurable parameter.
January 2003
3
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
PROTECTION SUPPLY CHARACTERISTICS
Limits are for -40C Tmb 150C; typicals are for Tmb = 25C. SYMBOL VPSF PARAMETER Protection & detection Threshold voltage1 Normal operation or protection latched Supply current Clamping voltage Overload protection latched VPSR tpr Reset voltage Reset time VPS 1 V 1 10 1.8 45 IF = 100 A; VDS = 5 V 2.5 CONDITIONS MIN.
BUK124-50L
TYP. 3.45
MAX. 4
UNIT V A V
IPS, IPSL V(CL)PS
VPS = 4.5 V IP = 1.5 mA
5.5
210 6.5
450 8.5
3 120
V s
OPEN CIRCUIT LOAD DETECTION CHARACTERISTICS
An open circuit load condition can be detected while the TOPFET is in the off-state. Refer to TRUTH TABLE. VPS = 5 V. Limits are for -40C Tmb 150C and typicals are for Tmb = 25C. SYMBOL IDSP VDSF VISF PARAMETER Off-state drain current
2 3
CONDITIONS VIS = 0 V; 2 V VDS 40 V VIS = 0 V ID = 100 A
4
MIN. 0.9 0.2 0.3
TYP. 1.8 1 0.8
MAX. 2.7 2 1.1
UNIT mA V V
Drain threshold voltage Input threshold voltage
OVERLOAD CHARACTERISTICS
Tmb = 25C unless otherwise specified. SYMBOL ID PARAMETER Short circuit load Drain current limiting Overload protection PD(TO) TDSC Overload power threshold Characteristic time Overtemperature protection Threshold temperature CONDITIONS VPS > 4 V VIS = 5 V; VPS > 4 V device trips if PD > PD(TO) which determines trip time
5
MIN. -40C Tmb 150C 28.5
TYP. 44
MAX. 60
UNIT A
75 250
185 380
250 600
W s
Tj(TO)
VPS = 5 V from ID 4 A or VDS > 0.2 V
150
170
-
C
1 When VPS is less than VPSF the flag pin indicates low protection supply voltage. Refer to TRUTH TABLE. 2 The drain source current which flows in a normal load when the protection supply is high and the input is low. 3 If VDS < VDSF then the flag indicates open circuit load. 4 For open circuit load detection, VIS must be less than VISF. 5 Trip time td sc varies with overload dissipation PD according to the formula td sc TDSC / ln[ PD / PD(TO)].
January 2003
4
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
TRUTH TABLE
For normal, open-circuit load and overload conditions or inadequate protection supply voltage. Assumes proper external pull-up for flag pin. Refer to FLAG CHARACTERISTICS. CONDITION Normal on-state Normal off-state Open circuit load Open circuit load Short circuit load1 Over temperature Low protection supply voltage Low protection supply voltage PROTECTION 1 1 1 1 1 1 0 0 KEY `0' equals low `1' equals high `X' equals don't care. INPUT 1 0 1 0 1 X 1 0 FLAG 0 0 0 1 1 1 1 1
BUK124-50L
OUTPUT ON OFF ON OFF OFF OFF ON OFF
FLAG CHARACTERISTICS
The flag is an open drain transistor which requires an external pull-up circuit. Limits are for -40C Tmb 150C; typicals are for Tmb = 25C. SYMBOL VFSF IFSF IFSO V(CL)FS RF PARAMETER Flag `low' Flag voltage Flag saturation current Flag `high' Flag leakage current Flag clamping voltage Application information Suitable external pull-up resistance VFF = 5 V 47 k CONDITIONS normal operation; VPS = 5 V IF = 100 A VFS = 5 V overload or fault VFS = 5 V IF = 100 A 5.5 0.1 6.2 10 8.5 A V 0.8 10 1 V mA MIN. TYP. MAX. UNIT
SWITCHING CHARACTERISTICS
Tmb = 25C; RI = 50 ; RIS = 50 ; VDD = 15 V; resistive load RL = 10 . SYMBOL td on tr td off tf PARAMETER Turn-on delay time Rise time Turn-off delay time Fall time VIS: 5 V 0 V CONDITIONS VIS: 0 V 5 V MIN. TYP. 1.8 3.5 11 5 MAX. 5 8 30 12 UNIT s s s s
1 In this condition the protection circuit is latched. To reset the latch the protection pin must be taken low. Refer to PROTECTION SUPPLY CHARACTERISTICS.
January 2003
5
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
CAPACITANCES
Tmb = 25 C; f = 1 MHz SYMBOL Ciss Coss Crss Cpso Cfso PARAMETER Input capacitance Output capacitance Reverse transfer capacitance Protection supply pin capacitance Flag pin capacitance CONDITIONS VDS = 25 V; VIS = 0 V VDS = 25 V; VIS = 0 V VDS = 25 V; VIS = 0 V VPS = 5 V VFS = 5 V; VPS = 0 V MIN. -
BUK124-50L
TYP. 710 370 26 22 12
MAX. 1050 550 40 -
UNIT pF pF pF pF pF
120 100 80
PD%
Normalise Power Derating
80 70 60 50
ID / A VIS / V = 7 6 5
BUK135-50L
60 40 20
40
4
30 20 10
3
0 0 20 40 60 80
O
0
100
120
140
0
2
4
6
8
10
12
14
16
Tmb / C
VDS / V
Fig.4. Normalised limiting power dissipation. PD% = 100PD/PD(25C) = f(Tmb)
Fig.6. Typical output characteristics, Tj = 25C. ID = f(VDS); parameter VIS; tp = 300 s & tp < td sc
y
40
ID / A
BUK135-50L
80 70
ID / A
BUK135-50L VIS / V =
30
60 50
7 6 5 4 3 2
20
40 30
10
20 10
0 0 20 40 60 80 100 120 140
0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
2.2
Tmb / C
O
VDS / V
Fig.5. Continuous drain current. ID = f(Tamb); condition: VIS = 5 V
Fig.7. Typical on-state characteristics, Tj = 25C. ID = f(VDS); parameter VIS; tp = 300 s
January 2003
6
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
BUK124-50L
2 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0
a
Normalised R
DS(ON) =
f(T j )
200
Tj (TO) C Data below 4V is for information only. All spec. values are for normal operation at 4V and above.
O
BUK135-50L
190
180
170
160
150
-50 0 50 100 150
Tj / C
O
3
4
5
VPS / V
6
7
8
Fig.8. Normalised drain-source on-state resistance. a = RDS(ON)/RDS(ON)25C = f(Tj); ID = 10 A; VIS = 4.4 V
Fig.11. Typical overtemperature protection threshold. Tj(TO) = f(VPS); conditions: VIS = 5 V
IDSS / A
50
RDS(ON) / mOhm
BUK135-50L
100E-6
BUK135-50L
40
10E-6
max.
30
1E-6
max. typ.
100E-9
typ.
20
10
10E-9
0 0 1 2 3
1E-9
VIS / V
4
5
6
7
8
-50
0
50
100
150
Tj / C
O
Fig.9. Typical on-state resistance, Tj = 25C. RDS(ON) = f(VIS); conditions: ID = 10 A; VPS = 4 V; tp = 300 s
ID / A
80 70 60 50 40
Fig.12. Typical drain source leakage current. IDSS = f(Tj); conditions: VDS = 40 V; VPS = VIS = 0 V
IIS / mA
y
BUK135-50L
3.5 3.0 2.5 2.0 1.5
BUK135-50L
VDS = 13V
30 20 10 0 0 1 2 3 4 5 6 7 8
1.0
Latched Unlatched
0.5 0 0 1 2 3
VIS / V
VIS / V
4
5
6
7
Fig.10. Typical transfer characteristics, Tj = 25C. ID = f(VIS); conditions: VPS 4 V tp = 300 s
Fig.13. Typical DC input characteristics, Tj = 25C. IIS & IISL = f(VIS); normal operation & protection latched
January 2003
7
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
BUK124-50L
10E-3
IIS & I ISL
BUK135-50L
2.5
IDSP / mA
BUK135-50L
IISL
2.0
1E-3
1.5
00E-6
1.0
IDSP is constant from Vds = 2V to 40V
IIS
0.5
10E-6 -50 0 50 O Tj / C 100 150
0 0 1 2
VDS / V
3
4
5
Fig.14. Typical DC input currents. IIS & IISL = f(Tj); normal & latched; conditions: VIS = 5 V; VPS = 5 V
Fig.17. Off state drain current characteristic. IDSP = f(VDS); conditions: Tj = 25C; VPS = 5 V; VIS = 0 V
3.0 2.5 2.0 1.5 1.0
VIS(TO) / V
BUK135-50L
2.5
IDSP / mA
BUK135-50L
2.0
max .
1.5
typ.
1.0
min.
0.5 0.0 -50 0 50 100
O
0.5
150
0 0 1 2 3
Tj / C
VPS / V
4
5
6
7
8
Fig.15. Input threshold voltage. VIS(TO) = f(Tj); conditions: ID = 1 mA; VDS = 5 V
Fig.18. Off state drain current vs protection supply. IDSP = f(VPS); Tj = 25C; VDS = 13 V; VIS = 0 V
10 8 6
IIS / mA
BUK135-50L
2.5
IDSP / mA
BUK135-50L
2.0
4 2 0 0 2
VIS / V
1.5
4
6
8
-50
0
50
Tj / C
O
100
150
Fig.16. Typical input clamping characteristic. II = f(VIS); normal operation, Tj = 25C
Fig.19. Typical off state drain current IDSP = f(Tj); conditions: VDS = 13 V; VPS = 5 V; VIS = 0 V
January 2003
8
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
BUK124-50L
2
VDSF / V Normal load
BUK135-50L
3.0 2.8 2.6
VPSR / V
BUK135-50L
typ.
1
2.4 2.2 2.0
Open circuit load
1.8 1.6 1.4 1.2
0 -50 0 50 100 150
1.0 -50 0 50 100 150
Tj / C
O
Tj / C
O
Fig.20. Open circuit detection threshold voltage. VDSF = f(Tj); VPS 4 V ; VIS = 0 V
Fig.23. Typical protection reset voltage. VPSR = f(Tj); tlr = 100 s
VISF / V
1.0
BUK135-50L Normal operation
10E-6
IFS / A
BUK135-50L
VPS = 0 or 5V
1E-6
max.
typ.
0.5
typ.
Open circuit detection
00E-9
0 -50 0 50 100 150
10E-9
Tj / C
O
-50
0
50 O Tj / C
100
150
Fig.21. Open circuit input threshold voltage. VISF = f(Tj); VPS 4 V ; ID = 100 A
Fig.24. Typical flag characteristics. IFS = f(Tj); fault & overload operation; VIS = 5 V; VFS = 5 V
2
IPS / mA
BUK135-50L
4.0
VPSF / V
BUK135-50L
3.8
3.6
1
3.4
3.2
0 0 1 2 3
3.0
VPS / V
4
5
6
7
8
-50
0
50
Tj / C
O
100
150
Fig.22. Typical DC protection supply characteristics. IPS = f(VPS); normal or overload operation; Tj = 25 C
Fig.25. Typical protection threshold voltage. VPSF = f(Tj); VDS = 5 V ; IF = 100 A
January 2003
9
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
BUK124-50L
V(CL)DSR VDS VDD 0 ID 0 VIS 0 RI = RIS
RF
P F I
P
VII
+
L VDS
D TOPFET
VDD
RI
D TOPFET P F I
+ VPS
-ID/100
VIS
P
D.U.T. R 01 shunt
S
RIS
S
Fig.26. Clamping energy test circuit, RIS = 100 . 2 EDSM = 0.5 LID V(CL)DSR /(V(CL)DSR - VDD )
Fig.29. Test circuit for resistive load switching times. VIS = 5 V
VIS & V DS / V BUK135-50L VDS
1.2 1.0
EDSM / J
BUK135-50L
16 14
25 C
0.8 0.6 0.4 0.2 0 0.1 1
O
12 10 8
150 C
O
6 4 2 0
VIS
L / mH
10
100
0
5
10
15
20
25 30 Time / s
35
40
45
50
Fig.27. Typical non-repetitive clamping energy. EDSM = f(L); conditions: VIS = 0 V
Fig.30. Typical switching waveforms, resistive load. RL = 10 ; adjust VDD to obtain ID = 1.5 A; Tj = 25C
4
ID / A
BUK135-50L
65
VDSS / V
BUK135-50L
ID =
3
4A
2
10mA
1
0 50
VDS / V
60
60
70
-50
0
50
Tj / C
O
100
150
Fig.28. Typical clamping characteristic, 25C. ID = f(VDS); conditions: VIS = 0 V; tp 300 s
Fig.31. Overvoltage clamping characteristic. VDS = f(Tj); conditions: VIS = 0 V; tp 300 s
January 2003
10
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
BUK124-50L
80 70 60
ID / A
BUK135-50L
10000
Capacitance / pF
BUK135-50L
max.
50 40 30
1000
Ciss
typ.
Coss
100
20 10 0 -50 0 50
min.
Crss
100
150
10 0 10 20
Tj / C
O
VDS / V
30
40
50
Fig.32. Typical overload current, VDS = 5 V. ID = f(Tj); conditions: VIS = 5 V; VPS = 4 V; tp = 300 s
Fig.34. Typical capacitances, Ciss, Coss, Crss. C = f(VDS); conditions: VIS = 0 V; f = 1 MHz
Zth / ( K / W )
15
IS / A
BUK135-50L
BUK135-50L
1E+01
0.5
1E+00
10
0.2 0.1 0.05 0.02
PD tp
D = tp T
1E-01
5
0
T
1E-02
0 0 0.5 1
1E-06
1E-05
1E-04
1E-03
1E-02
1E-01
1E-03 1E+00 1E+01
VSD / V
t/s
Fig.33. Typical reverse diode current, Tj = 25 C. IS = f(VSDS); conditions: VIS = 0 V; tp = 300 s
Fig.35. Transient thermal impedance. Zth j-mb = f(t); parameter D = tp/T
January 2003
11
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
MECHANICAL DATA
Plastic single-ended package; heatsink mounted; 1 mounting hole; 5-lead TO-220 lead form option
BUK124-50L
SOT263B-01
E p1 p A A1 q D1
D
mounting base
L3 R L m L4 L1
1
e b
5
wM
L2
R
Q Q1 Q2
c
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 4.5 4.1 A1 b c 0.7 0.4 D 15.8 15.2 D1 6.4 5.9 E 10.3 9.7 e 1.7 L 9.8 9.7 L1 5.9 5.3 L2 5.2 5.0 L3(1) 2.4 1.6 L4(2) max. 0.5 m 0.8 0.6 p 3.8 3.6 p1 4.3 4.1 q 3.0 2.7 Q 2.0 Q1 4.5 Q2 8.2 R 0.5 w 0.4
1.39 0.85 1.27 0.70
Notes 1. Terminal dimensions are uncontrolled in this zone. 2. Positional accuracy of the terminals is controlled in this zone. OUTLINE VERSION SOT263B-01 REFERENCES IEC JEDEC 5-lead (option) TO-220 EIAJ EUROPEAN PROJECTION ISSUE DATE 01-01-11
Fig.36. SOT263B package1 leadform 263B-01, pin 3 connected to mounting base.
1 Refer to mounting instructions for TO220 envelopes. Epoxy meets UL94 VO at 1/8". Net mass: 2 g
January 2003
12
Rev 1.110
Philips Semiconductors
Product Specification
Logic level TOPFET TO-220 version of BUK135-50L
BUK124-50L
DEFINITIONS
DATA SHEET STATUS DATA SHEET STATUS1 Objective data PRODUCT STATUS2 Development DEFINITIONS This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A
Preliminary data
Qualification
Product data
Production
Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. Philips Electronics N.V. 2003 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
1 Please consult the most recently issued datasheet before initiating or completing a design. 2 The product status of the device(s) described in this datasheet may have changed since this datasheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
January 2003
13
Rev 1.110

▲Up To Search▲

Price & Availability of BUK124-50L

	To Download BUK124-50L Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .