View RK80530RY009256_436782.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

( DataSheet : www..com )
Intel(R) Celeron(R) Processor for the PGA370 Socket up to 1.40 GHz on 0.13 Micron Process
Datasheet
Product Features
s
s s
s s
s
Available at 1.4 GHz, 1.30 GHz, 1.20 GHz, 1.10A GHz, 1A GHz and 900 MHz with 100 MHz system bus 256 KB on-die Level 2 (L2) cache with Error Correcting Code (ECC)) Dual Independent Bus (DIB) architecture: Separate dedicated external System Bus and dedicated internal high-speed cache bus Internet Streaming SIMD Extensions for enhanced video, sound and 3D performance Binary compatible with applications running on previous members of the Intel microprocessor line Dynamic execution micro architecture
s
s s s s s
Power Management capabilities -- System Management mode -- Multiple low-power states Optimized for 32-bit applications running on advanced 32-bit operating systems Flip Chip Pin Grid Array (FC-PGA2) packaging technology Integrated high performance 16 KB instruction and 16 KB data, nonblocking, level one cache Integrated Full Speed level two cache allows for low latency on read/store operations Error-correcting code for System Bus data
The Intel(R) Celeron(R) processor is designed for uni-processor based Value PC desktops and is binary compatible with previous generation Intel architecture processors. The Intel Celeron processor provides good performance for applications running on advanced operating systems such as Windows* 95/98, WindowsNT*, Windows* 2000, WindowsXP* and UNIX*. This is achieved by integrating the best attributes of Intel processors--the dynamic execution performance of the P6 microarchitecture plus the capabilities of MMXTM technology--bringing a balanced level of performance to the Value PC market segment. The Intel Celeron processor offers the dependability you would expect from Intel at an exceptional value. Systems based on Intel Celeron processors also include the latest features to simplify system management and lower the cost of ownership for small business and home environments.
May 2002 Order Number: 298596-004
www..com
www..com
Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The Intel(R) Celeron(R) processor may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by calling 1-800548-4725 or by visiting Intel's website at http://www.intel.com. Copyright (c) Intel Corporation, 2002
Intel, Celeron, MMX, Pentium, and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others.
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Contents
1.0 Introduction......................................................................................................................... 9 1.1 Terminology.........................................................................................................10 1.1.1 Package and Processor Terminology ....................................................10 1.1.2 Processor Naming Convention...............................................................11 Related Documents.............................................................................................12 Processor System Bus and VREF .......................................................................................... 13 Clock Control and Low Power States..................................................................14 2.2.1 Normal State--State 1 ...........................................................................15 2.2.2 AutoHALT Powerdown State--State 2...................................................15 2.2.3 Stop-Grant State--State 3 .....................................................................15 2.2.4 HALT/Grant Snoop State--State 4 ........................................................15 2.2.5 Sleep State--State 5..............................................................................16 2.2.6 Deep Sleep State--State 6 ....................................................................16 2.2.7 Clock Control..........................................................................................17 Power and Ground Pins ......................................................................................17 2.3.1 Phase Lock Loop (PLL) Power...............................................................17 Decoupling Guidelines ........................................................................................18 2.4.1 Processor VCCCORE Decoupling............................................................18 Processor System Bus Clock and Processor Clocking .......................................19 Voltage Identification ...........................................................................................19 Processor System Bus Unused Pins...................................................................21 Processor System Bus Signal Groups ................................................................22 2.8.1 Asynchronous vs. Synchronous for System Bus Signals .......................23 2.8.2 System Bus Frequency Select Signals ..................................................24 Test Access Port (TAP) Connection....................................................................25 Maximum Ratings................................................................................................25 Processor Voltage Level Specifications ..............................................................25 AGTL System Bus Specifications........................................................................30 System Bus Timing Specifications ......................................................................31 BCLK/BCLK# & PICCLK Signal Quality Specifications and Measurement Guidelines ....................................................................................41 AGTL Signal Quality Specifications and Measurement Guidelines.....................42 3.2.1 Overshoot/Undershoot Guidelines .........................................................43 3.2.2 Overshoot/Undershoot Magnitude .........................................................44 3.2.3 Overshoot/Undershoot Pulse Duration...................................................44 3.2.4 Activity Factor .........................................................................................44 3.2.5 Reading Overshoot/Undershoot Specification Tables............................45 3.2.6 Determining if a System Meets the Overshoot/Undershoot Specifications .........................................................................................46 Non-AGTL Signal Quality Specifications and Measurement Guidelines.............47 3.3.1 Overshoot/Undershoot Guidelines .........................................................48 3.3.2 Ringback Specification ...........................................................................48 3.3.3 Settling Limit Guideline...........................................................................49
1.2 2.0 2.1 2.2
Electrical Specifications....................................................................................................13
2.3 2.4 2.5 2.6 2.7 2.8
2.9 2.10 2.11 2.12 2.13 3.0 3.1 3.2
Signal Quality Specifications ............................................................................................41
3.3
Datasheet
3
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
3.4
VTT_PWRGD Signal Quality Specification ......................................................... 49 3.4.1 Transition region .................................................................................... 49 3.4.2 Transition time........................................................................................ 50 3.4.3 Noise ...................................................................................................... 50 Thermal Specifications........................................................................................ 51 4.1.1 THERMTRIP# Requirement................................................................... 51 4.1.2 Thermal Diode........................................................................................ 52 Thermal Metrology .............................................................................................. 52 FC-PGA2 Mechanical Specifications .................................................................. 53 Recommended Mechanical Keep-Out Zones ..................................................... 55 Processor Markings ............................................................................................ 56 Processor Signal Listing...................................................................................... 57 Mechanical Specifications................................................................................... 68 6.1.1 Mechanical Specifications for the FC-PGA2 Package ........................... 68 6.1.2 Boxed Processor Heatsink Weight......................................................... 70 Thermal Specifications........................................................................................ 70 6.2.1 Boxed Processor Cooling Requirements ............................................... 70 6.2.2 Boxed Processor Thermal Cooling Solution Clip ................................... 71 Electrical Requirements for the Boxed Processor............................................... 71 6.3.1 Electrical Requirements ......................................................................... 71 Alphabetical Signals Reference .......................................................................... 73 Signal Summaries ............................................................................................... 80
4.0
Thermal Specifications and Design Considerations......................................................... 51 4.1
4.2 5.0 5.1 5.2 5.3 5.4 6.0 6.1
Mechanical Specifications................................................................................................ 53
Boxed Processor Specifications....................................................................................... 68
6.2
6.3 7.0
Processor Signal Description ........................................................................................... 73 7.1 7.2
4
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
List of Figures
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Integrated Heat Spreader (IHS) ............................................................................ 9 AGTL Bus Topology in a Uniprocessor Configuration.........................................14 Stop Clock State Machine ...................................................................................14 PLL Filter Specification........................................................................................18 Differential/Single-Ended Clocking Example.......................................................19 VTT Power Good and Bus Select Interconnect Diagram .....................................21 BSEL[1:0] Example for a System Design............................................................24 Vcc Static and Transient Tolerance ....................................................................28 Clock Waveform ..................................................................................................36 BCLK/BCLK#, PICCLK, and TCK Generic Clock Waveform ..............................37 System Bus Valid Delay Timings ........................................................................37 System Bus Setup and Hold Timings..................................................................38 System Bus Reset and Configuration Timings....................................................38 Platform Power-On Sequence and Timings ........................................................39 Power-On Reset and Configuration Timings.......................................................39 Test Timings (TAP Connection) ..........................................................................40 Test Reset Timings .............................................................................................40 BCLK/BCLK#, PICCLK Generic Clock Waveform at the Processor Pins ...........42 Low to High AGTL Receiver Ringback Tolerance...............................................43 Maximum Acceptable AGTL Overshoot/Undershoot Waveform .........................47 Non-AGTL Overshoot/Undershoot, Settling Limit, and Ringback ......................47 Noise Estimation .................................................................................................50 Package Dimensions...........................................................................................53 Volumetric Keep-Out ...........................................................................................55 Component Keep-Out .........................................................................................55 Top Side Processor Markings .............................................................................56 Processor Pinout ................................................................................................57 Conceptual Boxed Processor for the PGA370 Socket ........................................68 Comparison between FC-PGA and FC-PGA2 package......................................69 Side View of Space Requirements for the Boxed Processor ..............................69 Dimensions of Mechanical Step Feature in Heatsink Base.................................70 Thermal Airspace Requirement for all Boxed Processor Fan Heatsinks in the PGA370 Socket ........................................................................71 Boxed Processor Fan Heatsink Power Cable Connector Description.................72 Motherboard Power Header Placement Relative to the Boxed Processor..........72
Datasheet
5
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
List of Tables
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Processor Identification....................................................................................... 11 System Bus Clock in Deep Sleep Mode (Differential Mode only) ....................... 16 Voltage Identification Definition .......................................................................... 20 System Bus Signal Groups ................................................................................ 23 Frequency Select Truth Table for BSEL[1:0] ...................................................... 24 Absolute Maximum Ratings ................................................................................ 25 Voltage and Current Specifications..................................................................... 26 Power Supply Current Slew Rate (dIcccore/dt)................................................... 27 Vcc Static & Transient Tolerance........................................................................ 28 AGTL Signal Group Levels Specifications .......................................................... 29 Non-AGTL Signal Group Levels Specifications .................................................. 29 3.3 Volt CMOS Output Signal Group DC Specifications ..................................... 30 Processor AGTL Bus Specifications ................................................................... 30 System Bus Timing Specifications (Single-Ended Clock) ................................... 31 System Bus Timing Specifications (Differential Clock) ....................................... 32 Valid System Bus to Core Frequency Ratios ..................................................... 33 System Bus Timing Specifications (AGTL Signal Group) ................................... 33 System Bus Timing Specifications (CMOS Signal Group) .................................. 33 System Bus Timing Specifications (Reset Conditions) ...................................... 34 System Bus Timing Specifications (APIC Clock and APIC I/O) .......................... 34 System Bus Timing Specifications (TAP Connection) ........................................ 35 Platform Power-On Timings ................................................................................ 36 BCLK (Single-Ended Clock Mode) Signal Quality Specifications for Simulation at the Processor Pins ........................................................................ 41 BCLK/BCLK# (Differential Clock Mode) and PICCLK Signal Quality Specifications for Simulation at the Processor Pins............................................ 41 AGTL Signal Groups Ringback Tolerance Specifications at the Processor Pins .................................................................................................... 42 Example Platform Information............................................................................. 45 100 MHz AGTL Signal Group Overshoot/Undershoot Tolerance ...................... 46 33 MHz CMOS Signal Group Overshoot/Undershoot Tolerance........................ 48 Signal Ringback Specifications for Non-AGTL Signal Simulation at the Processor Pins .................................................................................................... 49 Processor Thermal Design Power ..................................................................... 51 THERMTRIP# Time Requirement....................................................................... 51 Thermal Diode Parameters ................................................................................. 52 Thermal Diode Interface...................................................................................... 52 The Processor Package Dimensions .................................................................. 54 Processor Case Loading Parameters ................................................................. 54 Signal Listing in Order by Signal Name .............................................................. 58 Signal Listing in Order by Pin Number ................................................................ 63 Boxed Processor Fan Heatsink Spatial Dimensions........................................... 70 Fan Heatsink Power and Signal Specifications................................................... 72 Signal Description ............................................................................................... 73 Output Signals..................................................................................................... 80 Input Signals ....................................................................................................... 80 Input/Output Signals (Single Driver).................................................................... 81 Input/Output Signals (Multiple Driver) ................................................................. 82
6
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Revision History
Revision -004 Date May 2002 Description * Added 1.4 GHz processor information; Added Section 3.4, "VTT_PWRGD Signal Quality Specification"; Updated Table 40, "Signal Description" for VCMOS_REF.
Datasheet
7
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
This page is intentionally left blank.
8
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
1.0
Introduction
The Intel(R) Celeron(R) processor based on 0.13 micron process core for the PGA370 socket is the next member of the P6 family, in the Intel IA-32 processor line and hereafter will be referred to as simply "the processor". The processor will continue in the package technology called flip-chip pin grid array but will contain a Integrated Heat Spreader (IHS) (see Figure 1). The flip-chip with IHS package will be labeled as FC-PGA2 and will utilize the same 370-pin zero insertion force socket (PGA370). Thermal solutions contact the IHS directly for the FC-PGA2 package and not to the bare-die as with the FC-PGA attachment. The processor, like its predecessors in the P6 family of processors, implements a Dynamic Execution microarchitecture--a unique combination of multiple branch prediction, data flow analysis, and speculative execution. The processor delivers higher performance than the Intel(R) Celeron(R) processor based on 0.18 micron process core, while maintaining binary compatibility with all previous Intel Architecture processors. The processor also executes Intel(R) MMXTM technology instructions for enhanced media and communication performance just as the predecessor Celeron processor based on 0.18 micron process core. Additionally, the processor executes Streaming SIMD (single-instruction, multiple data) Extensions for enhanced floating point and 3-D application performance. The processor utilizes multiple low-power states such as Stop-Grant, Sleep, and Deep Sleep to conserve power during idle times. The processor includes an integrated on-die, 256KB 8-way set associative level-two (L2) cache. The L2 cache implements the Advanced Transfer Cache Architecture with a 256-bit wide bus. The processor also includes a 16 KB level one (L1) instruction cache and 16 KB L1 data cache. These cache arrays run at the full speed of the processor core. The processor for the PGA370 socket has a dedicated L2 cache bus, thus maintaining the dual independent bus architecture to deliver high bus bandwidth and performance. Memory is cacheable for 64 GB of addressable memory space, allowing significant headroom for desktop systems. Refer to the Specification Update document for this processor to determine the cacheability and cache configuration options for a specific processor. Contact your nearest Intel Sales Representative for the latest Processor Specification Update.
Figure 1. Integrated Heat Spreader (IHS)
FC-PGA2 w/IHS
FC-PGA
The processor will support a lower voltage differential and single-ended clocking for the system bus. The previous generation Intel Celeron processors for the PGA370 socket will function in a platform that supports this processor, if the platform has been designed to be backward compatible. In addition, the processor will not function in a previous generation platform due to incompatible system bus signal levels and clock type. Care must be taken to ensure the correct processors are installed in the correct PGA370 socket platforms.
Datasheet
9
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
1.1
Terminology
In this document, a `#' symbol after a signal name refers to an active low signal. This means that a signal is in the active state (based on the name of the signal) when driven to a low level. For example, when FLUSH# is low, a flush has been requested. When NMI is high, a nonmaskable interrupt has occurred. In the case of signals where the name does not imply an active state but describes part of a binary sequence (such as address or data), the `#' symbol implies that the signal is inverted. For example, D[3:0] = `HLHL' refers to a hex `A', and D[3:0]# = `LHLH' also refers to a hex `A' (H= High logic level, L= Low logic level). The term "system bus" refers to the interface between the processor, system core logic (a.k.a. the chipset components), and other bus agents.
1.1.1
Package and Processor Terminology
The following terms are used often in this document and are explained here for clarification:
* The processor - The entire product including all internal components. * 256k UP processor - The desktop version of the 0.13 micron process processor. Contains
256KB of L2 cache and is uni-processor capable only.
* PGA370 socket - 370-pin Zero Insertion Force (ZIF) socket which a FC-PGA packaged
processor plugs into.
* FC-PGA - Flip Chip Pin Grid Array. The package technology used on processors based on the
0.18 micron process for the PGA370 socket. The FC-PGA package has the processor die exposed.
* FC-PGA2 - Flip Chip Pin Grid Array 2. The package technology used on the processor for the
PGA370 socket. The FC-PGA2 package contains an Integrated Heat Spreader which covers the processor die.
* Advanced Transfer Cache (ATC) - L2 cache architecture used on the Celeron(R) processors.
ATC consists of microarchitectural improvements that provide a higher data bandwidth interface into the processor core that is completely scaleable with the processor core frequency.
* Keep-out zone - The area on or near a FC-PGA packaged processor that system designs can
not utilize.
* Keep-in zone - The area of a FC-PGA packaged processor that thermal solutions may utilize. * Processor - For this document, the term processor is the generic form of the Celeron(R)
processor based on 0.13 micron process core for the PGA370 socket in the FC-PGA2 package.
* Processor core - The processor's execution engine. * Integrated Heat Spreader (IHS) - The Integrated Heat Spreader (IHS) is a metal cover on the
die and it is an integral part of the processor. The IHS promotes heat spreading away from the die backside to ease thermal constraints. The cache and L2 cache are industry designated names.
10
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
1.1.2
Table 1.
Processor Naming Convention
Processor Identification
Processor 1.4 1.30 1.203 1.20 1.10A 1A 900 Core Frequency 1.40 1.30 GHz 1.20 GHz 1.20 GHz 1.10A GHz 1A GHz 900 MHz System Bus Frequency (MHz) 100 100 100 100 100 100 100 L2 Cache Size (Kbytes) 256 256 256 256 256 256 256 L2 Cache Type2 ATC ATC ATC ATC ATC ATC ATC CPUID1 06Bxh 06Bxh 06Bxh 06Bxh 06Bxh 06Bxh 06Bxh
NOTES: 1. Refer to the Intel(R) Celeron(R) Processor Specification Update for the exact CPUID for each processor. 2. ATC = Advanced Transfer Cache. ATC is an L2 Cache integrated on the same die as the processor core. With ATC, the interface between the processor core and L2 Cache is 256-bits wide, runs at the same frequency as the processor core and has enhanced buffering. 3. 1.20 GHz at VccCORE = 1.475 volts and S-Spec number SL5XS.
Datasheet
11
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
1.2
Related Documents
The reader of this specification should also be familiar with material and concepts presented in the following documents 1,2:
Document AP-485, Intel Processor Identification and the CPUID Instruction AP-589, Design for EMI Intel(R) Architecture Software Developer's Manual Volume I: Basic Architecture Volume II: Instruction Set Reference Volume III: System Programming Guide P6 Family of Processors Hardware Developer's Manual IA-32 Processors and Related Products 1999 Databook 370-Pin Socket (PGA370) Design Guidelines PGA370 Heat Sink Cooling in MicroATX Chassis 815 B-step Chipset Platform Design Guide 3 CK-815 Clock Synthesizer/Driver Specification 3 CK-408 Clock Synthesizer/Driver Specification 3 VRM 8.5 DC-DC Converter Design Guidelines 3 Extensions to the Pentium(R) Pro Processor BIOS Writer's Guide Revision 3 Intel(R) Pentium(R) III Processor in the FC-PGA2, 370-pin Package Thermal Design Guidelines3 249660 249659
(R)
Intel Order Number 241618 243334 243193 243190 243191 243192 244001 243565 244410 245025
NOTES: 1. Unless otherwise noted, this reference material can be found on the Intel Developer's Website located at http://developer.intel.com. 2. For a complete listing of Intel Celeron processor reference material, please refer to the Intel Developer's Website at http://developer.intel.com/design/Celeron/. 3. This material is available through an Intel Field Sales Representative.
12
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
2.0
2.1
Electrical Specifications
Processor System Bus and VREF
The processor uses the original low voltage signaling of the Gunning Transceiver Logic (GTL) technology for the system bus. The GTL system bus operates at 1.25V signal levels versus GTL+ which operates at 1.5 V signal levels. The GTL+ signal technology is used by the Intel(R) Pentium(R) Pro, Intel(R) Pentium(R) II and Intel(R) Pentium(R) III processors. Current P6 family processors vary from the Intel(R) Pentium(R) Pro processor in their output buffer implementation. The buffers that drive the system bus signals on the processor are actively driven to VTT for one clock cycle after the low to high transition to improve rise times. These signals are open-drain and require termination to a supply. Because this specification is different from the standard GTL specification, it is referred to as AGTL, or Assisted GTL in this and other documentation related to the processor. AGTL logic and AGTL+ logic are not compatible with each other due to differences with the signal switching levels. The processor cannot be installed into platforms where the chipset only supports the AGTL+ signal levels. For more information on AGTL or AGTL+ routing, please refer to the appropriate platform design guide. AGTL inputs use differential receivers which requires a reference voltage (VREF). VREF is used by the differential receivers to determine if the input signal is a logical 0 or a logical 1. The VREF signal is typically implemented as a voltage divider on the platform. Noise decoupling is critical for the VREF signal. Refer to the platform design guide for the recommended decoupling requirements. Another important item for the AGTL system bus is termination. System bus termination is used to pull each signal to a high voltage level and to control reflections on the transmission line. The processor contains on-die termination resistors that provide termination for one end of the system bus. The other end of the system bus should also be terminated near the chipset by resistors placed on the platform or on-die termination within the chipset. It is recommended that the system bus is implemented using Dual-End Termination (DET) to meet the timings and signal integrity specified by the processor. Figure 2 is a schematic representation of the AGTL bus topology for the processor, when the chipset has does not have ondie termination. Note: The RESET# signal requires a discrete external termination resistor on the system board. The AGTL bus depends on incident wave switching. Therefore, timing calculations for AGTL signals are based on flight time as opposed to capacitive deratings. Analog signal simulations of the system bus, including trace lengths, is highly recommended especially when not following the recommended layout guidelines.
Datasheet
13
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 2. AGTL Bus Topology in a Uniprocessor Configuration
Processor Chipset
I/O
I/O
Note: RESET# requires external termination.
2.2
Clock Control and Low Power States
Processors allow the use of Sleep, and Deep Sleep states to reduce power consumption by stopping the clock to internal sections of the processor, depending on each particular state. See Figure 3 for a visual representation of the processor low power states.
Figure 3. Stop Clock State Machine
HALT Instruction and HALT B us Cycle Generated 2. Auto HALT Power Down State BCLK running. Snoops and interrupts allowed. INIT#, B INIT#, INTR, SM I#, RESET# 1. Norm al State Norm al execution.
STPCLK # Asserted Snoop Event Occurs Snoop Event Serviced S TPCLK# De-asserted STPCLK# Asserted STPCLK# De-asserted
and Stop-Grant State entered from AutoHALT
Snoop Event Occurs Snoop Event S erviced
4. HALT/Grant Snoop S tate BCLK running. Service snoops to caches.
3. Stop Grant State BCLK running. Snoops and interrupts allowed.
SLP# Asserted
SLP # De-asserted
5. Sleep S tate BCLK running. No snoops or interrupts allowed. BCLK Input Stopped BCLK Input Restarted
6. Deep S leep State BCLK stopped. No snoops or interrupts allowed.
PCB757a
For the processor to fully realize the low current consumption of the Stop-Grant, Sleep and Deep Sleep states, a Model Specific Register (MSR) bit must be set. For the MSR at 02AH (Hex), bit 26 must be set to a `1' (this is the power on default setting) for the processor to stop all internal clocks during these modes. For more information, see the Intel Architecture Software Developer's Manual, Volume 3: System Programming Guide.
14
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
2.2.1
Normal State--State 1
This is the normal operating state for the processor.
2.2.2
AutoHALT Powerdown State--State 2
AutoHALT is a power state entered when the processor executes the HALT instruction. The processor transitions to the Normal state upon the occurrence of SMI#, INIT#, or LINT[1:0] (NMI, INTR). RESET# causes the processor to immediately initialize itself. The return from a System Management Interrupt (SMI) handler can be to either Normal Mode or the AutoHALT Power Down state. See the Intel Architecture Software Developer's Manual, Volume III: System Programmer's Guide for more information. FLUSH# is serviced during the AutoHALT state, and the processor will return to the AutoHALT state. The system can generate a STPCLK# while the processor is in the AutoHALT Power Down state. When the system deasserts the STPCLK# interrupt, the processor returns execution to the HALT state.
2.2.3
Stop-Grant State--State 3
The Stop-Grant state on the processor is entered when the STPCLK# signal is asserted. Since the AGTL signal pins receive power from the system bus, these pins should not be driven (allowing the level to return to VTT) for minimum power drawn by the termination resistors in this state. In addition, all other input pins on the system bus should be driven to the inactive state. BINIT# and FLUSH# are not serviced during the Stop-Grant state. RESET# causes the processor to immediately initialize itself, but the processor stays in Stop-Grant state. A transition back to the Normal state occurs with the deassertion of the STPCLK# signal. A transition to the HALT/Grant Snoop state occurs when the processor detects a snoop on the system bus (see Section 2.2.4). A transition to the Sleep state (see Section 2.2.5) occurs with the assertion of the SLP# signal. While in Stop-Grant State, SMI#, INIT#, and LINT[1:0] are latched by the processor, and only serviced when the processor returns to the Normal state. Only one occurrence of each event is recognized and serviced upon return to the Normal state.
2.2.4
HALT/Grant Snoop State--State 4
The processor responds to snoop transactions on the system bus while in Stop-Grant state or in AutoHALT Power Down state. During a snoop transaction, the processor enters the HALT/Grant Snoop state. The processor stays in this state until the snoop on the system bus has been serviced (whether by the processor or another agent on the system bus). After the snoop is serviced, the processor returns to the Stop-Grant state or AutoHALT Power Down state, as appropriate.
Datasheet
15
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
2.2.5
Sleep State--State 5
The Sleep state is a very low power state in which the processor maintains its context, maintains the phase-locked loop (PLL), and has stopped all internal clocks. The Sleep state can only be entered from the Stop-Grant state. Once in the Stop-Grant state, the SLP# pin can be asserted, causing the processor to enter the Sleep state. The SLP# pin is not recognized in the Normal or AutoHALT states. Snoop events that occur while in Sleep State or during a transition into or out of Sleep state will cause unpredictable behavior. In the Sleep state, the processor is incapable of responding to snoop transactions or latching interrupt signals. No transitions or assertions of signals (with the exception of SLP# or RESET#) are allowed on the system bus while the processor is in Sleep state. Any transition on an input signal before the processor has returned to Stop-Grant state will result in unpredictable behavior. If RESET# is driven active while the processor is in the Sleep state, and held active as specified in the RESET# pin specification, then the processor will reset itself, ignoring the transition through Stop-Grant State. If RESET# is driven active while the processor is in the Sleep State, the SLP# and STPCLK# signals should be deasserted immediately after RESET# is asserted to ensure the processor correctly executes the reset sequence. While in the Sleep state, the processor is capable of entering its lowest power state, the Deep Sleep state, by stopping the BCLK input (see Section 2.2.6). Once in the Sleep state, the SLP# pin can be deasserted if another asynchronous system bus event occurs. The SLP# pin has a minimum assertion of one BCLK period.
2.2.6
Deep Sleep State--State 6
The Deep Sleep state is the lowest power state the processor can enter while maintaining context. The Deep Sleep state is entered by stopping the BCLK input (after the Sleep state was entered from the assertion of the SLP# pin). The processor is in Deep Sleep state immediately after BCLK is stopped. BCLK and BCLK# have to be separated by at least 0.2V during the Deep Sleep State. Stopping of the BCLK input lowers the overall current consumption to leakage levels. To re-enter the Sleep state, the BCLK input must be restarted. A period of 1 ms (to allow for PLL stabilization) must occur before the processor can be considered to be in the Sleep state. Once in the Sleep state, the SLP# pin can be deasserted to re-enter the Stop-Grant state. While in Deep Sleep state, the processor is incapable of responding to snoop transactions or latching interrupt signals. No transitions or assertions of signals are allowed on the system bus while the processor is in Deep Sleep state. Any transition on an input signal before the processor has returned to Stop-Grant state will result in unpredictable behavior.
Table 2.
System Bus Clock in Deep Sleep Mode (Differential Mode only)
Symbol VBCLK VBCLK-VBCLK# Parameter BCLK Voltage Level when not active BCLK# Voltage Level when not active Min 0.4 0 Max 1.45 VBCLK - 0.2 Units V V 2 2 Notes1
NOTES: 1. The values in this table are based on differential probe measurement of the Bclk. 2. The DC voltage level specified must be maintained when the system bus clock is not active (e.g., Deep Sleep Mode). VBCLK# has to be 200 mV less than VBCLK.
16
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
2.2.7
Clock Control
BCLK provides the clock signal for the processor and on-die L2 cache. During AutoHALT Power Down and Stop-Grant states, the processor will process a system bus snoop. The processor does not stop the clock to the L2 cache during AutoHALT Power Down or Stop-Grant states. Entrance into the Halt/Grant Snoop state allows the L2 cache to be snooped, similar to the Normal state. When the processor is in Sleep and Deep Sleep states, it does not respond to interrupts or snoop transactions. During the Sleep state, the internal clock to the L2 cache is not stopped. During the Deep Sleep state, the internal clock to the L2 cache is stopped. The internal clock to the L2 cache is restarted only after the internal clocking mechanism for the processor is stable (i.e., the processor has re-entered Sleep state). PICCLK should not be removed during the AutoHALT Power Down or Stop-Grant states. PICCLK can be removed during the Sleep or Deep Sleep states. When transitioning from the Deep Sleep state to the Sleep state, PICCLK must be restarted with BCLK.
2.3
Power and Ground Pins
The operating voltage for the processor is the same for the core and the L2 cache. VCCCORE is defined as the power pins that supply voltage to the processor's core and cache. The Voltage Regulator Module (VRM) or Voltage Regulator are controlled by the five voltage identification (VID) signals driven by the processor. The VID signals specify the voltage required by the processor core. Refer to Section 2.6 for further details on the VID voltage settings. The processor has 74 VCCCORE, 7 VREF, 20 VTT, VCCCMOS1.5, VCCCMOS1.8, VCCCMOS2.0 and 74 VSS inputs. The VREF inputs are used as the AGTL reference voltage for the processor. The VTT inputs (1.25V) are used to provide an AGTL termination voltage to the processor. VCCCMOS1.5 and VCCCMOS1.8 and VCCCMOS2.0 are not voltage input pins to the processor but rather voltage sources for the pullup resistors which are connected to CMOS (non-AGTL) input/output signals driven to/ from the processor. The VSS inputs are ground pins for the processor core and L2 cache. On the platform, all VCCCORE pins must be connected to a voltage island (an island is a portion of a power plane that has been divided, or an entire plane) to minimize any voltage drop that may occur due to trace impedance. It is also highly recommended for the platform to provide either a voltage island or a wide trace for the VTT pins. Similarly, all Vss pins must be connected to a system ground plane. These recommendations can be found in the platform design guide layout section.
2.3.1
Phase Lock Loop (PLL) Power
It is highly critical that phase lock loop power delivery to the processor meets Intel's requirements. A low pass filter is required for power delivery to pins PLL1 and PLL2. This serves as an isolated, decoupled power source for the internal PLL. Refer to the Phase Lock Loop Power section in the appropriate platform design guide for the recommended filter implementation.
Datasheet
17
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 4. PLL Filter Specification
0.2 dB 0 dB -0.5 dB Forbidden Zone
-28 dB
Forbidden Zone
-40 dB
DC
fpeak
1 MHz
66 MHz
force
2.4
Decoupling Guidelines
Due to the large number of transistors and high internal clock speeds, the processor is capable of generating large average current swings between low and full power states. The fluctuations can cause voltages on power planes to sag below their nominal values if bulk decoupling is not adequate. Care must be taken in the board design to ensure that the voltage provided to the processor remains within the specifications listed in Table 7. Failure to do so can result in timing violations (in the event of a voltage sag) or a reduced lifetime of the component (in the event of a voltage overshoot).
2.4.1
Processor VCCCORE Decoupling
The regulator for the VCCCORE input must be capable of delivering the dICCCORE/dt (defined in Table 7) while maintaining the required tolerances (also defined in Table 7). Failure to meet these specifications can result in timing violations (during VCCCORE sag) or a reduced lifetime of the component (during VCCCORE overshoot). The processor requires both high frequency and bulk decoupling on the system motherboard for proper AGTL bus operation. The minimum recommendation for the processor decoupling requirement is listed below. All capacitors should be placed next to and within the PGA370 socket cavity and mounted on the primary side of the motherboard. The capacitors are arranged to minimize the overall inductance between the VCCCORE and Vss power pins. Decoupling Recommendations:
* VCCCORE decoupling: A minimum of sixteen 4.7 uF capacitors in a 1206 package. * VTT decoupling: Twenty 0.1 uF capacitors in 0603 packages. * VREF decoupling: 0.1 uF and 0.001 uF capacitors in 0603 package placed near the VREF pins.
For additional decoupling requirements, refer to the appropriate platform design guide for recommended capacitor component value/quantity and placement.
18
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
2.5
Processor System Bus Clock and Processor Clocking
The processor will implement an auto-detect mechanism that will allow the processor to use either single-ended or differential signaling for the system bus and processor clocking. The processor checks to see if the signal on pin Y33 is toggling. If this signal is toggling then the processor operates in differential mode. Refer to Figure 5 for an example on differential clocking. Resistor values and clock topology are listed in the appropriate platform design guide for a differential implementation. Note: References to BCLK throughout this document will also imply to it's complement signal, BCLK# in differential implementations, and when noted otherwise. Since legacy PGA370 socket platforms use a different single-ended clocking specification than the processor, the processor will not function when placed into these platforms. The BCLK input directly controls the operating speed of the system bus interface. All AGTL system bus timing parameters are specified with respect to the crossing point of the rising edge of the BCLK and the falling edge of BCLK# inputs in a differential implementation. See the P6 Family of Processors Hardware Developer's Manual for further details. The reference voltage of the BCLK in the P6 Family of Processors Hardware Developer Manual is re-defined as the crossing point of the BCLK and BCLK# in a differential implementation.
Figure 5. Differential/Single-Ended Clocking Example
BCLK + Clock Driver - BCLK# Processor or Chipset
Clock Driver
BCLK
Processor or Chipset
Clk E
Diff Si
l
2.6
Voltage Identification
There are five voltage identification (VID) pins on the PGA370 socket. These pins can be used to support automatic selection of VCCCORE voltages. The VID pins for the processor are open drain signals versus opens or shorts found on the previous Intel Celeron FC-PGA processor. Refer to Table 11 for level specifications for the VID signals. This pull-up resistor may be either external logic on the motherboard or internal to the Voltage Regulator. The VID signals rely on a 3.3 V pull-up resistor to set the signal to a logic high level. The VID pins are needed to fully support voltage specification variations on current and future processors. The voltage selection range for the processor is defined in Table 3. The VID25mV signal is a new signal that allows the voltage regulator or voltage regulator module (VRM) to output voltage levels in 25 mV increment necessary for the processor only. The current Celeron processor in the FCPGA package will not have this VID25mV signal. The VID25mV pin location is actually a Vss pin
Datasheet
19
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
on the model 68xh based on 0.18 micron process core processor. By connecting the VID25mV signal to the Vss pin, it will disable the 25 mV stepping granularity output and the regulator will resort to 50 mV stepping increment. The voltage regulator or VRM must supply the voltage that is requested or disable itself. In addition to the new signal "VID25mV", the processor will introduce a second new signal labeled as "VTT_PWRGD". The VTT_PWRGD signal informs the platform that the VID and BSEL signals are stable and should be sampled. During Power-up, the VID signals will be in an indeterminate state for a small period of time. The voltage regulator or the VRM should not latch the VID signals until the VTT_PWRGD signal is asserted by the VRM and sampled active. The assertion of the VTT_PWRGD signal indicates the VID signals are stable and are driven to the final state by the processor. Refer to Figure 14 for power-up timing sequence for the VTT_PWRGD and the VID signals. Table 3. Voltage Identification Definition 1
VID25mV 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 VID3 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 VID2 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 VID1 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 VID0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 VccCORE 1.05 1.075 1.10 1.125 1.15 1.175 1.20 1.225 1.25 1.275 1.30 1.325 1.35 1.375 1.40 1.425 1.45 1.475 1.50 1.525 1.55 1.575 1.60 1.625 1.65 1.675 1.70 1.725 1.75 1.775 1.80 1.825
NOTES: 1. 0 = Processor pin connected to VSS. and 1 = Open on processor; may be pulled up to TTL VIH (3.3 V max) on baseboard.
20
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
The VID pins should be pulled up to a 3.3 V level. This may be accomplished with pull-ups internal to the voltage regulator, which ensures valid VID pull-up voltage during Power-up and Power-down sequences. If external resistors are used for the VID[3:0, 25mV] signal, then the power source must be guaranteed to be stable whenever the supply to the voltage regulator is stable. This will prevent the possibility of the processor supply going above the specified VCCCORE in the event of a failure in the supply for the VID lines. In the case of a DC-to-DC converter, this can be accomplished by using the input voltage to the converter for the VID line pull-ups. A resistor equal to 1 k may be used to connect the VID signals to the voltage regulator input. Note: Intel requires that designs utilize VRM 8.5 and Not VRM 8.4 guidelines to meet the processor requirements. To re-emphasize, VRM 8.5 introduces two new signals [VID25mV and VTT_PWRGD] that is utilized by the processor and platform. Ignoring and not connecting these two new pins, as documented in the Platform Design Guidelines, will prevent the processor from operating at the specified voltage levels and core frequency. Figure 6 provides a high-level interconnection schematic. Refer to the VRM 8.5 DC-DC Converter Design Guideline and the appropriate Platform Design Guidelines for further detailed information on the voltage identification and bus select implementation. Refer to Figure 14 for VID power-up sequence and timing requirements. Figure 6. VTT Power Good and Bus Select Interconnect Diagram
VID[3:0, 25mV] VTT VRM 8.5 Voltage Regulator VTT VCCCORE 1 k VCCCORE
VTT Intel(R) Celeron Processor based on 0.13 Micron Process VTT_PWRGD (input) BSEL[1:0]
VTT_PWRGD (output)
Clock Driver
2.7
Processor System Bus Unused Pins
All RESERVED pins must remain unconnected unless specifically noted. Connection of these pins to VCCCORE, VREF, VSS, VTT or to any other signal (including each other) can result in component malfunction or incompatibility with future processors. See Section 5.4 for a pin listing of the processor and the location of each RESERVED pin. PICCLK must be driven with a valid clock input and the PICD[1:0] signals must be pulled-up to VCCCMOS1.5 even when the APIC will not be used. A separate pull-up resistor must be provided for each PICD signal. For reliable operation, always connect unused inputs or bidirectional signals to their deasserted signal level. The pull-up or pull-down resistor values are system dependent and should be chosen such that the logic high (VIH) and logic low (VIL) requirements are met. See Table 11 for level specifications of non-AGTL signals.
Datasheet
21
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
For unused AGTL inputs, the on-die termination will be sufficient. No external RTT is necessary on the motherboard For unused CMOS inputs, active low signals should be connected through a pull-up resistor to VCCCMOS1.5 and meet VIH requirements. Unused active high CMOS inputs should be connected through a pull-down resistor to ground (VSS) and meet VIL requirements. Unused CMOS outputs can be left unconnected. A resistor must be used when tying bidirectional signals to power or ground. When tying any signal to power or ground, a resistor will also allow for system testability.
2.8
Processor System Bus Signal Groups
To simplify the following discussion, the processor system bus signals have been combined into groups by buffer type. All P6 family processor system bus outputs are open drain and require a high-level source provided termination resistors. However, the processor includes on-die termination for AGTL signals and termination resistors placed on the platform are not necessary except for the RESET# signal which still requires external termination. AGTL input signals have differential input buffers which use VREF as a reference signal. AGTL output signals require termination to 1.25 V. In this document, the term "AGTL Input" refers to the AGTL input group as well as the AGTL I/O group when receiving. Similarly, "AGTL Output" refers to the AGTL output group as well as the AGTL I/O group when driving. The PWRGOOD signal input is a 1.8 V signal level and must be pulled up to VCCCMOS1.8. The VTT_PWRGD is not 1.8 V tolerant and must be connected to VTT (1.25 V). Other CMOS inputs (A20M#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, PREQ#, SMI, SLP#, and STPCLK#) are only 1.5 V tolerant and must be pulled up to VCCCMOS1.5. The CMOS, APIC, and TAP outputs are open drain and must be pulled to the appropriate level to meet the input specifications of the interfacing device. The groups and the signals contained within each group are shown in Table 4. Refer to Section 7.0 for a description of these signals.
22
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 4.
System Bus Signal Groups 1
Group Name AGTL Input AGTL Output AGTL I/O CMOS Input (1.25 V)3 CMOS Input (1.5 V)4 CMOS Input (1.8 V)5 CMOS Output (1.5 V)4 CMOS Output8 (3.3 V) System Bus Clock10 (1.25 V/2.5 V) APIC Clock9 APIC I/O
4
Signals BPRI#, DEFER#, RESET#, RSP# PRDY# A[35:3]#, ADS#, AERR#, AP[1:0]#, BERR#, BINIT#, BNR#, BP[3:2]#, BPM[1:0]#, BR0#2, D[63:0]#, DBSY#, DEP[7:0]#, DRDY#, HIT#, HITM#, LOCK#, REQ[4:0]#, RP#, RS[2:0]#, TRDY# VTT_PWRGD A20M#, FLUSH#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, PREQ#, SLP#, SMI#, STPCLK# PWRGOOD FERR#, IERR#, THERMTRIP# VID[3:0,25mV], BSEL[1:0]
BCLK0, BCLK0# PICCLK PICD[1:0] TCK, TDI, TMS, TRST#
TAP Input4 TAP Output
4
TDO CPUPRES#, DYN_OE, NCHTRL, PLL[2:1], SLEWCTRL, RTTCTRL7,THERMDN, THERMDP, VCCCORE, VREF, VSS, VTT, Reserved,
Power/Other6
NOTES: 1. See Section 7.0 for information on the these signals. 2. The BR0# pin is the only BREQ# signal that is bidirectional. See Section 7.0 for more information. 3. This signal is 1.25 V. 4. These signals are 1.5 V. 5. This signal is 1.8 V. 6. VCCCORE is the power supply for the processor core and is described in Section 2.6. VID[3:0,25mV] is described in Section 2.6. VTT is used to terminate the system bus and generate VREF on the motherboard. VSS is system ground. BSEL[1:0] is described in Section 2.8.2 and Section 7.0. All other signals are described in Section 7.0. 7. This signal is used to control the value of the processor on-die termination resistance. Refer to the platform design guide for the recommended pulldown resistor value. 8. These signals are 3.3 V. 9. These signals are 2.0 V. 10. 1.25 V signal for Differential clock application and 2.5 V for Single-ended clock application.
2.8.1
Asynchronous vs. Synchronous for System Bus Signals
All AGTL signals are synchronous to BCLK (BCLK/BCLK#). All of the CMOS, Clock, APIC, and TAP signals can be applied asynchronously to BCLK (BCLK/BCLK#). All APIC signals are synchronous to PICCLK. All TAP signals are synchronous to TCK.
Datasheet
23
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
2.8.2
System Bus Frequency Select Signals
The System Bus Frequency Select Signals (BSEL [1:0]) are used to select the system bus frequency for the processor. The BSEL signals are also used by the chipset and system bus clock generator. The BSEL pins for the processor are open drain signals versus opens or shorts found on the previous Intel Celeron FC-PGA processor. Refer to Table 11 for level specifications for the BSEL signals. The BSEL signals rely on a 3.3 V pull-up resistor to set the signal to a logic high level. Similar to the VID signals described in Section 2.6, the VTT_PWRGD signal also informs the platform that the BSEL signals are stable and should be sampled. During Power-up, the BSEL signals will be in a indeterminate state for a small period of time. The chipset or system bus clock generator should not sample and/or latch the BSEL signals until the VTT_PWRGD signal is asserted. The assertion of the VTT_PWRGD signal indicates the BSEL signals are stable and are driven to the final state by the processor. Refer to Figure 14 for power-up timing sequence for the VTT_PWRGD and the BSEL signals. Table 5 defines the possible combinations of the BSEL signals and the frequency associated with each combination. The frequency selection is determined by the processor(s) and driven out to the chipset and system bus clock generator. All system bus agents must operate at the same frequency determined by the processor. The processor operates at 100 MHz system bus frequency based on the system bus specified rating marked on the package. Over or under-clocking the system bus frequency outside the specified rating marked on the package is not recommended.
Figure 7. BSEL[1:0] Example for a System Design
3.3V 3.3V 1 k Processor BSEL0 BSEL1
Clock Driver
Chipset
Table 5.
Frequency Select Truth Table for BSEL[1:0]
BSEL1 0 0 1 1 BSEL0 0 1 0 1 Frequency Reserved 100 MHz Reserved Reseved
24
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
2.9
Test Access Port (TAP) Connection
Due to the voltage levels supported by other components in the Test Access Port (TAP) logic, it is recommended that the processor be first in the TAP chain and followed by any other components within the system. A translation buffer should be used to connect to the rest of the chain unless one of the other components is capable of accepting an input of the appropriate voltage. Similar considerations must be made for TCK, TMS, and TRST#. Two copies of each signal may be required with each driving a different voltage level.
2.10
Maximum Ratings
Table 6 contains processor stress ratings only. Functional operation at the absolute maximum and minimum is not implied nor guaranteed. The processor should not receive a clock while subjected to these conditions. Functional operating conditions are given in the timing and level tables in Section 2.11 through Section 2.13. Extended exposure to the maximum ratings may affect device reliability. Furthermore, although the processor contains protective circuitry to resist damage from static electric discharge, one should always take precautions to avoid high static voltages or electric fields.
Table 6.
Absolute Maximum Ratings
Symbol Parameter Min Max Unit Notes
TSTORAGE VCCCORE and VTT VinAGTL VinCMOS1.5 VVID & VBSEL
Processor storage temperature Processor core voltage and termination supply voltage with respect to VSS AGTL buffer input voltage CMOS buffer DC input voltage with respect to VSS Max VID and BSEL pin current
-40 0.5 -0.3 -0.3 -0.3
85 1.75 1.78 2.08 3.6
C V V V V 1, 3 2, 3, 4
NOTES: 1. Input voltage can never exceed VSS +1.78 volts. 2. Input voltage can never exceed VSS + 2.08 volts. 3. Input voltage can never go below -0.3 V 4. Parameter applies to CMOS, APIC, and TAP bus signal groups only.
2.11
Processor Voltage Level Specifications
The processor voltage level specifications in this section are defined at the PGA370 socket pins (bottom side of the motherboard). See Section 7.0 for the processor signal descriptions and Section 5.4 for the signal listings. Most of the signals on the processor system bus are in the AGTL signal group. These signals are specified to be terminated to 1.25 V. The voltage level specifications for these signals are listed in Table 10 on page 29. To allow connection with other devices, the clock, CMOS, APIC, and TAP signals are designed to interface at non-AGTL levels. The voltage level specifications for these pins are listed in Table 11 on page 29.
Datasheet
25
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 7 through Table 13 list the voltage level specifications for the processor. Specifications are valid only while meeting specifications for junction temperature, clock frequency, and input voltages. Care should be taken to read all notes associated with each parameter. Table 7. Voltage and Current Specifications (Sheet 1 of 2)
Symbol Parameter Core Freq Min Typ Max Unit Notes1, 2
1.4 GHz 1.30 GHz 1.20 GHz VCCCORE VCC for processor core 1.2014 GHz 1.10A GHz 1A GHz 900 MHz VTT VTT Vcc_cmos1.5 Vcc_cmos1.8 Baseboard VCCCORE Tolerance, Static Baseboard VCCCORE Tolerance, Transient Processor core voltage static tolerance level at the PGA370 socket pins Processor core voltage transient tolerance level at the PGA370 socket pins 1.4 GHz 1.30 GHz 1.20 GHz ICCCORE ICC for processor core 1.2014 GHz 1.10A GHz 1A GHz 900 MHz ICCCMOS1.5 ICCCMOS1.8 ICCCMOS3.3 IVTT ISGnt ICC for VccCMOS1.5 ICC for VccCMOS1.8 ICC for VccCMOS3.3 Termination voltage supply current ICC Stop-Grant for processor core 1.4 GHz 1.30 GHz 1.20 GHz IDSLP ICC Deep Sleep 1.2014 GHz 1.1A GHz 1A GHz 900 MHz dICCCORE/dt Power supply current slew rate Static AGTL bus termination voltage Transient AGTL bus termination voltage
1.5 1.5 1.5 1.475 1.475 1.475 1.475 1.25 1.25 1.5 1.8 V V V V 1.25 3%, 4 1.25 9%, 4 1.5 10%, 12 1.8 10%, 12 V 3, 13
V Refer to Figure 8 and Table 9 for Tolerance values V
5
5
22.6 22.5 21.5 20.6 19.9 19.1 18.1 250 1 35 2.3 15.37 12.0 12.0 12.0 11.0 11.0 11.0 11.0 Refer to Table 8 for Slew Rate A/s 8, 9, 10, 11 A mA mA mA A A 7, 8 A 6, 13
26
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 7.
Voltage and Current Specifications (Sheet 2 of 2)
Symbol Parameter Core Freq Min Typ Max Unit Notes1, 2
dIvTT/dt
Termination current slew rate
Table 13
A/s
8, 9, 10 See Table 13
NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. All specifications in this table apply only to the Celeron processor based on 0.13 micron process core. 3. VccCORE and IccCORE supply the processor core and the on-die L2 cache. 4. VTT must be held to 1.25 V 9% while the AGTL bus is active. It is required that VTT be held to 1.25 V 3% while the processor system bus is static (idle condition). The 3% range is the required design target; 9% will come from the transient noise added. This is measured at the PGA370 socket pins on the bottom side of the baseboard. 5. These are the tolerance requirements, across a 20 MHz frequency bandwidth, measured at the processor socket pin on the soldered-side of the motherboard. VCCCORE must return to within the static voltage specification within 100 s after a transient event; see the VRM 8.5 DC-DC Converter Design Guidelines for further details. 6. Maximum ICC is measured at VCC typical voltage and under a maximum signal loading conditions. 7. The current specified is also for AutoHALT state. 8. Maximum values are specified by design/characterization at nominal VccCORE. 9. Based on simulation and averaged over the duration of any change in current. Use to compute the maximum inductance tolerable and reaction time of the voltage regulator. This parameter is not tested. 10. dIcc/dt specifications are measured and specified at the PGA370 socket pins. 11. Static voltage regulation includes: DC output initial voltage set point adjust, Output ripple and noise, Output load ranges specified in the tables above. See VRM 8.5 Specification. 12.Pull ups only. 13. For frequencies beyond 1.40 GHz, refer to the latest flexible motherboard 1 extended (FMB1-E) guidelines available via your Intel Representative. 14. 1.20 GHz at VccCORE = 1.475 volts and S-Spec number SL5XS.
Table 8.
Power Supply Current Slew Rate (dIcccore/dt)
Slew Rate: 26 A Load Step Slew Rate (26 A): ICC at Socket 30 25 ICC @ socket (A) 20 15 10 5 0 0 1 2 3 4 5 6 PWL SLew Rate Data Time (us) 0.1 0.15 0.5 1 1.5 2 2.5 4 3.5 4 4.5 ICC at Socket (A) 26.23 23.18 20.03 21.10 21.88 22.29 22.30 22.07 21.78 21.58 21.51
Table 8 contains typical slew rate data for the processor. Actual slew rate values and wave-shapes may vary slightly depending on the type and size of decoupling capacitors used in a particular implementation.
Datasheet
27
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 9.
Vcc Static & Transient Tolerance
Voltage Deviation from VID Setting (mV) Static Tolerance Icc (A) Min Max Transient Tolerance Min Max
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
15 5 -5 -15 -25 -35 -45 -55 -65 -75 -85 -95 -105 -115 -125 -135
65 55 45 35 25 15 5 -5 -15 -25 -35 -45 -55 -65 -75 -85
5 -5 -15 -25 -35 -45 -55 -65 -76 -87 -98 -110 -121 -132 -144 -155
85 74 62 51 40 28 17 6 -5 -15 -25 -35 -45 -55 -65 -75
Figure 8. Vcc Static and Transient Tolerance
80 Vcc Droop from VID setting (mV) 60 40 20 0 -2 0 -4 0 -6 0 -8 0 -1 0 0 -1 2 0 -1 4 0 0
S tatic M in im u m L o a d L in e T ran s ie n t M in im u m L o a d L in e Tran s ien t M a xim u m L o a d L in e S ta tic M ax im u m L o ad L in e
5
10
15 Ic c L o a d (A )
20
25
30
28
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 10. AGTL Signal Group Levels Specifications
Symbol Parameter Min Max Unit Notes1
VIL VIH Ron IL
Input Low Voltage Input High Voltage Buffer On Resistance Leakage Current for inputs, outputs, and I/O VREF + 0.200
VREF - 0.200 16.67 100
V V
6 2, 3, 6 5 4, 7
A
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor at a frequency up to 1.40 GHz on 0.13 micron. 2. All inputs, outputs, and I/O pins must comply with the signal quality specifications in Section 3.0. 3. Minimum and maximum VTT are given in Table 13 on page 30. 4. (0 VIN 1.25 V +3%) and (0VOUT1.25 V+3%). 5. Refer to the processor I/O Buffer Models for I/V characteristics. 6. Steady state input voltage must not be above VSS + 1.65 V or below VTT - 1.65 V. 7. Does not apply to Vcc leakage current due to the presence of on-die RTT.
Table 11. Non-AGTL Signal Group Levels Specifications
Symbol Parameter Min Max Unit Notes1
VIL1.2 VIL1.5 VIL1.8 VIL2.0 VIH1.2 VIH1.5 VIH1.5PICD VIH1.8 VIH2.0 Ron VOL IOL ILI ILO
Input Low Voltage Input Low Voltage Input Low Voltage Input Low Voltage Input High Voltage Input High Voltage Input High Voltage PICD[1:0] Input High Voltage Input High Voltage -0.150 -0.36 -0.40 1.03 Vcmos_ref + 0.250 Vcmos_ref + 0.200 1.44 1.60
0.4 Vcmos_ref - 0.300 0.36 0.40
V V V V V
11 10 8 9 11 6, 10, 12 12, 13 8 9 2 7, 9, All outputs are open-drain
VCC_CMOS1.5 + 10% 2.0 2.16
V V V V
30 Output Low Voltage Output Low Current Input Leakage Current Output Leakage Current 0.30 10 100 100
V mA A A
3, 6 3, 4, 6, 7
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency on 0.13 micron. 2. Parameter measured at 9 mA (for use with TTL inputs). 3. (0 VIN 1.8 V +10%). 4. (0 VOUT 1.8 V +10%). 5. For BCLK specifications, refer to Table 24 on page 41. 6. (0 VIN 1.5 V +10%). 7. (0 VOUT 1.5 V +10%). 8. Applies to non-AGTL signal PWRGOOD. 9. Applies to non-AGTL signal PICCLK. 10.Applies to non-AGTL signals except BCLK, PICCLK, and PWRGOOD. 11.Applies to non-AGTL signal VTT_PWRGD. 12.Vcmos_ref = 2/3 Vcc_cmos1.5, refer to Table 7 on page 26. 13.Applies to PICD[1:0] only
Datasheet
29
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 12. 3.3 Volt CMOS Output Signal Group DC Specifications
Symbol Parameter Min Max Unit Notes
V VOH ILO
Nominal Voltage Output High Voltage Output Leakage Current
3.45 0.9 100
V V A
3.3 + 5%
2.12
AGTL System Bus Specifications
It is recommended that the AGTL bus be routed in a daisy-chain fashion with termination resistors to VTT. These termination resistors are placed electrically between the ends of the signal traces and the VTT voltage supply. The valid high and low levels are determined by the input buffers using a reference voltage called VREF. Refer to the appropriate platform design guide for more information Table 13 lists the nominal specification for the AGTL termination voltage (VTT). The AGTL reference voltage (VREF) is generated on the system motherboard and should be set to 2/3 VTT for the processor and other AGTL logic. It is important that the baseboard impedance be specified and held to a 15% tolerance, and that the intrinsic trace capacitance for the AGTL signal group traces is known and well-controlled. For more details on the AGTL buffer specification, see the Intel(R) Pentium(R) II Processor Developer's Manual and AP-585, Intel(R) Pentium(R) II Processor AGTL Guidelines.
Table 13. Processor AGTL Bus Specifications
Symbol Parameter Min Typ Max Units Notes 1,2
VTT On-die RTT VREF
Bus Termination Voltage Termination Resistor Bus Reference Voltage
1.1375 50
1.25 56 68 2/3VTT 115
V
3 4 5
V
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency. 2. The processor for the PGA370 socket contain AGTL termination resistors on the processor die, except for the RESET# input. 3. VTT must be held to 1.25 V 9%. It is required that VTT be held to 1.25 V 3% while the processor system bus is idle (static condition). This is measured at the PGA370 socket pins on the bottom side of the baseboard. 4. Uni-processor platforms require a 56 resistor and dual-processor platforms require a 68 resistor. Tolerance for on-die Rtt is 10% (56 , 68 resistors). Rtt is 15% (100 resistors). 5. VREF is generated on the motherboard and should be 2/3 VTT 5% nominally. Insure that there is adequate VREF decoupling on the motherboard.
30
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
2.13
System Bus Timing Specifications
The processor system bus timings specified in this section are defined at the socket pins on the bottom of the motherboard. Unless otherwise specified, timings are tested at the processor pins during manufacturing. Timings at the processor pins are specified by design characterization. See Section 7.0 for the processor signal definitions. Table 14 through Table 21 list the timing specifications associated with the processor system bus. These specifications are broken into the following categories: Table 14 contains the system bus clock specifications for Single-ended clock mode operation and Table 15 contains the system bus clock specifications for Differential clock mode operation. Table 17 contains the AGTL specifications, Table 18 contains the CMOS signal group specifications, Table 19 contains timings for the reset conditions, Table 20 and covers APIC bus timing, and Table 21 covers TAP timing. All processor system bus timing specifications for the AGTL signal group are relative to the rising edge of the BCLK input. All AGTL timings are referenced to VREF for both `0' and `1' logic levels unless otherwise specified.. AGTL layout guidelines are also available in the appropriate platform design guide. Care should be taken to read all notes associated with a particular timing parameter.
7
Table 14. System Bus Timing Specifications (Single-Ended Clock)
100 MHz T# Parameter Min Max Unit Figure Notes 1,4
T1: BCLK Period - average T1abs: BCLK Period - Instantaneous minimum T2: BCLK Period Stability T5: BCLK Rise Time T6: BCLK Fall Time T3: BCLK High Time T4: BCLK Low Time T7: BCLK Input High T8: BCLK Input Low
10.0 9.75
10.15
nS nS
9
2 2 2
250 0.4 0.4 2.5 2.4 2.2 0.3 1.6 1.6
pS nS nS nS nS V V 10 10 10 10
3 3 5 6
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency on 0.13 micron process. 2. Period, jitter, offset and skew measured at 1.25 V. 3. Measured from 0.5 to 2.0 V. 4. CLKREF (BCLK#) = 1.25 V with 5% DC tolerance. CLKREF must be generated from a stable source. AC tolerances must be less than -40 dB at 1 MHz. 5. BCLK High Time is measured above 2.0 V. 6. BCLK Low Time is measured below 0.5 V.
Datasheet
31
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 15. System Bus Timing Specifications (Differential Clock)
100 MHz T# Parameter Min Max Unit Figure Notes 1,2,6
T1: BCLK Period - average T1abs: BCLK Period - Instantaneous minimum T2: BCLK Period Stability Vcross: Crossing point at 1V Swing T5: BCLK Rise Time T6: BCLK Fall Time Rise/Fall Time Matching BCLK Duty Cycle Input High Voltage Input Low Voltage Rising Edge Ring Back Falling Edge Ring Back
10.0 9.8
10.2
nS nS
9
3, 4 3, 4 5
200 0.51 175 175 0.76 550 550 325 45% 0.92 -0.2 0.35 -0.35 55% 1.45 0.35
pS V pS pS pS 9 10 10
7, 8 7, 8
4 V V V V
1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency on 0.13 micron process. 2. All timings for the AGTL signals are referenced at the rising edge of BCLK and the falling edge of BCLK# at the processor pin. All AGTL signal timings (address bus, data bus, etc.) are referenced at 1.00 V at the processor pins. 3. The internal core clock frequency is derived from the processor system bus clock. The system bus clock to core clock ratio is determined during initialization. Individual processors will only operate at their specified system bus frequency, 100 MHz. Table 16 shows the supported ratios for each processor. 4. Due to the difficulty of accurately measuring clock jitter in a system, it is recommended that a clock driver be used that is designed to meet the period stability specification into a test load of 10 to 20 pF. This should be measured at adjacent crossing points of BCLK and BCLK# which is defined as the rising edge of BCLK and the falling edge of BCLK# at the processor pin. The jitter present must be accounted for as a component of BCLK timing skew between devices. 5. The clock driver's closed loop jitter bandwidth must be set low to allow any PLL-based device to track the jitter created by the clock driver. The -20 dB attenuation point, as measured into a 10 to 20 pF load, should be less than 500 kHz. This specification may be ensured by design characterization and/or measured with a spectrum analyzer. See the appropriate clock synthesizer/driver specification for details 6. Measurement taken from differential waveform, defined as BCLK - BCLK#. 7. Rise time is measured from -0.35 to +0.35V and fall time is measured from 0.35 V to -0.35 V. 8. Measured at the socket pin.
32
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 16. Valid System Bus to Core Frequency Ratios 1, 2, 3
Processor Core Frequency BCLK Frequency (MHz) Frequency Multiplier
1.4 GHz 1.30 1.20 1.204 1.1A 1A 900
1.40 1.30 GHz 1.20 GHz 1.204 GHz
100 100 100 100 100 100 100
14 13 12 12 11 10 9
1.1A GHz 1A GHz 900 MHz
NOTES: 1. Contact your local Intel representative for the latest information on processor frequencies and/or frequency multipliers. 2. While other bus ratios are defined, operation at frequencies other than those listed are not supported by the processor. 3. Individual processors will only operate at their specified system bus frequency; 100 MHz. 4. 1.20 GHz at VccCORE = 1.475 volts and S-Spec number SL5XS.
Table 17. System Bus Timing Specifications (AGTL Signal Group)
T# Parameter Min Max Unit Figure Notes 1,2,3
T7: AGTL Output Valid Delay T8: AGTL Input Setup Time T9: AGTL Input Hold Time T10: RESET# Pulse Width
0.40 1.30 1.00 1.00
3.25
ns ns ns ms
11 12 12 13
4 5, 6, 7, 10 8 6, 9
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz on 0.13 micron process. 2. These specifications are tested during manufacturing. 3. All timings for the AGTL signals are referenced to the rising edge of BCLK and the falling edge of BCLK# at the processor pin. All AGTL signal timings (compatibility signals, etc.) are referenced at 0.80 V at the processor pins. 4. Valid delay timings for these signals are specified into 50 to 1.25 V, VREF at 0.8 V 2% and with 56 or 68 on-die RTT. 5. A minimum of 3 clocks must be guaranteed between two active-to-inactive transitions of TRDY#. 6. RESET# can be asserted (active) asynchronously, but must be deasserted synchronously. 7. Specification is for a minimum 0.40 V swing from VREF - 200 mV to VREF + 200 mV. This assumes an edge rate of 0.3V/ns. 8. Specification is for a maximum 0.8 V swing from VTT - 0.8V to VTT. This assumes an edge rate of 3 V/ns. 9. This should be measured after VCCCORE, VTT, VccCMOS, and BCLK (and BCLK#) are stable 10.BREQ signals observe a 1.2 ns minimum setup time.
Table 18. System Bus Timing Specifications (CMOS Signal Group)
T# Parameter Min Max Unit Figure Notes 1,2,3,4
T14: CMOS Input Pulse Width, except PWRGOOD T15: PWRGOOD Inactive Pulse Width
2 10
BCLKs BCLKs
11 15
Active and Inactive states 5
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency 2. These specifications are tested during manufacturing. 3. These signals may be driven asynchronously.
Datasheet
33
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
4. All CMOS outputs shall be asserted for at least 2 system bus clocks. 5. When driven inactive or after VCCCORE, VTT, VCCCMOS, and BCLK and BCLK# are stable.
Table 19. System Bus Timing Specifications (Reset Conditions) 1
T# Parameter Min Max Unit Figure Notes
T16: Reset Configuration Signals (A[14:5]#, BR0#, INIT#) Setup Time T17: Reset Configuration Signals (A[14:5]#, BR0#, INIT#) Hold Time
4 2 20
BCLKs BCLKs
13 13
Before deassertion of RESET# After clock that deasserts RESET#
NOTE: 1. Unless otherwise noted, all specifications in this table apply to all the processor up to 1.40 GHz frequency.
Table 20. System Bus Timing Specifications (APIC Clock and APIC I/O)1, 2, 3
T# Parameter Min Max Unit Figure Notes
T21: PICCLK Frequency T22: PICCLK Period T23: PICCLK High Time T24: PICCLK Low Time T25: PICCLK Rise Time T26: PICCLK Fall Time T27: PICD[1:0] Setup Time T28: PICD[1:0] Hold Time T29a: PICD[1:0] Valid Delay (Rising Edge) T29b: PICD[1:0] Valid Delay (Falling Edge)
2.0 30.0 10.5 10.5 0.25 0.25 8.0 2.5 1.5 1.5
33.3 500.0
MHz ns ns ns 10 10 10 10 10 12 12 11 10 @ > 1.60 V @ < 0.40 V (0.40 V - 1.60 V) (1.60 - 0.40 V) 4 4 4, 5, 6 4, 5, 6
3.0 3.0
ns ns ns ns
8.7 12.0
ns ns
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency. 2. These specifications are tested during manufacturing. 3. All timings for the APIC I/O signals are referenced to the PICCLK rising edge at 0.9 V at the processor pins. All APIC I/O signal timings are referenced at 1.0 V at the processor pins. 4. Referenced to PICCLK rising edge. 5. For open drain signals, valid delay is synonymous with float delay. 6. Valid delay timings for these signals are specified into 150 load pulled up to 1.5 V.
34
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 21. System Bus Timing Specifications (TAP Connection)
T# Parameter Min Max Unit Figure Notes 1,2,3
T30: TCK Frequency T31: TCK Period T32: TCK High Time T33: TCK Low Time T34: TCK Rise Time 60.0 25.0 25.0
16.667
MHz ns ns ns 10 10 10 10 Vcmos_ref + 0.200 V, 10 Vcmos_ref - 0.200 V, 10 (Vcmos_ref - 0.200 V) - (Vcmos_ref + 0.200 V), 4, 10 (Vcmos_ref + 0.200 V) - (Vcmos_ref - 0.200 V), 4, 10 Asynchronous, 10 5 5 6, 7 6, 7, 10 6, 8, 9 6, 8, 9, 10 5, 8, 9 5, 8, 9
5.0
ns
T35: TCK Fall Time T36: TRST# Pulse Width T37: TDI, TMS Setup Time T38: TDI, TMS Hold Time T39: TDO Valid Delay T40: TDO Float Delay T41: All Non-Test Outputs Valid Delay T42: All Non-Test Inputs Setup Time T43: All Non-Test Inputs Setup Time T44: All Non-Test Inputs Hold Time 5.0 13.0 2.0 40.0 5.0 14.0 1.0
5.0
ns ns ns ns
10 17 16 16 16 16 16 16 16 16
10.0 25.0 25.0 25.0
ns ns ns ns ns ns
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency. 2. All timings for the TAP signals are referenced to the TCK rising edge at 1.0 V at the processor pins. All TAP signal timings (TMS, TDI, etc.) are referenced at 1.0 V at the processor pins. 3. These specifications are tested during manufacturing, unless otherwise noted. 4. 1 ns can be added to the maximum TCK rise and fall times for every 1 MHz below 16.667 MHz. 5. Referenced to TCK rising edge. 6. Referenced to TCK falling edge. 7. Valid delay timing for this signal is specified to 1.5 V. 8. Non-Test Outputs and Inputs are the normal output or input signals (besides TCK, TRST#, TDI, TDO, and TMS). These timings correspond to the response of these signals due to TAP operations. 9. During Debug Port operation, use the normal specified timings rather than the TAP signal timings. 10.Not 100% tested. Specified by design characterization.
Datasheet
35
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 22. Platform Power-On Timings
T# Parameter Min Max Unit Figure Notes 2
T45: Valid Time Before VTT_PWRGD T46: Valid Time Before PWRGOOD T47: RESET# Inactive to Valid Outputs T48: RESET# Inactive to Drive Signals
1.0 2.0 1 4
mS mS BCLK BCLK
14 14 14 14
1 1 1 1
NOTES: 1. All signals, during their invalid states, must be guarded against spurious levels from effecting the platform during processor power-up sequence. 2. Configuration Input signals include: A[14:5], BR0#, INIT#. For timing of these signals, refer to Table 18 and Figure 13.
Notes: For Figure 9 through Figure 19, the following apply: 1. Figure 9 through Figure 19 are to be used in conjunction with Table 14 through Table 21. 2. All timings for the AGTL signals at the processor pins are referenced to the rising edge of BCLK and the falling edge of BCLK# at the crossing point for differential clock mode and to the rising edge of BCLK at BCLKVREF (1.25 V) for single-ended clock mode. All AGTL signal timings (address bus, data bus, etc.) are referenced at 2/3VTT at the processor pins. 3. All timings for the APIC I/O signals at the processor pins are referenced to the PICCLK rising edge at 0.9 V. All APIC I/O signal timings are referenced at 1.0 V at the processor pins. 4. All timings for the TAP signals at the processor pins are referenced to the TCK rising edge at 1.0 V. All TAP signal timings (TMS, TDI, etc.) are referenced at 1.0 V at the processor pins. Figure 9. Clock Waveform
BC LK
V ih
V c ro s s
BCLK# V il Tp
T p = T 1 ( B C L K P e r io d ) N O T E : S in g le - E n d e d c lo c k u s e s B C L K o n ly , D if f e r e n tia l c lo c k u s e s B L C K a n d B C L K #
36
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 10. BCLK/BCLK#, PICCLK, and TCK Generic Clock Waveform
Tp Th
Vringback (rise) 0V Vringback (fall)
Vih diff
V2 V3 V1
Vil diff
Tr Tf Th Tl Tp V1
T5, T25, T34, (Rise Tim e) Tf Tl Tr T6, T26, T35, (Fall Tim e) T3, T23, T32, (High Tim e) T4, T24, T33, (Low Tim e) T1, T22, T31 (BC LK, TCK, PIC CLK Period) B CLK is referenced to 0.30V (D ifferential M ode), 0.50V (Single-Ended M ode) TCK is referenced to Vref - 200 m V, PICC LK is referenced to 0.4V. V2 = B CLK is refernced to 0.9V (Differental M ode), 2.0V (Single-E nded M ode) TCK is referenced to Vref + 200 m V, PICC LK is refernced to 1.6V V3 = B CLK and BLCK # crossing point of the rising edge of BLCK and the falling edge of BCLK# (Differential M ode), BCLK i refereced to 1.25V (Single-Ended M ode), PIC CLK is reference to 1.0V, TCK is referenced to Vcm osref
= = = = = =
Figure 11. System Bus Valid Delay Timings
BCLK# BCLK Tx V Valid Tpw
Tx = T7, T29a, T29b (Valid Delay) Tpw = T14, T15 (Pulse Width) NOTE: Single-Ended clock uses BCLK only, Differential clock uses BCLK and BCLK#
Tx
Signal
Valid
V = Vref for AGTL signal group; Vcmosref for CMOS, APIC and TAP signal groups
Datasheet
37
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 12. System Bus Setup and Hold Timings
BCLK# VCross BCLK Ts V Th Valid
VCross = Crossing point of BLCK and BCLK# Ts = T8, T27 (Setup Time) NOTE: Single-Ended clock uses BCLK only, Differential clock uses BCLK and BCLK# Th = T9, T28 (Hold Time) V = Vref for AGTL signal group; 0.75V for APIC and TAP signal groups
Figure 13. System Bus Reset and Configuration Timings
BCLK# BCLK
T8 T9
RESET#
T10
T17
Configuration (A[14:5]#, BR0#, FLUSH#, INT#)
T16 Valid
T9 = (AGTL+ Input Hold Time) NOTE: Single-Ended clock uses BCLK only, T8 = (AGTL+ Input Setup Time) Differential clock uses BCLK and BCLK# T10 = (RESET# Pulse Width) T16 = (Reset Configuration Signals (A[14:5]#, BR0#, FLUSH#, INIT#) Setup Time) T17 = (Reset Configuration Signals (A[14:5]#, BR0#, FLUSH#, INIT#) Hold Time)
38
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 14. Platform Power-On Sequence and Timings
Vtt, Vref Vcmosref VID BSEL[1:0]
T45 Valid
Valid
VTT_PWRGD VCC_Core BCLK# BCLK PICCLK VCC_PWRGD Configuration Inputs RESET# THERMTRIP# PICD[1:0] AGTL Outputs All other CMOS Outputs All other Inputs
Inactive Inactive T46
Valid Config
Active
T47 Valid
Valid
Valid
Valid
Active T48
Figure 15. Power-On Reset and Configuration Timings
BCLK VccCORE, VTT, VREF
PWRGOOD Ta RESET#
VIL, max
VIH, min Tb
TC Configuration (A20M#, IGNNE#, INTR, NMI) Ta Tb Tc Valid Ratio = T15 (PWRGOOD Inactive Pulse) = T10 (RESET# Pulse Width) = T20 (Reset Configuration Signals (A20M#, IGNNE#, LINT[1:0]) Hold Time)
Datasheet
39
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 16. Test Timings (TAP Connection)
TCK Tv TDI, TMS Tr Input Signal Tx TDO Ty Output Signal Tz Tu Ts Tw
Tr = T43 (All Non-Test Inputs Setup Time) Ts = T44 (All Non-Test Inputs Hold Time) Tu = T40 (TDO Float Delay) Tv = T37 (TDI, TMS Setup Time) Tw = T38 (TDI, TMS Hold TIme) Tx = T39 (TDO Valid Delay) Ty = T41 (All Non-Test Outputs Valid Delay) Tz = T42 (All Non-Test Outputs Float Time)
Figure 17. Test Reset Timings
TRST#
1.00V
T36 T36 = TRST# Pulse Width
40
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
3.0
Signal Quality Specifications
Signals driven on the processor system bus should meet signal quality specifications to ensure that the components read data properly and to ensure that incoming signals do not affect the long term reliability of the component. Specifications are provided for simulation at the processor pins. Meeting the specifications at the processor pins in Table 23, Table 24, and Table 27 ensures that signal quality effects will not adversely affect processor operation.
3.1
BCLK/BCLK# & PICCLK Signal Quality Specifications and Measurement Guidelines
Table 24 describes the signal quality specifications at the processor pins for the processor system bus clock (BCLK/BCLK#) and APIC clock (PICCLK) signals. References made to BCLK signal quality specifications also applies to BCLK#. Figure 18 describes the signal quality waveform for the system bus clock at the processor pins.
Table 23. BCLK (Single-Ended Clock Mode) Signal Quality Specifications for Simulation at the Processor Pins
T# Parameter Min Nom Max Unit Figure Notes 1
V1: BCLK VIL V2: BCLK VIH V3: BCLK Absolute Voltage Range V4: BCLK Rising Edge Ringback V5: BCLK Falling Edge Ringback 2.2 -0.5 2.0
0.3
V V
18 18 18 18 18 2 2
3.1
V V
0.5
V
Table 24. BCLK/BCLK# (Differential Clock Mode) and PICCLK Signal Quality Specifications for Simulation at the Processor Pins
T# Parameter Min Nom Max Unit Figure Notes 1
V1: BCLK VIL V1: PICCLK VIL V2: BCLK VIH V2 PICCLK VIH V3: BCLK Absolute Voltage Range V3: PICCLK Absolute Voltage Range V4: BCLK Rising Edge Ringback V4: PICCLK Rising Edge Ringback V5: BCLK Falling Edge Ringback V5: PICCLK Falling Edge Ringback
-0.2
0.35 0.40
V V V V
18 18 18 18 18 18 18 18 18 18 2 2 2 2
0.92 1.60 -0.2 -0.4 0.35 1.60
1.45
1.45 2.4
V V V V
-0.35 0.40
V V
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency. 2. The rising and falling edge ringback voltage specified is the minimum (rising) or maximum (falling) absolute voltage the BCLK/BCLK# and PICCLK signals can dip back to after passing the VIH (rising) or VIL (falling) voltage limits. This specification is an absolute value.
Datasheet
41
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 18. BCLK/BCLK#, PICCLK Generic Clock Waveform at the Processor Pins
V3
V4
V2
V1
V5
V3
3.2
AGTL Signal Quality Specifications and Measurement Guidelines
Many scenarios have been simulated to generate a set of AGTL layout guidelines which are available in the appropriate platform design guide. Refer to the Intel(R) Pentium(R) II Processor Developer's Manual (Order Number 243502) for the AGTL buffer specification. Table 25 provides the AGTL signal quality specifications for the processor for use in simulating signal quality at the processor pins. The processor maximum allowable overshoot and undershoot specifications for a given duration of time are detailed in Table 24 through Table 26. Figure 19 shows the AGTL ringback tolerance and Figure 20 shows the overshoot/undershoot waveform.
Table 25. AGTL Signal Groups Ringback Tolerance Specifications at the Processor Pins
T# Parameter : Overshoot : Minimum Time at High : Amplitude of Ringback : Final Settling Voltage : Duration of Squarewave Ringback Min Unit Figure Notes 1,2,3
100 0.50 200 200 N/A
mV ns mV mV ns
19 19 19 19 19
4, 8
5, 6, 7, 8 8
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency. 2. Specifications are for the edge rate of 0.3 - 3 V/ns. See Figure 19 for the generic waveform. 3. All values specified by design characterization. 4. See Table 24 for maximum allowable overshoot. 5. Ringback between VREF + 100 mV and VREF + 200 mV or VREF - 300 mV and VREF - 100 mVs requires the flight time measurements to be adjusted as described in the Intel AGTL Specifications. Ringback below VREF + 100 mV or above VREF - 100 mV is not supported. 6. Intel recommends simulations not exceed a ringback value of VREF 200 mV to allow margin for other sources of system noise. 7. A negative value for indicates that the amplitude of ringback is above VREF. (i.e., = -100 mV specifies the signal cannot ringback below VREF + 100 mV). 8. and : are measured relative to VREF. : is measured relative to VREF + 200 mV.
42
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 19. Low to High AGTL Receiver Ringback Tolerance
Vstart Clock
VREF + 0.2 VREF VREF - 0.2
0.7V Clk Ref
Time Note: High to low case is analogous
i b k tl
3.2.1
Overshoot/Undershoot Guidelines
Overshoot (or undershoot) is the absolute value of the maximum voltage above the nominal high voltage or below VSS. The overshoot guideline limits transitions beyond VCC or VSS due to the fast signal edge rates. The processor can be damaged by repeated overshoot events on 1.25 V or 2.5 V tolerant buffers if the charge is large enough (i.e., if the overshoot is great enough). Determining the impact of an overshoot/undershoot condition requires knowledge of the magnitude, the pulse direction and the activity factor (AF). Permanent damage to the processor is the likely result of excessive overshoot/undershoot. Violating the overshoot/undershoot guideline will also make satisfying the ringback specification difficult. When performing simulations to determine impact of overshoot and undershoot, ESD diodes must be properly characterized. ESD protection diodes do not act as voltage clamps and will not provide overshoot or undershoot protection. ESD diodes modeled within Intel I/O Buffer models do not clamp undershoot or overshoot and will yield correct simulation results. If other I/O buffer models are being used to characterize the processor performance, care must be taken to ensure that ESD models do not clamp extreme voltage levels. Intel I/O Buffer models also contain I/O capacitance characterization. Therefore, removing the ESD diodes from an I/O Buffer model will impact results and may yield excessive overshoot/undershoot.
Datasheet
43
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
3.2.2
Overshoot/Undershoot Magnitude
Magnitude describes the maximum potential difference between a signal and its voltage reference level, VSS (overshoot) and VTT (undershoot). While overshoot can be measured relative to VSS using one probe (probe to signal and GND lead to VSS), undershoot must be measured relative to VTT. This could be accomplished by simultaneously measuring the VTT plane while measuring the signal undershoot. Today's oscilloscopes can easily calculate the true undershoot waveform. The true undershoot waveform can also be obtained with the following oscilloscope data file analysis: Converted Undershoot Waveform = VTT - Signal_measured Note: Note: The converted undershoot waveform appears as a positive (overshoot) signal. Overshoot (rising edge) and undershoot (falling edge) conditions are separate and their impact must be determined independently. After the true waveform conversion, the undershoot/overshoot specifications shown in Table 26 through Table 29 can be applied to the converted undershoot waveform using the same magnitude and pulse duration specifications used with an overshoot waveform. Overshoot/undershoot magnitude levels must observe the Absolute Maximum Specifications listed in Table 26 through Table 29. These specifications must not be violated at any time regardless of bus activity or system state. Within these specifications are threshold levels that define different allowed pulse durations. Provided that the magnitude of the overshoot/undershoot is within the Absolute Maximum Specifications (1.78 V AGTL, 2.08 V CMOS), the pulse magnitude, duration and activity factor must all be used to determine if the overshoot/undershoot pulse is within specifications.
3.2.3
Overshoot/Undershoot Pulse Duration
Pulse duration describes the total time an overshoot/undershoot event exceeds the overshoot/ undershoot reference voltage (Vos_ref = 1.32 V AGTL, 1.80 V CMOS). The total time could encompass several oscillations above the reference voltage. Multiple overshoot/undershoot pulses within a single overshoot/undershoot event may need to be measured to determine the total pulse duration. Note: Note: Oscillations below the reference voltage can not be subtracted from the total overshoot/undershoot pulse duration. Multiple Overshoot/Undershoot events occurring within the same clock cycle must be considered together as one event. Using the worst case Overshoot/Undershoot Magnitude, sum together the individual Pulse Durations to determine the total Overshoot/Undershoot Pulse Duration for that total event.
3.2.4
Activity Factor
Activity Factor (AF) describes the frequency of overshoot (or undershoot) occurrence relative to a clock. Since the highest frequency of assertion of an AGTL or a CMOS signal is every other clock, an AF = 1 indicates that the specific overshoot (or undershoot) waveform occurs EVERY OTHER clock cycle. Thus, an AF = 0.01 indicates that the specific overshoot (or undershoot) waveform occurs one time in every 200 clock cycles. The specifications provided in Table 26 through Table 29 show the Maximum Pulse Duration allowed for a given Overshoot/Undershoot Magnitude at a specific Activity Factor. Each Table entry is independent of all others, meaning that the Pulse Duration reflects the existence of overshoot/undershoot events of that magnitude ONLY. A platform with an overshoot/undershoot
44
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
that just meets the pulse duration for a specific magnitude where the AF < 1, means that there can be NO other overshoot/undershoot events, even of lesser magnitude (note that if AF = 1, then the event occurs at all times and no other events can occur). Note: Note: Activity factor for AGTL signals is referenced to system bus clock frequency. Activity factor for CMOS signals is referenced to PICCLK frequency.
3.2.5
Reading Overshoot/Undershoot Specification Tables
The overshoot/undershoot specification for the processor is not a simple single value. Instead, many factors are needed to determine what the over/undershoot specification is. In addition to the magnitude of the overshoot, the following parameters must also be known: the junction temperature the processor will be operating at, the width of the overshoot (as measured above TBD V) and the Activity Factor (AF). To determine the allowed overshoot for a particular overshoot event, the following must be done: 1. Determine the signal group that particular signal falls into. If the signal is an AGTL signal operating with a 100 MHz system bus, use Table 27 (100 MHz AGTL signal group). If the signal is a CMOS signal, use Table 28 (33 MHz CMOS signal group). 2. Determine the maximum case temperature (Tcase) for the range of processors that the system will support (65oC). 3. Determine the Magnitude of the overshoot (relative to VSS) 4. Determine the Activity Factor (how often does this overshoot occur?) 5. From the appropriate Specification table, read off the Maximum Pulse Duration (in ns) allowed. 6. Compare the specified Maximum Pulse Duration to the signal being measured. If the Pulse Duration measured is less than the Pulse Duration shown in the table, then the signal meets the specifications. The above procedure is similar for undershoots after the undershoot waveform has been converted to look like an overshoot. Undershoot events must be analyzed separately from Overshoot events as they are mutually exclusive. Below is an example showing how the maximum pulse duration is determined for a given waveform.
Table 26. Example Platform Information
Required Information Maximum Platform Support Notes
PSB Signal Group Max Tcase Overshoot Magnitude Activity Factor (AF)
100 MHz AGTL 72 C 1.78 V 0.1 Measured Value Measured overshoot occurs on average every 20 clocks
Given the above parameters, and using Table 27 (65oC/AF = 0.1 column) the maximum allowed pulse duration is 7.5 ns. Since the measure pulse duration is 7.5 ns, this particular overshoot event passes the overshoot specifications, although this doesn't guarantee that the combined overshoot/ undershoot events meet the specifications.
Datasheet
45
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
3.2.6
Determining if a System Meets the Overshoot/Undershoot Specifications
The overshoot/undershoot specifications listed in the following tables specify the allowable overshoot/undershoot for a single overshoot/undershoot event. However most systems will have multiple overshoot and/or undershoot events that each have their own set of parameters (duration, AF and magnitude). While each overshoot on its own may meet the overshoot specification, when you add the total impact of all overshoot events, the system may fail. A guideline to ensure a system passes the overshoot and undershoot specifications is shown below. It is important to meet these guidelines; otherwise, contact your Intel field representative. 1. Insure no AGTL signal ever exceeds 1.78 V and no CMOS signal ever exceeds 2.08 V. OR 2. If only one overshoot/undershoot event magnitude occurs, ensure it meets the over/undershoot specifications in the following tables OR 3. If multiple overshoots and/or multiple undershoots occur, measure the worst case pulse duration for each magnitude and compare the results against the AF = 1 specifications. If all of these worst case overshoot or undershoot events meet the specifications (measured time < specifications) in the table (where AF=1), then the system passes. The following notes apply to Table 26 through Table 29.
NOTES:
1. Overshoot/Undershoot Magnitude = 1.78 V(AGTL), 2.08 V(CMOS) is an Absolute value and should never be exceeded 2. Overshoot is measured relative to VSS. 3. Undershoot is measured relative to VTT 4. Overshoot/Undershoot Pulse Duration is measured relative to 1.32 V for AGTL and 1.80 V for CMOS. 5. Rinbacks below VTT can not be subtracted from Overshoots/Undershoots 6. Lesser Undershoot does not allocate longer or larger Overshoot 7. OEM's are encouraged to follow Intel provided layout guidelines. Consult the layout guidelines provided in the specific platform design guide. 8. All values specified by design characterization Table 27. 100 MHz AGTL Signal Group Overshoot/Undershoot Tolerance 1, 2, 3
Overshoot/ Undershoot Magnitude (V) Maximum Pulse Duration at Tcase = 60 C (ns) AF = 0.01 AF = 0.1 AF = 1 Maximum Pulse Duration at Tcase = 69 C (ns) AF = 0.01 AF = 0.1 AF = 1 Maximum Pulse Duration at Tcase = 71 C (ns) AF = 0.01 AF = 0.1 AF = 1 Maximum Pulse Duration at Tcase = 72 C (ns) AF = 0.01 AF = 0.1 AF = 1
1.78 1.73 1.68 1.63 1.58 1.53 1.48
20 20 20 20 20 20 20
1.5 3.1 6.8 14 15 15 15
0.153 0.31 0.68 1.42 2.95 6.2 13.2
8.7 15 15 15 20 20 20
0.87 2.0 4.6 10 15 15 20
0.087 0.20 0.46 1.0 2.3 5.0 15
6 13 20 20 20 20 20
0.6 1.3 2.8 6.0 12.7 20 20
0.06 0.13 0.28 0.6 1.27 2.65 5.45
6 12 20 20 20 20 20
0.6 1.2 2.7 5.7 12 20 20
0.06 0.12 0.27 0.57 1.2 2.46 5.10
Notes: 1. Measurements taken at the processor socket pins on the solder-side of the motherboard. 2. Overshoot/Undershoot Magnitude = 1.78 V is an absolute value and should never be exceeded. 3. BCLK Period = 10.0 ns.
46
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 20. Maximum Acceptable AGTL Overshoot/Undershoot Waveform
0.1 ns 1.78 V Max 1.62 V 1.47 V 1.32 V a b c 0.3 ns 1 ns Vos_ref Time dependent Overshoot
a Vss -0.15 V -0.30 V -0.46 V Min
b
c
0.1 ns
0.3 ns
1 ns
Time dependent Undershoot
3.3
Non-AGTL Signal Quality Specifications and Measurement Guidelines
There are three signal quality parameters defined for non-AGTL signals: overshoot/undershoot, ringback, and settling limit. All three signal quality parameters are shown in Figure 21 for the nonAGTL signal group.
Figure 21. Non-AGTL Overshoot/Undershoot, Settling Limit, and Ringback 1
Overshoot VHI Settling Limit
Rising-Edge Ringback
Falling-Edge Ringback
Settling Limit
VLO
VSS
Time
Undershoot
NOTE: 1. VHI = 1.80 V for all non-AGTL signals except for BCLK, PICCLK, and PWRGOOD. VHI =2.0 V for PICCLK, and VHI =1.8 V for PWRGOOD. BCLK and PICCLK signal quality is detailed in Section 3.1.
Datasheet
47
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
3.3.1
Overshoot/Undershoot Guidelines
Overshoot (or undershoot) is the absolute value of the maximum voltage above the nominal high voltage or below VSS. The overshoot guideline limits transitions beyond VCC or VSS due to the fast signal edge rates (see Figure 21 for non-AGTL signals). The processor can be damaged by repeated overshoot events on 1.25 V or 1.8 V tolerant buffers if the charge is large enough (i.e., if the overshoot is great enough). Permanent damage to the processor is the likely result of excessive overshoot/undershoot. Violating the overshoot/undershoot guideline will also make satisfying the ringback specification difficult. The overshoot/undershoot guideline is 0.3 V and assumes the absence of diodes on the input. These guidelines should be verified in simulations without the onchip ESD protection diodes present because the diodes will begin clamping the 1.25 V and 2.5 V tolerant signals beginning at approximately 0.7 V above the appropriate supply and 0.7 V below VSS. If signals are not reaching the clamping voltage, this will not be an issue. A system should not rely on the diodes for overshoot/undershoot protection as this will negatively affect the life of the components and make meeting the ringback specification very difficult.
Table 28. 33 MHz CMOS Signal Group Overshoot/Undershoot Tolerance
Overshoot/ Undershoot Magnitude (V) Maximum Pulse Duration at Tcase = 69 C (ns) AF = 0.01 AF = 0.1 AF = 1 Maximum Pulse Duration at Tcase = 71 C (ns) AF = 0.01 AF = 0.1 AF = 1 Maximum Pulse Duration at Tcase = 72 C (ns) AF = 0.01 AF = 0.1 AF = 1
2.38 2.33 2.28 2.23 2.18 2.13 2.08
35 60 60 60 60 60 60
3.5 8.0 18 41 60 60 60
0.35 0.8 1.8 4.1 9.0 21 60
19 40 60 60 60 60 60
1.9 4.0 8.0 18 37.5 60 60
0.19 0.40 0.80 1.80 3.75 8.00 16.00
17 36 60 60 60 60 60
1.7 3.6 7.7 16 34 60 60
0.17 0.36 0.77 1.60 3.42 7.12 14.5
Note:
The undershoot guideline limits transitions exactly as described for the ATGL signals. See Figure 20.
3.3.2
Ringback Specification
Ringback refers to the amount of reflection seen after a signal has switched. The ringback specification is the voltage that the signal rings back to after achieving its maximum absolute value. See Figure 21 for an illustration of ringback. Excessive ringback can cause false signal detection or extend the propagation delay. The ringback specification applies to the input pin of each receiving agent. Violations of the signal ringback specification are not allowed under any circumstances for non-AGTL signals. Ringback can be simulated with or without the input protection diodes that can be added to the input buffer model. However, signals that reach the clamping voltage should be evaluated further. See Table 29 for the signal ringback specifications for non-AGTL signals for simulations at the processor pins.
48
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 29. Signal Ringback Specifications for Non-AGTL Signal Simulation at the Processor Pins
Input Signal Group Transition Maximum Ringback (with Input Diodes Present) Unit Figure
Non-AGTL Signals Non-AGTL Signals PWRGOOD
2 2
01 10 01
Vcmos_ref + 0.200 Vcmos_ref - 0.300 1.44
V V V
21 21 21
NOTES: 1. Unless otherwise noted, all specifications in this table apply to the processor up to 1.40 GHz frequency. 2. Non-AGTL signals except PWRGOOD.
3.3.3
Settling Limit Guideline
Settling limit defines the maximum amount of ringing at the receiving pin that a signal must reach before its next transition. The amount allowed is 10% of the total signal swing (VHI -VLO) above and below its final value. A signal should be within the settling limits of its final value, when either in its high state or low state, before it transitions again. Signals that are not within their settling limit before transitioning are at risk of unwanted oscillations which could jeopardize signal integrity. Simulations to verify settling limit may be done either with or without the input protection diodes present. Violation of the settling limit guideline is acceptable if simulations of 5 to 10 successive transitions do not show the amplitude of the ringing increasing in the subsequent transitions.
3.4
VTT_PWRGD Signal Quality Specification
The VTT_PWRGD signal is an input to the processor used to determine that the VTT power is stable and the VID and BSEL signals should be driven to their final state by the processor. To ensure the processor correctly reads this signal, it must meet the following requirement while the signal is in its transition region of 300 mV to 900 mV. Also, VTT_PWRGD should only enter the transition region once, after VTT is at nominal values, for the assertion of the signal.
Amount of noise (glitch) < 100 mV
In addition, the VTT_PWRGD signal should have a reasonable transition time through the transition region. A sharp edge on the signal transition will minimize the chance of noise causing a glitch on this signal. Intel recommends the following transition time for the VTT_PWRGD signal.
Transition time (300 mV to 900 mV) 100 us
3.4.1
Transition region
The transition region covered by this requirement is 300 mV to 900 mV. Once the VTT_PWRGD signal is in that voltage range, the processor is more sensitive to noise which may be present on the signal. The transition region when the signal first crosses the 300 mV voltage level and continues until the last time it is below 900 mV.
Datasheet
49
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
3.4.2
Transition time
The transition time is defined as the time the signal takes to move through the transition region. A 100 microsecond transition time will ensure that the processor receives a good transition edge.
3.4.3
Noise
The signal quality of the VTT_PWRGD signal is critical to the correct operation of the processor. Every effort should be made to ensure this signal is monotonic in the transition region. If noise or glitches are present on this signal, it must be kept to less than 100 mV of a voltage drop from the highest voltage level received to that point. This glitch must remain less than 100 mV until the excursion ends by the voltage returning to the highest voltage previously received. See Figure 22 for an example graph of this situation and requirements.
Figure 22. Noise Estimation
50
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
4.0
Thermal Specifications and Design Considerations
This chapter provides needed data for designing a thermal solution. However, for the correct thermal measuring processes, refer to Intel(R) Pentium(R) III Processor in the FC-PGA2, 370-pin Package Thermal Design Guidelines (Order Number 249660). The processor uses flip chip pin grid array packaging technology with a Integrated Heat Spreader and has a case temperature (Tcase) specified.
4.1
Thermal Specifications
Table 30 provides the thermal design power dissipation and maximum temperatures for the processor. Systems should design for the highest possible processor power, even if a processor with a lower thermal dissipation is planned. A thermal solution should be designed to ensure the case temperature never exceeds these specifications.
Table 30. Processor Thermal Design Power 1
Processor Processor Core Frequency L2 Cache Size (Kbytes) Processor Power 2 (W) Maximum TCASE (C)
1.404 1.304 1.20 1.205 1.10A 1A 900
1.40 1.30 GHz 1.20 GHz 1.20 GHz 1.10A GHz 1A GHz 900 MHz
256 256 256 256 256 256 256
34.8 33.4 32.1 29.9 28.9 27.8 26.3
72 71 70 69 69 69 69
1. These values are specified at nominal VCCCORE for the processor pins. 2. Processor power includes the power dissipated by the processor core, the L2 cache, and the AGTL bus termination. The maximum power for each of these components does not occur simultaneously. 3. Processor core power includes only the power dissipated by the core die. 4. For frequencies beyond 1.4 GHz, refer to the latest flexible motherboard 1 extended (FMB1-E) guidelines available via your Intel Representative. 5. 1.20 GHz at VccCORE = 1.475 volts and S-Spec number SL5XS.
4.1.1
THERMTRIP# Requirement
In the event the processor drives the THERMTRIP# signal active during valid operation, both the VCC and VTT supplies to the processor must be turned off to prevent thermal runaway of the processor. Valid operation refers to the operating conditions where the THERMTRIP# signal is guaranteed valid. The time required from THERMTRIP# asserted to VCC rail at 1/2 nominal is 5 s and THERMTRIP# asserted to VTT rail at 1/2 nominal is 5 s.
Table 31. THERMTRIP# Time Requirement
Power Rail Power Target Time Required for Power Drop
VCC VTT
1/2 Nominal VCC 1/2 Nominal VTT
5 seconds 5 seconds
NOTE: Once VCC and VTT supplies are turned off the THERMTRIP# signal will be deactivated. System logic should ensure no "unsafe" power cycling occurs due to this deassertion.
Datasheet
51
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
4.1.2
Thermal Diode
The processor incorporates an on-die diode that may be used to monitor the die temperature (junction temperature). A thermal sensor located on the motherboard, or a stand-alone measurement kit, may monitor the die temperature of the processor for thermal management or instrumentation purposes. Table 32 and Table 33 provide the diode parameter and interface specifications. The processor uses an Integrated Heat Spreader (IHS) and has a case temperature requirement. Please see the Intel(R) Pentium(R) III Processor in the FC-PGA2, 370-pin Package Thermal Design Guidelines document for details on measuring the case temperature. The thermal diode should be used for system thermal management and not determining spec compliance.
Table 32. Thermal Diode Parameters
Symbol Parameter Min Typ Max Unit Notes 1
Ifw n Ifw n
Forward Bias Current Diode Ideality Factor Forward Bias Current Diode Ideality Factor
5 1.001452 5 1.000807
N/A 1.007152 N/A 1.009528
150 1.012852 300 1.018249
A
1 2, 4, 5
A
1 3, 4, 5
NOTES: 1. Intel does not support or recommend operation of the thermal diode under reverse bias. 2. Characterized at 75 C with a forward bias current of 5 - 150 A. 3. Characterized at 75 C with a forward bias current of 5 - 300 A. 4. The ideality factor, n, represents the deviation from ideal diode behavior as exemplified by the diode equation: Ifw=Is(e^ ((Vd*q)/(nkT)) - 1), where Is = saturation current, q = electronic charge, Vd = voltage across the diode, k = Boltzmann Constant, and T = absolute temperature (Kelvin). 5. Not 100% tested. Specified by design characterization.
Table 33. Thermal Diode Interface
Pin Name PGA370 Socket pin # Pin Description
THERMDP THERMDN
AL31 AL29
diode anode (p_junction) diode cathode (n_junction)
4.2
Thermal Metrology
The thermal metrology for the processor in the FC-PGA2 package should be followed to evaluate the thermal performance of proposed cooling solutions. The thermal metrology is contained in the Intel(R) Pentium(R) III Processor in the FC-PGA2, 370-pin Package Thermal Design Guidelines. Please contact your local Intel field office to obtain this document.
52
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
5.0
Mechanical Specifications
The processor uses a FC-PGA2 package technology. Mechanical specifications for the processor are given in this section. See Section 1.1.1 for a complete terminology listing. The processor utilizes a PGA370 socket for installation into the motherboard. Details on the socket are available in the 370-Pin Socket (PGA370) Design Guidelines. Note: For Figure 23, the following apply: 1. Unless otherwise specified, the following drawings are dimensioned in inches. 2. All dimensions provided with tolerances are guaranteed to be met for all normal production product. 3. Figures and drawings labeled as "Reference Dimensions" are provided for informational purposes only. Reference dimensions are extracted from the mechanical design database and are nominal dimensions with no tolerance information applied. Reference dimensions are NOT checked as part of the processor manufacturing. Unless noted as such, dimensions in parentheses without tolerances are reference dimensions. 4. Drawings are not to scale.
5.1
FC-PGA2 Mechanical Specifications
The following figure with package dimensions is provided to aid in the design of heatsink and clip solutions as well as demonstrate where pin-side capacitors will be located on the processor. Table 34 includes the measurements for these dimensions in both inches and millimeters.
Figure 23. Package Dimensions
Datasheet
53
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 34. The Processor Package Dimensions
Millimeters Symbol Minimum Maximum Notes Minimum Maximum Notes Inches
A1 A2 B1 B2 C1 C2 D D1 G1 G2 G3 H L
P
2.266 0.980 30.800 30.800
2.690 1.180 31.200 31.200
0.089 0.038 1.212 1.212 1.299 max 1.299 max 1.946 1.790 0.000 0.000 0.000 Nominal 0.100 0.120 0.017
0.106 0.047 1.229 1.229
33.000 max 33.000 max 49.428 45.466 0.000 0.000 0.000 2.540 3.048 0.431 3.302 0.483 49.632 45.974 17.780 17.780 0.889
1.954 1.810 0.700 0.700 0.035 Nominal 0.130 0.019
Pin TP
0.508 Diametric True Position (Pin-to-Pin)
0.020 Diametric True Position (Pin-to-Pin)
NOTE: Capacitors will be placed on the pin-side of the FC-PGA2 package in the area defined by G1, G2, and G3. This area is a keepout zone for motherboard designers.
For Table 35, the following apply: 1. It is not recommended to use any portion of the processor substrate as a mechanical reference or load bearing surface for thermal solutions. 2. Parameters assume uniformly applied loads Table 35. Processor Case Loading Parameters
Parameter Dynamic (max)1 Static (max)2,3 Unit
IHS Surface IHS Edge IHS Corner
200 125 75
100 N/A N/A
lbf lbf ibf
NOTES: 1. This specification applies to a uniform and a non-uniform load. 2. This is the maximum static force that can be applied by the heatsink and clip to maintain the heatsink and processor interface. 3. Please see socket manufacturer's force loading specification also to ensure compliance. Maximum static loading listed here does not account for the maximum reaction forces on the socket tabs or pins.
54
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
5.2
Recommended Mechanical Keep-Out Zones
Figure 24. Volumetric Keep-Out
Figure 25. Component Keep-Out
Datasheet
55
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
5.3
Processor Markings
Figure 26 shows the processor top-side markings and it is provided to aid in the identification of the Celeron processor. Table 34 lists the measurements for the package dimensions.
Figure 26. Top Side Processor Markings
GRP1LN1 GRP1LN2
GRP2LN1 GRP2LN2
Production GRP1LN1: Intel'01 (m)(c)_-_{COO} GRP1LN2: {FPO}-{S/N} GRP2LN1: {core freq}/{cache size}/{PSB}/{VID} GRP2LN2: {S-spec here}
56
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
5.4
Processor Signal Listing
Table 36 and Table 37 provide the processor pin definitions. The signal locations on the PGA370 socket are to be used for signal routing, simulation, and component placement on the baseboard. Figure 27 provides a pin-side view of the processor pinout.
Figure 27. Processor Pinout
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
AN
DYN_OE A12 VSS A15 A28 VSS A10 VSS A35 A22 VSS A31 A20 VCC A24 A30 VSS A29 A26 RSV VSS A34 VSS VCC BERR D15 VCC D1 D5 RSV D12 VCC D2 VSS D13 VCC D7 VSS D21 D23 VCC VCC D25 VSS VSS VCC D35 VSS D29 D28 D31 VCC D43 VCC VCC D34 VSS D37 D30 D16 VSS D32 VSS D38 D36 VCC D44 D22 VCC D39 D45 VSS D51 RSV VSS D42 D49 VCC D47 D27 VCC D41 D40 VSS D48 VCC VSS D52 D59 VCC D57 D63 VCC VSS D55 VSS D46 VREF1 VSS VSS RSV VCC D54 VCC D53 VSS D58 VSS D60 VCC VTT VCC D50 VCC D61 VSS D62 VCC VSS VCC VSS D20 VREF2 VCC D19 D14 D11 VSS D24 VCC PICCLK VCC BP2 VCC VSS VTT VSS D10 D18 VCC D3 VCC RSV D17 VSS D9 VSS RSV VSS VCC VREF3 VSS D6 VREF4 VSS A32 VCC A18 VSS A23 VCC VREF5 VCC VSS VSS VTT VCC VSS A25 A5 A13 A3 A16 VCC A9 A11 VCC A8 A6 VSS AP0 VREF6 VSS A4 VCC BNR VTT VCC VTT A14 AP1 VSS A7 VTT VSS REQ1 VTT VCC REQ4 REQ0 VCC BPRI DEFER VSS VCC REQ3 LOCK VSS VTT VTT VTT VSS HITM AERR RP VCC HIT TRDY VSS DBSY PWRGD VCC VCC RS0 VSS DRDY VCC BR0 VSS ADS TRST VCC VSS TCK TMS VID0 VCC TDI VID1 TDO
AN AM
KEY VCC VSS VCC
AM AL AK AJ
A21 RESET2# VSS RESET A19 VCC VCC VCC RS1 VSS VCC RSV THRMDN RS2 THRMDP VID2 VttPWRGD CMOSREF VID25m V SMI VID3 VCC
AL AK
RSV BSEL1 SLP VCC INIT VSS A20M VSS
AJ AH
BSEL0 VSS
AH
REQ2 THERM TRIP
AG
VTT
AG
STPCLK VCC IGNNE DETECT FLUSH
AF AE
A17
AF AE
IERR VTT
AD AC
A33
AD AC
FERR VCC VTT RSV VTT RSP
AB AA
A27 VCC
AB AA Z
RSV BCLK#/ CLKREF VSS PLL1 VTT RSV VSS VTT VCC VSS VCC VTT
Z Y X W
D0 BCLK VCC VSS VSS
Y X W V
V U
D4
Pin Side View
VCC PLL2 VSS
U T S
T S
D8
R Q P N M L K J H G
RTT VTT VTT CTRL VCC VSS VCC RSV VCC RSV RSV VSS NCHCTRL LINT0 PICD1 VCC PICD0 VCC VTT VSS PREQ LINT1 RSV
R Q P N M L K J H G F
F E D C B A
D33 D26 SLEW DEP6 DEP4 VREF0 BPM1 BP3 CTRL VSS VCC VSS VCC VSS VCC D56 VSS DEP5 VCC DEP7 DEP3 DEP1 VSS DEP0 BPM0 VCC DEP2 CPUPRES
E D C B
BINIT
A
PRDY VSS
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37
Datasheet
57
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 36. Signal Listing in Order by Signal Name
Pin No. Pin Name Signal Group
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
AH6 AK10 AN5 AL7 AK14 AL5 AN7 AE1 Z6 AG3 AC3 AE33 AJ1 AE3 AB6 AB4 AF6 Y3 AA1 AK6 Z4 AK8 AA3 AD4 X6 AC1 W3 AF4 AH12 AH8 AN9 AL15 AH10 AL9 AN31 AK24 AL11 AN13 W37 Y33
A10# A11# A12# A13# A14# A15# A16# A17# A18# A19# A20# A20M# A21# A22# A23# A24# A25# A26# A27# A28# A29# A3# A30# A31# A32# A33# A34# A35# A4# A5# A6# A7# A8# A9# ADS# AERR# AP0# AP1# BCLK
BCLK#/CLKREF
AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O CMOS Input AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O System Bus Clock System Bus Clock
V4 B36 AH14 G33 E37 C35 E35 AN17 AN29 X2 AJ33 AJ31 C37 W1 T4 Q3 M4 Q1 L1 N3 U3 H4 R4 P4 H6 N1 L3 G1 F8 G3 K6 E3 E1 F12 A5 A3 M6 J3 C5 F6
BERR# BINIT# BNR# BP2# BP3# BPM0# BPM1# BPRI# BR0# Reserved BSEL0 BSEL1 CPUPRES# D0# D1# D10# D11# D12# D13# D14# D15# D16# D17# D18# D19# D2# D20# D21# D22# D23# D24# D25# D26# D27# D28# D29# D3# D30# D31# D32#
AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL Input AGTL I/O AGTL I/O 3.3V Output 3.3V Output Power/Other AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O
58
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
C1 C7 B2 C9 A9 D8 D10 U1 C15 D14 D12 A7 A11 C11 A21 A15 A17 C13 S3 C25 A13 D16 A23 C21 C19 C27 A19 C23 C17 T6 A25 A27 E25 F16 J1 S1 P6 AL27 AN19 C33
D33# D34# D35# D36# D37# D38# D39# D4# D40# D41# D42# D43# D44# D45# D46# D47# D48# D49# D5# D50# D51# D52# D53# D54# D55# D56# D57# D58# D59# D6# D60# D61# D62# D63# D7# D8# D9# DBSY# DEFER# DEP0#
AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL Input AGTL I/O
C31 A33 A31 E31 C29 E29 A29 AF36 AN27 AN3 AC35 AE37 AL25 AL23 AE35 AG37 AG33 AM2 M36 L37 AK20 N37 J33 J35 L35 W33 U33 A35 J37 AK26 AK18 AH16 AH18 AL19 AL17 AK30 AL1 F10 E21 L33
DEP1# DEP2# DEP3# DEP4# DEP5# DEP6# DEP7# DETECT DRDY# DYN_OE FERR# FLUSH# HIT# HITM# IERR# IGNNE# INIT# KEY LINT0/INTR LINT1/NMI LOCK# NCHCTRL PICCLK PICD0 PICD1 PLL1 PLL2 PRDY# PREQ# PWRGOOD REQ0# REQ1# REQ2# REQ3# REQ4# Reserved Reserved Reserved Reserved Reserved
AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O Power/Other AGTL I/O Power/Other CMOS Output CMOS Input AGTL I/O AGTL I/O CMOS Output CMOS Input CMOS Input Power/Other CMOS Input CMOS Input AGTL I/O Power/Other APIC Clock Input APIC I/O APIC I/O Power/Other Power/Other AGTL Output CMOS Input CMOS Input AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O Reserved for future use Reserved for future use Reserved for future use Reserved for future use Reserved for future use
Datasheet
59
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
N33 N35 Q33 Q35 Q37 R2 W35 Y1 Z36 AH4 AJ3 AN23 AH26 AH22 AK28 AC37 S35 E27 AH30 AJ35 AG35 AL33 AN35 AN37 AL29 AL31 AH28 AK32 AN25 AN33 AA37 AA5 AB2 AB34 AD32 AE5 AF2 AF34 AH24 AH32
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved RESET# RESET2# RP# RS0# RS1# RS2# RSP# RTTCTRL SLEWCTRL SLP# SMI# STPCLK# TCK TDI TDO THERMDN THERMDP THERMTRIP# TMS TRDY# TRST# VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE
Reserved for future use Reserved for future use Reserved for future use Reserved for future use Reserved for future use Reserved for future use Reserved for future use Reserved for future use Reserved for future use AGTL Input AGTL Input AGTL I/O AGTL + Input AGTL Input AGTL Input AGTL Input Power/Other Power/Other CMOS Input CMOS Input CMOS Input TAP Input TAP Input TAP Output Power/Other Power/Other CMOS Output TAP Input AGTL Input TAP Input Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other
AH36 AJ13 AJ17 AJ21 AJ25 AJ29 AJ5 AJ9 AK2 AK34 AM12 AM16 AM20 AM24 AM28 AM32 AM4 AM8 B10 B14 B18 B22 B26 B30 B34 B6 C3 D20 D24 D28 D32 D36 D6 E13 E17 E5 E9 F14 F2 F22
VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE
Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other
60
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
F26 F30 F34 F4 H32 H36 J5 K2 K32 K34 M32 N5 P2 P34 R32 R36 S5 T2 T34 V32 V36 W5 Y35 Z32 AK22 AK36 AL35 AM36 AL37 AJ37 E33 F18 K4 R6 V6 AD6 AK12 A37 AB32 AC33
VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCCCORE VCMOS_REF VID 25mV VID0 VID1 VID2 VID3 VREF0 VREF1 VREF2 VREF3 VREF4 VREF5 VREF6 Vss Vss Vss
Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other 3.3V Output 3.3V Output 3.3V Output 3.3V Output 3.3V Output Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other
AC5 AD2 AD34 AF32 AG5 AH2 AH34 AJ11 AJ15 AJ19 AJ23 AJ27 AJ7 AL3 AM10 AM14 AM18 AM22 AM26 AM30 AM34 AM6 B12 B16 B20 B24 B28 B32 B4 B8 D18 D2 D22 D26 D30 D34 D4 E11 E15 E19
Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss
Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other
Datasheet
61
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
Table 36. Signal Listing in Order by Signal Name (Continued)
Pin No. Pin Name Signal Group
E7 F20 F24 F28 F32 F36 G5 H2 H34 K36 L5 M2 M34 P32 P36 Q5 R34 T32 T36 U5 V2 V34 X32 X36 X4
Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss Vss
Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other
Y37 Y5 Z2 Z34 AB36 AD36 AG1 AH20 AK16 AL13 AL21 AN11 AN15 E23 G35 G37 S33 X34 AA33 AA35 AN21 S37 U35 U37 AK4
Vss Vss Vss Vss VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT VTT_PWRGD
Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other
62
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 37. Signal Listing in Order by Pin Number
Pin No. Pin Name Signal Group
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
A3 A5 A7 A9 A11 A13 A15 A17 A19 A21 A23 A25 A27 A29 A31 A33 A35 A37 AA1 AA3 AA5 AA33 AA35 AA37 AB2 AB4 AB6 AB32 AB34 AB36 AC1 AC3 AC5 AC33 AC35 AC37 AD2 AD4 AD6 AD32
D29# D28# D43# D37# D44# D51# D47# D48# D57# D46# D53# D60# D61# DEP7# DEP3# DEP2# PRDY# Vss A27# A30# VCCCORE VTT VTT VCCCORE VCCCORE A24# A23# Vss VCCCORE VTT A33# A20# Vss Vss FERR# RSP# Vss A31# VREF5 VCCCORE
AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL Output Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other CMOS Output AGTL Input Power/Other AGTL I/O Power/Other Power/Other
AD34 AD36 AE1 AE3 AE5 AE33 AE35 AE37 AF2 AF4 AF6 AF32 AF34 AF36 AG1 AG3 AG5 AG33 AG35 AG37 AH2 AH4 AH6 AH8 AH10 AH12 AH14 AH16 AH18 AH20 AH22 AH24 AH26 AH28 AH30 AH32 AH34 AH36 AJ1 AJ3
Vss VTT A17# A22# VCCCORE A20M# IERR# FLUSH# VCCCORE A35# A25# Vss VCCCORE DETECT VTT A19# Vss INIT# STPCLK# IGNNE# Vss RESET# A10# A5# A8# A4# BNR# REQ1# REQ2# VTT RS1# VCCCORE RS0# THERMTRIP# SLP# VCCCORE Vss VCCCORE A21# RESET2#
Power/Other Power/Other AGTL I/O AGTL I/O Power/Other CMOS Input CMOS Output CMOS Input Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other Power/Other AGTL I/O Power/Other CMOS Input CMOS Input CMOS Input Power/Other AGTL Input AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O Power/Other AGTL Input Power/Other AGTL + Input CMOS Output CMOS Input Power/Other Power/Other Power/Other AGTL I/O AGTL Input
Datasheet
63
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
AJ5 AJ7 AJ9 AJ11 AJ13 AJ15 AJ17 AJ19 AJ21 AJ23 AJ25 AJ27 AJ29 AJ31 AJ33 AJ35 AJ37 AK2 AK4 AK6 AK8 AK10 AK12 AK14 AK16 AK18 AK20 AK22 AK24 AK26 AK28 AK30 AK32 AK34 AK36 AL1 AL3 AL5 AL7 AL9
VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE BSEL1 BSEL0 SMI# VID3 VCCCORE VTT_PWRGD A28# A3# A11# VREF6 A14# VTT REQ0# LOCK# VCMOS_REF AERR# PWRGOOD RS2# Reserved TMS VCCCORE VID 25mV Reserved Vss A15# A13# A9#
Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other 3.3V Output 3.3V Output CMOS Input 3.3V Output Power/Other Power/Other AGTL I/O AGTL I/O AGTL I/O Power/Other AGTL I/O Power/Other AGTL I/O AGTL I/O Power/Other AGTL I/O CMOS Input AGTL Input Reserved for future use TAP Input Power/Other 3.3V Output Reserved for future use Power/Other AGTL I/O AGTL I/O AGTL I/O
AL11 AL13 AL15 AL17 AL19 AL21 AL23 AL25 AL27 AL29 AL31 AL33 AL35 AL37 AM2 AM4 AM6 AM8 AM10 AM12 AM14 AM16 AM18 AM20 AM22 AM24 AM26 AM28 AM30 AM32 AM34 AM36 AN3 AN5 AN7 AN9 AN11 AN13 AN15 AN17
AP0# VTT A7# REQ4# REQ3# VTT HITM# HIT# DBSY# THERMDN THERMDP TCK VID0 VID2 KEY VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VID1 DYN_OE A12# A16# A6# VTT AP1# VTT BPRI#
AGTL I/O Power/Other AGTL I/O AGTL I/O AGTL I/O Power/Other AGTL I/O AGTL I/O AGTL I/O Power/Other Power/Other TAP Input 3.3V Output 3.3V Output Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other 3.3V Output Power/Other AGTL I/O AGTL I/O AGTL I/O Power/Other AGTL I/O Power/Other AGTL Input
64
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
AN19 AN21 AN23 AN25 AN27 AN29 AN31 AN33 AN35 AN37 B2 B4 B6 B8 B10 B12 B14 B16 B18 B20 B22 B24 B26 B28 B30 B32 B34 B36 C1 C3 C5 C7 C9 C11 C13 C15 C17 C19 C21 C23
DEFER# VTT RP# TRDY# DRDY# BR0# ADS# TRST# TDI TDO D35# Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE BINIT# D33# VCCCORE D31# D34# D36# D45# D49# D40# D59# D55# D54# D58#
AGTL Input Power/Other AGTL I/O AGTL Input AGTL I/O AGTL I/O AGTL I/O TAP Input TAP Input TAP Output AGTL I/O Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O
C25 C27 C29 C31 C33 C35 C37 D2 D4 D6 D8 D10 D12 D14 D16 D18 D20 D22 D24 D26 D28 D30 D32 D34 D36 E1 E3 E5 E7 E9 E11 E13 E15 E17 E19 E21 E23 E25 E27 E29
D50# D56# DEP5# DEP1# DEP0# BPM0# CPUPRES# Vss Vss VCCCORE D38# D39# D42# D41# D52# Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE D26# D25# VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss Reserved VTT 4 D62# SLEWCTRL DEP6#
AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O Power/Other Power/Other Power/Other Power/Other AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Reserved for future use Power/Other AGTL I/O Power/Other AGTL I/O
Datasheet
65
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
E31 E33 E35 E37 F2 F4 F6 F8 F10 F12 F14 F16 F18 F20 F22 F24 F26 F28 F30 F32 F34 F36 G1 G3 G5 G33 G35 G37 H2 H4 H6 H32 H34 H36 J1 J3 J5 J33 J35 J37
DEP4# VREF0 BPM1# BP3# VCCCORE VCCCORE D32# D22# Reserved D27# VCCCORE D63# VREF1 Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss VCCCORE Vss D21# D23# Vss BP2# VTT VTT Vss D16# D19# VCCCORE Vss VCCCORE D7# D30# VCCCORE PICCLK PICD0 PREQ#
AGTL I/O Power/Other AGTL I/O AGTL I/O Power/Other Power/Other AGTL I/O AGTL I/O Reserved for future use AGTL I/O Power/Other AGTL I/O Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other AGTL I/O Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other APIC Clock Input APIC I/O CMOS Input
K2 K4 K6 K32 K34 K36 L1 L3 L5 L33 L35 L37 M2 M4 M6 M32 M34 M36 N1 N3 N5 N33 N35 Q33 P2 P4 P6 P32 P34 P36 Q1 Q3 Q5 N37 Q35 Q37 R2 R4 R6 R32
VCCCORE VREF2 D24# VCCCORE VCCCORE Vss D13# D20# Vss Reserved PICD1 LINT1/NMI Vss D11# D3# VCCCORE Vss LINT0/INTR D2# D14# VCCCORE Reserved Reserved Reserved VCCCORE D18# D9# Vss VCCCORE Vss D12# D10# Vss NCHCTRL Reserved Reserved Reserved D17# VREF3 VCCCORE
Power/Other Power/Other AGTL I/O Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Reserved for future use APIC I/O CMOS Input Power/Other AGTL I/O AGTL I/O Power/Other Power/Other CMOS Input AGTL I/O AGTL I/O Power/Other Reserved for future use Reserved for future use Reserved for future use Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Reserved for future use Reserved for future use Reserved for future use AGTL I/O Power/Other Power/Other
66
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
Table 37. Signal Listing in Order by Pin Number (Continued)
Pin No. Pin Name Signal Group
R34 R36 S1 S3 S5 S33 S35 S37 T2 T4 T6 T32 T34 T36 U1 U3 U5 U33 U35 U37 V2 V4 V6 V32 V34
Vss VCCCORE D8# D5# VCCCORE VTT RTTCTRL VTT VCCCORE D1# D6# Vss VCCCORE Vss D4# D15# Vss PLL2 VTT VTT Vss BERR# VREF4 VCCCORE Vss
Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Power/Other Power/Other Power/Other AGTL I/O Power/Other Power/Other Power/Other
V36 W1 W3 W5 W33 W35 W37 X2 X4 X6 X32 X34 X36 Y1 Y3 Y5 Y33 Y35 Y37 Z2 Z4 Z6 Z32 Z34 Z36
VCCCORE D0# A34# VCCCORE PLL1 Reserved BCLK Reserved Vss A32# Vss VTT Vss Reserved A26# Vss
BCLK#/CLKREF
Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Reserved for future use System Bus Clock AGTL I/O Power/Other AGTL I/O Power/Other Power/Other Power/Other Reserved for future use AGTL I/O Power/Other System Bus Clock Power/Other Power/Other Power/Other AGTL I/O AGTL I/O Power/Other Power/Other Reserved for future use
VCCCORE Vss Vss A29# A18# VCCCORE Vss Reserved
Datasheet
67
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
6.0
Boxed Processor Specifications
The processor for the PGA370 socket is also offered as an Intel boxed processor. Intel boxed processors are intended for system integrators who build systems from motherboards and standard components. The boxed processor will be supplied with an unattached fan heatsink. This section documents motherboard and system requirements for the fan heatsink that will be supplied with the boxed processor. This section is particularly important for OEMs that manufacture motherboards for system integrators. Unless otherwise noted, all figures in this section are dimensioned in inches. Figure 28 shows a mechanical representation of the boxed Intel processor in the Flip Chip Pin Grid Array 2 (FC-PGA2) package. Note: Drawings in this section reflect only the specifications on the Intel Boxed Processor product. These dimensions should not be used as a generic keep-out zone for all heatsinks. It is the system designer's responsibility to consider their proprietary solution when designing to the required keepout zone on their system platform and chassis. Refer to the Intel(R) Pentium(R) III processor Thermal/ Mechanical Functional Specification for further guidance. Contact your local Intel Sales Representative for this document.
Figure 28. Conceptual Boxed Processor for the PGA370 Socket
Fan
Heatsink Clip
Heatsink
6.1
6.1.1
Mechanical Specifications
Mechanical Specifications for the FC-PGA2 Package
This section documents the mechanical specifications of the boxed processor fan heatsink in the FC-PGA2 Package. The boxed processor in the FC-PGA2 Package ships with an un-attached fan heatsink. Figure 28 shows a mechanical representation of the boxed processor for the PGA370 socket in the Flip Chip Pin Grid Array 2 (FC-PGA2) package. The boxed processor fan heatsink is also asymmetrical in that the mechanical step feature, Figure 31, must sit over the socket's cam. The step allows the heatsink to securely interface with the processor in order to meet the processor's thermal requirements.
68
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
The dimensions for the boxed processor with the integrated fan heatsink are shown in Figure 30. All dimensions are in inches. The processor uses a new technology termed FC-PGA2. The FC-PGA2 package leverages the previous FC-PGA package technology used on processors based on the 0.18 micron process. The FC-PGA2 package adds an Integrated Heat Spreader (IHS) to improve heat conduction from the processor die. This new solution prevent the need for exotic thermal solutions in the higher power density processors. See section 5.0 of this document for the mechanical specifications of the PGA370 socket. Section 5.2 of this document also shows the recommended mechanical keepout zones for the boxed processor fan heatink assembly. Figure 24 and Figure 25 show the REQUIRED keepout dimensions for the boxed processor thermal solution. The cooling fin orientation on the heatsink relative to the PGA370 socket is subject to change. Contact your local Intel Sales Representative for documentation specific to the boxed fan heatsink orientation relative to the PGA370 socket. Figure 31 shows the changes to the package mechanicals between the FC-PGA and FC-PGA2 designs. Note that the boxed fan heatsinks and associated clips are not compatible with earlier boxed fan heatsinks for processors based on the 0.18 micron process. Figure 29. Comparison between FC-PGA and FC-PGA2 package
FC-PGA 1.9 mm FC-PGA2 3.5 mm
49.5 mm square
3.2 mm
49.5 mm square
3.2 mm
Figure 30. Side View of Space Requirements for the Boxed Processor
3.11
2.65
1.89
1.89
1.76 3.17
Datasheet
69
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 38. Boxed Processor Fan Heatsink Spatial Dimensions
Dimensions (Inches) Min Typ Max Units
Fan Heatsink Length Fan Heatsink Height Fan Heatsink Width Fan Heatsink height above motherboard Air Keepout Zones from end of Fan Heatsink 0.29 0.20 0.30
3.14 1.81 2.6 0.33
Inches Inches Inches Inches Inches
Figure 31. Dimensions of Mechanical Step Feature in Heatsink Base
0.043 0.472 Units = inches
6.1.2
Boxed Processor Heatsink Weight
The boxed processor thermal cooling solution will not weigh more than 180 grams.
6.2
Thermal Specifications
This section describes the cooling requirements of the thermal cooling solution utilized by the boxed processor.
6.2.1
Boxed Processor Cooling Requirements
The boxed processor is directly cooled with a fan heatsink. However, meeting the processor's temperature specification is also a function of the thermal design of the entire system and ultimately the responsibility of the system integrator. The processor temperature specification is found in Section 4.1 of this document. The boxed processor fan heatsink is able to keep the processor temperature within the specifications (see Table 30 in Section 4.1) in chassis that provide good thermal management. For the boxed processor fan heatsink to operate properly, it is critical that the airflow provided to the fan heatsink is unimpeded. Airflow of the fan heatsink is into the center and out of the sides of the fan heatsink. Airspace is required around the fan to ensure that the airflow through the fan heatsink is not blocked. Blocking the airflow to the fan heatsink reduces the cooling efficiency and decreases fan life. Figure 32 illustrate an acceptable airspace clearance for the fan heatsink. It is
70
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
also recommended that the air temperature entering the fan be kept below 45 degrees C. Again, meeting the processor's temperature specification is the responsibility of the system integrator. The processor temperature specification is found in Section 4.1 of this document. Figure 32. Thermal Airspace Requirement for all Boxed Processor Fan Heatsinks in the PGA370 Socket
Measure ambient temperature 0.3 inches above center of fan inlet 0.20 inches min. air space 0.20 inches min. air space
Fan Heatsink Processor PGA-370 Socket
6.2.2
Boxed Processor Thermal Cooling Solution Clip
The boxed processor thermal solution requires installation by a system integrator to secure the thermal cooling solution to the processor after it is installed in the 370-pin socket ZIF socket. Motherboards designed for use by system integrators should take care to consider the implications of clip installation and potential scraping of the motherboard PCB underneath the 370-pin socket attach tabs. Motherboard components should not be placed too close to the 370-pin socket attach tabs in a way that interferes with the installation of the boxed processor thermal cooling solution Figure 24 and Figure 25 show the REQUIRED keepout dimensions for the boxed processor thermal solution.
6.3
6.3.1
Electrical Requirements for the Boxed Processor
Electrical Requirements
The boxed processor's fan heatsink requires a +12 V power supply. A fan power cable is attached to the fan and will draw power from a power header on the motherboard. The power cable connector and pinout are shown in Figure 33. Motherboards must provide a matched power header to support the boxed processor. Table 38 contains specifications for the input and output signals at the fan heatsink connector. The fan heatsink outputs a SENSE signal (an open-collector output) that pulses at a rate of two pulses per fan revolution. A motherboard pull-up resistor provides VOH to match the motherboard-mounted fan speed monitor requirements, if applicable. Use of the SENSE signal is optional. If the SENSE signal is not used, pin 3 of the connector should be tied to GND. The power header on the baseboard must be positioned to allow the fan heatsink power cable to reach it. The power header identification and location should be documented in the motherboard documentation or on the motherboard. Figure 34 shows the recommended location of the fan power connector relative to the PGA370 socket. The motherboard power header should be positioned within 4.00 inches (lateral) of the fan power connector for the FC-PGA2 package.
Datasheet
71
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Figure 33. Boxed Processor Fan Heatsink Power Cable Connector Description
Pin 1 2 3 Signal GND +12V SENSE Straight square pin, 3-pin terminal housing with polarizing ribs and friction locking ramp. 0.100" pin pitch, 0.025" square pin width. Waldom/Molex P/N 22-01-3037 or equivalent. Match with straight pin, friction lock header on motherboard Waldom/Molex P/N 22-23-2031, AMP P/N 640456-3, or equivalent. 1 2 3
Table 39. Fan Heatsink Power and Signal Specifications
Description Min Typ Max
+12 V: 12 volt fan power supply IC: Fan current draw SENSE: SENSE frequency (motherboard should pull this pin up to appropriate VCC with resistor)
10.8 V
12 V
13.2 V 100 mA
2 pulses per fan revolution
Figure 34. Motherboard Power Header Placement Relative to the Boxed Processor
0.10"
R = 4.00"
PGA370 Socket 7
0.10"
72
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
7.0
Processor Signal Description
This section provides an alphabetical listing of all the processor signals. The tables at the end of this section summarize the signals by direction: output, input, and I/O.
7.1
Alphabetical Signals Reference
Table 40. Signal Description (Sheet 1 of 8)
Name Type Description
A20M#
I
If the A20M# (Address-20 Mask) input signal is asserted, the processor masks physical address bit 20 (A20#) before looking up a line in any internal cache and before driving a read/write transaction on the bus. Asserting A20M# emulates the 8086 processor's address wrap-around at the 1 MB boundary. Assertion of A20M# is only supported in real mode. A20M# is an asynchronous signal. However, to ensure recognition of this signal following an I/O write instruction, it must be valid along with the TRDY# assertion of the corresponding I/O Write bus transaction. The A[35:3]# (Address) signals define a 236-byte physical memory address space. When ADS# is active, these pins transmit the address of a transaction; when ADS# is inactive, these pins transmit transaction type information. These signals must connect the appropriate pins of all agents on the processor system bus. The A[35:24]# signals are parity-protected by the AP1# parity signal, and the A[23:3]# signals are parity-protected by the AP0# parity signal. On the active-to-inactive transition of RESET#, the processors sample the A[35:3]# pins to determine their power-on configuration. See the Intel(R) Pentium(R) II Processor Developer's Manual for details. The ADS# (Address Strobe) signal is asserted to indicate the validity of the transaction address on the A[35:3]# pins. All bus agents observe the ADS# activation to begin parity checking, protocol checking, address decode, internal snoop, or deferred reply ID match operations associated with the new transaction. This signal must connect the appropriate pins on all processor system bus agents. The AERR# (Address Parity Error) signal is observed and driven by all processor system bus agents, and if used, must connect the appropriate pins on all processor system bus agents. AERR# observation is optionally enabled during power-on configuration; if enabled, a valid assertion of AERR# aborts the current transaction. If AERR# observation is disabled during power-on configuration, a central agent may handle an assertion of AERR# as appropriate to the error handling architecture of the system. The AP[1:0]# (Address Parity) signals are driven by the request initiator along with ADS#, A[35:3]#, REQ[4:0]#, and RP#. AP1# covers A[35:24]#, and AP0# covers A[23:3]#. A correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. This allows parity to be high when all the covered signals are high. AP[1:0]# should connect the appropriate pins of all processor system bus agents. The BCLK (Bus Clock) and BCLK# (for differential clock) signals determines the bus frequency. All processor system bus agents must receive this signal to drive their outputs and latch their inputs on the rising edge of BCLK. For differential clocking, all processor system bus agents must receive this signal to drive their outputs and latch their inputs on the BCLK and BCLK# crossing point. All external timing parameters are specified with respect to the BCLK signal.
A[35:3]#
I/O
ADS#
I/O
AERR#
I/O
AP[1:0]#
I/O
BCLK/BCLK#
I
Datasheet
73
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 40. Signal Description (Sheet 2 of 8)
Name Type Description
The BERR# (Bus Error) signal is asserted to indicate an unrecoverable error without a bus protocol violation. It may be driven by all processor system bus agents, and must connect the appropriate pins of all such agents, if used. However, the processor does not observe assertions of the BERR# signal. BERR# I/O BERR# assertion conditions are configurable at a system level. Assertion options are defined by the following options: * Enabled or disabled. * Asserted optionally for internal errors along with IERR#. * Asserted optionally by the request initiator of a bus transaction after it observes an error. * Asserted by any bus agent when it observes an error in a bus transaction. The BINIT# (Bus Initialization) signal may be observed and driven by all processor system bus agents, and if used must connect the appropriate pins of all such agents. If the BINIT# driver is enabled during power on configuration, BINIT# is asserted to signal any bus condition that prevents reliable future information. BINIT# I/O If BINIT# observation is enabled during power-on configuration, and BINIT# is sampled asserted, all bus state machines are reset and any data which was in transit is lost. All agents reset their rotating ID for bus arbitration to the state after Reset, and internal count information is lost. The L1 and L2 caches are not affected. If BINIT# observation is disabled during power-on configuration, a central agent may handle an assertion of BINIT# as appropriate to the error handling architecture of the system. The BNR# (Block Next Request) signal is used to assert a bus stall by any bus agent who is unable to accept new bus transactions. During a bus stall, the current bus owner cannot issue any new transactions. BNR# I/O Since multiple agents might need to request a bus stall at the same time, BNR# is a wire-OR signal which must connect the appropriate pins of all processor system bus agents. In order to avoid wire-OR glitches associated with simultaneous edge transitions driven by multiple drivers, BNR# is activated on specific clock edges and sampled on specific clock edges. The BP[3:2]# (Breakpoint) signals are outputs from the processor that indicate the status of breakpoints. The BPM[1:0]# (Breakpoint Monitor) signals are breakpoint and performance monitor signals. They are outputs from the processor which indicate the status of breakpoints and programmable counters used for monitoring processor performance. The BPRI# (Bus Priority Request) signal is used to arbitrate for ownership of the processor system bus. It must connect the appropriate pins of all processor system bus agents. Observing BPRI# active (as asserted by the priority agent) causes all other agents to stop issuing new requests, unless such requests are part of an ongoing locked operation. The priority agent keeps BPRI# asserted until all of its requests are completed, then releases the bus by deasserting BPRI#. The BR0# (Bus Request) pins drive the BREQ[0]# signal in the system. During power-up configuration, the central agent asserts the BR0# bus signal in the system to assign the symmetric agent ID to the processor. The processor samples its BR0# pin on the active-to-inactive transition of the RESET# to obtain its symmetric agent ID. The processor asserts the BR0# pin to request the system bus. BR0# must be connected to a 10-56 resistor to VSS. Refer to the platform design guide for implementation detail and resistor tolerance.
BP[3:2]#
I/O
BPM[1:0]#
I/O
BPRI#
I
BR0#
I/O
74
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 40. Signal Description (Sheet 3 of 8)
Name Type Description
BSEL[1:0]
O
The BSEL signals are CMOS signals which are used to select the system bus frequency. A BSEL[1:0] = `01' selects a 100 MHz system bus frequency. The frequency is determined by the processor(s), chipset, and frequency synthesizer capabilities. All system bus agents must operate at the same frequency. The processor operates at 100 MHz system bus frequency. These signals must be pulled up to 3.3V power rail with 330 - 1 K resistors and provided as a frequency selection signal to the clock driver/synthesizer and chipset. Refer to the platform design guide for implementation detail and resistor tolerance. In Single-ended clock mode the CLKREF input is a filtered 1.25V supply voltage for the processor PLL. A voltage divider and decoupling solution is provided by the motherboard. See the design guide for implementation details. When the processor operates in differential clock mode, this signal becomes BCLK#. The CPUPRES# signal is defined to allow a system design to detect the presence of a processor in a PGA370 socket. Combined with the VID combination of VID[25mV,3:0]= 11111 (see Section 2.6), a system can determine if a socket is occupied, and whether a processor core is present. See the table below for states and values for determining the presence of a device. PGA370 Socket Occupation Truth Table
CLKREF
I
CPUPRES#
O
Signal
Value
Status
CPUPRES# VID[25mV,3:0] CPUPRES# VID[25mV,3:0]
0 Anything other than `11111' 1 Any value
Processor core installed in the PGA370 socket. PGA370 socket not occupied.
D[63:0]#
I/O
The D[63:0]# (Data) signals are the data signals. These signals provide a 64-bit data path between the processor system bus agents, and must connect the appropriate pins on all such agents. The data driver asserts DRDY# to indicate a valid data transfer. The DBSY# (Data Bus Busy) signal is asserted by the agent responsible for driving data on the processor system bus to indicate that the data bus is in use. The data bus is released after DBSY# is deasserted. This signal must connect the appropriate pins on all processor system bus agents. The DEFER# signal is asserted by an agent to indicate that a transaction cannot be guaranteed in-order completion. Assertion of DEFER# is normally the responsibility of the addressed memory or I/O agent. This signal must connect the appropriate pins of all processor system bus agents. The DEP[7:0]# (Data Bus ECC Protection) signals provide optional ECC protection for the data bus. They are driven by the agent responsible for driving D[63:0]#, and must connect the appropriate pins of all processor system bus agents which use them. The DEP[7:0]# signals are enabled or disabled for ECC protection during power on configuration. A tri-state (high-impedance) output. Can be used for platforms that need to differentiate the previous generation Intel Celeron processors for the PGA370 socket that support VTT = 1.50 V from the new processors (AF36=VSS) that support VTT = 1.25 V . The output on this signal is stable when VTT is stable. Refer to the appropriate Platform Design Guide for implementation details. The DRDY# (Data Ready) signal is asserted by the data driver on each data transfer, indicating valid data on the data bus. In a multi-cycle data transfer, DRDY# may be deasserted to insert idle clocks. This signal must connect the appropriate pins of all processor system bus agents.
DBSY#
I/O
DEFER#
I
DEP[7:0]#
I/O
DETECT
O
DRDY#
I/O
Datasheet
75
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 40. Signal Description (Sheet 4 of 8)
Name Type Description
DYN_OE
I
The DYN_OE allows the BSEL and VID signals to be driven out from the processor. When this signal is low (a condition that will occur if the processor is installed in a non-supported platform), the VID and BSEL signals will be tri-stated and the platform pull-up resistors will set the VID and BSEL to all 1s which is a safe setting. This signal must be connected to a 1 k resistor to VTT. Refer to the platform design guide for implementation detail and resistor tolerance. The FERR# (Floating-point Error) signal is asserted when the processor detects an unmasked floating-point error. FERR# is similar to the ERROR# signal on the Intel 387 coprocessor, and is included for compatibility with systems using MS-DOS*-type floating-point error reporting. When the FLUSH# input signal is asserted, processors write back all data in the Modified state from their internal caches and invalidate all internal cache lines. At the completion of this operation, the processor issues a Flush Acknowledge transaction. The processor does not cache any new data while the FLUSH# signal remains asserted.
FERR#
O
FLUSH#
I
FLUSH# is an asynchronous signal. However, to ensure recognition of this signal following an I/O write instruction, it must be valid along with the TRDY# assertion of the corresponding I/O Write bus transaction. On the active-to-inactive transition of RESET#, each processor samples FLUSH# to determine its power-on configuration. See the P6 Family of Processors Hardware Developer's Manual for details. This signal must be connected to a 150 resistor to VCCCMOS1.5. Refer to the platform design guide for implementation detail and resistor tolerance.
HIT# HITM#
I/O I/O
The HIT# (Snoop Hit) and HITM# (Hit Modified) signals convey transaction snoop operation results, and must connect the appropriate pins of all processor system bus agents. Any such agent may assert both HIT# and HITM# together to indicate that it requires a snoop stall, which can be continued by reasserting HIT# and HITM# together. The IERR# (Internal Error) signal is asserted by a processor as the result of an internal error. Assertion of IERR# is usually accompanied by a SHUTDOWN transaction on the processor system bus. This transaction may optionally be converted to an external error signal (e.g., NMI) by system core logic. The processor will keep IERR# asserted until the assertion of RESET#, BINIT#, or INIT#. The IGNNE# (Ignore Numeric Error) signal is asserted to force the processor to ignore a numeric error and continue to execute noncontrol floating-point instructions. If IGNNE# is deasserted, the processor generates an exception on a noncontrol floating-point instruction if a previous floating-point instruction caused an error. IGNNE# has no effect when the NE bit in control register 0 is set. IGNNE# is an asynchronous signal. However, to ensure recognition of this signal following an I/O write instruction, it must be valid along with the TRDY# assertion of the corresponding I/O Write bus transaction. The INIT# (Initialization) signal, when asserted, resets integer registers inside all processors without affecting their internal (L1 or L2) caches or floating-point registers. Each processor then begins execution at the power-on Reset vector configured during power-on configuration. The processor continues to handle snoop requests during INIT# assertion. INIT# is an asynchronous signal and must connect the appropriate pins of all processor system bus agents. If INIT# is sampled active on the active to inactive transition of RESET#, then the processor executes its Built-in Self-Test (BIST). Can be used to prevent legacy processors from booting in incompatible platforms. Legacy processors use this pin as a RESET and should be tied to ground for a 0.13 micron process processor only platform but for flexible platform implementations this pin should be a No Connect. Please refer to the appropriate Platform Design Guide for implementation details.
IERR#
O
IGNNE#
I
INIT#
I
KEY
I
76
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 40. Signal Description (Sheet 5 of 8)
Name Type Description
LINT[1:0]
I
The LINT[1:0] (Local APIC Interrupt) signals must connect the appropriate pins of all APIC Bus agents, including all processors and the core logic or I/O APIC component. When the APIC is disabled, the LINT0 signal becomes INTR, a maskable interrupt request signal, and LINT1 becomes NMI, a nonmaskable interrupt. INTR and NMI are backward compatible with the signals of those names on the Intel Pentium processor. Both signals are asynchronous. Both of these signals must be software configured via BIOS programming of the APIC register space to be used either as NMI/INTR or LINT[1:0]. Because the APIC is enabled by default after Reset, operation of these pins as LINT[1:0] is the default configuration. The LOCK# signal indicates to the system that a transaction must occur atomically. This signal must connect the appropriate pins of all processor system bus agents. For a locked sequence of transactions, LOCK# is asserted from the beginning of the first transaction end of the last transaction. When the priority agent asserts BPRI# to arbitrate for ownership of the processor system bus, it will wait until it observes LOCK# deasserted. This enables symmetric agents to retain ownership of the processor system bus throughout the bus locked operation and ensure the atomicity of lock. The NCHCTRL input signal provides AGTL pull-down strength control. The processor samples this input to determine the N-channel device strength for pulldown when it is the driving agent. This signal must be connected to a 14ohm resistor to VTT. Refer to the platform design guide for implementation detail and resistor tolerance. The PICCLK (APIC Clock) signal is an input clock to the processor and core logic or I/O APIC which is required for operation of all processors, core logic, and I/O APIC components on the APIC bus. The PICD[1:0] (APIC Data) signals are used for bidirectional serial message passing on the APIC bus, and must connect the appropriate pins of all processors and core logic or I/O APIC components on the APIC bus. The processor has an internal analog PLL clock generator that requires a quiet power supply. PLL1 and PLL2 are inputs to this PLL and must be connected to VCCCORE through a low pass filter that minimizes jitter. See the platform design guide for implementation details. The PRDY (Probe Ready) signal is a processor output used by debug tools to determine processor debug readiness. The PREQ# (Probe Request) signal is used by debug tools to request debug operation of the processors. The PWRGOOD (Power Good) signal is processor input. The processor requires this signal to be a clean indication that the clocks and power supplies (VCCCORE, etc.) are stable and within their specifications. Clean implies that the signal will remain low (capable of sinking leakage current), without glitches, from the time that the power supplies are turned on until they come within specification. The signal must then transition monotonically to a high state. PWRGOOD can be driven inactive at any time, but clocks and power must again be stable before a subsequent rising edge of PWRGOOD. It must also meet the minimum pulse width specification in Table 18, and be followed by a 1 ms RESET# pulse. The PWRGOOD signal must be supplied to the processor; it is used to protect internal circuits against voltage sequencing issues. It should be driven high throughout boundary scan operation.
LOCK#
I/O
NCHCTRL
I
PICCLK
I
PICD[1:0]
I/O
PLL1, PLL2
I
PRDY# PREQ#
O I
PWRGOOD
I
REQ[4:0]#
I/O
The REQ[4:0]# (Request Command) signals must connect the appropriate pins of all processor system bus agents. They are asserted by the current bus owner over two clock cycles to define the currently active transaction type.
Datasheet
77
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 40. Signal Description (Sheet 6 of 8)
Name Type Description
Asserting the RESET# signal resets all processors to known states and invalidates their L1 and L2 caches without writing back any of their contents. For a power-on Reset, RESET# must stay active for at least one millisecond after VCCCORE and CLK have reached their proper specifications. On observing active RESET#, all processor system bus agents will deassert their outputs within two clocks. A number of bus signals are sampled at the active-to-inactive transition of RESET# for power-on configuration. These configuration options are described in the P6 Family of Processors Hardware Developer's Manual for details. RESET# I The processor may have its outputs tristated via power-on configuration. Otherwise, if INIT# is sampled active during the active-to-inactive transition of RESET#, the processor will execute its Built-in Self-Test (BIST). Whether or not BIST is executed, the processor will begin program execution at the power on Reset vector (default 0_FFFF_FFF0h). RESET# must connect the appropriate pins of all processor system bus agents. RESET# is the only AGTL signal which does not have on-die termination. Therefore, it is necessary to place a discrete 56 resistor to VTT. Refer to the platform design guide for implementation detail and resistor tolerance. RESET2# pin is provided to differentiate the processor from the previous generation Intel Celeron processor. The 0.13 micron process based processor does not use the RESET2# pin. Refer to the platform design guide for the proper connections of this signal. The RP# (Request Parity) signal is driven by the request initiator, and provides parity protection on ADS# and REQ[4:0]#. It must connect the appropriate pins of all processor system bus agents. A correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. This definition allows parity to be high when all covered signals are high. The RS[2:0]# (Response Status) signals are driven by the response agent (the agent responsible for completion of the current transaction), and must connect the appropriate pins of all processor system bus agents. The RSP# (Response Parity) signal is driven by the response agent (the agent responsible for completion of the current transaction) during assertion of RS[2:0]#, the signals for which RSP# provides parity protection. It must connect the appropriate pins of all processor system bus agents. A correct parity signal is high if an even number of covered signals are low and low if an odd number of covered signals are low. While RS[2:0]# = 000, RSP# is also high, since this indicates it is not being driven by any agent guaranteeing correct parity. The RTTCTRL input signal provides AGTL termination control. The processor samples this input to set the termination resistance value for the on-die AGTL termination. This signal must be connected to a 56 resistor to VSS on a uniprocessor platform or a 68 resistor to VSS on a dual-processor platform. Refer to the platform design guide for implementation detail and resistor tolerance. The SLEWCTRL input signal provides AGTL slew rate control. The processor samples this input to determine the slew rate for AGTL signals when it is the driving agent. This signal must be connected to a 110 resistor to VSS. Refer to the platform design guide for implementation detail and resistor tolerance. The SLP# (Sleep) signal, when asserted in Stop-Grant state, causes processors to enter the Sleep state. During Sleep state, the processor stops providing internal clock signals to all units, leaving only the Phase-Locked Loop (PLL) still operating. Processors in this state will not recognize snoops or interrupts. The processor will recognize only assertions of the SLP#, STPCLK#, and RESET# signals while in Sleep state. If SLP# is deasserted, the processor exits Sleep state and returns to Stop-Grant state, restarting its internal clock signals to the bus and APIC processor core units.
RESET2#
I
RP#
I/O
RS[2:0]#
I/O
RSP#
I
RTTCTRL
I
SLEWCTRL
I
SLP#
I
78
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 40. Signal Description (Sheet 7 of 8)
Name Type Description
SMI#
I
The SMI# (System Management Interrupt) signal is asserted asynchronously by system logic. On accepting a System Management Interrupt, processors save the current state and enter System Management Mode (SMM). An SMI Acknowledge transaction is issued, and the processor begins program execution from the SMM handler. The STPCLK# (Stop Clock) signal, when asserted, causes processors to enter a low power state. The processor stops providing internal clock signals to all processor core units except the bus and APIC units. The processor continues to snoop bus transactions and latch interrupts. When STPCLK# is deasserted, the processor restarts its internal clock to all units, services pending interrupts, and resumes execution. The assertion of STPCLK# has no effect on the bus clock; STPCLK# is an asynchronous input. The TCK (Test Clock) signal provides the clock input for the processor Test Bus (also known as the Test Access Port). The TDI (Test Data In) signal transfers serial test data into the processor. TDI provides the serial input needed for JTAG specification support. The TDO (Test Data Out) signal transfers serial test data out of the processor. TDO provides the serial output needed for JTAG specification support. Thermal Diode Cathode. This signal is used to calculate core (junction) temperature. See Section 4.1. Thermal Diode Anode. This signal is used to calculate core (junction) temperature. See Section 4.1. The processor protects itself from catastrophic overheating by use of an internal thermal sensor. This sensor is set well above the normal operating temperature to ensure that there are no false trips. The processor will stop all execution when the junction temperature exceeds approximately 135 C. This is signaled to the system by the THERMTRIP# (Thermal Trip) pin. Once activated, the signal remains latched, and the processor stopped, until RESET# goes active or core power is removed. There is no hysteresis built into the thermal sensor itself; as long as the die temperature drops below the trip level, a RESET# pulse will reset the processor and execution will continue. If the temperature has not dropped below the trip level, the processor will continue to drive THERMTRIP# and remain stopped. In the event the processor drives the THERMTRIP# signal active during valid operation, both the VCC and VTT supplies to the processor must be turned off to prevent thermal runaway of the processor. Valid operation refers to the operating conditions where the THERMTRIP# signal is guaranteed valid. The time required from THERMTRIP# asserted to VCC rail at 1/2 nominal is 5 seconds and THERMTRIP# asserted to VTT rail at 1/2 nominal is 5 seconds. Once Vcc and VTT supplies are turned off the THERMTRIP# signal will be deactivated. System logic should ensure no "unsafe" power cycling occurs due to this deassertion.
STPCLK#
I
TCK TDI TDO THERMDN THERMDP
I I O O I
THERMTRIP#
O
TMS
I
The TMS (Test Mode Select) signal is a JTAG specification support signal used by debug tools. The TRDY# (Target Ready) signal is asserted by the target to indicate that it is ready to receive a write or implicit writeback data transfer. TRDY# must connect the appropriate pins of all processor system bus agents. The TRST# (Test Reset) signal resets the Test Access Port (TAP) logic. TRST# must be driven low during power on Reset. The VCMOS_REF input pin supplies non-AGTL reference voltage, which is typically 2/3 of VCMOS. VCMOS_REF is used by the non-AGTL receivers to determine if a signal is a logical 0 or a logical 1. The Thevenin equivalent impedance of the VCMOS_REF generation circuits must be less than 0.5 k/1 k (i.e., top resistor 500 , bottom resistor 1 k).
TRDY#
I/O
TRST#
I
VCMOS_REF
I
Datasheet
79
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 40. Signal Description (Sheet 8 of 8)
Name Type Description
VID [3:0,25mV]
O
The VID[3:0, 25 mV] (Voltage ID) pins can be used to support automatic selection of power supply voltages. These pins are CMOS signals that must be pulled up to 3.3 V power rail with 1 K resistors. The VID pins are needed to cleanly support voltage specification variations on processors. See Table 3 for definitions of these pins. The power supply must supply the voltage that is requested by these pins, or disable itself. The VREF input pins supply the AGTL reference voltage, which is typically 2/3 of VTT. VREF is used by the AGTL receivers to determine if a signal is a logical 0 or a logical 1. The VTT_PWRGD signal informs the system that the VID/BSEL signals are in their correct logic state. During Power-up, the VID signals will be in an indeterminate state for a small period of time. The voltage regulator or the VRM should not sample and/or latch the VID signals until the VTT_PWRGD signal is asserted. The assertion of the VTT_PWRGD signal indicates the VID signals are stable and are driven to the final state by the processor. Refer to Figure 6 for power-up timing sequence for the VTT_PWRGD and the VID signals
VREF
I
VTT_PWRGD
I
7.2
Signal Summaries
Table 41 through Table 44 list attributes of the processor output, input, and I/O signals.
Table 41. Output Signals
Name Active Level Clock Signal Group
BSEL[1:0] CPUPRES# DETECT FERR# IERR# PRDY# TDO THERMTRIP# VID[3:0, 25mV]
High Low High Low Low Low High Low N/A
Asynch Asynch Asynch Asynch Asynch BCLK TCK Asynch Asynch
Power/Other Power/Other Power/Other CMOS Output CMOS Output AGTL Output TAP Output CMOS Output Power/Other
Table 42. Input Signals (Sheet 1 of 2)
Name Active Level Clock Signal Group Qualified
A20M# BCLK BPRI# DEFER# FLUSH# IGNNE# INIT# INTR KEY
Low High Low Low Low Low Low High N/A
Asynch -- BCLK BCLK Asynch Asynch Asynch Asynch Asynch
CMOS Input System Bus Clock AGTL Input AGTL Input CMOS Input CMOS Input CMOS Input CMOS Input Power/Other
Always1 Always Always Always Always1 Always1 Always1 APIC disabled mode
80
Datasheet
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 42. Input Signals (Sheet 2 of 2)
Name Active Level Clock Signal Group Qualified
LINT[1:0] NMI NCHCTRL PICCLK PREQ# PWRGOOD RESET# RESET2# RSP# RTTCTRL SLEWCTRL SLP# SMI# STPCLK# TCK TDI TMS TRST# VTT_PWRGD
High High N/A High Low High Low Low Low N/A N/A Low Low Low High High High Low High
Asynch Asynch Asynch -- Asynch Asynch BCLK BCLK BCLK Asynch Asynch Asynch Asynch Asynch -- TCK TCK Asynch Asynch
CMOS Input CMOS Input Power/Other APIC Clock CMOS Input CMOS Input AGTL Input AGTL Input AGTL Input Power/Other Power/Other CMOS Input CMOS Input CMOS Input TAP Input TAP Input TAP Input TAP Input Power/Other
APIC enabled mode APIC disabled mode
Always Always Always Always
Always
During Stop-Grant state
NOTE: Synchronous assertion with active TDRY# ensures synchronization.
Table 43. Input/Output Signals (Single Driver)
Name Active Level Clock Signal Group Qualified
A[35:3]# ADS# AP[1:0]# BP[3:2]# BPM[1:0]# BR0# D[63:0]# DBSY# DEP[7:0]# DRDY# LOCK# REQ[4:0]# RP# RS[2:0]# TRDY#
Low Low Low Low Low Low Low Low Low Low Low Low Low Low Low
BCLK BCLK BCLK BCLK BCLK BCLK BCLK BCLK BCLK BCLK BCLK BCLK BCLK BCLK BCLK
AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL Input AGTL Input
ADS#, ADS#+1 Always ADS#, ADS#+1 Always Always Always DRDY# Always DRDY# Always Always ADS#, ADS#+1 ADS#, ADS#+1 Always
Datasheet
81
Intel(R) Celeron(R) Processor for PGA370 up to 1.40 GHz on 0.13 Process
Table 44. Input/Output Signals (Multiple Driver)
Name Active Level Clock Signal Group Qualified
AERR# BERR# BINIT# BNR# HIT# HITM# PICD[1:0]
Low Low Low Low Low Low High
BCLK BCLK BCLK BCLK BCLK BCLK PICCLK
AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O AGTL I/O APIC I/O
ADS#+3 Always Always Always Always Always Always
82
Datasheet

▲Up To Search▲

Price & Availability of RK80530RY009256

	To Download RK80530RY009256 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .