View LQ150X1LGN2A_469775.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

RECORDS OF REVISION
LQ150X1LGN2A SPEC No. DATE
REVISED
SUMMARY PAGE
NOTE
No. LD-16Z09 Jan.25.2005
1st Issue
LD-16Z09-1 1. Application This specification applies to the color 15.0 XGA TFT-LCD module LQ150X1LGN2A.
This specification are the proprietary product of SHARP CORPORATION("SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP.
The device listed in this technical literature was designed and manufactured for use in OA equipment.
In case of using the device for applications such as control and safety equipment for transportation(aircraft, trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken.
Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment for life support.
SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets.
Contact and consult with a SHARP sales representative for any questions about this device.
2.
Overview (Thin Film Transistor).
This module is a color active matrix LCD module incorporating amorphous silicon TFT
It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit. Graphics and texts can be displayed on a 1024 RGB 768 dots panel with about 16 million colors by using
LVDS (Low Voltage Differential Signaling) and supplying +3.3V DC supply voltages for TFT-LCD panel driving and supply voltage for backlight.
LD-16Z09-2 3. Mechanical Specifications Parameter Display size Specifications 38 (Diagonal) 15.0 (Diagonal) Active area Pixel format 304.1 (H) 1024 (H) (1 pixel Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment 0.297 (H) 228.1 (V) 768 (V) R+G+B dots) 0.297 (V) mm Unit cm Inch mm Pixel
R, G, B vertical stripe Normally white 326.0(W) 1100 252.0(H) 11.5(D) mm g
(MAX)
Anti-glare and hard-coating 2H (Haze value = 28)
*1.Note: excluding back light cables, cover and pet sheet. The thickness of module (D) doesn't contain the projection. Outline dimensions are shown in Fig.1.
LD-16Z09-3 4. Input Terminals
4-1. TFT-LCD panel driving CN1 (Interface signals and +3.3V DC power supply) Using connectors DF14H-20P-1.25H (Hirose Electric Co., Ltd.) Corresponding connectors DF14-20S-1.25C(Connector) DF14-2628SCFA(Terminal) Corresponding LVDS Transmitter THC63LVDM83R(Thine) or compatible
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Symbol Vcc Vcc GND GND RXIN0RXIN0+ GND RXIN1RXIN1+ GND RXIN2RXIN2+ GND RXCKINRXCKIN+ GND RXIN3RXIN3+ GND LVDS_SET
Function +3.3V Power supply +3.3V Power supply
Remark
Receiver signal (-) Receiver signal (+) Receiver signal (-) Receiver signal (+) Receiver signal (-) Receiver signal (+) Clock signal (-) Clock signal (+) Receiver signal (-) Receiver signal (+) LVDS_SET
LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS note1
LD-16Z09-4 4-2 Data Mapping 1) 8 bit input note1 pin assignment with LVDS_SET pin (Thine:THC63LVDM83R) Transmitter Pin No 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 50 2 8 10 16 18 25 Data TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 TD0 TD1 TD2 TD3 TD4 TD5 TD6 20pin =L (GND) or Open R2 R3 R4 R5 R6 R7 (MSB) G2 G3 G4 G5 G6 G7 (MSB) B2 B3 B4 B5 B6 B7 (MSB) (NA) (NA) DE R0 (LSB) R1 G0 (LSB) G1 B0 (LSB) B1 (NA) LVDS_SET =H (3.3V) R0 (LSB) R1 R2 R3 R4 R5 G0 (LSB) G1 G2 G3 G4 G5 B0 (LSB) B1 B2 B3 B4 B5 (NA) (NA) DE R6 R7 (MSB) G6 G7 (MSB) B6 B7 (MSB) (NA)
LD-16Z09-5 1 cycle RxCKIN+ RxCKIN-
RXIN0+ RXIN0-
RXIN1+ RXIN1-
RXIN2+ RXIN2RXIN3+ RXIN3DE : Display Enable NA : Not Available
1 cycle RxCXIN+ RxCXIN-
RxIN0+ RxIN0-
RxIN1+ RxIN1-
RxIN2+ RxIN2RxIN3+ RxIN3DE : Display Enable NA : Not Available
LD-16Z09-6 2) 6 bit input note1 pin assignment with LVDS_SET pin (Thine:THC63LVDM83R) Transmitter Pin No 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 50 2 8 10 16 18 25 Data TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 TD0 TD1 TD2 TD3 TD4 TD5 TD6 1 cycle RXCKIN+ RXCKIN20pin =L (GND) or Open R0 (LSB) R1 R2 R3 R4 R5 (MSB) G0 (LSB) G1 G2 G3 G4 G5 (MSB) B0 (LSB) B1 B2 B3 B4 B5 (MSB) (NA) (NA) DE GND GND GND GND GND GND (NA) LVDS_SET =H (3.3V)
RXIN0+ RXIN0-
RXIN1+ RXIN1-
RXIN2+ RXIN2DE : Display Enable NA : Not Available In case of supplying 6 bit signal, it is recommended to connect pin No.17(Rx3-) with VCC(3.3V), and No.18(Rx3+) with GND(0V).
(Computer
)
(TFT-LCD side)
Controll
R0-R5,G0 G1-G5,B0,B1 B2-B5, NA,NA,DE R6,R7,G6,G7, B6,B7,NA
7 7 7 7 TA 0 - 6 TB 0 - 6 TC 0 - 6 TD 0 - 6
THC63LVDM83R
RX0+(6) TTL PARALLEL-TO-LVDS RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) CK+(15)
Single LVDS interface contained in a control RA 0 - 6 LVDS-TO-PARALLEL TTL RB 0 - 6 RC 0 - 6
CK
C K IN
PLL
K-(14)
PLL
CK OUT
Controll
R2-R7,G2 G3-G7,B2,B3 B4-B7, NA,NA,DE R0,R1,G0,G1, B0,B1,NA
7 7 7 7 TA 0 - 6 TB 0 - 6 TC 0 - 6 TD 0 - 6
THC63LVDM83R
RX0+(6) TTL PARALLEL-TO-LVDS RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) CK+(15)
Single LVDS interface contained in a control IC RA 0 - 6 LVDS-TO-PARALLEL TTL RB 0 - 6 RC 0 - 6
CK
C K IN
PLL
K-(14)
PLL
CK OUT
Controll
R0-R5,G0 G1-G5,B0,B1 B2-B5, NA,NA,DE GND 6,NA
7 7 7 7 TA 0 - 6 TB 0 - 6 TC 0 - 6 TD 0 - 6
THC63LVDM83R
RX0+(6) TTL PARALLEL-TO-LVDS RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) CK+(15)
Single LVDS interface contained in a control IC RA 0 - 6 LVDS-TO-PARALLEL TTL RB 0 - 6 RC 0 - 6
CK
C K IN
PLL
K-(14)
PLL
CK OUT
Internal circuits
RD 0 - 6
Internal circuits
RD 0 - 6
Internal circuits
RD 0 - 6
LD-16Z09-8 4-4 Backlight CN 2, 3 The module-side connector The user-side connector Pin no. 1 2 symbol
HIGH LOW
BHSR-02VS-1
(JST) (JST)
SM02B-BHSS-1-TB Function Power supply for lamp Power supply for lamp
I/O I I
(High voltage side) (Low voltage side)
CN2 CN3
5.
Absolute Maximum Ratings Parameter Supply voltage Lamp Input voltage Storage temperature Operating temperature Note1 Humidity Symbol Vcc VHIGH TSTG TOPA ( Ta Panel surface 40 ) or less. ( Ta>40 ) Condition Ta=25 0 25 0 Ratings 0 + 4.0 + 2700 + 60 + 60 rms Note1 Unit Remark
95%RH Max.
Maximum wet-bulb temperature at 39 No condensation.
LD-16Z09-9 6. Electrical Characteristics 6-1. TFT-LCD panel driving Parameter Vcc Supply voltage Current dissipation Permissive input ripple voltage Differential input threshold voltage Input current (High) Input current (Low) Terminal resistor Note1 High Low Symbol Vcc Icc VRF VTH VTL IOH IOL RT 100 -100 10 10 Min. +3.0 Typ. +3.3 425 Max. +3.6 700 100 +100 Unit V mA mVp-p mV mV A A Ta 25 Remark Note2 Note3 Vcc=+3.3V VCM=+1.2V Note1 VI=2.4V, Vcc=3.6V VI=0V, Vcc=3.6V Differential input
VCM : Common mode voltage of LVDS driver.
0.9Vcc
0.9Vcc
Note2 1 On-off sequences of Vcc and data 0 0 0 1s t1 t2 t3 t4 10ms 10ms 1s
Vcc
0.1Vcc
0.1Vcc
0.1Vcc
data
t1
t2
t3
ON OFF
t4
t5
Back light
OFF
200ms t5 Power sequence for Backlight is not especially specified, however it is recommended to consider some timing difference between LVDS input and Backlight input as shown above. If the Backlight lights on before LCD starting, or if the Backlight is kept on after LCD stopping, the screen may look white for a moment or abnormal image may be displayed. This is caused by variation in output signal from timing generator at LVDS input on or off. It does not cause the damage to the LCD module.
2
Dip conditions for supply voltage 1) td 2) V2 Vcc 10ms V2 V1
V1 : 3.0V V2 : 2.5V V2 V1
Vcc
Vcc-dip conditions should also follow the on-off conditions.
Note3
Typical current situation : 16-gray-bar pattern
Vcc=+3.3V, CK=65MHz Horizontal period =20.7 us Gray scale : GS(4n) n=0 15 below section 8-2.
The explanation of each gray scale, GS(4n), is described
LD-16Z09-10 6-2. Backlight The back light system is an edge-lighting type with 2 CCFTs (Cold Cathode Fluorescent Tube). The characteristics of the lamp are shown in the following table. The value mentioned below is at the case of one CCFT. CCFT Model Name : KTBE24MSTF-530.5KB270-Z-L (STANLEY ELECTRIC CO.,LTD) Parameter Symbol Min. Typ. Max. Unit Remark Lamp current range IL 3.0 4.0 5.0 mArms Note1 1050 1200 Vrms Lamp voltage VL IL=4.0 mArms Ta=25 Lamp power consumption PL 4.2 4.8 W Note2 IL=4.0 mArms Ta=25 Lamp frequency FL 40 60 70 kHz Note3 Kick-off voltage Vs 2200 Vrms Ta=0 60kHz Note4 Lamp life time TL 50,000 hour Note5 Note1
60kHz 60kHz
A lamp can be light in the range of lamp current shown above. Maximum rating for current is measured by high frequency current measurement equipment connected to VLOW at circuit showed below. (Note : To keep enough kick-off voltage and necessary steady voltage for CCFT.) Lamp frequency : 40 70kHz Ambient temperature : 0 50
Note2
Referential data per one CCFT by calculation ( IL The data don't include loss at inverter.
VL ) .
Note3
Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. Therefore, adjust lamp frequency, and keep inverter as far as from module or use electronic shielding between inverter and module to avoid interference. This is transformer output voltage at 33pF for the ballast capacitor of a DC-AC inverter. The kick-off voltage may rise up in the user set, please decide the open output voltage by checking not to occur lighting failure under operating state. The open output voltage should be applied to the lamp for more than 1 second to startup. Otherwise the lamp may not be turned on. ballast capacitor(33pF)
Module 1
V
Note4
Inverter
2
2pin VLOW
Note5
LD-16Z09-11 Lamp life time is defined as the time when either or occurs in the continuous operation under the condition of Ta=25 and IL=4.0 mA rms. Brightness becomes 50% of the original value under standard condition. Kick-off voltage at Ta=0 exceeds 2200 Vrms value.
Note The performance of the backlight, for example lifetime or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. When you confirm it, the module should be operated in the same condition as it is installed in your instrument. Use the lamp inverter power source incorporating such safeguard as overvoltage / overcurrent protective circuit or lamp voltage waveform detection circuit, which should have individual control of each lamp. In case one circuit without such individual control is connected to more than two lamps, excessive current may flow into one lamp when the other one is not in operation. 7. Timing characteristics of input signals 7-1. Timing characteristics
Parameter Clock signal ENAB signal Frequency Horizontal period
Symbol 1/Tc TH
Min. 50.0 1056 16.0
Typ. 65.0 1344 20.7 1024 806 768
Max. 80.0 1720 23.4 1024 990 768
Unit MHz clock s clock line line
Horizontal period (High) Vertical period Vertical period (High) Note
THd TV TVd
1024 773 768
In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.
DE DATA (R,G,B)
DE
LD-16Z09-12 7-2 Input Data Signals and Display Position on the screen
R1 G1 B1 R2 G2 B2
RGB
LD-16Z09-13 8. Input Signals, Basic Display Colors and Gray Scale of Each Color 8-1 8bit input
Data signal
Colors & Gray
R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7
Gray scale Scale Black Blue Green Cyan Red Magenta Yellow White Black GS0 GS1 Darker GS2 0 0 0 0 X X X X 0 1 0 0 0 0 0 X X X X 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 X X 0 0 X X 0 0 0 0 0 X X 0 0 X X 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 X 0 X 0 X 0 X 0 0 0 0 X 0 X 0 X 0 X 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0
0 : Low level voltage,
total 24 bit data signals, the 16-million-color display can be achieved on the screen.
Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue
Brighter
GS250 GS251
0 1 X 0 0 0
1 1 X 0 0 0
0 0 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Red Black
GS252 GS0 GS1
Darker
GS2
Brighter
GS250 GS251
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 1 X 0 0 0
1 1 X 0 0 0
0 0 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Green Black
GS252 GS0 GS1
Darker
GS2
Brighter
GS250 GS251
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 1 X
1 1 X
0 0 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
Blue
GS252
1 : High level voltage.
X :Don't care.
Each basic color can be displayed in 253 gray scales from 8 bit data signals. According to the combination of
LD-16Z09-14 8-2 6bit input
Data signal
Colors & Gray scale Black Blue Green Cyan Red Magenta Yellow White Black GS0 GS1 Gray Scale
R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
0 0 0 0 1 1 1 1 0 1 0
0 0 0 0 1 1 1 1 0 0 1
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 : Low level voltage,
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen.
Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue
Darker
GS2
Brighter
GS61 GS62
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Red Black
GS63 GS0 GS1
Darker
GS2
Brighter
GS61 GS62
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Green Black
GS63 GS0 GS1
Darker
GS2
Brighter
GS61 GS62
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
1 0 1
0 1 1
0 1 1
1 1 1
1 1 1
1 1 1
Blue
GS63
1 : High level voltage.
LD-16Z09-15 9. Optical Characteristics Ta=25 Parameter
Viewing angle
Vertical
, Vcc =+3.3V Remark
Note1,4
Symbol 11 12
Condition CR 5
Min. 40 70
Typ. 55 80 80 45 55 60 350 5 20
Max.
Unit Deg. Deg. Deg. Deg. Deg. Deg.
range
Horizontal Vertical
21, 11 12
22 CR 10
70 30 45
Horizontal
21,
22 =0 r d
50 250
Contrast ratio Response Time Rise Fall x y x y x y x y YL
Note2,4
20 40 0.343 0.359 0.611 0.352 0.337 0.576 0.181 0.157
ms ms
Note3,4
Chromaticity of White Chromaticity of Red Chromaticity of Green Chromaticity of Blue
Luminance of white
0.283 0.299 0.551 0.292 0.277 =0 0.516 0.121 0.097 200
0.313 0.329 0.581 0.322 0.307 0.546 0.151 0.127 260
Note4
cd/m2
IL=4.0mA rms fL=60kHz Note4
White Uniformity
w
1.25
Note5
The measurement shall be executed 30 minutes after lighting at rating.
The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig.2 below.
LD-16Z09-16 Note1 Definitions of viewing angle range:
' Note2 Definition of contrast ratio: The contrast ratio is defined as the following.
Luminance (brightness) with all pixels white
Contrast Ratio (CR)
Luminance (brightness) with all pixels black
Note3
Definition of response time: The response time is defined as the following figure and shall be measured by switching the input
signal for "black" and "white".
Note4 Note5
This shall be measured at center of the screen. Definition of white uniformity: White uniformity is defined as the following with five measurements
256 512 768 pixel
(A
E).
A
D
192 384
Maximum Luminance of five points (brightness) Minimum Luminance of five points (brightness)
C
B
E
576 pixel
LD-16Z09-17 10. Handling Precautions a) b) Be sure to turn off the power supply when inserting or disconnecting the cable. Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) d) e) f) Since the front polarize is easily damaged, pay attention not to scratch it. Since long contact with water may cause discoloration or spots, wipe off water drop immediately. When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care. g) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into consideration when handling. h) Make sure the four mounting holes of the module are grounded sufficiently. Take electro-magnetic interference (EMI) into consideration. i) The module has some printed circuit boards (PCBs) on the back side. Take care to keep them form any stress or pressure when handling or installing the module; otherwise some of electronic parts on the PCBs may be damaged. j) k) Observe all other precautionary requirements in handling components. When some pressure is added onto the module from rear side constantly, it causes display non-uniformity issue, functional defect, etc. So, please avoid such design. l) When handling LCD modules and assembling them into cabinets, please be noted that long-term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules.
11. Packing form a) Production country : JAPAN , TAIWAN, CHINA maximum 6 cartons 10 modules 398mm(D) 12.0kg(typ.)
b) Piling number of cartons :
c) Packing quantity in one carton : d) Carton size : 408mm(W)
340mm(H)
e) total mass of one carton filled with full modules : f) Packing form is shown in Fig.3
LD-16Z09-18 12 No 1 2 3 4 5 6 Reliability test items Test item High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Vibration test (non- operating) Conditions Ta = 60 Ta = -25 Ta = 40 Ta = 60 Ta = 0 Frequency : 10 : 58 240h 240h ; 95%RH 240h ) 240H 57Hz/Vibration width (one side) : 0.075mm 500Hz/Gravity : 9.8m/s2 240h
(No condensation) (The temperature Waveform : Sine wave
Sweep time : 11minutes Test period : 3 hours (1 hour for each direction of X,Y,Z) 7 Shock test (non- operating) Max. gravity : 490m/s2 Pulse width : 11ms, sine wave Direction : 8 9 Thermal shock test (Storage) Altitude Result Evaluation Criteria Under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function. Ta=-25 Ta=50 Ta=70 X, 60 Y, Z, once for each direction. ; 5 cycles (Operating) (Storage) Test period : 10 hours (1 hour for each temperature) ,70kPa,3,048m(10,000ft), t=24h ,12kPa,15,240m(50,000ft), t=24h
LD-16Z09-19 13 Others 1) Lot No. and indication Bar Code Label: Production country
Japan Taiwan China MADE IN JAPAN MADE IN TAIWAN MADE IN CHINA
2) Packing Label
LQ150X1LGN2A
Bar code
Bar code Bar code
Model No. (LQ150X1LGN2A) Lot No. (Date) Quantity
3) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may not be satisfied. 4) Disassembling the module can cause permanent damage and should be strictly avoided. 5) Please be careful since image retention may occur when a fixed pattern is displayed for a long time. 6) The chemical compound which causes the destruction of ozone layer is not being used. 7) Warning of mercury and material information of LPG (Light Pipe Guide) are printed on the back of the module. MATERIAL INFORMATION >PLASTIC LIGHT GUIDE:PMMA< 8)Cold cathode fluorescent lamp in LCD PANEL contains a small amount of mercury, Please follow local ordinances or regulations for disposal.
COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS A SMALL AMOUNT OF MERCURY, PLEASE FOLLOW LOCAL ORDINANCES OR REGULATION FOR DISPOSAL
9) This specification document's Japanese language version is also available. Its Number (SPEC. No.) is LD-15712B. 10) When any question or issue occurs, it shall be solved by mutual discussion.
LD-16Z09-20 14. Carton storage condition Temperature Humidity 0 to 40
95%RH or less 20 5 to 35 to 15 , 85%RH or less , 85%RH or less (summer) (winter)
Reference condition : :
the total storage time (40 Sunlight Atmosphere
,95%RH) : 240H or less
Be sure to shelter a product from the direct sunlight. Harmful gas, such as acid and alkali which bites electronic components and/or wires must not be detected.
Notes
Be sure to put cartons on palette or base, don't put it on floor, and store them with removing from wall Please take care of ventilation in storehouse and around cartons, and control changing temperature is within limits of natural environment
Storage period
1 year

▲Up To Search▲

Price & Availability of LQ150X1LGN2A

	To Download LQ150X1LGN2A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .