 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Product Information TA G - 1 0 3 5 5.8 to 6.4 GHz GaAs MMIC V S AT (C-BAND) Power Amplifier AT F e a t u re s re 26 dBm Minimum Linear Output Power 18 dB Small Signal Gain Thermally Efficient Moly-Copper Package C-Band VSAT Application ISO 9001 CERTIFIED Product Description The TAG-1035 amplifier is ideally suited to provide linear power amplification for C-Band VSAT satellite applications. Typical uses are as a driver amplifier for VSAT power modules and C-Band SATCOM transmitters. The amplifier provides a minimum of +26 dBm linear power output. Typical DC power consumption is 600 mA at +7.0V and 10 mA at -1.0V. , Electrical Specifications (All Specifications at 25oC, Vd = +7.0V Id = 600 mA) P a ra m e te r S m all S ignal G ain Input Return Los s Revers e Is olation O utput P ower @ 1dB G ain Com pres s ion Tem perature Coeffic ient of Gain S ym bol Fre que ncy 5.8 to 6.4 G Hz S 21 S 11 S 12 P -1dB S 21 5.8 to 6.4 G Hz 5.8 to 6.4 G Hz 5.8 GHz 6.1 GHz 6.4 GHz 5.8 to 6.4 G Hz M in 18 30 26 28 28 Max Typica l 23 -10 48 27.5 29.2 29.2 -0.045 Units dB dB dB dB m dB m dB m dB / o C Typical Small Signal Gain and Input Return Loss 30 20 10 0 -10 -20 -30 5.80 32 31 30 29 28 27 26 25 24 5.80 Gain / Return Loss (dB) Typical Output Power Gain Return 5.90 6.00 6.10 6.20 Frequency (GHz) 6.30 6.40 Output Power (dBm) P-1dB Psat 5.90 6.00 6.10 6.20 6.30 Frequency (GHz) 6.40 6.50 www.teledynewireless.com email: amplifiers@teledyne.com 10/2001 1274 Terra Bella Avenue, Mountain View, CA 94043 * Tel: 800-832-6869 * Fax: (650) 962-6845 13 TAG-1035 VSAT 5.8 to 6.4 GHz GaAs MMIC Power Amplifier for VSAT (C-Band) Applications Package Outline Pin 3: RF Input Pin 5: Vg Pin 8: RF Output Pin 10:Vd T ypical Biasing Configuration 10 PACKAGED AMPLIFIER 470 pF Vd Bypass (1F Typical) 8 RF Output (50 ohms) PIN 1 10 3 8 RF Input (50 ohms) Input 3 GaAs MMIC 470 pF 5 PIN 6 Vg Bypass (1F Typical) 5 Tolerance: .XXX 0.005 External Components Required: Bypass Capacitors: 1 F, typical 50 Ohm microsrtip interface Evaluation Circuit Evaluation Board GND GND 1 2 3 10 Vdd C2 1.0 f GND 9 8 7 6 GND GND 1.0 f GND TAG-1035 RF IN 50 OHM LINE 4 5 GND 50 OHM LINE RF OUT C1 GND V6 Notes 1. Dual bias supply required. 2. 3. 4. 5. 6. 7. 8. 9. DC supply sequencing or protection circuitry not included. See Amplifier Biasing Procedure A 360 pF DC supply line decoupling capacitor is included on both Vd and Vg lines. (See typical biasing configuration shown above). The last fixture or circuit should incorporate additional bypass capacity (25ufd) on the drain and gate bias terminals to prevent oscillations caused by feedback signals. Supply (drain and gate) wire/leads should be as short as possible. Close placement of external components to the power amplifier is essential for stability purposes. TET recommends the unit be soldered to DC and RF ground for best results. Pin numbers indicated on outline drawing are for user information only. Units are not labeled with pin numbers. MASK drawing for circuit board available on the Teledyne Wireless website at www.teledynewireless.com. Teledyne reserves the right to make changes without further notice to any specification herein. "Typical" parameters can and do vary. www.teledynewireless.com email: amplifiers@teledyne.com 10/2001 1274 Terra Bella Avenue, Mountain View, CA 94043 * Tel: 800-832-6869 * Fax: (650) 962-6845 14 |
Price & Availability of TAG-1035
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |