 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TC58V64DC TENTATIVE TOSHIBA MOS DIGITAL INTEGRATED CIRCUIT SILICON GATE CMOS 64-MBIT (8M x 8 BITS) CMOS NAND E PROM (8M BYTE SmartMedia DESCRIPTION 2 TM ) The TC58V64 is a single 3.3-V 64-Mbit (69,206,016) bit NAND Electrically Erasable and Programmable Read-Only Memory (NAND E2PROM) organized as 528 bytes x 16 pages x 1024 blocks. The device has a 528-byte static register which allows program and read data to be transferred between the register and the memory cell array in 528-byte increments. The Erase operation is implemented in a single block unit (8 Kbytes + 512 bytes: 528 bytes x 16 pages). The TC58V64 is a serial-type memory device which utilizes the I/O pins for both address and data input/output as well as for command inputs. The Erase and Program operations are automatically executed making the device most suitable for applications such as solid-state file storage, voice recording, image file memory for still cameras and other systems which require high-density non-volatile memory data storage. The data stored in the TC58V64DC needs to comply with the data format standardized by the SSFDC Forum in order to maintain compatibility with other SmartMediaTM systems. FEATURES * Organization Memory cell array 528 x 16K x 8 Register 528 x 8 Page size 528 bytes Block size (8K + 512) bytes Modes Read, Reset, Auto Page Program, Auto Block Erase, Status Read Mode control Serial input/output, Command control Complies with the SmartMediaTM Electrical Specification and Data Format Specification issued by the SSFDC Forum * * * Power supply VCC = 3.3 V 0.3 V Access time Cell array-register 7 s max Serial Read cycle 50 ns min Operating current Read (50-ns cycle) 10 mA typ. Program (avg.) 10 mA typ. Erase (avg.) 10 mA typ. Standby 100 A max Package TC58V64DC: FDC-22A (Weight: 1.8 g typ.) * * * * PIN ASSIGNMENT (TOP VIEW) VSS CLE ALE PIN NAMES I/O4 VSS VSS WE WP I/O1 I/O2 I/O3 I/O1~I/O8 CE I/O port Chip enable Write enable Read enable Command latch enable Address latch enable Write protect Ready/Busy Ground Input Low Voltage Detect Power supply Ground TM WE RE CLE ALE WP 1 2 3 4 5 6 7 8 9 10 11 RY/BY GND LVD 22 21 20 19 18 17 16 15 14 13 12 VCC VSS VCC CE RE RY/BY GND LVD I/O8 I/O7 I/O6 I/O5 VCC is a trademark of Toshiba Corporation. 000707EBA2 * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. 2000-08-27 1/33 TC58V64DC BLOCK DIAGRAM VCC VSS Status register I/O1 I/O control circuit ~ I/O8 CE Address register Column buffer Column decoder Command register Data register Sense amp ROW address decoder ROW address buffer decoder CLE ALE Logic control WE RE WP RY/BY RY/BY HV generator Control circuit Memory cell array ABSOLUTE MAXIMUM RATINGS SYMBOL VCC VIN VI/O PD Tstg Topr PARAMETER Power Supply Voltage Input Voltage Input/Output Voltage Power Dissipation Storage Temperature Operating Temperature RATING -0.6~4.6 -0.6~4.6 -0.6 V~VCC + 0.3 V ( 4.6 V) 0.3 -20~65 0~55 UNIT V V V W C C CAPACITANCE *(Ta = 25C, f = 1 MHz) SYMBOL CIN COUT Input Output PARAMETER CONDITION VIN = 0 V VOUT = 0 V MIN MAX 10 10 UNIT pF pF * This parameter is periodically sampled and is not tested for every device. 000707EBA2 * The products described in this document are subject to the foreign exchange and foreign trade laws. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. * The information contained herein is subject to change without notice. 2000-08-27 2/33 TC58V64DC VALID BLOCKS (1) SYMBOL NVB PARAMETER Number of Valid Blocks MIN 1014 TYP. MAX 1024 UNIT Blocks (1) The TC58V64 occasionally contains unusable blocks. Refer to Application Note 14 toward the end of this document. RECOMMENDED DC OPERATING CONDITIONS SYMBOL VCC VIH VIL * PARAMETER Power Supply Voltage High Level Input Voltage Low Level Input Voltage -2 V (pulse width 20 ns) MIN 3 2 -0.3* TYP. 3.3 MAX 3.6 VCC + 0.3 0.8 UNIT V V V DC CHARACTERISTICS (Ta = 0~55C, VCC = 3.3 V 0.3 V) SYMBOL IIL ILO ICCO1 ICCO3 ICCO4 ICCO5 ICCO7 ICCO8 ICCS1 ICCS2 VOH VOL IOL ( RY/BY ) PARAMETER Input Leakage Current Output Leakage Current Operating Current (Serial Read) Operating Current (Command Input) Operating Current (Data Input) Operating Current (Address Input) Programming Current Erasing Current Standby Current Standby Current High Level Output Voltage Low Level Output Voltage Output Current of RY/BY Pin CE = VIH CE = VCC - 0.2 V CONDITION VIN = 0 V~VCC VOUT = 0.4 V~VCC CE = VIL, IOUT = 0 mA, tcycle = 50 ns MIN TYP. 10 MAX 10 10 30 UNIT A A mA tcycle = 50 ns tcycle = 50 ns tcycle = 50 ns 10 10 10 10 10 8 30 30 30 30 30 1 100 0.4 mA mA mA mA mA mA A V V mA 2.4 IOH = -400 A IOL = 2.1 mA VOL = 0.4 V 2000-08-27 3/33 TC58V64DC AC CHARACTERISTICS AND OPERATING CONDITIONS (Ta = 0~55C, VCC = 3.3 V 0.3 V) SYMBOL tCLS tCLH tCS tCH tWP tALS tALH tDS tDH tWC tWH tWW tRR tRP tRC tREA tCEH tREAID tOH tRHZ tCHZ tREH tIR tRSTO tCSTO tRHW tWHC tWHR tAR1 tCR tR tWB tAR2 tRB tCRY tRST CLE Setup Time CLE Hold Time CE Setup Time CE Hold Time Write Pulse Width ALE Setup Time ALE Hold Time Data Setup Time Data Hold Time Write Cycle Time PARAMETER MIN 0 10 0 10 25 0 10 20 10 50 15 100 20 35 50 100 10 15 0 0 30 30 100 100 50 MAX 35 35 30 20 35 45 7 100 100 50 + tr ( RY/BY ) 6/10/500 UNIT ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns s ns ns ns ns s (1) (2) NOTES WE -High Hold Time WP High to WE Low Ready-to- RE Falling Edge Read Pulse Width Read Cycle Time RE Access Time (Serial Data Access) CE -High Time for Last Address in Serial Read Cycle RE Access Time (ID Read) Data Output Hold Time RE -High-to-Output-High Impedance CE -High-to-Output-High Impedance RE -High Hold Time Output-High-Impedance-to- RE Rising Edge RE Access Time (Status Read) CE Access Time (Status Read) RE High to WE Low WE High to CE Low WE High to RE Low ALE Low to RE Low (ID Read) CE Low to RE Low (ID Read) Memory Cell Array to Starting Address WE High to Busy ALE Low to RE Low (Read Cycle) RE Last Clock Rising Edge to Busy (in Sequential Read) CE High to Ready (When interrupted by CE in Read Mode) Device Reset Time (Read/Program/Erase) AC TEST CONDITIONS PARAMETER Input level Input pulse rise and fall time Input comparison level Output data comparison level Output load VALUES 2.4 V, 0.4 V 3 ns 1.5 V, 1.5 V 1.5 V, 1.5 V CL (100 pF) + 1 TTL 2000-08-27 4/33 TC58V64DC Notes: (1) CE High to Ready time depends on the pull-up resistor tied to the RY/ BY pin. (Refer to Application Note (7) toward the end of this document.) (2) Sequential Read is terminated when tCEH is greater than or equal to 100 ns. If the RE to CE delay is less than 30 ns, RY/ BY signal stays Ready. tCEH 100 ns * CE *: VIH or VIL RE 525 526 527 A A : 0~30 ns Busy signal is not output. RY/BY Busy PROGRAMMING AND ERASING CHARACTERISTICS (Ta = 0~55C, VCC = 3.3 V 0.3 V) SYMBOL tPROG N tBERASE P/E PARAMETER Programming Time Number of Programming Cycles on Same Page Block Erasing Time Number of Program/Erase Cycles MIN TYP. 200 2 MAX 1000 10 20 1 x 106 ms (2) UNIT s (1) NOTES (1) Refer to Application Note 12 toward the end of this document. (2) Refer to Application Note 15 toward the end of this document. 2000-08-27 5/33 TC58V64DC TIMING DIAGRAMS Latch Timing Diagram for Command/Address/Data CLE ALE CE RE Setup Time Hold Time WE tDS I/O1 ~I/O8 tDH : VIH or VIL Command Input Cycle Timing Diagram CLE tCLS tCS tCLH tCH CE tWP WE tALS tALH ALE tDS I/O1 ~I/O8 tDH : VIH or VIL 2000-08-27 6/33 TC58V64DC Address Input Cycle Timing Diagram tCLS CLE tCS tWC tWC CE tWP tWH tWP tWH tWP WE tALS tALH ALE tDS I/O1 ~I/O8 tDH tDS tDH tDS tDH A0~A7 A9~A16 A17~A22 : VIH or VIL Data Input Cycle Timing Diagram tCLH CLE tCH CE tALS tWC ALE tWP tWH tWP tWP WE tDS I/O1 ~I/O8 tDH tDS tDH tDS tDH DIN0 DIN1 DIN 527 : VIH or VIL 2000-08-27 7/33 TC58V64DC Serial Read Cycle Timing Diagram tRC CE tRP tREH tRP tRP tCHZ RE tREA I/O1 ~I/O8 tRR tOH tRHZ tREA tOH tRHZ tREA tOH tRHZ RY/BY Status Read Cycle Timing Diagram tCLS CLE tCLS tCS tCLH CE tWP tCH WE tWHC tWHR tCSTO tCHZ RE tDS I/O1 ~I/O8 tDH tIR tRSTO tOH tRHZ 70H* Status output RY/BY * 70H represents the hexadecimal number 70. : VIH or VIL 2000-08-27 8/33 TC58V64DC Read Cycle (1) Timing Diagram CLE tCLS tCS tCLH tCH tCEH CE tWC tCRY WE tALH tALS tALH tAR2 ALE tR tWB tDS tDH I/O1 ~I/O8 tDS tDH tDS tDH tDS tDH tREA DOUT N DOUT N+1 DOUT N+2 DOUT 527 tRB tRR tRC RE 00H A0~A7 Column address N* A9~A16 A17~A22 RY/BY : VIH or VIL Read Cycle (1) Timing Diagram: When Interrupted by CE CLE tCLS tCS tCLH tCH CE tWC tCHZ WE tALH tALS tALH tAR2 ALE tR tWB tDS tDH I/O1 ~I/O8 tDS tDH tDS tDH tDS tDH tREA DOUT N DOUT N+1 tRR tRC RE tOH tRHZ DOUT N+2 00H A0~A7 Column address N* A9~A16 A17~A22 RY/BY * Read Operation using 00H Command N: 0~255 : VIH or VIL 2000-08-27 9/33 TC58V64DC Read Cycle (2) Timing Diagram CLE tCLS tCS tCLH tCH CE WE tALH tALS tALH tAR2 ALE tR tWB tDS tDH I/O1 ~I/O8 tDS tDH tREA tRR tRC RE 01H A0~A7 A9~A16 A17~A22 Column address N* DOUT DOUT DOUT 527 256 + M 256 + M + 1 RY/BY * Read Operation using 01H Command N: 0~255 : VIH or VIL Read Cycle (3) Timing Diagram CLE tCLS tCS tCLH tCH CE WE tALH tALS tALH tAR2 ALE tR tWB tDS tDH I/O1 ~I/O8 tDS tDH tREA tRR tRC RE 50H A0~A7 A9~A16 A17~A22 Column address N* DOUT DOUT DOUT 527 512 + M 512 + M + 1 RY/BY * Read Operation using 50H Command N: 0~15 : VIH or VIL 2000-08-27 10/33 TC58V64DC Sequential Read (1) Timing Diagram CLE CE WE ALE RE I/O1 ~I/O8 00H A0~A7 A9~A16 A17~A22 Page Column address address M N tR N N+1 N+2 527 tR 0 1 2 527 RY/BY Page M access Page M + 1 access : VIH or VIL Sequential Read (2) Timing Diagram CLE CE WE ALE RE I/O1 ~I/O8 01H A0~A7 A9~A16 A17~A22 Page Column address address M N tR 256 + 256 + 256 + N N+1 N+2 527 tR 0 1 2 527 RY/BY Page M access Page M + 1 access : VIH or VIL 2000-08-27 11/33 TC58V64DC Sequential Read (3) Timing Diagram CLE CE WE ALE RE I/O1 ~I/O8 50H A0~A7 A9~A16 A17~A22 Page Column address address M N tR 512 + 512 + 512 + N N+1 N+2 527 tR 512 513 514 527 RY/BY Page M access Page M + 1 access : VIH or VIL 2000-08-27 12/33 TC58V64DC Auto-Program Operation Timing Diagram tCLS CLE tCLS tCLH tCS CE tCS WE tCH tALH tALS tALH tALS tPROG tWB ALE RE tDS tDH I/O1 ~I/O8 80H tDS tDH A0~A7 A9~A16 A17~A22 tDS tDH DIN0 DIN1 DIN 527 10H tDS tDH 70H Status output RY/BY : VIH or VIL : Do not input data while data is being output. Auto Block Erase Timing Diagram CLE tCLS tCS CE tCLH tCLS WE tALS ALE tALH tWB tBERASE RE tDS tDH I/O1 ~I/O8 60H A9~A16 A17~A22 D0H 70H Status output RY/BY Auto Block Erase Setup command : VIH or VIL Erase Start command Busy Status Read command : Do not input data while data is being output. 2000-08-27 13/33 TC58V64DC ID Read Operation Timing Diagram CLE tCLS tCS tCH tCLS tCS CE tCH WE tALH tALS tALH tCR tAR1 ALE RE tDS tDH I/O1 ~I/O8 tREAID tREAID 90H 00 98H E6H Address input Maker code Device code : VIH or VIL 2000-08-27 14/33 TC58V64DC PIN FUNCTIONS The device is a serial access memory which utilizes time-sharing input of address information. The device pin-outs are configured as shown in Figure 1. TC58V64DC Command Latch Enable: CLE The CLE input signal is used to control loading of the operation mode command into the internal command register. The command is latched into the command register from the I/O port on the rising edge of the WE signal while CLE is High. 1 2 3 4 5 6 7 8 9 10 11 VSS CLE ALE WE WP I/O1 I/O2 I/O3 I/O4 VSS VSS Address Latch Enable: ALE The ALE signal is used to control loading of either address information or input data into the internal address/data register. Address information is latched on the rising edge of WE if ALE is High. Input data is latched if ALE is Low. Chip Enable: CE 22 21 20 19 18 17 16 15 14 13 12 The device goes into a low-power Standby mode when CE Figure 1. Pinout goes High during a Read operation. The CE signal is ignored when device is in Busy state ( RY/ BY = L), such as during a Program or Erase operation, and will not enter Standby mode even if the CE input goes High. The CE signal must stay Low during the Read mode Busy state to ensure that memory array data is correctly transferred to the data register. VCC CE RE RY/BY GND LVD I/O8 I/O7 I/O6 I/O5 VCC Write Enable: WE The WE signal is used to control the acquisition of data from the I/O port. Read Enable: RE The RE signal controls serial data output. Data is available tREA after the falling edge of RE . The internal column address counter is also incremented (Address = Address + 1) on this falling edge. I/O Port: I/O1~I/O8 The I/O1 to I/O8 pins are used as a port for transferring address, command and input/output data to and from the device. Write Protect: WP The WP signal is used to protect the device from accidental programming or erasing. The internal voltage regulator is reset when WP is Low. This signal is usually used for protecting the data during the power-on/off sequence when input signals are invalid. Ready/Busy: RY / BY The RY/ BY output signal is used to indicate the operating condition of the device. The RY/ BY signal is in Busy state ( RY/ BY = L) during the Program, Erase and Read operations and will return to Ready state ( RY/ BY = H) after completion of the operation. The output buffer for this signal is an open drain. Low Voltage Detect: LVD The LVD signal is used to detect the power supply voltage level. 2000-08-27 15/33 TC58V64DC Schematic Cell Layout and Address Assignment The Program operation works on page units while the Erase operation works on block units. I/O1 512 16 I/O8 A page consists of 528 bytes in which 512 bytes are used for main memory storage and 16 bytes are for redundancy or for other uses. 1 page = 528 bytes 1 block = 528 bytes x 16 pages = (8K + 512) bytes Capacity = 528 bytes x 16 pages x 1024 blocks An address is read in via the I/O port over three consecutive clock cycles, as shown in Table 1. 16 pages = 16384 pages 1024 blocks = 8I/O 528 Figure 2. Schematic Cell Layout Table 1. Addressing I/O8 First cycle Second cycle Third cycle *: *: A7 A16 *L I/O7 A6 A15 *L I/O6 A5 A14 A22 I/O5 A4 A13 A21 I/O4 A3 A12 A20 Table 2. Logic table CLE Command Input Data Input Address Input Serial Data Output During Programming (Busy) During Erasing (Busy) Program, Erase Inhibit H: VIH, L: VIL, *: VIH or VIL H L L L * * * 1 block I/O3 A2 A11 A19 I/O2 A1 A10 A18 I/O1 A0 A9 A17 A0~A7: A9~A22: A13~A22: A9~A12: Column address Page address Block address NAND address in block A8 is automatically set to Low or High by a 00H command or a 01H command. I/O7 and I/O8 must be set to Low in the third cycle. Operation Mode: Logic and Command Tables The operation modes such as Program, Erase, Read and Reset are controlled by the ten different command operations shown in Table 3. Address input, command input and data input/output are controlled by the CLE, ALE, CE , WE , RE and WP signals, as shown in Table 2. ALE L L H L * * * CE WE RE H H H WP * * * * L L L L * * * H * * * * * * H H L 2000-08-27 16/33 TC58V64DC Table 3. Command table (HEX) First Cycle Serial Data Input Read Mode (1) Read Mode (2) Read Mode (3) Reset Auto Program Auto Block Erase Status Read ID Read 80 00 01 50 FF 10 60 70 90 Second Cycle D0 1 0 0 6 0 5 0 4 0 3 0 0 Acceptable while Busy HEX data bit assignment (Example) Serial data input: 80H I/O8 7 2 I/O1 Once the device has been set to Read mode by a 00H, 01H or 50H command, additional Read commands are not needed for sequential page Read operations. Table 4 shows the operation states for Read mode. Table 4. Read mode operation states CLE Output Select Output Deselect Standby H: VIH, L: VIL, *: VIH or VIL L L L ALE L L L CE WE H H H RE L H * I/O1~I/O8 Data output High impedance High impedance Power Active Active Standby L L H 2000-08-27 17/33 TC58V64DC DEVICE OPERATION Read Mode (1) Read mode (1) is set when a 00H command is issued to the Command register. Refer to Figure 3 below for timing details and the block diagram. CLE CE WE ALE RE RY/BY M I/O 00H Start-address input M 527 A data transfer operation from the cell array to the register starts on the rising edge of WE in the third cycle (after the address information has been latched). The device will be in Busy state during this transfer period. The CE signal must stay Low after the third address input and during Busy state. After the transfer period the device returns to Ready state. Serial data can be output synchronously with the RE clock from the start pointer designated in the address input cycle. Busy N Select page N Figure 3. Read mode (1) operation Cell array Read Mode (2) CLE CE WE ALE RE RY/BY M I/O 01H Start-address input 256 M 527 The operation of the device after input of the 01H command is the same as that of Read mode (1). If the start pointer is to be set after column address 256, use Read mode (2). However, for a Sequential Read, output of the next page starts from column address 0. Busy N Select page N Figure 4. Read mode (2) operation Cell array 2000-08-27 18/33 TC58V64DC Read Mode (3) Read mode (3) has the same timing as Read modes (1) and (2) but is used to access information in the extra 16-byte redundancy area of the page. The start pointer is therefore set to a value between byte 512 and byte 527. CLE CE WE ALE RE RY/BY I/O 50H A0~A3 512 527 Addresses bits A0~A3 are used to set the start pointer for the redundant memory cells, while A4~A7 are ignored. Once a 50H command has been issued, the pointer moves to the redundant cell locations and only those 16 cells can be addressed, regardless of the value of the A4-to-A7 address. (An 00H command is necessary to move the pointer back to the 0-to-511 main memory cell location.) Busy Figure 5. Read mode (3) operation Sequential Read (1) (2) (3) This mode allows the sequential reading of pages without additional address input. 00H 01H 50H RY/BY Busy (00H) 0 527 (01H) Busy (50H) Busy 512 527 A A A Address input tR Data output tR Data output tR Sequential Read (1) Sequential Read (2) Sequential Read (3) Sequential Read modes (1) and (2) output the contents of addresses 0~527 as shown above, while Sequential Read mode (3) outputs the contents of the redundant address locations only. When the pointer reaches the last address, the device continues to output the data from this address ** on each RE clock signal. ** Column address 527 on the last page. 2000-08-27 19/33 TC58V64DC Status Read The device automatically implements the execution and verification of the Program and Erase operations. The Status Read function is used to monitor the Ready/Busy status of the device, determine the result (pass/fail) of a Program or Erase operation, and determine whether the device is in Protect mode. The device status is output via the I/O port on the RE clock after a 70H command input. The resulting information is outlined in Table 5. Table 5. Status output table STATUS I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 Pass/Fail Not Used Not Used Not Used Not Used Not Used Ready/Busy Write Protect Pass: 0 0 0 0 0 0 Ready: 1 Protect: 0 Busy: 0 Not Protected: 1 The Pass/Fail status on I/O1 is only valid when the device is in the Ready state. OUTPUT Fail: 1 An application example with multiple devices is shown in Figure 6. CE1 CE2 CE3 CEN CEN + 1 CLE ALE WE RE I/O1 ~I/O8 RY/BY Device 1 Device 2 Device 3 Device N Device N+1 RY/BY CLE ALE WE CE1 CEN Busy RE I/O 70H Status on Device 1 70H Status on Device N Figure 6. Status Read timing application example System Design Note: If the RY/ BY pin signals from multiple devices are wired together as shown in the diagram, the Status Read function can be used to determine the status of each individual device. 2000-08-27 20/33 TC58V64DC Auto Page Program The device carries out an Automatic Page Program operation when it receives a 10H Program command after the address and data have been input. The sequence of command, address and data input is shown below. (Refer to the detailed timing chart.) Pass 80 Data input Address command input 10 Data input Program 0~527 command 70 Status Read command I/O Fail RY/BY Data input Program Selected page Reading & verification RY/BY automatically returns to Ready after completion of the operation. Figure 7. Auto Page Program operation The data is transferred (programmed) from the register to the selected page on the rising edge of WE following input of the 10H command. After programming, the programmed data is transferred back to the register to be automatically verified by the device. If the programming does not succeed, the Program/Verify operation is repeated by the device until success is achieved or until the maximum loop number set in the device is reached. Auto Block Erase The Auto Block Erase operation starts on the rising edge of WE after the Erase Start command D0H which follows the Erase Setup command 60H. This two-cycle process for Erase operations acts as an extra layer of protection from accidental erasure of data due to external noise. The device automatically executes the Erase and Verify operations. Pass 60 D0 Block address Erase Start input: 2 cycles command 70 Status Read command Busy I/O Fail RY/BY 2000-08-27 21/33 TC58V64DC Reset The Reset mode stops all operations. For example, in the case of a Program or Erase operation the internally generated voltage is discharged to 0 volts and the device enters Wait state. The address and data registers are set as follows after a Reset: * Address Register: All 0 * Data Register: All 1 * Operation Mode: Wait state The response to an FFH Reset command input during the various device operations is as follows: When a Reset (FFH) command is input during programming Figure 8. 80 10 FF Register set Internal VPP RY/BY tRST (max 10 s) 00 When a Reset (FFH) command is input during erasing Figure 9. D0 Internal erase voltage Register set RY/BY tRST (max 500 s) FF 00 When a Reset (FFH) command is input during a Read operation Figure 10. 00 FF 00 RY/BY tRST (max 6 s) 2000-08-27 22/33 TC58V64DC When a Status Read command (70H) is input after a Reset Figure 11. FF 70 I/O status: Pass/Fail Pass Ready/Busy Ready However, the following operation is prohibited. If the following operation is executed, correct resetting of the address and data register cannot be guaranteed. FF 70 I/O status: Ready/Busy Busy RY/BY RY/BY When two or more Reset commands are input in succession Figure 12. (1) 10 FF (2) FF (3) FF RY/BY The second FF command is invalid, but the third FF command is valid. 2000-08-27 23/33 TC58V64DC ID Read The TC58V64 contains ID codes which identify the device type and the manufacturer. The ID codes can be read out under the following timing conditions: CLE tCR CE WE tAR1 ALE RE tREAID I/O 90H ID Read command 00 Address 00 98H Maker code E6H Device code For the specifications of the access times tREAID, tCR and tAR1 refer to the AC Characteristics. Figure13. ID Read timing Table 6. Code table I/O8 Maker code Device code 1 1 I/O7 0 1 I/O6 0 1 I/O5 1 0 I/O4 1 0 I/O3 0 1 I/O2 0 1 I/O1 0 0 Hex Data 98H E6H 2000-08-27 24/33 TC58V64DC APPLICATION NOTES AND COMMENTS (1) Prohibition of unspecified commands The operation commands are listed in Table 3. Input of a command other than those specified in Table 3 is prohibited. Stored data may be corrupted if an unknown command is entered during the command cycle. (2) Restriction of command while Busy state During Busy state, do not input any command except 70H and FFH. (3) Pointer control for 00H, 01H and 50H The device has three Read modes which set the destination of the pointer. Table 7 shows the destination of the pointer, and Figure 14 is a block diagram of their operations. Table 7. Pointer Destination Read Mode (1) (2) (3) Command 00H 01H 50H Pointer 0~255 256~511 512~527 00H 01H 50H Pointer control Figure 14. Pointer control 0 A 255 256 B 511 512 527 C The pointer is set to region A by the 00H command, to region B by the 01H command, and to region C by the 50H command. (Example) The 00H command must be input to set the pointer back to region A when the pointer is pointing to region C. 00H Address Start point A area Address Start point A area 00H Address Start point C area Address Start point C area Address Start point A area 50H Address Start point C area 50H 01H Address Start point B area Address Start point A area To program region C only, set the start point to region C using the 50H command. 50H 80H Address DIN Start point C area 10H Programming region C only 01H 80H Address DIN Start point B area 10H Programming regions B and C Figure 15. Example of How to Set the Pointer 2000-08-27 25/33 TC58V64DC (4) Acceptable commands after Serial Input command 80H Once the Serial Input command 80H has been input, do not input any command other than the Program Execution command 10H or the Reset command FFH. 80 WE Address input RY/BY Figure 16. FF If a command other than 10H or FFH is input, the Program operation is not performed. 80 XX 10 For this operation the FFH command is needed. Command Other than 10H or FFH Programming cannot be executed. (5) Status Read during a Read operation 00 Command CE 00 70 [A] WE RY/BY RE Address N Status Read command input Figure 17. Status Read Status output The device status can be read out by inputting the Status Read command 70H in Read mode. Once the device has been set to Status Read mode by a 70H command, the device will not return to Read mode. Therefore, a Status Read during a Read operation is prohibited. However, when the Read command 00H is input during [A], Status mode is reset and the device returns to Read mode. In this case, data output starts automatically from address N and address input is unnecessary. (6) Auto programming failure Fail 80 Address M 80 10 M If the programming result for page address M is Fail, do not try to program the page to address N in another block. Because the previous input data has been lost, the same input sequence of 80H command, address and data is necessary. Data input 10 70 I/O 80 Address N Data input 10 N Figure 18. 2000-08-27 26/33 TC58V64DC (7) RY/ BY : termination for the Ready/Busy pin ( RY/ BY ) A pull-up resistor needs to be used for termination because the RY/ BY buffer consists of an open drain circuit. VCC VCC Device CL VSS Figure 19. tr This data may vary from device to device. We recommend that you use this data as a reference when selecting a resistor value. 1.5 s 1.0 s 0.5 s 0 1 K tr 5 ns tf Ready 3.0 V RY/BY tf VCC 1.0 V Busy 1.0 V tr VCC = 3.3 V Ta = 25C CL = 100 pF 3.0 V R 15 ns 10 ns tf 2 K R 3 K 4 K (8) Status after power-on The following sequence is necessary because some input signals may not be stable at power-on. Power on FF Reset Figure 20. (9) Power-on/off sequence: The WP signal is useful for protecting against data corruption at power-on/off. The following timing sequence is necessary: 3.0 V 2.8 V 0V VCC Don't care CE , WE , RE CLE, ALE Don't care VIH WP VIL Operation Figure 21. Power-on/off Sequence VIL 2000-08-27 27/33 TC58V64DC (10) Note regarding the WP signal The Erase and Program operations are automatically reset when WP goes Low. The operations are enabled and disabled as follows: Enable Programming WE DIN 80 10 WP RY/BY tWW (100 ns min) Disable Programming WE DIN 80 10 WP RY/BY tWW (100 ns min) Enable Erasing WE DIN 60 D0 WP RY/BY tWW (100 ns min) Disable Erasing WE DIN 60 D0 WP RY/BY tWW (100 ns min) 2000-08-27 28/33 TC58V64DC (11) When four address cycles are input Although the device may read in a fourth address, it is ignored inside the chip. Read operation CLE CE WE ALE I/O 00H, 01H, 50H RY/BY Internal read operation starts when WE goes High in the third cycle. Figure 22. Address input Ignored Program operation CLE CE WE ALE I/O 80H Address input Ignored Figure 23. Data input 2000-08-27 29/33 TC58V64DC (12) Several programming cycles on the same page (Partial Page Program) A page can be divided into up to 10 segments. Each segment can be programmed individually as follows: First programming Data Pattern 1 All 1s Second programming All 1s Data Pattern 2 All 1s Tenth programming All 1s Data Pattern 10 Result Data Pattern 1 Data Pattern 2 Data Pattern 10 Figure 24. Note: The input data for unprogrammed or previously programmed page segments must be 1 (i.e. the inputs for all page bytes outside the segment which is to be programmed should be set to all 1). (13) Note regarding the RE signal The internal column address counter is incremented synchronously with the RE clock in Read mode. Therefore, once the device has been set to Read mode by a 00H, 01H or 50H command, the internal column address counter is incremented by the RE clock independently of the address input timing. If the RE clock input pulses start before the address input, and the pointer reaches the last column address, an internal read operation (array register) will occur and the device will enter Busy state. (Refer to Figure 25.) Address input I/O 00H/01H/50H WE RE RY/BY Figure 25. Hence the RE clock input must start after the address input. 2000-08-27 30/33 TC58V64DC (14) Invalid blocks (bad blocks) The device contains unusable blocks. Therefore, the following issues must be recognized: Referring to the Block status area in the redundant area allows the system to detect bad blocks in the accordance with the physical data format issued by the SSFDC Forum. Detect the bad blocks by checking the Block Status Area at the system power-on, and do not access the bad blocks in the following routine. The number of valid blocks at the time of shipment is as follows: MIN Bad Block Valid (Good) Block Number 1014 TYP. MAX 1024 UNIT Block Bad Block Figure 26. (15) Failure phenomena for Program and Erase operations The device may fail during a Program or Erase operation. The following possible failure modes should be considered when implementing a highly reliable system. FAILURE MODE Block Page Single Bit Erase Failure Programming Failure Programming Failure 10 DETECTION AND COUNTERMEASURE SEQUENCE Status Read after Erase Block Replacement Status Read after Program Block Replacement (1) Block Verify after Program Retry (2) ECC * * ECC: Error Correction Code Block Replacement Program Error occurs Buffer memory Block A When an error happens in Block A, try to reprogram the data into another (Block B) by loading from an external buffer. Then, prevent further system accesses to Block A (by creating a bad block table or by using an another appropriate scheme). Block B Figure 27. Erase When an error occurs for an Erase operation, prevent future accesses to this bad block (again by creating a table within the system or by using another appropriate scheme). (16) Chattering of Connector There may be contact chattering when the TC58V64DC is inserted or removed from a connector. This chattering may cause damage to the data in the TC58V64DC. Therefore, sufficient time must be allowed for contact bouncing to subside when a system is designed with SmartMediaTM. (17) The TC58V64DC is formatted to comply with the Physical and Logical Data Format of the SSFDC Forum at the time of shipping. 2000-08-27 31/33 TC58V64DC Handling Precaution (1) (2) (3) Avoid bending or subjecting the card to sudden impact. Avoid touching the connectors so as to avoid damage from static electricity. This card should be kept in the antistatic film case when not in use. Toshiba cannot accept, and hereby disclaims liability for, any damage to the card including data corruption that may occur because of mishandling. SSFDC Forum The SSFDC Forum is a voluntary organization intended to promote the SmartMediaTM, a small removable NAND flash memory card. The SSFDC Forum standardized the following specifications in order to keep the compatibility of SmartMediaTM in systems. The latest specifications issued by the Forum must be referenced when a system is designed with SmartMediaTM, especially with large capacity SmartMediaTM. SmartMediaTM SmartMediaTM SmartMediaTM Electrical Specifications Physical Format Specification Logical Format Specification Some electrical specifications in this data sheet show differences from the Forum's electrical specification. Complying with the Forum's electrical specification maintains compatibility with other SmartMedias. Please refer folloing SSFDC Forum's URL to get the detailed information of each specification. URL http://www.ssfdc.or.jp 2000-08-27 32/33 TC58V64DC PACKAGE DIMENSIONS * FDC-22A Unit: mm 2000-08-27 33/33 |
Price & Availability of TC58V64DC
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |