|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ASAHIKASEI [AK8813/14] AK8813/14 NTSC/PAL Digital Video Encoder GENERAL DESCRIPTION The AK8813/14 is low voltage, low power and small packaged Digital Video Encoder. It is suitable for a STB or Digital TV. It converts ITU-R.BT601/656 standard 8- bit parallel data into analog composite video signal, S-video in NTSC and PAL formats. AK8813/14 supports Copy protection, Closed Captioning and Video Blanking ID(CGMS-A) and WSS. These functions are controlled by high-speed I2C Bus interface. FEATURES * NTSC-M, PAL-B,D,G,H,I,M,N encoding. * Simultaneous composite video signal and S-video signal outputs * ITU-R BT.656 4:2:2 8-bit Parallel Input - EAV Decoding * Master/Slave Operation - Digital Field Sync I/O - Digital Vertical/Horizontal Sync I/O * Y filtering * C filtering * Triple 10-bit DACs * I2C Bus Interface (400kHz) * Closed Caption encoding (NTSC: line 21,284-SMPTE PAL: line 22,335-CCIR) * Macrovision Copy Protection Rev. 7.1 * (only AK8814 ) * VBID, CGMS-A(EIAJ CPR-1024) * WSS * On-chip color bar generator * Low power consumption * 2.8V to 3.3V operation CMOS Monolithic * 48pin LQFP Package / 57pin FBGA Package (*Note) This device is protected by U.S. patent numbers 4,631,603, 4,577,216, and 4,819,098, and other intellectual rights. The use of Macrovision's copy protection technology in the device must be authorized by Macrovision and is intended for home and other limited pay-per -view use only, unless otherwise authorized in written by Macrovision. Reverse engineering or disassembly is prohibited. 2 x over-sampling 4 x over-sampling * Single 27MHz Clock (The polarity could be inverted by SYSINV pin) Rev.00 -1- 2004/Oct ASAHIKASEI [AK8813/14] Block Diagram SELA SCL SDA CLKNV CLK HSYNC VSYNC/PD /RESET VREFOUT VREFIN u-P I/F (I C) & Register 2 Timing Generator Macrovision CGMS-A WSS VREF Generator IREF Sync-Form Generator Luma Filter (x 2 Interpolator) Input Formatter EAV Decode Y Delay 10-bit DAC Y Data[7:0] 10-bit DAC Chroma LPF Filter (x 2 Interpolator) Composite 4:2:2 to 4:4:4 (x 2 Interpolator) Sub-Carrier Generator C Delay 10-bit DAC C DVDD DVSS AVDD AVSS Rev.00 -3- 2004/Oct ASAHIKASEI [AK8813/14] ORDERING GUIDE AK8813VQ: LQFP48 Non-Macrovision (Pb Free) AK8813VG: FBGA57 Non-Macrovision AK8813VGP: FBGA57 Non-Macrovision (Pb Free) AK8814VQ: LQFP48 Macrovision (Pb Free) AK8814VG: FBGA57 Macrovision (Pb Free) Rev.00 -4- 2004/Oct ASAHIKASEI [AK8813/14] PIN LAYOUT 48pin LQFP VREFOUT VREFIN DVDD AVDD DVSS AVSS IREF UD4 UD5 UD6 UD7 DVSS SYSCLK DVDD UD8 DVDD FID/VSYNC HSYNC DVSS SYSINV 37 38 39 40 41 42 43 44 45 46 47 48 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 1 2 3 4 5 6 7 8 9 10 11 12 UD3 D7 UD2 D6 UD1 UD0 CVBS AVSS C AVDD Y AVSS /RESET PD SDA SCL SELA TEST UD9 D5 D4 DVDD DVSS D3 D2 D1 D0 TEST 57pin FBGA 9 8 7 6 5 4 3 2 1 A B C D E F G H J Bottom View Rev.00 -52004/Oct ASAHIKASEI [AK8813/14] PIN/FUNCTION 48pin LQFP No. 1 2-5, 8-11 12-13 14 15 16 17 Pin Name UD9 D7 - D0 TEST SELA SCL SDA PD I/O I/O I I I I I/O I Description Test pin. Open for normal operation 27MHz 8-Bit 4:2:2 multiplexed Y,Cb,Cr Data Input. For Rec.656 format, AK8813/14 decodes EAV. For non-Rec.656 format (without EAV), AK8813/14 operates in Master or Slave mode. Test pin. Ground for normal operation The slave address is set with this pin. "L":40H "H":42H Serial interface clock Serial interface data Power Down Pin. After returning from PD mode to normal operation, RESET Sequence should be done to AK8813/14. After this pin becomes "L", AK8813/14 starts the internal initializing sequence. After initializing sequence, AK8813/14 is set NTSC mode, Rec.656 decoding mode. All DACs Off condition. After power up, AK8813/14 must be initialized with this pin. (27MHz Clock is necessary for reset sequence.) Output of Luminance Signal. Output of the Chrominance signal Output of Composite Video signal Output of the Internal Vref. Terminate with 0.1uF or more capacitor. Input of the Reference Voltage The currents flow this pin adjusts the full-scale output current of the DAC. Connect this pin to Analog ground via a 6.8kohm resistor ( better than +/1% accuracy ). Test pin. Open for normal operation 27MHz Clock Input. The polarity could be inverted by SYSINV. Test pin. Open for normal operation Either of FID or VSYNC selected by the register. Rec.656 decode mode :Output Master mode : Output Slave mode : Input FID shows that "L" is odd field and "H" is even field. Rec.656 decode mode : Output Master mode : Output Slave mode : Input "L " : data is latched with rising edge. "H" : data is latched with falling edge. Analog Power Supply Digital Power Supply Analog Ground Digital Ground 18 /RESET I 20 22 24 27 28 29 32-39 41 43 Y C COMPOSITE VREFOUT VREFIN IREF UD0-UD7 SYSCLK UD8 FID /VSYNC O O O O I O I/O I I/O 45 I/O 46 48 21,26 6,31, 42,44 19,23,25 7,30, 40,47 HSYNC SYSINV AVDD DVDD AVSS DVSS I/O I P P G G Rev.00 -6- 2004/Oct ASAHIKASEI [AK8813/14] 57pin FBGA No. A1 B1 C1 C2 D1 D2 E1 E2 F2 F1 G2 G1 H1 J1 J2 H2 H3 J3 H4 J4 H5 J5 Pin Name NC AVSS AVDD VREFOUT VREFIN IREF DVSS DVDD UD0 UD1 UD2 UD3 UD4 NC UD5 UD6 UD7 DVSS SYSCLK DVDD UD8 DVDD I/O G P O I O G P I/O I/O I/O I/O I/O I/O I/O I/O G I P I/O P Description Open for normal operation Analog Ground Analog Power Supply Output of the Internal Vref. Terminate with 0.1uF or more capacitor. Input of the Reference Voltage The currents flow this pin adjusts the full-scale output current of the DAC. Connect this pin to Analog ground via a 6.8kohm resistor ( better than +/1% accuracy ). Digital Ground Digital Power Supply Test pin. Open for normal operation Test pin. Open for normal operation Test pin. Open for normal operation Test pin. Open for normal operation Test pin. Open for normal operation Open for normal operation Test pin. Open for normal operation Test pin. Open for normal operation Test pin. Open for normal operation Digital Ground 27MHz Clock Input. The polarity could be inverted by SYSINV. Digital Power Supply Test pin. Open for normal operation Digital Power Supply Either of FID or VSYNC selected by the register. Rec.656 decode mode :Output Master mode : Output Slave mode : Input FID shows that "L" is odd field and "H" is even field. Rec.656 decode mode : Output Master mode : Output Slave mode : Input Digital Ground "L " : data is latched with rising edge. "H" : data is latched with falling edge. Test pin. Open for normal operation Open for normal operation Video data input (MSB) Video data input J6 FID/VSYNC I/O H6 H7 J7 H8 J9 J8 G8 HSYNC DVSS SYSINV UD9 NC D7 D6 I/O G I I/O I I Rev.00 -7- 2004/Oct ASAHIKASEI H9 G9 F8 F9 E8 E9 D8 D9 C8 C9 B9 A9 A8 B8 B7 A7 D5 D4 DVDD DVSS NC D3 D2 D1 D0 TEST TEST NC SELA SCL SDA PD I I P G I I I I I I I I I/O I Video data input Video data input Digital Power Supply Digital Ground Open for normal operation Video data input Video data input Video data input Video data input Open for normal operation Open for normal operation Open for normal operation The slave address is set with this pin. "L":40H "H":42H Serial interface clock Serial interface data [AK8813/14] Power Down Pin. After returning from PD mode to normal operation, RESET Sequence should be done to AK8813/14. After this pin becomes "L", AK8813/14 starts the internal initializing sequence. After initializing sequence, AK8813/14 is set NTSC mode, Rec.656 decoding mode. All DACs Off condition. After power up, AK8813/14 must be initialized with this pin. (27MHz Clock is necessary for reset sequence.) Analog Ground Open for normal operation Output of Luminance Signal. Analog Power Supply Output of the Chrominance signal Analog Ground Output of Composite Video signal Open for normal operation Open for normal operation Open for normal operation A6 /RESET I B6 A5 B5 B4 A4 B3 A3 B2 A2 C3 AVSS NC Y AVDD C AVSS CVBS NC NC NC G O P O G O - (Note1) At ITU-R.BT656 I/F mode operation, FID/VSYNC, HSYNC pins should be pulled up to VDD with 100k-ohm Resistor (Note2) This device requires reset operation. Before resetting the state of the pin of I/O are unknown state. After reset sequence, I/Opins (FID/VSYNC, HSYNC) turns Hi-Z states. Rev.00 -8- 2004/Oct ASAHIKASEI [AK8813/14] ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Parameter Supply Voltage (VDD) DVDD, AVDD Input Pin Voltage (Vin) Input Pin Current (Iin) Analog Reference Current (IREF) Analog Output Current Storage Temperature -0.3 -40 VDD+0.3 10 0.37 11.6 125 V mA mA mA C Min -0.3 Max 4.6V Units V (Note) When all Ground pins(DVSS, AVSS) are set to 0V. Recommended Operating Conditions Parameter Supply Voltage (VDD) Operating Temperature Min 2.8 -20 Typ. 3.3 Max 3.6 85 Units V C Rev.00 -9- 2004/Oct ASAHIKASEI [AK8813/14] [Power Supply:2.8 ~ 3.6V Symbol VIH1 VIL1 IL VOH VOL1 VIH2 VIL2 VOL2 0.7VDD 0.3VDD 0.4 2.4/2.2 Note 3) 0.4 V V V V IOL = 3mA Min 0.7VDD 0.3VDD 10 Max Units V V uA V Temperature:-20 ~ 85C] Conditions Note1) Note1) Note1) IOH =-1mA Note 2) IOL = 2mA Note 2) DC Characteristics Parameter Digital Input High Voltage Digital Input Low Voltage Digital Input leak Current Digital Output High Voltage Digital Output Low Voltage I C Input High Voltage 2 I C(SDA,SCL) 2 I2C Input Low Voltage 2 I C(SDA,SCL) I2C(SDA) Output Voltage Note 1) Note 2) Note 3) Note ) D[9:0],FID/VSYNC, HSYNC, SYSCLK, /RESET pin FID/VSYNC, HSYNC pin DVDD=2.8V~3.0V VOH 2.2V Connected Test Pin to Ground, SELA and SYSINV Pin are desired polarity. Analog Characteristics [AVDD:3.3V Temperature:25C Load Resistance 220ohm IREF Resistance 6.8kohm] Parameter DAC Resolution DAC Integral linearity error DAC Differential linearity error DAC Output Full Scale Voltage DAC Output offset Voltage Unbalances between DACs Isolation between DACs DAC Load Capacitance Internal Reference Voltage Internal Reference Drift Min Typ 10 0.6 0.4 Max 2 1 1.35 5.0 5 30 Units bit LSB LSB V mV % dB pF V ppm/C Conditions 1.21 1.28 1 50 Note1) Note2) Note3) 1MHz Full Scale Note4) 1.17 1.235 -50 1.30 Note 1) Under the condition of output load 220, IREF pin with 6.8k, using internal reference. The output full-scale current IOUT is calculated as Full scale output voltage (typ. 1.28V) /220=typ. 5.82mA. Note 2) DAC output when feeding code of 0 (Decimal). Note 3) Deviation between the DAC output when feeding 1V generating code of 800(Decimal). Note 4) The value is a design target. This value is not tested. Dissipation Current [AVDD=DVDD=:3.3V Temperature:-25~85C ] Parameter DAC Current (Active mode) DAC Current (Sleep mode) Power Down Current Total Current Note 1) All DACs are operating. Note 2) All DACs are turned off with no system clock. Note 3) In case the value after power down sequence. Min Typ 24 10 10 50 Max Units mA uA Conditions Note1) Note2) Note3) Note4) 100 65 uA mA Note 4) NTSC internal color bar with 3ch DACs operation and slave mode operation. DAC output pins is connected with only 220 load. Rev.00 - 10 - 2004/Oct ASAHIKASEI [AK8813/14] AC Characteristics (2.8V - 3.6V Temperature -20 ~ 85C CL=30pF) (1). SYSCLK fCLK tCLKL tCLKH 50%Level between VIH and VIL VIH CLK VIL Parameter SYSCLK SYSCLK Pulse width H SYSCLK Pulse width L Symbol fSYSCLK tCLKH tCLKL Min. Typ. 27 Max Unit MHz nsec nsec 15 15 (2). Pixel Data Input Timing (2-1) SYSINV = Low CLK tDS D7:D0 tDH VIH VIL (2-2) SYSINV = High CLK tDS tDH VIH VIL D7:D0 Parameter Data Setup Time Data Hold Time Symbol tDS tDH Min 5 8 Typ Max Units nsec nsec Rev.00 - 11 - 2004/Oct ASAHIKASEI [AK8813/14] (3). Synchronizing Signal ( FID/VSYNC, HSYNC ) (3-1) SYSINV=Low (3-1-1) Input Timing SYSCLK tDS tDH VIH VIL FID/VSYNC, HSYNC Parameter Data Setup Time Data Hold Time Symbol tDS tDH Min 5 8 Typ. Max Units nsec nsec (3-1-2) Output Timing VIH SYSCLK tDEL FID/VSYNC, HSYNC Parameter Delay from SYSCLK Symbol tDEL Min Typ. Max 27 Units nsec Rev.00 - 12 - 2004/Oct ASAHIKASEI [AK8813/14] (3-2) SYSINV = High (3-2-1) Input Timing VIH VIL tDS tDH SYSCLK FID/VSYNC, HSYNC Parameter Data Setup Time Data Hold Time (3-2-2) Output Timing Symbol tDS tDH Min 5 8 Typ. Max Units nsec nsec SYSCLK tDEL FID/VSYNC, HSYNC Parameter Delay from SYSCLK Symbol tDEL Min Typ. Max 27 Units nsec Rev.00 - 13 - 2004/Oct ASAHIKASEI [AK8813/14] (4). Reset (Initialize) Reset Timing /RESET pRES 1 SYSCLK Hi-Z HSYNC,VSYNC,SDA 2 9 10 Indefinite state Parameter /RESET Pulse Width Symbol pRES Min 10 Typ. Max Units SYSCLK After power up, I/O pins of AK8813/14 are in the indefinite state. It should be initialize with Reset sequence. While reset sequence system clock should be input to AK8813/14 and SCL, SDA should be High state. (5) Power Down Sequence /RESET VSS VDD PD pPD 1 SYSCLK 2 99 100 101 Parameter /RESET Pulse Width Symbol pSTOP Min 100 Typ. Max Units SYSCLK During "Power Down" state, control signal should be set to VDD state or VSS state. Rev.00 - 14 - 2004/Oct ASAHIKASEI [AK8813/14] (5). I C Bus (SCL 400kHz cycle mode) 2 (5-1) I/O Timing 1 tBUF SDA tF SCL tLOW tSU:STA tR tHD:STA tR tF tSU:STO Parameter Bus Free Time Hold Time (Start Condition) Clock Pulse Low Time Bus Signal Rise Time Bus Signal Fall Time Setup Time(Start Condition) Symbol tBUF tHD:STA tLOW tR tF tSU:STA Min 1.3 0.6 1.3 Max Units usec usec usec 300 300 0.6 nsec nsec usec Setup Time(Stop Condition) tSU:STO 0.6 usec All the figures shown above list are not restricted by AK8813/14 but are restricted by I2C Bus standard. Please see the I2C Bus standard for further details. (5-2) I/O Timing 2 tHD:DAT SDA tHIGH SCL tSU:DAT Parameter Data Setup Time Data Hold Time Clock Pulse High Time Symbol tSU:DAT tHD:DAT tHIGH Min. 100 (1) 0.0 0.6 Max. Unit. nsec 0.9 (2) usec usec (Note1) In case of normal I2C bus mode tSU:DAT 250nsec (Note2) Using under minimum tLOW, this value must be satisfied. (Note3) I2C I/F reset is done by reset sequence of AK8813/14, System clock (27MHz) is necessary to do reset sequence. However, SDA pin is always Hi-Z state when PD pin is set to High. Rev.00 - 15 2004/Oct ASAHIKASEI [AK8813/14] FUNCTIONAL DESCRIPTION Reset When the reset pin [ /RESET ] set to "L", AK8813/14 is in reset state. AK8813/14 starts in the internal initializing sequence at the trailing edge of the first SYSCLK after the reset pin is "L". All internal registers are set to be default value by this initializing sequence. AK8813/14 needs at least 10 clock counts of SYSCLK for this reset operation. After the reset operation, the video output pins are in high-impedance. AK8813/14 requires SYSCLK for the reset operation. Master Clock AK8813/14 requires 27MHz clock at SYSCLK pin for operation. Video input data (ITU-R BT.656) is sampled at the trailing edge of this 27MHz. SYSINV decides the edge direction. SYSINV = L Data is sampled at rising edge of SYSCLK. SYSINV = H Data is sampled at falling edge of SYSCLK. Video Signal Interface AK8813/14 can interface with the video input data by the following 3 modes. The mode is set by the register [ Interface mode register(00H) ]. 1. ITU-R BT.656 Format AK8813/14 decodes EAV in stream data and manages an internal synchronization. In this case, AK8813/14 outputs FID (odd : "L" even : "H")/ VSYNC and HSYNC. CCIR-bit of [ Interface mode register (00H) ] should be set "1" . 2. ITU-R BT.656 like Format (4:2:2 Y/Cb/Cr) There are Master and Slave modes, for ITU-R BT.656 like Format which does not include EAV. In this mode, CCIR-bit of [ Interface mode register(00H) ] should be set "0" . AK8813/14 provides FID/VSYNC and HSYNC to an external device according to the AK8813/14 internal timing counter. AK8813/14 starts to sample the input data at the fixed value on the internal pixel counter. In this mode, following setting should be done to [Interface mode register(00H)]. CCIR-bit = 0 MAS-bit = 1 FID/VSYNC and HSYNC are supplied by an external device. AK8813/14 samples the data as same manner of Master mode. In this mode, following setting should be done to [Interface mode register(00H)]. CCIR-bit = 0 MAS-bit = 0 Rev.00 - 16 - 2004/Oct ASAHIKASEI [AK8813/14] Video Signal Conversion Video reconstruction module converts the multiplexed data (ITU-R. BT601 Y/Cb/Cr) to the interlace format of NTSC-M, PAL-M, PAL-B,D,G,H,I,N and other formats (ex. NTSC-4.43 and PAL60). The video reconstruction format, the line number, the color encode way(NTSC or PAL) and the frequency of Color Sub-carrier is specified by [Video Process 1 register(01H)]. (cf. Burst Signal Table) The frequency and the phase of Color Sub-carrier are also adjustable by [Sub C. Freq. register(06H)] and [Sub C. Phase register(07H)]. The Sub-carrier has a free-running mode and a reset-mode. In the reset-mode, the Sub-carrier is reset automatically to the initial phase for every 4 fields (NTSC) or 8 fields (PAL). Rev.00 - 17 - 2004/Oct ASAHIKASEI [AK8813/14] Luminance Filter Luminance signal passes through the 2x Low Pass filter with sin(x)/x compensation. Fig.1 is the characteristic of Luminance Filter. Luma Filter 10 0 0.0 -10 -20 -30 -40 -50 -60 Frequency [MHz] 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 Gain [dB] Fig. 1 Luminance Filter Rev.00 - 18 - 2004/Oct ASAHIKASEI [AK8813/14] Chrominance Filter Chrominance signals (Cb,Cr) before Sub-carrier modulation pass through the 1.3 MHz Low pass filter shown in Fig.2. Chrominance signal modulated by Sub-carrier passes through the filter shown in Fig.3. Frequency [MHz] 0.0 10 0 -10 Gain [dB] -20 -30 -40 -50 -60 -70 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 Fig. 2 Chroma-1 LPF 0.0 10 0 -10 Gain [dB] -20 -30 -40 -50 -60 -70 1.0 2.0 3.0 4.0 Frequency [MHz] 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 Fig. 3 Chroma-2 LPF Rev.00 - 19 - 2004/Oct ASAHIKASEI [AK8813/14] Color burst signal Color burst signal is generated by 32bits-length Digital Frequency Synthesizer. The Default frequency of the color burst is selected by [Video Process 1 Register(0x01)]. Standard Sub-carrier Freq. [MHz] Video Process 1 [VM1,VM0] [0,0] [0,1] [1,1] [1,0] [1,1] [1,1] [1,1] NTSC-M PAL-M PAL-B,D,G,H,I PAL-N(Arg.) PAL-N(non-Arg.) PAL60 NTSC-4.43 3.57954545 3.57561188 4.43361875 3.5820558 4.43361875 4.43361875 4.43361875 Burst Signal Table Sub-carrier frequency 3.57561188MHz is allowed when PAL-M mode is selected. The burst frequency and initial phase resolution are as follows. Frequency resolution SCH Phase resolution 0.8046Hz 360/256 Video DAC AK8813/14 has the three current driven 10bits-DACs at 27MHz operation. The full scale voltage of DAC is determined by the current output from IREF pin. Typical output voltage is 1.28Vo-p under the condition of VREFIN 1.235V, 6.8K between IREF pin and Ground(AVSS) and DAC load resistance of 220. This full-scale voltage should be set in the range of 1.17V to 1.33V by adjusting the resistor which terminates IREF pin. Each DAC output can be set to "active state" or to "inactive state" individually by [DAC Mode register(05H)]. When DAC is in "inactive state", the output is Hi-impedance. When all DACs are set to "inactive state", the analog part of AK8813/14 goes into sleep mode. In this case AK8813/14 stops outputting the reference voltage(VREF) output. When any DAC is switched over in "active state" from sleep mode, AK8813/14 starts outputting reference voltage. In this case AK8813/14 needs several milliseconds for VREF wake-up time. Using internal VREF as the reference voltage, connect [VREF OUT] pin with [VREF IN] pin and [VREF OUT] pin is terminated with more than 0.1uF capacitor. Use external Reference Voltage In order to improve the accuracy of DAC output, external reference voltage may be used. In this case, VREFOUT pin still needs to be terminated with more than 0.1uF capacitor. Rev.00 - 20 - 2004/Oct ASAHIKASEI [AK8813/14] Copy Protection AK8814 has the function of Macrovision copy protection. Information about the Macrovision encoding functions of the AK8814 is available to Macrovision licensees. AK8813 doesn't have this function. Macrovision Corporation 2830 De La Cruz Boulevard Santa Clara, California 95050 U.S.A. Main Telephone (switchboard): +1 408 743-8600 Main Fax: +1 408 743-8610 Technical Support Group Fax: +1 408 743-8617 Rev.00 - 21 - 2004/Oct ASAHIKASEI [AK8813/14] Closed Caption and Extended Data AK8813/14 supports both Closed Captioning and Extended Data. They are controlled "ON" or "OFF" respectively by [ Video Process 2 Register(02H) ]. Each data consists of 2 continuous bytes register( Closed Caption R (16H,17H) ), and it is recognized as the data is renewed when the second byte(17H register) is written in the register. After the data is renewed, AK8813/14 encodes Closed Captioning and Extended Data at the designated line. If the data isn't renewed, AK8813/14 outputs "ASCII-NULL" code. The data is supposed as Odd Parity and 7 bit US-ASCII code. Host should provide a parity bit. *In PAL encoding mode, AK8813/14 outputs them at the same timing and same pattern as NTSC. *The line where Closed Captioning data is encoded is as follows. 525/60 System (SMPTE) Closed Caption Extended Data 21 Line default 284 Line default 625/50 System (CCIR) 22 Line default 335 Line default 240+/- 48nsec 10.5 +/- 0.25usec 12.91 usec 240+/- 48nsec Two 7-bit + PARITY ASCII Characters Data PARITY PARITY START 50 +/- 2 IRE D0-D6 D0-D6 40IRE 10.003 +/- 0.25usec 27.382 usec 61 usec 33.764 usec Fig. 4 Closed Captioning Wave form Rev.00 - 22 - 2004/Oct ASAHIKASEI [AK8813/14] Video ID AK8813/14 supports Video ID (EIAJ standard, CPR-1204) encoding for the distinction of an aspect ratio or CGMS-A etc. Setting or Resetting the VBID-bit of [ Video Process 2 Register(02H) ], this function is switched On/Off. The data is set by using [ Video ID Data Register(1AH, 1BH) ]. VBID Data Renewal Timing. VSYNC S et C ontro l R egister I C SDA 2 N EW D AT A DATA O LD D A T A N EW D AT A Fig. 5 VBID Data renewal Timing VBID Data Layout VBID is consists of 20 bits and its format is shown as follows. AK8813/14 generates CRC code automatically and appends it to the data. Initial value of the Polynomial is 1. DATA bit1 bit20 WORD0 2bit WORD1 4bit WORD2 8bit Fig. 6 VBID code assignment CRC 6bit Rev.00 - 23 - 2004/Oct ASAHIKASEI [AK8813/14] VBID Waveform Ref. bit1 bit2 bit3 *** bit20 70IRE +/- 10IRE 0IRE + 10 IRE - 5 IRE 2.235usec +/- 50nsec 11.2usec +/- 0.3usec 11.2usec +/- 0.3usec 1H Fig. 7 VBID Wave Form 525/60 system Amplitude Encode Line 70 IRE 20/283 VBID parameter table 625/50 system 490 mV 20/333 Rev.00 - 24 - 2004/Oct ASAHIKASEI [AK8813/14] WSS AK8813/14 supports WSS(ITU-R.Bt.1119) encoding for the distinction of an aspect ratio etc. Setting or Resetting the WSS-bit of [ Video Process 2 Register(02H) ], this function is switched On/Off. The data is set by using [ WSS Data Register(08H, 09H) ]. WSS Data Renewal Timing VSYNC S et C ontro l R egister I C SDA 2 N EW D AT A DATA O LD D A T A N EW D AT A Fig. 8 WSS Data Renewal Timing 500mV +/- 50% 0H 27.4usec 1.5usec 10.5usec 11.0 +/- 0.25usec 38.4usec 44.5usec Fig. 9 WSS Wave Form Encode Line: Line 23 Coding: bi-phase modulation coding Clock: 5MHz (Ts = 200ns) Run-in 29 elements Start code 24 elements Group 1 Aspect ratio 24 elements Bit numbering 0 1 2 3 Group 2 Enhanced Services 24 elements Bit numbering 4 5 6 7 Group 3 Subtitles 18 elements Bit numbering 8 9 10 Group4 Reserved 18 elements Bit numbering 11 12 13 LSB MSB 0 : 000111 1 : 111000 0x1F1C71C7 0x1E3C1F LSB MSB 0 : 000111 1 : 111000 LSB MSB 0 : 000111 1 : 111000 LSB MSB 0 : 000111 1 : 111000 Rev.00 - 25 - 2004/Oct ASAHIKASEI [AK8813/14] AK8813/14 Interface Timing (Part 1) Master mode & ITU-R BT. 656 mode On ITU-R BT.656 decoding mode or master mode operation, AK8813/14 outputs HSYNC and FID or VSYNC (selected by register). When AK8813/14 receives ITU-R BT. 656 signal, AK8813/14 decodes [EAV] code in the data for synchronization then outputs the HSYNC. AK8813 outputs HSYNC at the rising edge of SYSCLK in the timing of the 32nd/24th(NTSC/PAL) data slot, which is counted from the [EAV] starting point as below. (See also AC Characteristics 2-2[Input Synchronizing Signal]) On master mode operation, the front device connected with AK8813/14 (ex. MPEG Decoder) starts to set Cb on the 276th/288th(NTSC/PAL) slot, after starting to count HSYNC falling edge as 32nd/24th(NTSC/PAL) slot. FID/VSYNC is output synchronously with HSYNC at the timing of solid line as in Fig. 10 Video Field. Y b/C /C r D ata# 525system C b EV A YC r Y C b Y C r Y C b Y C r Y C b SV A YC r Y C b 0 0 Y 0 0 C r 0 0 Y 1 1 C b 1 1 360 720 360 721 361 722 361 723 360 720 360 721 361 722 361 723 368 736 368 366 732 366 855 428 856 428 857 861 431 862 431 863 D ata# 625system S S LK YC 33/ 25T(525/ 625) 276/ 288T(525/ 625) HYC SN TB T D A nalogO T U 243/ 263T(525/ 625) Fig. 10 Interface Timing (ITU-R BT.656 or Master mode) Rev.00 - 26 - 2004/Oct ASAHIKASEI [AK8813/14] AK8813/14 Interface Timing (Part 2) Slave mode On slave mode operation, HSYNC and FID or VSYNC (Selected by register) are input to AK8813/14. AK8813/14 monitors the transition of HSYNC at the timing of the rising edge of SYSCLK. (Refer to AC Characteristic 2-1. [Input Synchronizing Signal]) After AK8813/14 recognizes HSYNC is Low-logic, AK8813/14 sets the slot number to the 32nd/24th(NTSC/PAL), internally, then AK8813/14 starts to sample the data as Cb on 276th/288th(NTSC/PAL) slot. Video field is recognized the transition timing between FID/VSYNC and HSYNC. (Fig.10. Video Field) As in the figure, there is a tolerance of 1/4H. 244T / 264T (525/625) 27MHz Data HSYNC Cb0 Y0 Cr0 Y1 Cb1 Y2 Cr1 TBD-clk Fig. 11 Interfacing timing (Slave mode) 1/2 H HSYNC Start of 1st Field VSYNC/FIELD Start of 2nd Field VSYNC/FIELD 1/4 H 1/4 H 1/2 H 1/4 H1/4 H Fig. 12 Video Field Rev.00 - 27 - 2004/Oct ASAHIKASEI [AK8813/14] HSYNC FID/VSYNC Timing 525 System Digital Line-No. HSYNC VSYNC FID 525 1 2 3 4 5 6 7 8 9 10 11 Digital Line-No. HSYNC VSYNC FID 262 263 264 265 266 267 268 269 270 271 272 273 274 625 System Digital Line-No. HSYNC VSYNC FID 622 623 624 625 1 2 3 4 5 6 7 8 Digital Line-No. HSYNC VSYNC FID 310 311 312 313 314 315 316 317 318 319 320 Fig. 13 HSYNC FID/VSYNC Timing Rev.00 - 28 - 2004/Oct ASAHIKASEI [AK8813/14] Internal Color Bars Generator AK8813/14 generates the Common Color Bar signal for NTSC and PAL internally. The generated Color Bar is "100% Amplitude, 100% Saturation". When AK8813/14 is set to Black Burst output mode, AK8813/14 does not output Color bar even Color bar output register is set. WHITE YELLOW CYAN GREEN MAGENTA RED BLUE BLACK Luminance 100%White Synctip Level Blanking Level Chrominance Fig. 14 Luminance and Chrominance waveform The following values are code for ITU-R. BT601 Cb Y Cr WHITE 128 235 128 YELLOW 16 210 146 CYAN 166 170 16 GREEN 54 145 34 MAGENTA 202 106 222 RED 90 81 240 BLUE 240 41 110 BLACK 128 16 128 Internal Black Burst Generator AK8813/14 generates Black burst signal for NTSC and PAL internally. When AK8813/14 is set to Black burst output mode, AK8813/14 works same operation as that the input Y/Cb/Cr data is 16/128/128. In this mode, AK8813/14 does not output Color bar even Color bar output register is set. Rev.00 - 29 - 2004/Oct ASAHIKASEI [AK8813/14] Synchronizing Signal and Burst Waveform (1-1) NTSC / NTSC-4.43 / PAL-M( Video Process 1 Register [VM3:VM2]-bit = 00 / 01 ) (SMPTE-170M) H o r iz o n ta l B la n k in g r is e t im e 90% 50% B u r s t E n v e lo p e r is e tim e 90% 10% 90% B u rs t H o r iz o n ta l r e f e r e n c e p o in t 50% 10% S yn c H . r e f . t o B u r s t S ta r t H b la n k in g s ta r t to H -re fe re n c e H r e f e r e n c e t o B la n k in g E n d 50% S yn c L e ve l B u r s t H e ig h t 50% 10% S y n c r is e t im e Fig. 15 Synchronizing Signal and Burst Waveform measurement point Total line period(derived) Sync Level Horizontal Blanking rise time Sync rise time Burst envelope rise time H-Blanking start to H-reference Horizontal Sync Horizontal reference point to burst start H reference to H-blanking end Burst Burst Height * 63.556 40 140 140 300 1.5 4.7 19 9.2 9 40 value Recommended tolerance +/- 1 +/- 20 +/- 20 +200 -100 +/- 0.1 +/- 0.1 defined by SC/H + 0.2 -0.1 +/- 1 +/- 1 units usec IRE nsec nsec nsec usec usec cycles usec cycles IRE 10% - 90% 10% - 90% 10% - 90% 50% 50% 50% 50% 50% * Burst height of PAL-M is 306mV 19 cycles +/-10 9 cycles 50% Fig. 16 Synchoronizing Signal and Burst Waveform(NTSC) Rev.00 - 30 - 2004/Oct ASAHIKASEI [AK8813/14] (1-2-1) HSYNC Timing (NTSC/NTSC4.43) 3H B A 0 .5 H D 3H E 3H F 1 C 2 3 4 5 6 7 8 9 19 1 9 + 1 /- 2 L in e (S e t C o n tro l R e g is te r) 3H 0 .5 H 3H 3H 263 264 265 266 267 268 269 270 271 272 273 283 Fig. 17 HSYNC Timing Symbol A B C D E F Duration 429T 858T 31T 429T 858T 63T Measurement point Reference 50% 13.5MHz Clock G H I I I I 286mV Equalizing Pulse Fig. 18 Symbol Field Period (derived) Frame period (derived) Vertical blanking start before equalizing pulse Vertical blanking (63.556usec x 20lines + 1.5usec) Pre-equalizing duration Pre-equalizing pulse width Vertical sync duration Vertical serration pulse width Post-equalizing duration Post-equalizing pulse width Sync rise time Serration Pulse Equalizing Pulse and Serration Pulse Measurement point Value 16.6833 33.3667 first 50% 1.5 19* lines + 1.5 usec 3 2.3 3 4.7 3 2.3 140 +/- 0.1 0 +/- 0.1 +/- 0.1 +/- 0.1 +/- 0.1 +/- 20 Recommended tolerance units msec msec usec lines usec lines usec lines usec lines usec nsec G H 50% 50% 50% G I *This value can be set by the register. Rev.00 - 31 - 2004/Oct ASAHIKASEI [AK8813/14] (1-2-2) FID/VSYNC Timing and Phase of Burst (PAL-M) A B 519 520 521 522 523 524 525 1 2 3 4 5 6 7 8 A 9 B 10 257 258 259 260 261 262 263 264 265 266 267 268 269 270 A 271 B 272 519 520 521 522 523 524 525 1 2 3 4 5 6 7 A 8 B 9 10 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 Fig. 19 FID/VSYNC Timing and Phase of Burst A : Phase of Burst : nominal Value + 135 B : Phase of Burst : nominal Value - 135 Rev.00 - 32 - 2004/Oct ASAHIKASEI [AK8813/14] (2-1) PAL-B,D,G,H,I,N / PAL-60 ( Video Process 1 Register [VM3:VM2]-bit = 11) H o r iz o n ta l B la n k in g r is e t im e 90% 50% B u r s t E n v e lo p e r is e tim e 90% 10% 90% B u rs t H o r iz o n ta l r e f e r e n c e p o in t 50% 10% H o r iz o n ta l S y n c H . r e f . t o B u r s t S ta r t H b la n k in g s ta r t to H -re fe re n c e H r e f e r e n c e t o B la n k in g E n d 50% S yn c L e ve l B u r s t H e ig h t 50% 10% S y n c r is e t im e Fig. 20 PAL Waveform measurement point Total line period(derived) Sync Level Horizontal Blanking rise time Sync rise time Burst envelope rise time H-Blanking start to H-reference Horizontal Sync Horizontal reference point to burst start H reference to H-blanking end Burst * Burst Height ** 64.0 300 0.3 0.2 1.5 4.7 19 10.5 10 300 value Recommended tolerance units usec mV usec usec nsec usec usec cycles usec cycles mV 10% - 90% 10% - 90% 10% - 90% 50% 50% 50% 50% 50% +/- 0.1 +/- 0.1 +/- 0.3 +/- 0.2 defined by SC/H +/- 1 Rev.00 - 33 - 2004/Oct ASAHIKASEI [AK8813/14] (2-2) FID/VSYNC Timing and Phase of Burst PAL-B,D,G,H,I,N / PAL-60 ( Video Process 1 Register [VM3:VM2]-bit = 11) A B 308 309 310 311 312 313 314 315 316 317 318 319 A 320 B 321 322 620 621 622 623 624 625 1 2 3 4 5 6 A 7 B 8 308 309 310 311 312 313 314 315 316 317 318 A 319 B 320 321 322 620 621 622 623 624 625 1 2 3 4 5 6 7 8 Fig. 21 FID/VSYNC Timing and Phase of Burst A : Phase of Burst : nominal Value + 135 B : Phase of Burst : nominal Value - 135 Rev.00 - 34 - 2004/Oct ASAHIKASEI [AK8813/14] I2C Control Sequence AK8813/14 is controlled by I2C bus. The slave address can be selected as 40H or 42H by selecting SELA pin. SELA PULL Down [Low] PULL UP [High] SLAVE Address 0x40 0x42 Operation : Write Sequence: (a)1byte Write Sequence S Slave Address 8-bits w A 1bit Sub Address 8-bits A 1bit Data 8-bits A 1bit Stp (b) Sequential Write Operation S Slave Address 8-bits w A 1bit Sub Address(n) 8-bits A 1bit Data(n) 8-bits A 1bit Data(n+1) 8-bits A 1bit *** Data(n+m) 8-bits A 1bit stp Read Sequence: S Slave Address 8-bits w A Sub Address(n) 8-bits A rS Slave Address 8-bits R A Data1 8-bits A Data2 8-bits A Data3 8-bits A *** Data n 8-bits stp 1 1 1 1 1 1 1 S, rS : Start Condition A: Acknowledge (SDA Low ) : Not Acknowledge (SDA High) stp : Stop Condition R/W 1 : Read 0 : Write : Master device (Host) : Slave device (AK8813/14) Rev.00 - 35 - 2004/Oct ASAHIKASEI [AK8813/14] Register Map Sub Address 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x16 0x17 0x18 0x19 0x1A 0x1B 0x24 0x25 0x26 Register Default 0x00 0x00 0x00 0x00 0xAA 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R Function Interface Mode Register Video Process 1 Register Video Process 2 Register Video Process 3 Register Reserved Register DAC Mode Register Sub Carrier Frequency Register Sub Carrier Phase Register WWS Data 1 Register WWS Data 2 Register Closed Caption 1 Register Closed Caption 2 Register Closed Caption Extended 1 Register Closed Caption Extended 2 Register Video ID 1 Register Video ID 2 Register Status Register Device ID Register Device Revision Register Setting Interface mode Setting Standard (NTSC, PAL etc.) Setting Closed Caption/Extended Data/VBID Setting Composite signal or Component signal Adjusting Chrominance/Luminance Delay Each DAC On/Off Switch Adjusting Sub-carrier frequency Adjusting Sub-carrier phase WSS Data Register WSS Data Register Closed Caption Lower byte Data Closed Caption Upper byte Data Extended Lower byte Data Extended Upper byte Data Video ID Lower byte Data Video ID Upper byte Data Status Device ID Revision Rev.00 - 36 - 2004/Oct ASAHIKASEI [AK8813/14] Interface Mode Register (R/W) [Address 0x00] Sub Address 0x00 bit 7 BLN4 1 bit 6 BLN3 0 bit 5 BLN2 1 bit 4 bit 3 BLN1 BLN0 Default Value 0 0 bit 2 FID 1 Default Value 0xA4 bit 1 MAS 0 bit 0 REC656 0 Interface Mode Register Definition BIT bit 0 bit 1 bit 2 bit 3 ~ bit 7 Register Name REC656 MAS FID BLN0 ~ BLN4 REC656 I/F mode bit Master mode Set bit Field ID Set bit Blanking Line No bit R/W R/W R/W R/W R/W Definition 0 : REC656 non-decode 1 : REC656 decode (At Rec.656 mode operation, MAS-bit should be 0.) 0 : Slave mode 1 : Master mode When REC=0,it's valid 0 : Select VSYNC 1 : Select FID Line Blanking No. Rev.00 - 37 - 2004/Oct ASAHIKASEI [AK8813/14] Video Process 1 Register (R/W) [Address 0x01] Sub Address 0x01 bit 7 BBG 0 bit 6 CBG 0 bit 5 SETUP 1 bit 4 bit 3 SCR VM3 Default Value 1 0 bit 2 VM2 0 Default Value 0x30 bit 1 VM1 0 bit 0 VM0 0 Video Process 1 Register Definition BIT Register Name R/W Definition [VM1:VM0]-bit 00 : 3.57954545 MHz 01 : 3.57561188 MHz 10 : 3.5820558 MHz 11 : 4.43361875 MHz [VM3:VM2]-bit 00 : 525/60 01 : 525/60 PAL (PAL-M etc.) 10 : Reserved 11 : 625/50 PAL (PAL-B,D,G,H,I,N) 0 : Sub C. Phase Reset off 1 : Standard Field Reset 0 : No Set-up 1 : 7.5 IRE Set-up 0 : Video Encode 1 : Generates color bar 0 : Video Encode 1 : Generates black burst bit 0 ~ bit 3 VM0 ~ VM3 Video Mode 0 Register ~ Video Mode 3 Register R/W bit 4 bit 5 bit 6 bit 7 SCR SETUP CBG BBG Sub Carrier Reset bit Setup bit Color Bar Generator bit Black Burst Generator R/W R/W R/W R/W Register Setting of each standard is shown as following ; VM3-VM0 NTSC-M PAL-B,D,G,H,I PAL-M PAL-60 NTSC4.43 0000 1111 0101 0111 0011 * When SCR is "ON", the Subcarrier Phase is reset every 4 fields for NTSC, every 8 fields for PAL. * Even when SETUP is "ON", there is no Set-up (Pedestal) during the blanking lines. Rev.00 - 38 - 2004/Oct ASAHIKASEI [AK8813/14] Video Process 2 Register (R/W) [Address 0x02] Sub Address 0x02 bit 7 Reserved 0 bit 6 Reserved 0 bit 5 Reserved 0 bit 4 bit 3 Reserved WSS Default Value 0 0 bit 2 CC284 0 default Value 0x00 bit 1 CC21 0 bit 0 VBID 0 Video Process 2 Register Definition BIT bit 0 bit 1 bit 2 bit 3 bit 4 ~ bit 7 Register Name VBID CC21 CC284 WSS Reserved Video ID bit Closed Caption bit Closed Caption Extended Data bit WSS set bit Reserved bit R/W R/W R/W R/W R/W R/W 0 : Video ID off 1 : Video ID on 0 : Closed caption off 1 : Closed Caption on 0 : Extended Data off 1 : Extended data on 0 : WSS off 1 : WSS on Reserved Definition Video Process 3 Register (R/W) [Address 0x03] Sub Address 0x03 bit 7 Reserved 0 bit 6 Reserved 0 bit 5 SYD2 0 bit 4 bit 3 SYD1 SYD0 Default Value 0 0 bit 2 CYD2 0 default Value 0x00 bit 1 CYD1 0 bit 0 CYD0 0 Video Process 3 Register Definition BIT bit 0 ~ bit 2 bit 3 ~ bit 5 bit 6 ~ bit 7 Register Name CYD0 ~ CYD2 SYD0 ~ SYD2 Reserved R/W Composite Y Delay bit S-video Y Delay bit Definition R/W S-Video Y Component delay no. from Chroma: 2's comp. R/W Composite Y Component delay no. from Chroma: 2's comp. Reserved bit R/W Reserved * S-video and Y component of the composite signal can be shifted for the chroma signal independently at 3-system clock (27MHz). Rev.00 - 39 - 2004/Oct ASAHIKASEI [AK8813/14] Reserved Register (R/W) [Address 0x04] Sub Address 0x04 bit 7 Reserved 1 bit 6 Reserved 0 bit 5 Reserved 1 bit 4 bit 3 Reserved Reserved Default Value 0 1 bit 2 Reserved 0 default Value 0xAA bit 1 Reserved 1 bit 0 Reserved 0 Reserved BIT bit 0 ~ bit 7 Register Name Reserved Reserved bit. R/W Definition R/W Reserved DAC Mode Register (R/W) [Address 0x05] Sub Address 0x05 bit 7 Reserved 0 bit 6 Reserved 0 bit 5 Reserved 0 bit 4 bit 3 Reserved Reserved Default Value 0 0 bit 2 OUTCP 0 default Value 0x00 bit 1 OUTC 0 bit 0 OUTY 0 DAC Mode Register Definition BIT bit 0 Register Name OUTY YDAC Out bit R/W 0: Y signal output : OFF 1: Y signal output : ON 0: Chrominance signal output : OFF 1: Chrominance signal output : ON 0: Composite video signal or U signal output : OFF 1: Composite video signal or U signal output : ON Reserved Definition R/W bit 1 OUTC CDAC Out bit R/W bit 2 bit 3 ~ bit 7 OUTCP CPDAC Out bit R/W Reserved Reserved bit. R/W * Video output of AK8813/14 (DAC) can be forced "OFF" independently. The output of DAC that is forced "OFF" is Hi-impedance. When three DACs are forced "OFF", then the internal VREF is also forced "OFF". In this case, it takes several milliseconds before the internal VREF reaches the proper voltage after any DAC becomes "ON". Rev.00 - 40 - 2004/Oct ASAHIKASEI [AK8813/14] Sub Carrier Frequency Control Register (R/W) [Address 0x06] Sub Address 0x06 bit 7 SUBF7 0 Bit 6 SUBF6 0 bit 5 SUBF5 0 bit 4 bit 3 SUBF4 SUBF3 Default Value 0 0 bit 2 SUBF2 0 default Value 0x00 bit 1 SUBF1 0 bit 0 SUBF0 0 Sub Carrier Frequency Control Register Definition BIT bit 0 ~ bit 7 Register Name SUBF0 ~ SUBF7 R/W Sub Carrier Frequency Control bit Definition Adjustment of frequency between R/W +127 and -128 step of 0.8Hz Sub Carrier Phase Control Register (R/W) [Address 0x07] Sub Address 0x07 bit 7 SUBP7 0 Bit 6 SUBP6 0 bit 5 SUBP5 0 bit 4 bit 3 SUBP4 SUBP3 Default Value 0 0 bit 2 SUBP2 0 default Value 0x00 bit 1 SUBP1 0 bit 0 SUBP0 0 Sub Carrier Phase Control Register Definition BIT bit 0 ~ bit 7 Register Name SUBP0 ~ SUBP7 R/W Sub Carrier Phase Control bit Definition Adjustment of frequency between R/W +127 and -128 step of 0.8Hz * Sub- carrier phase is adjustable by (360 /256) step. WSS Data 1 Register (R/W) [Address 0x08] WSS Data 2 Register (R/W) [Address 0x09] Sub Address 0x08 bit 7 G2-7 0 bit 6 G2-6 0 bit 5 G2-5 0 bit 4 bit 3 G2-4 G1-3 Default Value 0 0 bit 2 G1-2 0 default Value 0x00 bit 1 G1-1 0 bit 0 G1-0 0 Sub Address 0x09 bit 7 Reserved 0 bit 6 Reserved 0 bit 5 G4-13 0 bit 4 bit 3 G4-12 G4-11 Default Value 0 0 bit 2 G3-10 0 default Value 0x00 bit 1 G3-9 0 bit 0 G3-8 0 * AK8813/14 generates the necessary sub-carrier frequency from a system clock by DFS (Digital Frequency Synthesizer) * Frequency of default is adjustable by specifying this bit. This bit adjusts the default frequency. Rev.00 - 41 2004/Oct ASAHIKASEI [AK8813/14] Closed Caption Data 1 Register (R/W) [Address 0x16] Closed Caption Data 2 Register (R/W) [Address 0x17] Sub Address 0x16 bit 7 CC7 0 bit 6 CC 6 0 bit 5 CC5 0 bit 4 bit 3 CC4 CC3 Default Value 0 0 bit 2 CC2 0 default Value 0x00 bit 1 CC1 0 bit 0 CC0 0 Sub Address 0x17 bit 7 CC15 0 bit 6 CC14 0 bit 5 CC13 0 bit 4 bit 3 CC12 CC11 Default Value 0 0 bit 2 CC10 0 default Value 0x00 bit 1 CC9 0 bit 0 CC8 0 Closed Caption Extended Data 1 Register (R/W) [Address 0x18] Closed Caption Extended Data 2 Register (R/W) [Address 0x19] Sub Address 0x18 bit 7 EXT7 0 bit 6 EXT6 0 bit 5 EXT5 0 bit 4 bit 3 EXT4 EXT3 Default Value 0 0 bit 2 EXT2 0 default Value 0x00 bit 1 EXT1 0 bit 0 EXT0 0 Sub Address 0x19 bit 7 EXT15 0 bit 6 EXT14 0 bit 5 EXT13 0 bit 4 bit 3 EXT12 EXT11 Default Value 0 0 bit 2 EXT10 0 default Value 0x00 bit 1 EXT9 0 bit 0 EXT8 0 * When the 2nd byte of Closed Caption Data and Extended Data is written in, AK8813/14 recognizes the renewed data and encodes it in the video line. When the data is not renewed AK8813/14 outputs NULL code. Rev.00 - 42 - 2004/Oct ASAHIKASEI [AK8813/14] Video ID 1 Register (R/W) [Address 0x1A] Video ID 2 Register (R/W) [Address 0x1B] Sub Address 0x1A bit 7 Reserved 0 bit 6 Reserved 0 bit 5 VBID1 0 bit 4 bit 3 VBID2 VBID3 Default Value 0 0 bit 2 VBID4 0 default Value 0x00 bit 1 VBID5 0 bit 0 VBID6 0 Sub Address 0x1B bit 7 VBID7 0 bit 6 VBID8 0 bit 5 VBID9 0 bit 4 bit 3 VBID10 VBID11 Default Value 0 0 bit 2 VBID12 0 default Value 0x00 bit 1 VBID13 0 bit 0 VBID14 0 * Please write value 0 at Reserved bit. * Bit numbers correspond to Fig. 5 VBID code assignment. * AK8813/14 generates CRC 6 bit data automatically. Status Register (R/W) [Address 0x24] Sub Address 0x24 bit 7 Reserved bit 6 Reserved bit 5 EN284 bit 4 EN21 bit 3 SYNC bit 2 STS2 bit 1 STS1 bit 0 STS0 Status Register Definition BIT bit 0 ~ bit 2 bit 3 Register Name STS0 ~ STS2 SYNC bit R/W Status bit Definition R Shows the processing field No. 0 : Missing synchronization in slave mode. 1 : Synchronization was achieved. 0 : Wait for the appointed video line to encode. 1 : Ready for the C.C. data input to the register. 0 : Wait for the appointed video line to encode. 1 : Ready for the C.C. data input to the register. Reserved S-video Y Delay bit R bit 4 EN21 Encode21 bit R bit 5 bit 6 ~ bit 7 EN284 Encode 284 bit R Reserved Reserved bit. R * Status Register becomes effective when SYNC bit turns to "1". When in master mode operation, this bit is "1". * STS2-STS2 holds the field number of processing. acquisition. Some time lag is inevitable for theI2C * Closed caption data should be renewed after firm that the EN* flag is "1". EN* flag bit is cleared after the second byte( Sub address 17H,19H) was accessed. * Reserved-bit is always value 0. Rev.00 - 43 2004/Oct ASAHIKASEI [AK8813/14] Device ID Register (R/W) [Address 0x25] Sub Address 0x25 bit 7 DEV7 0 Bit 6 DEV6 0 bit 5 DEV5 0 bit 4 bit 3 DEV4 DEV3 Default Value 1 0 bit 2 DEV2 1 default Value 0x14 bit 1 DEV1 0 bit 0 DEV0 0 Device ID Register Definition BIT bit 0 ~ bit 7 Register Name DEV0 ~ DEV7 R/W Shows the Device ID. Device ID bit R Definition "0x13" is assigned for AK8813. "0x14" is assigned for AK8814. Revision ID Register (R/W) [Address 0x26] Sub Address 0x26 bit 7 REV7 0 Bit 6 REV6 0 bit 5 REV5 0 bit 4 bit 3 REV4 REV3 Default Value 0 0 bit 2 REV2 0 default Value 0x00 bit 1 REV1 0 bit 0 REV0 0 Revision ID Register Definition BIT bit 0 ~ bit 7 Register Name REV0 ~ REV7 R/W Definition This value will be modified when the control software Revision ID bit R has to be modified. Shows the Revision ID. Rev.00 - 44 - 2004/Oct ASAHIKASEI [AK8813/14] SYSTEM CONNECTION EXAMPLE COMPOSITE D0 - D7 MPEG Decoder FID/ VSYNC HSYNC VREFOUT VREFIN SYSCLK YC220 Amp + LPF 75 I C Bus 2 SDA SCL AK8813/14 IREF DVSS AVSS AVDD 0.1uF 10uF Digital 3.3V DVDD 6.8k Analog 3.3V 10uF 0.1uF 0.1uF 10uF Digital GND Analog GND Rev.00 - 45 - 2004/Oct ASAHIKASEI [AK8813/14] PACKAGE 48pin LQFP 9.0 0.2 7.0 1.70 Max 1.4 TYP 0.13 0.13 9.0 0.2 48 1 0.17 0.08 0.10 M 0.5 0.22 0.08 010 0.10 0.5 0.2 Units = mm Package & Lead frame material Package molding compound : Lead frame material : Lead frame surface treatment : Epoxy Cu Solder plate Rev.00 - 46 - 2004/Oct ASAHIKASEI [AK8813/14] 57Pin FBGA 0.05 M S AB 9876 54 3 21 A B C D E F G H J A 5.0 0.1 57 - 0.3 0.05 B 5.0 0.1 4.0 0.5 4.0 = 0.5x8 0.20 S 0.5 S SEATING PLANE Package & Lead frame material Package molding compound: Interposer material: BT resin Epoxy Rev.00 0.25 0.05 1.00MAX 0.08 S - 47 - 2004/Oct ASAHIKASEI [AK8813/14] 48pin LQFP (Pb Free Package) 1) Asahi Kasei Logo 2) Marketing Code : AK8813 3) Date Code : XXXXXXX (7 digits) AK8813VQ 4) Pin #1 indication Rev.00 - 48 - 2004/Oct ASAHIKASEI [AK8813/14] 57Pin FBGA 1) Pin #1 indication 2) Marketing Code : 8813 8813 YWWL 3) Date Code : YWWL (4 digits) Y: Year WW: week L: Lot 57Pin FBGA (Pb Free Package) 1) Pin #1 indication 2) Marketing Code : 8813P 8813P YWWL 3) Date Code : YWWL (4 digits) Y: Year WW: week L: Lot Rev.00 - 49 - 2004/Oct ASAHIKASEI [AK8813/14] 48pin LQFP (Pb Free Package) 1) Asahi Kasei Logo 2) Marketing Code : AK8814 3) Date Code : XXXXXXX (7 digits) AK8814VQ 4) Pin #1 indication Rev.00 - 50 - 2004/Oct ASAHIKASEI [AK8813/14] 57Pin FBGA (Pb Free Package) 1) Pin #1 indication 2) Marketing Code : 8814 8814 YWWL 3) Date Code : YWWL (4 digits) Y: Year WW: week L: Lot Rev.00 - 51 - 2004/Oct ASAHIKASEI [AK8813/14] IMPORTANT NOTICE * These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. * AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. * Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. * AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, unclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. * It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. Rev.00 - 52 - 2004/Oct |
Price & Availability of AK8813P |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |