|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Product Description Stanford Microdevices CGA-6618 is a high performance GaAs HBT MMIC Amplifier. Designed with the InGaP process technology for excellent reliability. A Darlington configuration is utilized for broadband performance. The heterojunction increases breakdown voltage and minimizes leakage current between junctions. The amplifier contains two amplifiers for use in wideband Push-Pull CATV amplifiers requiring excellent second order performance. The second and third order non-linearities are greatly improved in the push pull configuration. Amplifier Configuration Preliminary Preliminary CGA-6618 Dual CATV Broadband High Linearity GaAs HBT Amplifier Product Features Excellent CSO/CTB/XMOD Performance at 1 2 3 4 8 7 6 5 +34 dBmV Output Power per Tone Dual Devices in each SOIC-8 Package simplify Push-Pull configuration PC board layout Operates from a single supply Dropping Resistor provides Temperature Compensation Applications CATV Head End Driver and Predriver Amplifier CATV Line Driver Amplifier R BIAS=39 Ohms TL = 2 5 C ZS = ZL = 75 Ohms Freq. 50 MHz 500 MHz 860 MHz U nits Min. Ty p. 14.0 14.1 14.0 72 82 74 38 40 40 21.5 21.5 21.0 12.5 17.0 13.5 10.0 19.0 13.5 3.9 4.1 4.4 81 70 65 4.7 Max. Key 75 Ohm Parameters at Room Temperature 50-860MHz CATV Band Data Test C onditions: V S = 8.0 V lD= 160mA Gai n dB Output IP 2 Tone spaci ng = 1 MHz P out/Tone = +6 dB m Tone spaci ng = 1 MHz P out/Tone = +6 dB m 50 MHz 500 MHz 860 MHz 50 MHz 500 MHz 860 MHz 50 MHz 500 MHz 860 MHz 50 MHz 500 MHz 860 MHz 50 MHz 500 MHz 860 MHz dB m Output IP 3 dB m Output P 1dB dB m Input Return Loss dB Output Return Loss dB Noi se Fi gure C SO C TB X MOD Vd A verage of 3 devi ces B alun Inserti on Loss Included Worst C ase Over B and Worst C ase Over B and Worst C ase Over B and 79 C h., Flat, +34dB mV 79 C h., Flat, +34dB mV 79 C h., Flat, +34dB mV 50 MHz 500 MHz 860 MHz dB dB c dB c dB c V Note: Measured in Push-Pull Application test board The information provided herein is believed to be reliable at press time. Stanford Microdevices assumes no responsibility for inaccuracies or omissions. Stanford Microdevices assumes no responsibility for the use of this information, and all such information shall be entirely at the users own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. Stanford Microdevices does not authorize or warrant any Stanford Microdevices product for use in life-support devices and/or systems. Copyright 2001 Stanford Microdevices, Inc. All worldwide rights reserved. 726 Palomar Ave., Sunnyvale, CA 94085 Phone: (800) SMI-MMIC http://www.stanfordmicro.com EDS-101994 Rev B Preliminary CGA-6618 Dual GaAs HBT Amplifier Typical S-Parameters @ VS=8V, ID=160mA, RBIAS=39 Ohms, TL=+25C Gain vs. Frequency 15 13 S21 (dB) 11 9 7 5 0 200 400 600 800 1000 Frequency (MHz) -40C 25C 85C Output Return Loss vs. Frequency -5 -40C 25C 85C Input Return Loss vs. Frequency -5 -10 -10 S22 (dB) -15 S11 (dB) -15 -40C 25C 85C 0 200 400 600 Frequency (MHz) 800 1000 -20 -20 -25 0 200 400 600 800 1000 -25 Frequency (MHz) Absolute Maximum Ratings Parameter Max. D evi ce C urrent (ID) Max. RF Input Power Max. Juncti on Temp. (TJ) Operati ng Temp. Range (TL) Max. Storage Temp. Absolute Limit 240 mA +16 dBm +150C -40C to +85C +150C Operati on of thi s devi ce beyond any of these li mi ts may cause permanent damage. Bias Conditions should also satisfy the following expression: IDVD (max) < (TJ - TL)/Rth,j-l 726 Palomar Ave., Sunnyvale, CA 94085 Phone: (800) SMI-MMIC 2 http://www.stanfordmicro.com EDS-101994 Rev B Preliminary CGA-6618 Dual GaAs HBT Amplifier Typical RF Performance @ VS=8V, ID=160mA, RBIAS=39 Ohms, TL=+25C IP3 vs. Temperature IP2 vs. Temperature 50 45 IP3 (dBm) IP2 (dBm) 90 85 80 75 70 65 60 0 0 .2 0 .4 0 .6 0 .8 1 -4 0C 2 5C 8 5C 40 35 30 25 20 Frequency (MHz) Second Harmonic vs. Pout and Freq. Data shown is typical at 25C -40C 25C 85C 0 0 .2 0 .4 0 .6 0 .8 1 Frequency (MHz) Third Harmonic vs. Pout and Freq. Data shown is typical at 25C 100 90 80 IM2 (dBc) 100 90 80 IM3 (dBc) 70 60 50 40 30 20 0 3 6 9 12 15 Pout (dBm) Push-Pull CGA-6618 Noise Figure 50MHz-900MHz, Typical 6 6 M Hz 100MHz 250MHz 500MHz 70 60 50 40 30 20 0 3 6 9 12 15 Pout (dBm) Push-Pull CGA-6618 CTB/CSO/XMOD 34 dBmV/Ch., 79 Ch.,Flat 66M Hz 100M Hz 250M Hz 500M Hz 6 5 4 NF (dB) 110 100 90 80 dBc 3 2 1 0 0 200 400 600 800 1000 Frequency (MHz) 70 60 50 40 0 100 200 300 400 Frequency (MHz) 500 600 C TB C SO+ C SOX m od 726 Palomar Ave., Sunnyvale, CA 94085 Phone: (800) SMI-MMIC 3 http://www.stanfordmicro.com EDS-101994 Rev B Preliminary CGA-6618 Dual GaAs HBT Amplifier Pin # 1 2,3 4 Function RF IN Device 1 Ground RF IN Device 2 Description RF input pin. This pin requires the use of an external DC blocking capacitor as show n in the schematic. Connection to ground. Use via holes for best performance to reduce lead inductance as close to ground leads as possible. Same as pin 1 1 Device Pin Out 8 5 RF output and bias pin. Bias should be supplied to this pin through an external series resistor RF OUT / Vcc and RF choke inductor. Because DC biasing is present on this pin, a DC blocking capacitor should be used in most applications (see application schematic). The supply side of the bias Device 2 netw ork should be w ell bypassed. Ground Same as pins 2 and 3 2 7 3 6 6,7 8 EPAD RF OUT / Vcc Same as pin 5 Device 1 Ground Exposed area on the bottom side of the package must be soldered to the ground plane of the board for optimum thermal and RF performance. Several vias should be located under the EPAD as show n in the recommended land pattern below. 4 5 Basic Application Schematic 50-860 MHz Vs RBIAS 1F Tant. 0.01F 1000pF 68pF Rbias Evalution Board Layout 50-860 MHz 1uF Tant. 220 nH 1 8 Amp 1 RF INPUT .01uF 1000pF 68pF RF OUTPUT Macom ETC1-1-13 1000 pF 2,3 6,7 1000 pF Balun ETC1-1-13 220nH 1000pF 1000pF Balun ETC1-1-13 1000 pF 4 Amp 2 5 1000 pF Macom ETC1-1-13 1000pF 220nH 1000pF 68pF 1000pF .01uF CGA-6618 SOIC-08 220 nH 1uF Tant. 1F Tant. 0.01F 1000pF 68pF Rbias ECB-101611 Rev A ESOP-8 Push-Pull Eval Board RBIAS Vs Recommended Land Pattern .15 [3.81] Recommended Bias Resistor Values for ID=160mA Supply Voltage(VS) RBIAS RBIAS Pow er Rating 8V 39 1/2W 9V 56 1/2W 12V 91 1W 15V 130 1W .11 [2.71] .24 [6.22] .16 [4.02] .33 [8.42] 2(VS-VD) RBIAS= ID .05 [1.27] .02 [.60] 726 Palomar Ave., Sunnyvale, CA 94085 Phone: (800) SMI-MMIC 4 http://www.stanfordmicro.com EDS-101994 Rev B Preliminary CGA-6618 Dual GaAs HBT Amplifier Package Outline Drawing TOP VIEW 8 7 6 5 BOTTOM VIEW Date Code CGA 6618 1 2 3 4 .078 [1.969] .155 [3.937] .236 [5.994] .061 [1.549] .194 [4.93] EXPOSED PAD .035 [.889] .045 [1.143] .050 [1.27] .016 [.406] .061 [1.549] .008 [.203] .058 [1.473] .013 [.33] x 45 .008 .194 [4.928] .003 [.076] SEATING PLANE SEE DETAIL A .155 [3.937] SIDE VIEW END VIEW PARTING LINE DETAIL A .025 5 Caution: ESD sensitive Appropriate precautions in handling, packaging and testing devices must be observed. Part Number Ordering Information Part Number CGA-6618 Devices Per Reel 500 Reel Size 7" Note: Parts need to be baked prior to use as discussed in application note EAN-101472 (Special handling information for Exposed Pad TM SOIC-8 products) to ensure no moisture is trapped in the encapsulated package. In production, this baking procedure is not necessary if parts are used within 24 hours of opening the sealed shipping materials. 726 Palomar Ave., Sunnyvale, CA 94085 Phone: (800) SMI-MMIC 5 http://www.stanfordmicro.com EDS-101994 Rev B |
Price & Availability of CGA-6618 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |