View MN39260FH_766493.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CCD Area Image Sensor
MN39260FH
4.5 mm (type-1/4) 810k-pixel CCD Area Image Sensor
Overview
The MN39260FH is a 4.5 mm (type-1/4) interline transfer CCD (IT-CCD) solid state image sensor device. This device uses photodiodes in the optoelectric conversion section and CCDs for signal readout. The electronic shutter function has made an exposure time of 1/10 000 seconds possible. Further, this device has the features of high sensitivity, low noise, broad dynamic range, and low smear. This device has a total of 802 579 pixels (1 007 horizontal x 797 vertical) and provides stable and clear images with a resolution of 600 horizontal TV-lines and 420 vertical TV-lines. Part Number Size System Color or B/W PAL Color
(Top View)
Pin Assignments
V4 V3 V2 V1 GND TEST VDD
1 2 3 4 5 6 7
14 13 12 11 10 9 8
PT Sub H2 H1 R GND VO
MN39260FH 4.5 mm (type-1/4)
Features
* Effective pixel number 962 (horizontal) x 774 (vertical) * High sensitivity * Broad dynamic range * Low smear * Electronic shutter
Applications
* Camcorders * FA, OA cameras
Publication date: September 2001
SMD00004BEC
1
MN39260FH
Block Diagram
(4 columns OB + 962 columns valid area + 41 columns OB)
1
(2 dummies + OB11 + valid area 774 + OB12 )
Sub
13
V4 2 V3 3 4
V2
Photo diode
VO VDD GND
8 7 9
Output section
Vertical shift register
V1
Horizontal register (one dummy at the front, no dummy at the back)
GND 6 TEST *1 14 PT
5
10
11 H1
Description Pin No. Symbol 8 9 10 11 12
*1
R
*1 : TEST pin must be left open, because the pin outputs CCD internal bias voltage.
Pin Descriptions
Pin No. Symbol 1 2 3 4 5 6 7 V4 V3 V2 V1 GND TEST VDD Description Video output GND Reset pulse (RG) Horizontal register clock pulse 1 Horizontal register clock pulse 2 Substrate P-well for protection circuit Vertical shift register clock pulse 4 Vertical shift register clock pulse 3 Vertical shift register clock pulse 2 Vertical shift register clock pulse 1 GND TEST pin (OPEN) Power supply VO GND R H1 H2 Sub PT
13 14
Note) *1: TEST pin must be left open, because the pin outputs CCD internal bias voltage.
Device Parameter (H x V)
Parameter Pixel number
*1
Value 962 x 774 3.703 7 x 2.709 0 3.85 x 3.50
Unit pixel mm2 m2
Image sensing block dimension Pixel dimension
Note) *1: OB columns are not included.
2
SMD00004BEC
H2
12
MN39260FH
Absolute Maximum Ratings and Operating Conditions
Absolute maximum rating Parameter VDD VPT
*3, 4
Operating condition Min 14.5 -7.5 3.0 Typ 15.0 -7.0 0 3.3 Max 15.5 -6.5 3.6 Unit V V V V V 3.3 0 3.3 0 3.6 0.2 3.6 0.2 V V V V V 22.0 15.0 0 -7.0 0 -7.0 15.0 0 -7.0 0 -7.0 25 23.0 15.5 0.05 -6.5 0.05 -6.5 15.5 0.05 -6.5 0.05 -6.5 V V V V V V V V V V V C C
Lower limit - 0.2 -10.0 - 0.2 - 0.2 - 0.2
Upper limit 18 0.2
GND VR VH1 VH2 VSub
*2 *1
(Reference voltage) High-Low Bias High Low High Low 8 8 8
(Supplied internally) 3.0 - 0.2 3.0 - 0.2 (Supplied internally) 35 18 15 18 15 60 80 21.0 14.5 - 0.05 -7.5 - 0.05 -7.5 14.5 - 0.05 -7.5 - 0.05 -7.5 -9 -9 -9 -9 -10 -30
VSub VV1
*3, 4
High Middle Low
VV2 VV3
*3, 4
Middle Low
*3, 4
High Middle Low
VV4
*3, 4
Middle Low
Operating temperature Storage temperature
SMD00004BEC
3
MN39260FH
Absolute Maximum Ratings and Operating Conditions (continued)
Note) 1. Standard photo detecting condition Standard photo detecting condition stands for detecting image with a light source of color temperature of 2 856K, luminance of 1 050 cd/m2, and using a color temperature conversion filter LB-40 (HOYA), infrared cut filter CAW-500S with thickness 2.5 mm for a light path and with F8 lens aperture. The quantity of the incidental light to a photo-detecting surface under the above condition is defined as the standard quantity of light. 2. *1: VSub when using electronic shutter function
VSub H VSub (V) VSub L GND VSub (V) (Supplied internally)
* Sub pulse generates once every 1 V period.
*2: VSub supplied internally is the voltage suppressing the blooming generation at x500 light quantity relative to the standard light quantity. *3: Relation between VPT and VVL Set VPT under the following condition against VL of a vertical transfer clock waveform. VPT VL (VV1L to VV4L) - 0.2 < VV - VPT < 24.5 (V) *4: Absolute maximum ratings
Optical Characteristics
Parameter Carrier saturation output Sensitivity Vertical smear Symbol Sc So Sm J chart J chart F1.4, 1/32 ND 1/10 V chart, F1.4 Conditions Min 500 80 Typ 110 Max 0.01 Unit mV mV %
Note) The above-mentioned characteristics are the values on driving the device for the imaging stabilizer mode (1/60 seconds accumulation).
4
SMD00004BEC
MN39260FH
Timing Diagram
* High speed pulse timing
H1
50%
50%
50%
27.8 ns 3 ns
CCD output
R
50%
50%
1 ns 3 ns
10 ns 13.9 ns
Clamp pulse (DS1)
50%
50%
3 ns 3 ns
13.9 ns 3 ns
Sampling pulse (DS2)
50%
50%
4 ns 3 ns
13.9 ns 3 ns
SMD00004BEC
5
MN39260FH
Timing Diagram (continued)
* Rise time and fall time of each pulse
V1 , V3
0.9
0.9
0.1 0.9
0.1 0.9
0.1 300 ns V2 , V4 300 ns 300 ns
0.1 300 ns
0.9
0.9
0.1 300 ns H1 , H2 0.9 0.9 R
0.1 300 ns
0.9
0.9
0.1 8 ns
0.1 8 ns
0.1 6 ns
0.1 6 ns
6
SMD00004BEC
MN39260FH
Color Filter Arrays on CCD
774 773 Cy Mg Ye G Cy Mg Ye G Cy Mg Ye G Cy Mg Ye G Cy Mg Ye G
8 7 6 5 4 3 2 1
Cy G Cy Mg Cy G Cy Mg 1
Ye Mg Ye G Ye Mg Ye G 2
Cy G Cy Mg Cy G Cy Mg 3
Ye Mg Ye G Ye Mg Ye G 4
Cy G Cy Mg Cy G Cy Mg 5
Ye Mg Ye G Ye Mg Ye G 6
Cy G Cy Mg Cy G Cy Mg 7
Ye Mg Ye G Ye Mg Ye G 8
Cy G Cy Mg Cy G Cy Mg
Ye Mg Ye G Ye Mg Ye G
961 962
Graph of Characteristics
CCD color filter spectral characteristics
1.2
Ye 1.0
0.8
Relative sensitivity
0.6 Cy Gr
0.4 Mg
0.2
0 400
450
500
550
600
650
700
750
800
Wavelength (nm) SMD00004BEC
7
MN39260FH
Package Dimensions (unit: mm)
* WDIP014-P-0400H
10.000.08 9.000.10 5.000.08 14 8
5.000.08 9.000.10 10.000.08
Reference plane
0.015
Valid pixel center
(0.60)
3.500.20 1.300.10
(1.19)
1.27
0.300.05
0.3 M
1
(2.50)
7
2-R0.40 (depth 0.30)
14
8
1. The center of the package is equal to the center of the effective pixel area. 2. The rotation angle of the effective pixel area: up to 1.0 degree 3. The distance from the bottom face of the package to the surface of the effective pixel area: 1.41 mm 0.1 mm 4. The tilt of the effective pixel area for the bottom face of the package: up to 25 m 5. Thickness of seal glass is 0.7 mm 0.1 mm, and the refractive index is 1.50. 6. Package weight: 0.55 g (typ.)
8
(2.50)
SMD00004BEC
3.30.15
(1.30)
0.250.05
(0.7)
1
7
10.160.25
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd.
2002 JUL

▲Up To Search▲

Price & Availability of MN39260FH

	To Download MN39260FH Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .