View HNC1-25P-12DSL_823996.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

2.5mm Pitch Connector for Discrete Wire Connection
HNC Series
sFeatures
1. Full Lock Mechanism
The connector is equipped with the full lock mechanism so as not be removed, unless locks are reset on both sides. This mechanism is activated effectively to prevent cable hooking or mis-insertion.
2. Thin Type Connector
Mounting height when the connector is used at the right angle :
4.5mm
3. Mechanism to Prevent Mis-insertion
This thin type connector is equipped with the mechanism to prevent misinsertion. Thickness 4.5mm
4. Tin Plating and Gold Plating Variation
Two kinds of tin plating and gold plating types are available, and can be chosen according to application. The tin plating is also set to a light operating touch.
Mechanism to prevent false-insertion Full lock mechanism
sApplications
Various business equipment, financial terminals
B139
sProduct Specifications
AWG 22 : 3A Current rating Rating (Note1) AWG 24 : 3A AWG 26 : 2A AWG 28 : 1A AWG 30 : 0.5A Voltage rating Item 1. Insulation Resistance 2. Withstanding voltage 3. Contact Resistance 5. Vibration 1000M ohms min. No flashover or insulation breakdown. 30m ohms Max No electrical discontinuity of 1s or more 250V AC Specification 500V DC 1000V AC/1 minute 1A Measure at the square steel pin of 0.6350.002mm Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. (-25c: 30 minutes 5 to 35c: 10 minutes (-85c: 30 minutes 5 to 35c: 10 minutes) 5 cycles Tin plating : 30 cycles Gold plating : 50 cycles Flow: 250c for 5 seconds Manual soldering: 300c for 2 seconds Operating Temperature Range Operating Moisture Range Storage Temperature Range Storage Moisture Range -25 to +85c (Note2) -40 to 80% -10 to +60c (Note3) -40 to 70% (Note3)
Condition
4. Insertor/Extraction Force 0.4N (40gf) min.,4.4N (450gf) max.
6. Humidity (Steady state) Contact resistance: 10m ohms max.Insulation resistance: 1000M ohms min. 96 hours at temperature of 40c and humidity of 90% to 95% 7. Temperature Cycle Contact resistance: 10m ohms max:Insulation resistance: 1000M ohms min.
8. Durability (Mating/un-mating) Contact resistance: 20m ohms max. 9. Resistance to Soldering heat No deformation of components affecting performance.
Note 1: The rated current will be changed according to cable sizes for use. The header rating only t is 3A. Note 2: Includes temperature rise caused by current flow. Note 3: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation.
sMaterial
Product Crimping Socket Contact Pin Header Part Insulator Contact Insulator Contact Material Polyamide Phosphor Copper Polyamide Brass Finish Black Tin plated or gold plated Black Tin plated or gold plated Remarks UL94V-0 ----- UL94V-0 -----
sOrdering Information
qCrimping Plug
HNC 2 - 2.5 P - * DSL
q q Series Name w Series No. e Contact Pitch r Connector Type S : Socket P : Pin Header w : HNC : 2, 1 : 2.5mm e r t y t Number of Contacts : 2 to 16, 18, 20 y Contact Type None : Crimping socket DS : Straight DSL : Right angle
qContact
HNC2 - 2.5S - C - A
q q Type: 2.5mm pitch socket w Packaging Type C : Reel PC : Bag w e e Applicable cable size A : AWG22 to 26 B : AWG26 to 30
B140
sCrimping Socket
[Figure 1]
[Figure 2]
Unit: mm Part Number HNC2-2.5S- 2(**) HNC2-2.5S- 3(**) HNC2-2.5S- 4(**) HNC2-2.5S- 5(**) HNC2-2.5S- 6(**) HNC2-2.5S- 7(**) HNC2-2.5S- 8(**) HNC2-2.5S-10(**) HNC1-2.5S-12(**) CL No. 218-0011-1-** 218-0022-8-** 218-0039-0-** 218-0027-1-** 218-0042-5-** 218-0030-6-** 218-0014-0-** 218-0017-8-** 218-0008-7-** Number of Contacts 2 3 4 5 6 7 8 10 12 A 12.4 14.9 17.4 19.9 22.4 24.9 27.4 32.4 37 B 6 8.5 11 13.5 16 18.5 21 26 31 C 2.5 5 7.5 10 12.5 15 17.5 22.5 27.5 Figure 2 Figure 1 Dimensions [Specific No.] -* *, (* *) Blank :Bag packaging
Figure 1 15 44.9 38.5 35 HNC2-2.5S-15(**) 218-0045-3-** Note1: Please order a quantity multiplied by 100 pcs. (Not per bag, but per pcs.) Note2: The series name of 12 contacts connector is HNC1, and partially will be changed in the style.
B141
sStraight Pin Header
[Figure 3]
0.1 qBoard Through-hole Diameter: o1.1+0
+
[Figure 4]
Unit: mm Part Number HNC2-2.5P- 2DS(**) HNC2-2.5P- 3DS(**) HNC2-2.5P- 4DS(**) HNC2-2.5P- 5DS(**) HNC2-2.5P- 6DS(**) HNC2-2.5P- 7DS(**) HNC2-2.5P- 8DS(**) HNC2-2.5P-10DS(**) HNC1-2.5P-12DS(**) CL No. 218-0012-4-** 218-0023-0-** 218-0040-0-** 218-0028-4-** 218-0043-8-** 218-0031-9-** 218-0015-2-** 218-0018-0-** 218-0009-0-** Number of Contacts 2 3 4 5 6 7 8 10 12 A 12.5 15 17.5 20 22.5 25 27.5 32.5 35.5 B 7.8 10.4 12.9 15.4 17.9 20.4 22.8 27.8 32.8 C 2.5 5 7.5 10 12.5 15 17.5 22.5 27.5 Specific No. Tin plating Blank Blank Blank Blank Blank Blank Blank Blank Blank Gold plating 02 02 01 02 01 02 02 02 02 01 Figure 4 Figure 3 Figure 3 Dimensions
40.4 35 Blank 15 45 HNC2-2.5P-15DS(**) 218-0046-6-** Note1: Please order a quantity multiplied by 100 pcs. (Not per bag, but per piece) Note2: The series name of the 12 contacts connector is HNC1 and the style will be partially changed.
B142
sRight Angle Pin Header
[Figure 5]
+0.1 qBoard Through-hole Diameter: o1.1+0
[Figure 6]
Unit: mm Part Number HNC2-2.5P- 2DSL(**) HNC2-2.5P- 3DSL(**) HNC2-2.5P- 4DSL(**) HNC2-2.5P- 5DSL(**) HNC2-2.5P- 6DSL(**) HNC2-2.5P- 7DSL(**) HNC2-2.5P- 8DSL(**) HNC2-2.5P-10DSL(**) HNC1-2.5P-12DSL(**) CL No. 218-0013-7-** 218-0024-3-** 218-0041-2-** 218-0029-7-** 218-0044-0-** 218-0032-1-** 218-0016-5-** 218-0019-3-** 218-0010-9-** Number of Contacts 2 3 4 5 6 7 8 10 12 A 12.5 15 17.5 20 22.5 25 27.5 32.5 35.5 B 7.8 10.4 12.9 15.4 17.9 20.4 22.8 27.8 32.8 C 2.5 5 7.5 10 12.5 15 17.5 22.5 27.5 Specific No. Tin plating Blank Blank Blank Blank Blank Blank Blank Blank Blank Gold plating 02 02 01 02 01 02 02 02 02 01 Figure 6 Figure 5 Figure 5 Dimensions
40.4 35 Blank 15 45 HNC2-2.5P-15DSL(**) 218-0047-9-** Note1: Please order a quantity multiplied by 100 pcs. (Not per bag, but per piece) Note2: The series name of the 12 contacts connector is HNC1 and the style will be partially changed.
B143
sCrimping Contact for Socket
qApplicable Cable (Tin Plated Annealing Copper Wire)
Conductor Size (Contact wire construction) Jacket Diameter AWG 22 (17pieces/0.16mm) AWG 24 (11pieces/0.16mm) AWG 26 (07pieces/0.16mm) AWG 28 (07pieces/0.127mm) AWG 30 (07pieces/0.1mm) O1.0 to O1.35mm O1.35 to O1.7mm
qRecommended Cable
UL1061, UL1007
qStrip Length
2.8 to 3.3mm
Note: If other cables are used instead of the applicable cable, please contact Hirose sales department.
Unit: mm Part Number HNC-2.5S-D-A(**) HNC-2.5S-C-A(**) HNC-2.5S-D-B(**) HNC-2.5S-C-B(**) CL No. 218-0037-5-** 218-0021-5-** 218-0038-8-** 218-0020-2-** Conductor Size Jacket Diameter A B Packaging Type Bag Reel Bag Reel Quantity 100 10,000 100 10,000 Blank 02 Specific No. Tin plating Gold plating
AWG 22 to 26 O1.35 to 1.7mm AWG 26 to 30 O1.0 to 1.35mm
1.8 2.6 1.8 2.6 1.5 1.7 1.5 1.7
sApplicable Crimping Tool
Type Applicator Press Main Unit Manual Crimping Tool Extraction Tool Part Number AP105-HNC CM105 TC-HNC-B TC-HNC-A DF1-C-PO CL No. 901-4502-0 901-0005-4 250-0005-7 250-0006-0 550-0177-7 Applicable Contact HNC-2.5S-C-A/HNC-2.5S-C-B ------------------------ HNC-2.5S-D-B HNC-2.5S-D-A HNC-2.5S-C-A/HNC-2.5S-C-B
Note: If a trouble has occurred due to tools which are not designated by Hirose, Hirose won't guarantee any product.
sApplication Pattern
B144
BPrecautions
1. Recommended Soldering Condition 2. Cleaning Condition 3. Connection Condition Flow: 250c for 3 seconds Manual soldering: 290c for 2 seconds Refer to Nylon Connector Use Hand book. Refer to Nylon Connector Use Hand book. qExtracting Crimping Contact To extract the crimping contact from the socket housing, observe the following extraction procedures. sExtraction Tool Tool Name: DF-C-PO(550-0177-7) can be used.
(1) Extraction Method As shown below in the figure, slightly pull the cable in the state where the DF1 extraction tool tip or the 0.5 to 0.7mm board has been inserted in the lance fixed slot, the contact can be easily removed. Note: If the lance is pressed excessively, the contact body may be deformed, which could result in contact failure. Therefore, be careful not to press the lance excessively.
(2) How to Adjust the Lance (Raise) To re-insert the terminal which is removed from the socket housing, use a sharp edge blade to raise the lance as shown below in the illustration, and then insert the contact. Note: Lance regeneration is effective only once.
B145

▲Up To Search▲

Price & Availability of HNC1-25P-12DSL

	To Download HNC1-25P-12DSL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .