 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| LM675 Power Operational Amplifier May 1996 LM675 Power Operational Amplifier General Description The LM675 is a monolithic power operational amplifier featuring wide bandwidth and low input offset voltage making it equally suitable for AC and DC applications The LM675 is capable of delivering output currents in excess of 3 amps operating at supply voltages of up to 60V The device overload protection consists of both internal current limiting and thermal shutdown The amplifier is also internally compensated for gains of 10 or greater Y Y Y Y Y Y Y Y 1 mV typical offset voltage Short circuit protection Thermal protection with parole circuit (100% tested) 16V - 60V supply range Wide common mode range Internal output protection diodes 90 dB ripple rejection Plastic power package TO-220 Features Y Y Y Y Y Applications Y Y Y Y Y 3A current capability AVO typicaly 90 dB 5 5 MHz gain bandwidth product 8 V ms slew rate Wide power bandwidth 70 kHz High performance power op amp Bridge amplifiers Motor speed controls Servo amplifiers Instrument systems Connection Diagram TO-220 Power Package (T) Typical Applications Non-Inverting Amplifier TL H 6739 - 1 Front View Order Number LM675T See NS Package T05D The tab is internally connected to pin 3 ( b VEE) TL H 6739 - 2 C1996 National Semiconductor Corporation TL H 6739 RRD-B30M56 Printed in U S A http www national com Absolute Maximum Ratings If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications Supply Voltage Input Voltage g30V Operating Temperature Storage Temperature Junction Temperature Power Dissipation (Note 1) Lead Temperature (Soldering 10 seconds) ESD rating to be determined 0 C to a 70 C b 65 C to a 150 C b VEE to VCC 150 C 30W 260 C Electrical Characteristics VS e g25V Parameter Supply Current Input Offset Voltage Input Bias Current Input Offset Current Open Loop Gain PSRR CMRR Output Voltage Swing Offset Voltage Drift Versus Temperature Offset Voltage Drift Versus Output Power Output Power Gain Bandwidth Product Max Slew Rate Input Common Mode Range TA e 25 C unless otherwise specified Conditions Typical 18 1 02 50 90 90 90 g21 Tested Limit 50 (max) 10 (max) 2 (max) 500 (max) 70 (min) 70 (min) 70 (min) g18 (min) Units mA mV mA nA dB dB dB V mV C mV W POUT e 0W VCM e 0V VCM e 0V VCM e 0V RL e % X DVS e g5V VIN e g20V RL e 8X RS k 100 kX 25 25 THD e 1% fO e 1 kHz RL e 8X fO e 20 kHz AVCL e 1000 25 55 8 g22 20 W MHz V ms g20 (min) V Note 1 Assumes TA equal to 70 C For operation at higher tab temperatures the LM675 must be derated based on a maximum junction temperature of 150 C Typical Applications (Continued) Generating a Split Supply From a Single Supply VS e g8V x g30V TL H 6739 - 3 http www national com 2 Typical Performance Characteristics THD vs Power Output Input Common Mode Range vs Supply Voltage Supply Current vs Supply Voltage PSRR vs Frequency Device Dissipation vs Ambient Temperature Current Limit vs Output Voltage i INTERFACE e 1 C W See Application Hints VS e g25V IB vs Supply Voltage Output Voltage Swing vs Supply Voltage TL H 6739 - 4 3 http www national com http www national com 4 TL H 6739 - 5 Schematic Diagram Application Hints STABILITY The LM675 is designed to be stable when operated at a closed-loop gain of 10 or greater but as with any other high-current amplifier the LM675 can be made to oscillate under certain conditions These usually involve printed circuit board layout or output input coupling When designing a printed circuit board layout it is important to return the load ground the output compensation ground and the low level (feedback and input) grounds to the circuit board ground point through separate paths Otherwise large currents flowing along a ground conductor will generate voltages on the conductor which can effectively act as signals at the input resulting in high frequency oscillation or excessive distortion It is advisable to keep the output compensation components and the 0 1 mF supply decoupling capacitors as close as possible to the LM675 to reduce the effects of PCB trace resistance and inductance For the same reason the ground return paths for these components should be as short as possible Occasionally current in the output leads (which function as antennas) can be coupled through the air to the amplifier input resulting in high-frequency oscillation This normally happens when the source impedance is high or the input leads are long The problem can be eliminated by placing a small capacitor (on the order of 50 pF to 500 pF) across the circuit input Most power amplifiers do not drive highly capacitive loads well and the LM675 is no exception If the output of the LM675 is connected directly to a capacitor with no series resistance the square wave response will exhibit ringing if the capacitance is greater than about 0 1 mF The amplifier can typically drive load capacitances up to 2 mF or so without oscillating but this is not recommended If highly capacitive loads are expected a resistor (at least 1X) should be placed in series with the output of the LM675 A method commonly employed to protect amplifiers from low impedances at high frequencies is to couple to the load through a 10X resistor in parallel with a 5 mH inductor CURRENT LIMIT AND SAFE OPERATING AREA (SOA) PROTECTION A power amplifier's output transistors can be damaged by excessive applied voltage current flow or power dissipation The voltage applied to the amplifier is limited by the design of the external power supply while the maximum current passed by the output devices is usually limited by internal circuitry to some fixed value Short-term power dissipation is usually not limited in monolithic operational power amplifiers and this can be a problem when driving reactive loads which may draw large currents while high voltages appear on the output transistors The LM675 not only limits current to around 4A but also reduces the value of the limit current when an output transistor has a high voltage across it When driving nonlinear reactive loads such as motors or loudspeakers with built-in protection relays there is a possibility that an amplifier output will be connected to a load whose terminal voltage may attempt to swing beyond the power supply voltages applied to the amplifier This can cause degradation of the output transistors or catastrophic failure of the whole circuit The standard protection for this type of failure mechanism is a pair of diodes connected between the output of the amplifier and the supply rails These are part of the internal circuitry of the LM675 and needn't be added externally when standard reactive loads are driven THERMAL PROTECTION The LM675 has a sophisticated thermal protection scheme to prevent long-term thermal stress to the device When the temperature on the die reaches 170 C the LM675 shuts down It starts operating again when the die temperature drops to about 145 C but if the temperature again begins to rise shutdown will occur at only 150 C Therefore the device is allowed to heat up to a relatively high temperature if the fault condition is temporary but a sustained fault will limit the maximum die temperature to a lower value This greatly reduces the stresses imposed on the IC by thermal cycling which in turn improves its reliability under sustained fault conditions This circuitry is 100% tested without a heat sink Since the die temperature is directly dependent upon the heat sink the heat sink should be chosen for thermal resistance low enough that thermal shutdown will not be reached during normal operaton Using the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of any power semiconductor POWER DISSIPATION AND HEAT SINKING The LM675 should always be operated with a heat sink even though at idle worst case power dissipation will be only 1 8W (30 mA c 60V) which corresponds to a rise in die temperature of 97 C above ambient assuming ijA e 54 C W for a TO-220 package This in itself will not cause the thermal protectioncircuitrytoshutdowntheamplifierwhenoperatingat roomtemperature butamere0 9Wofadditionalpowerdissipation will shut the amplifier down since TJ will then increase from 122 C (97 C a 25 C) to 170 C In order to determine the appropriate heat sink for a given application the power dissipation of the LM675 in that application must be known When the load is resistive the maximum average power that the IC will be required to dissipate is approximately PD (MAX) VS2 a PQ 2q2RL where VS is the total power supply voltage across the LM675 RL is the load resistance and PQ is the quiescent power dissipation of the amplifier The above equation is only an approximation which assumes an ``ideal'' class B output stage and constant power dissipation in all other parts of the circuit As an example if the LM675 is operated on a 50V power supply with a resistive load of 8X it can develop up to 19W of internal power dissipation If the die temperature is to remain below 150 C for ambient temperatures up to 70 C the total junction-to-ambient thermal resistance must be less than 150 C b 70 C e42 C W 19W Using iJC e 2 C W the sum of the case-to-heat sink interface thermal resistance and the heat-sink-to-ambient 5 http www national com Application Hints (Continued) thermal resistance must be less than 2 2 C W The case-toheat-sink thermal resistance of the TO-220 package varies with the mounting method used A metal-to-metal interface will be about 1 C W if lubricated and about 1 2 C W if dry If a mica insulator is used the thermal resistance will be about 1 6 C W lubricated and 3 4 C W dry For this example we assume a lubricated mica insulator between the LM675 and the heat sink The heat sink thermal resistance must then be less than 42 C Wb2 C Wb16 C We06 C W This is a rather large heat sink and may not be practical in some applications If a smaller heat sink is required for reasons of size or cost there are two alternatives The maximum ambient operating temperature can be restricted to 50 C (122 F) resulting in a 1 6 C W heat sink or the heat sink can be isolated from the chassis so the mica washer is not needed This will change the required heat sink to a 1 2 C W unit if the case-to-heat-sink interface is lubricated The thermal requirements can become more difficult when an amplifier is driving a reactive load For a given magnitude of load impedance a higher degree of reactance will cause a higher level of power dissipation within the amplifier As a general rule the power dissipation of an amplifier driving a 60 reactive load will be roughly that of the same amplifier driving the resistive part of that load For example some reactive loads may at some frequency have an impedance with a magnitude of 8X and a phase angle of 60 The real part of this load will then be 8X c cos 60 or 4X and the amplifier power dissipation will roughly follow the curve of power dissipation with a 4X load Typical Applications (Continued) Non-Inverting Unity Gain Operation R 1C t R1 s 1 2q500 kHz RS a R2 10 AV(DC) e 1 UNITY GAIN BANDWIDTH j 50 kHz TL H 6739 - 6 Inverting Unity Gain Operation R 1C t R1 s 1 2q500 kHz R2 10 AV(DC) e b 1 UNITY GAIN BANDWIDTH j 50 kHz TL H 6739 - 7 http www national com 6 Typical Applications (Continued) Servo Motor Control TL H 6739 - 8 High Current Source Sink IOUT e VIN c 2 5 amps volt i e IOUT e 1A when VIN e 400 mV Trim pot for max ROUT TL H 6739 - 9 7 http www national com LM675 Power Operational Amplifier Physical Dimensions inches (millimeters) unless otherwise noted TO-220 Power Package (T) Order Number LM675T NS Package T05D LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user National Semiconductor Corporation 1111 West Bardin Road Arlington TX 76017 Tel 1(800) 272-9959 Fax 1(800) 737-7018 2 A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness http www national com National Semiconductor Europe Fax a49 (0) 180-530 85 86 Email europe support nsc com Deutsch Tel a49 (0) 180-530 85 85 English Tel a49 (0) 180-532 78 32 Fran ais Tel a49 (0) 180-532 93 58 Italiano Tel a49 (0) 180-534 16 80 National Semiconductor Hong Kong Ltd 13th Floor Straight Block Ocean Centre 5 Canton Rd Tsimshatsui Kowloon Hong Kong Tel (852) 2737-1600 Fax (852) 2736-9960 National Semiconductor Japan Ltd Tel 81-043-299-2308 Fax 81-043-299-2408 National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications |
Price & Availability of LM675
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |