 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MN102L360C Type ROM (x8-bit / x 16-bit) x RAM (x 8-bit / x 16-bit) x Package Minimum Instruction Execution Time Interrupts MN102L360C External 5K LQFP128-P-1818C *Lead-free 100 ns (at 4.5 V to 5.5 V, 20 MHz) * RESET * Watchdog * Timer counter 0 to 5 * Fixed-length serial ch.0,1 transmission * Fixed-length serial ch.0,1 reception * Timer counter 6 to 7 * Timer counter 6 to 7 compare capture A * Timer counter 6 to 7 compare capture B * ATC transfer finish * External 0 to 7 * Serial ch.0,1 transmission * Serial ch.0,1 reception * NMI pin * A/D conversion finish Timer counter 0: 8-bit x 1 (timer output, event count) Clock source ********************* 1/1, 1/128 of system clock frequency; 1/4 of low speed clock frequency; external clock Interrupt source **************** timer counter 0 underflow Timer counter 1: 8-bit x 1 (timer output, even count, A/D conversion start) Clock source ********************* system clock; 1/4 of low speed clock frequency; external clock; timer counter 0 output Interrupt source **************** timer counter 1 underflow Timer counter 2 to 3: 8-bit x 1 (timer output, event count, UART baud rate generation) Clock source ********************* system clock; external clock; timer counter 0 output; timer counter 1, 2 output Interrupt source **************** timer counter 2, 3 underflow Timer counter 4,5: 8-bit x 1 (timer output, event count) Clock source ********************* 1/4 of low speed clock frequency; external clock; timer counter 0 output; timer counter 3, 4 output Interrupt source **************** timer counter 4, 5 underflow Timer counter 6, 7: 16-bit x 1 (timer output, event count, input capture, output compare, PWM output, 2-phase encoder input) Clock source ********************* system clock; external clock; timer counter 4, 5 output Interrupt source **************** coincidence with compare capture A or at capture; coincidence with compare capture B or at capture; underflow of timer counter 6, 7 Connectable timer counter 0 to 5 Timer Counter Serial Interface Serial 0: 7, 8-bit x 1 (common use with UART, transfer direction of MSB/LSB selectable) Clock source ********************* 1/16 of timer counter 2 frequency; 1/16 of timer counter 3 frequency; external clock; 1/2 of timer counter 2 frequency I2C mode (master transmission/reception is possible in the single master system.) Serial 1: 7, 8-bit x 1 (common use with UART, transfer direction of MSB/LSB selectable) Clock source ********************* 1/16 of timer counter 2 frequency; 1/16 of timer counter 3 frequency; external clock; 1/2 of timer counter 3 frequency I2C mode (master transmission/reception is possible in the single master system.) Fixed-length serial 0: 8-bit x 1 Clock source ********************* external clock Sending direction ************* LSB Fixed-length serial 1: 8-bit x 1 Clock source ********************* external clock Sending direction ************* LSB I/O Pins A/D Inputs I/O 83 * Common use: 8 (by 4 bits), 75 (by bit) 8-bit x 8-ch. (with S/H) MAE00008DEM 1 MN102L360C D/A Outputs PWM Notes Electric Characteriatics Supply current 8-bit x 2-ch. 16-bit x 2-ch. Burst ROM interface support, ATC ( between serial 0 ch and built-in RAM) support Limit Parameter Symbol Condition min Operating supply current VI = VDD or VSS, output open IDDopr f = 20 MHz , VDD = 5.0 V Supply current at STOP Pin with pull-up resistor is open IDDS all other input pins and Hi-Z state input/output Supply current at HALT pins are simultaneously applied VDD or VSS level IDDH f = 20 MHz , VDD = 5.0 V, output open (Ta = -40C to +85C , VDD = 5.0 V , VSS = 0 V) 30 mA 50 A 75 mA typ max Unit Pin Assignment SBO1,P75 SBI1,P74 SBT1,P73 SBO0,P72 SBI0,P71 SBT0,P70 VDD AN7,PO7 AN6,PO6 AN5,PO5 AN4,PO4 VSS AN3,P97 AN2,P96 AN1,P95 AN0,P94 VDD TM7IC,P93 TM7IOB,P92 TM7IOA,P91 TM6IC,P90 TM6IOB,P87 TM6IOA,P86 SFI1,PC4 SFT1,PC3 SFO0,PC2 SFI0,PC1 SFT0,PC0 VDD NMI 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 PB3 PB4 PB5 PB6 PB7 VDD P60,WAIT *P61,RE P62,WEL P63,WEH *P50,CS0 P51,CS1 P52,CS2 P53,CS3 P54,BREQ P55,BRACK P56,ALE,ALE,BSTRE * *P57,WORD VSS P20,A00 P21,A01 P22,A02 P23,A03 VDD SYSCLK VSS XI XO VDD OSCI OSCO MODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PC5,SFO1 PC6,DA0 PC7,DA1 VSS PA0,IRQ0 PA1,IRQ1 PA2,IRQ2 PA3,IRQ3 PA4,IRQ4 *PA5,ADSEP RST VDD(VPP) P00,D00,AD00 P01,D01,AD01 P02,D02,AD02 P03,D03,AD03 P04,D04,AD04 P05,D05,AD05 P06,D06,AD06 P07,D07,AD07 VSS *P10,D08,AD08 *P11,D09,AD09 *P12,D10,AD10 *P13,D11,AD11 *P14,D12,AD12 *P15,D13,AD13 *P16,D14,AD14 *P17,D15,AD15 PB0 PB1 PB2 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 MN102L360C 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 PD3,IRQ7 PD2,IRQ6 PD1,IRQ5 PD0 TM5IO,P85 TM4IO,P84 TM3IO,P83 TM2IO,P82 TM1IO,P81 TM0IO,P80 A23,WDOUT,P47 A22,STOP,P46 A21,P45 A20,P44 VSS A19,P43 A18,P42 A17,P41 A16,P40 A15,P37 A14,P36 A13,P35 A12,P34 VDD A11,P33 A10,P32 A09,P31 A08,P30 A07,P27 A06,P26 A05,P25 A04,P24 LQFP128-P-1818C * Port unusable *Lead-free See the next page for support tool. MAE00008DEM 2 Support Tool In-circuit Emulator EPROM Built-in Type PX-ICE102L00 + PX-PRB102L36-LQFP128-P-1818C Type ROM (x 8-bit / x 16-bit) RAM (x 8-bit / x 16-bit) Minimum instruction execution time Package MN102LP36Z 128 K 10 K 100 ns (at 4.5 V to 5.5 V, 20 MHz) LQFP128-P-1818C *Lead-free 3 MAE00008DEM MN102L360C MAE00008DEM 4 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2002 JUL |
Price & Availability of MN102L360C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |