 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MICROCIRCUIT DATA SHEET MNLM158A-X REV 3A0 Original Creation Date: 08/14/95 Last Update Date: 10/15/98 Last Major Revision Date: 03/16/98 LOW POWER, DUAL OPERATIONAL AMPLIFIER General Description The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of magnitude of the power supply voltage. Application areas include transducer amplifiers, dc gain blocks and all the conventional op amp circuits which now can be more easily implemented in single power supply systems. For example, the LM158 series can be directly operated off of the standard +5V DC power supply voltage which is used in digital systems and will easily provide the required interface electronics without requiring the additional + 15V DC power supplies. Industry Part Number LM158 NS Part Numbers LM158AH-QMLV*** LM158AH-SMD* LM158AH/883 LM158AJ-QMLV**** LM158AJ/883** Prime Die LM158 Controlling Document See Features Page Processing MIL-STD-883, Method 5004 Subgrp Description 1 2 3 4 5 6 7 8A 8B 9 10 11 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 Quality Conformance Inspection MIL-STD-883, Method 5005 1 MNLM158A-X REV 3A0 MICROCIRCUIT DATA SHEET Features - SMD : 5962-8771002GA*, PA**, VGA***, VPA**** 2 MNLM158A-X REV 3A0 MICROCIRCUIT DATA SHEET (Absolute Maximum Ratings) (Note 1) Supply Voltage, V+ 32Vdc Differential Input Voltage 32Vdc Input Voltage -0.3Vdc to +32Vdc Power Dissipation (Note 2) 830 mW Output Short-Circuit to GND (Note 3) (One Amplifier) V+ < 15Vdc and TA = 25 C Maximum Junction Temperature Input Current (Vin < -0.3Vdc) (Note 4) 50mA Operating Temperature Range -55 C to +125 C Storage Temperature Range -65 C to +150 C Lead Temperature J-Pkg (Soldering, 10 seconds) H-Pkg (Soldering, 10 seconds) Thermal Resistance ThetaJA H-Pkg (Still Air) (500LF/Min Air Flow) J-Pkg (Still Air) (500LF/Min Air Flow) ThetaJC H-Pkg J-Pkg ESD Tolerance (Note 5) 260 C 300 C Continuous 150 C 155 80 132 81 C/W C/.W C/W C/W 42 C/W 23 C/W 250V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. Short circuits from ther output to V+ from Vdc, can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15Vdc, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. Note 2: Note 3: 3 MNLM158A-X REV 3A0 MICROCIRCUIT DATA SHEET (Continued) Note 4: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward baised and thereby a acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater that -0.3Vdc (at 25C). Human body model, 1.5 K ohms in series with 100 pF. Note 5: 4 MNLM158A-X REV 3A0 MICROCIRCUIT DATA SHEET Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: All voltages referenced to device ground. SYMBOL Icc PARAMETER Power Supply Current CONDITIONS V+ = 5V, Rl = 100K, Vo = 1.4V V+ = 30V, Rl = 100K, Vo = 1.4V NOTES PINNAME MIN MAX 1.2 3 4 Voh Output Voltage High V+ = 30V, Rl = 2K Ohms V+ = 30V, Rl = 10K Ohms Vol Output Voltage Low V+ = 30V, Rl = 10K Ohms 26 27 40 100 V+ = 30V, Isink = 1uA 40 100 V+ = 5V, Rl = 10K Ohms 40 100 Isink Output Sink Current V+ = 15V, Vout = 200mV, Vin = 65 mV V+ = 15V, Vout = 2V, Vin = 65mV 12 10 5 Isource Output Source Current Short Circuit Current Input Offset Voltage V+ = 15V, Vin = 65mV, Vout = 2V -20 -10 Ios Vio V+ = 5V, Vout = 0V V+ = 30V, Vcm = 0V, Rs = 50 Ohms, Vo = 1.4V V+ = 30V, Vcm = 28V, Rs = 50 Ohms, Vo = 1.4V V+ = 5V, Vcm = 0V, Rs = 50 Ohms, Vo = 1.4V V+ = 30V, Vcm = 28.5V, Rs = 50 Ohms,Vo = 1.4V CMRR Iib+ Common Mode Rejection Ratio Input BIas Current V+ = 30V, Vin = 0V to 28.5V, Rs = 50 Ohms V+ = 5V, Vcm = 0V -60 -2 -4 -4 -2 -4 -2 70 -50 -100 -1 -1 2 4 4 2 4 2 UNIT mA mA mA V V mV mV mV mV mV mV uA mA mA mA mA mA mV mV mV mV mV mV dB nA nA SUBGROUPS 1, 2, 3 1 2, 3 1, 2, 3 1, 2, 3 1 2, 3 1 2, 3 1 2, 3 1 1 2, 3 1 2, 3 1 1 2, 3 2, 3 1 2, 3 1 1 1 2, 3 5 MNLM158A-X REV 3A0 MICROCIRCUIT DATA SHEET Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: All voltages referenced to device ground. SYMBOL IibPARAMETER Input BIas Current Input Offset Current Power Supply Rejection Ratio Common Mode Voltage Range Differential Input Voltage Large Signal Gain V+ = 15V, Rl = 2K Ohms, Vo = 1V to 11V CONDITIONS V+ = 5V, Vcm = 0V NOTES PINNAME MIN -50 -100 Iio V+ = 5V, Vcm = 0V -10 -30 PSRR Vcm V+ = 5V to 30V, Vcm = 0V V+ = 30V 1 1 Vdiff Avs 2 50 25 65 28.5 28.0 32 MAX -1 -1 10 30 UNIT nA nA nA nA dB V V V SUBGROUPS 1 2, 3 1 2, 3 1 1 2, 3 1, 2, 3 V/mV 4 V/mV 5, 6 DC PARAMETERS: DRIFT VALUES (The following conditions apply to all the following parameters, unless otherwise specified.) DC: All voltages referenced to device ground. "Delta calculations performed on Jan "S" and "QMLV" devices at Group B, Subgroup 5 only." Vio Input Offset Voltage V+ = 30V, Vcm = 0V, Rs = 50 Ohms, Vo = 1.4V V+ = 30V, Vcm = 28V, Rs = 50 Ohms, Vo = 1.4V V+ = 5V, Vcm = 0V, Rs = 50 Ohms, Vo = 1.4V Iib+ IibInput Bias Current Input Bias Current V+ = 5V, Vcm = 0V V+ = 5V, Vcm = 0V -0.5 -0.5 -0.5 -10 -10 0.5 0.5 0.5 10 10 mV mV mV nA nA 1 1 1 1 1 Graphics and Diagrams GRAPHICS# 08571HRC2 09294HR01 H08CRF DESCRIPTION METAL CAN (H), TO-99, 8LD, .200 DIA P.C. (B/I CKT) CERDIP (J), 8 LEAD (B/I CKT) METAL CAN (H), TO-99, 8LD, .200 DIA P.C. (P/P DWG) J08ARL CERDIP (J), 8 LEAD (P/P DWG) See attached graphics following this page. 6 MNLM158A-X REV 3A0 MICROCIRCUIT DATA SHEET Graphics and Diagrams GRAPHICS# P000273A P000274A (Continued) DESCRIPTION METAL CAN (H), 8 LEAD (PINOUT) CERDIP (J), 8 LEAD (PINOUT) See attached graphics following this page. 7 N N MNLM158A-X REV 3A0 MICROCIRCUIT DATA SHEET Revision History Rev 2AL ECN # Rel Date Originator Barbara Lopez Changes Changes: Corrected typo, AVS test limits moved to min column from max column. Changed CMRR condition to: V+ = 30V, Vin = 0V to 28.5V, Rs = 50 Ohms. Update MDS: MNLM158A-X Rev. 2AL to MNLM158A-X Rev. 3A0. Added "QMLV" devices to MDS. Add reference to "QMLV" device to SMD number. Added Burn-In, Pinout and MKT outline. Changed Drift statement. M0001409 10/15/98 3A0 M0002807 10/15/98 Barbara Lopez 8 |
Price & Availability of NSC05475
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |