View SCDS109_1000524.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SN74CBTR32245 32-BIT FET BUS SWITCH
SCDS109 - MAY 2000
D D D
Member of the Texas Instruments Widebus +TM Family 32-Bit Version of QS3245 25- Switch Connection Between Two Ports
D D D
TTL-Compatible Input Levels Flow-Through Architecture Optimizes PCB Layout Packaged in Plastic Fine-Pitch Ball Grid Array Package
description
The SN74CBTR32245 device provides 32 bits of high-speed TTL-compatible bus switching. The low on-state resistance of the switch allows connections to be made with minimal propagation delay. The device is organized as four 8-bit bus switches, two 16-bit bus switches, or one 32-bit bus switch. When output enable (OE) is low, the switch is on, and port A is connected to port B. When OE is high, the switch is open, and a high-impedance state exists between the two ports. The device has equivalent 25- series resistors to reduce signal-reflection noise. This eliminates the need for external terminating resistors. The SN74CBTR32245 is characterized for operation from -40C to 85C.
INPUT OE L H
FUNCTION A port = B port Disconnect
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus+ is a trademark of Texas Instruments.
PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice.
Copyright (c) 2000, Texas Instruments Incorporated
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
1
PRODUCT PREVIEW
FUNCTION TABLE (each 8-bit bus switch)
SN74CBTR32245 32-BIT FET BUS SWITCH
SCDS109 - MAY 2000
GKE PACKAGE (TOP VIEW) 1 A B C D E F G H J K L M 2 3 4 5 6
terminal assignments
1 A B C D E F G H J K L M N P R T 1B2 1B4 1B6 1B8 2B2 2B4 2B6 2B7 3B2 3B4 3B6 3B8 4B2 4B4 4B6 4B7 2 1B1 1B3 1B5 1B7 2B1 2B3 2B5 2B8 3B1 3B3 3B5 3B7 4B1 4B3 4B5 4B8 3 NC GND VCC GND GND VCC GND NC NC GND VCC GND GND VCC GND NC 4 1OE GND VCC GND GND VCC GND 2OE 3OE GND VCC GND GND VCC GND 4OE 5 1A1 1A3 1A5 1A7 2A1 2A3 2A5 2A8 3A1 3A3 3A5 3A7 4A1 4A3 4A5 4A8 6 1A2 1A4 1A6 1A8 2A2 2A4 2A6 2A7 3A2 3A4 3A6 3A8 4A2 4A4 4A6 4A7
PRODUCT PREVIEW
N P R T
NC - No internal connection
logic diagram (positive logic)
1A1 A5 A2 1B1 2A1 E5 E2 2B1
D6 1A8 A4 1OE
D1 1B8 2A8
H5
H2 2B8
H4 2OE
3A1
J5
J2
3B1
4A1
N5
N2
4B1
M6 3A8 J4 3OE
M1 3B8 4A8
T5
T2
4B8
T4 4OE
2
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
SN74CBTR32245 32-BIT FET BUS SWITCH
SCDS109 - MAY 2000
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Continuous channel current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Package thermal impedance, JA (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51.
recommended operating conditions (see Note 3)
MIN VCC VIH VIL TA Supply voltage High-level control input voltage Low-level control input voltage Operating free-air temperature -40 4 2 0.8 85 MAX 5.5 UNIT V V C V
NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to TI application report Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
3
PRODUCT PREVIEW
SN74CBTR32245 32-BIT FET BUS SWITCH
SCDS109 - MAY 2000
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER VIK II ICC ICC Ci Control inputs Control inputs VCC = 4.5 V, VCC = 5.5 V, VCC = 5.5 V, VCC = 5.5 V, VI = 3 V or 0 VO = 3 V or 0, VCC = 4 V, TYP at VCC = 4 V ron VCC = 4.5 V TEST CONDITIONS II = -18 mA VI = 5.5 V or GND IO = 0, One input at 3.4 V, OE = VCC VI = 2.4 V, VI = 0 II = 15 mA II = 64 mA II = 30 mA VI = VCC or GND Other inputs at VCC or GND MIN TYP MAX -1.2 5 50 3.5 UNIT V A A mA pF pF
Cio(OFF)
PRODUCT PREVIEW
VI = 2.4 V, II = 15 mA All typical values are at VCC = 5 V (unless otherwise noted), TA = 25C. This is the increase in supply current for each input that is at the specified TTL-voltage level rather than VCC or GND. Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by the lower of the voltages of the two (A or B) terminals.
switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1)
PARAMETER tpd ten FROM (INPUT) A or B OE TO (OUTPUT) B or A A or B VCC = 4 V MIN MAX VCC = 5 V 0.5 V MIN MAX ns ns UNIT
tdis A or B ns OE The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance).
4
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
SN74CBTR32245 32-BIT FET BUS SWITCH
SCDS109 - MAY 2000
PARAMETER MEASUREMENT INFORMATION
7V From Output Under Test CL = 50 pF (see Note A) 500 S1 Open GND 500 Output Control (low-level enabling) tPZL 3V Input 1.5 V 1.5 V 0V tPLH Output 1.5 V VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES tPHL VOH 1.5 V VOL Output Waveform 1 S1 at 7 V (see Note B) tPZH Output Waveform 2 S1 at Open (see Note B) 1.5 V 1.5 V TEST tpd tPLZ/tPZL tPHZ/tPZH S1 Open 7V Open
3V 1.5 V 1.5 V 0V tPLZ 3.5 V VOL + 0.3 V VOL tPHZ
LOAD CIRCUIT
0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd.
Figure 1. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
5
PRODUCT PREVIEW
VOH VOH - 0.3 V
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof.
Copyright (c) 2000, Texas Instruments Incorporated

▲Up To Search▲

Price & Availability of SCDS109

	To Download SCDS109 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .