View W180_1007211.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

W180
Peak Reducing EMI Solution
Features
* Cypress PREMISTM family offering * Generates an EMI optimized clocking signal at the output * Selectable output frequency range * Single -1.25% or -3.75% down spread output * Integrated loop filter components * Operates with a 3.3V or 5V supply * Low power CMOS design * Available in 8-pin SOIC (Small Outline Integrated Circuit) Table 1. Modulation Width Selection SS% 0 1 Output Fin Fout Fin - 1.25% Fin Fout Fin - 3.75%
Table 2. Frequency Range Selection W180 Option# FS2 0 0 1 1 FS1 0 1 0 1 -01 (MHz) 8 FIN 10 10 FIN 15 15 FIN 18 18 FIN 28 -02 (MHz) 8 FIN 10 10 FIN 15 N/A N/A -03 (MHz) N/A N/A 15 FIN 18 18 FIN 28
Key Specifications
Supply Voltages: .........................................VDD = 3.3V0.3V or VDD = 5V10% Frequency range: ................................ 8 MHz Fin 28 MHz Cycle to Cycle Jitter: ........................................ 300 ps (max) Selectable spread percentage: .................-1.25% or -3.75% Output duty cycle: ................................ 40/60% (worst case) Output rise and fall time: ....................................... 5 ns (max)
Simplified Block Diagram
3.3V or 5.0V
Pin Configurations
SOIC CLKIN or X1 NC or X2 GND SS% 1 2 3 4 8 7 6 5 FS2 FS1 VDD CLKOUT W180-01
X1 XTAL Input
X2
W180
Spread Spectrum Output (EMI suppressed)
W180-02/03
CLKIN or X1 NC or X2 GND SS%
1 2 3 4
8 7 6 5
SSON# FS1 VDD CLKOUT
3.3V or 5.0V
Oscillator or Reference Input
W180
Spread Spectrum Output (EMI suppressed)
PREMIS is a trademark of Cypress Semiconductor Corporation.
Cypress Semiconductor Corporation
*
3901 North First Street
*
San Jose
*
CA 95134 * 408-943-2600 September 28, 1999, rev. **
W180
Pin Definitions
Pin Name CLKOUT CLKIN or X1 Pin No. 5 1 Pin Type O I Pin Description Output Modulated Frequency: Frequency modulated copy of the unmodulated input clock (SSON# asserted). Crystal Connection or External Reference Frequency Input: This pin has dual functions. It may either be connected to an external crystal, or to an external reference clock. Crystal Connection: Input connection for an external crystal. If using an external reference, this pin must be left unconnected. Spread Spectrum Control (Active LOW): Asserting this signal (active LOW) turns the internal modulation waveform on. This pin has an internal pull-down resistor. Frequency Selection Bit(s) 1 and 2: These pins select the frequency range of operation. Refer to Table 2. These pins have internal pull-up resistors. Modulation Width Selection: When Spread Spectrum feature is turned on, this pin is used to select the amount of variation and peak EMI reduction that is desired on the output signal. Internal pull-up resistor. Power Connection: Connected to 3.3V or 5V power supply. Ground Connection: This should be connected to the common ground plane.
NC or X2 SSON#
2 8 (-02, -03)
I I
FS1:2 SS%
7, 8 (-01 only) 4
I I
VDD GND
6 3
P G
2
W180
Overview
The W180 products are one series of devices in the Cypress PREMIS family. The PREMIS family incorporates the latest advances in PLL spread spectrum frequency synthesizer techniques. By frequency modulating the output with a low-frequency carrier, peak EMI is greatly reduced. Use of this technology allows systems to pass increasingly difficult EMI testing without resorting to costly shielding or redesign. In a system, not only is EMI reduced in the various clock lines, but also in all signals which are synchronized to the clock. Therefore, the benefits of using this technology increase with the number of address and data lines in the system. The Simplified Block Diagram on page 1 shows a simple implementation. input. The output frequency is then equal to the ratio of P/Q times the reference frequency. (Note: For the W180 the output frequency is equal to the input frequency.) The unique feature of the Spread Spectrum Frequency Timing Generator is that a modulating waveform is superimposed at the input to the VCO. This causes the VCO output to be slowly swept across a predetermined frequency band. Because the modulating frequency is typically 1000 times slower than the fundamental clock, the spread spectrum process has little impact on system performance. Frequency Selection With SSFTG In Spread Spectrum Frequency Timing Generation, EMI reduction depends on the shape, modulation percentage, and frequency of the modulating waveform. While the shape and frequency of the modulating waveform are fixed for a given frequency, the modulation percentage may be varied. Using frequency select bits (FS2:1 pins), the frequency range can be set (see Table 2). Spreading percentage is set with pin SS% as shown in Table 1. A larger spreading percentage improves EMI reduction. However, large spread percentages may either exceed system maximum frequency ratings or lower the average frequency to a point where performance is affected. For these reasons, spreading percentages options are provided.
Functional Description
The W180 uses a phase-locked loop (PLL) to frequency modulate an input clock. The result is an output clock whose frequency is slowly swept over a narrow band near the input signal. The basic circuit topology is shown in Figure 1. The input reference signal is divided by Q and fed to the phase detector. A signal from the VCO is divided by P and fed back to the phase detector also. The PLL will force the frequency of the VCO output signal to change until the divided output signal and the divided reference signal match at the phase detector
VDD
Clock Input Freq. Divider Q Phase Detector Charge Pump
Reference Input
VCO
Post Dividers
CLKOUT (EMI suppressed)
Modulating Waveform Feedback Divider P
PLL
GND
Figure 1. Functional Block Diagram
3
W180
Spread Spectrum Frequency Timing Generation
The benefits of using Spread Spectrum Frequency Timing Generation are depicted in Figure 2. An EMI emission profile of a clock harmonic is shown. Contrast the typical clock EMI with the Cypress Spread Spectrum Frequency Timing Generation EMI. Notice the spike in the typical clock. This spike can make systems fail quasi-peak EMI testing. The FCC and other regulatory agencies test for peak emissions. With spread spectrum enabled, the peak energy is much lower (at least 8 dB) because the energy is spread out across a wider bandwidth. Modulating Waveform The shape of the modulating waveform is critical to EMI reduction. The modulation scheme used to accomplish the maximum reduction in EMI is shown in Figure 3. The period of the modulation is shown as a percentage of the period length along the X axis. The amount that the frequency is varied is shown along the Y axis, also shown as a percentage of the total frequency spread. Cypress frequency selection tables express the modulation percentage in two ways. The first method displays the spreading frequency band as a percent of the programmed average output frequency, symmetric about the programmed average frequency. This method is always shown using the expression fCenter XMOD% in the frequency spread selection table. The second approach is to specify the maximum operating frequency and the spreading band as a percentage of this frequency. The output signal is swept from the lower edge of the band to the maximum frequency. The expression for this approach is fMAX - XMOD%. Whenever this expression is used, Cypress has taken care to ensure that fMAX will never be exceeded. This is important in applications where the clock drives components with tight maximum clock speed specifications.
Spread Spectrum Enabled NonSpread Spectrum
EMI Reduction
Figure 2. Typical Clock and SSFTG Comparison
SSON# Pin An internal pull-down resistor defaults the chip into spread spectrum mode. When the SSON# pin is asserted (active LOW) the spreading feature is enabled. Spreading feature is disabled when SSON# is set HIGH (VDD).
100% 80% 60% 40% 20% 0% -20% -40% -60% -80% -100%
Frequency Shift
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
10%
20%
30%
40%
50%
60%
70%
80%
90%
Time
Figure 3. Modulation Waveform Profile
4
100%
W180
Absolute Maximum Ratings
Stresses greater than those listed in this table may cause permanent damage to the device. These represent a stress rating only. Operation of the device at these or any other conditions
.
above those specified in the operating sections of this specification is not implied. Maximum conditions for extended periods may affect reliability Rating -0.5 to +7.0 -65 to +150 0 to +70 -55 to +125 0.5 Unit V C C C W
Parameter VDD, VIN TSTG TA TB PD
Description Voltage on any pin with respect to GND Storage Temperature Operating Temperature Ambient Temperature under Bias Power Dissipation
DC Electrical Characteristics: 0C < TA < 70C, VDD = 3.3V 0.3V
Parameter IDD tON VIL VIH VOL VOH IIL IIH IOL IOH CI RP ZOUT Description Supply Current Power Up Time Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage Input Low Current Input High Current Output Low Current Output High Current Input Capacitance Input Pull-Up Resistor Clock Output Impedance 500 25 Note 1 Note 1 @ 0.4V, VDD = 3.3V @ 2.4V, VDD = 3.3V 15 15 7 2.4 -50 50 2.4 0.4 First locked clock cycle after Power Good Test Condition Min Typ 18 Max 32 5 0.8 Unit mA ms V V V V A A mA mA pF k
Note: 1. Inputs FS2:1& SS% have a pull-up resistor; Input SSON# has a pull-down resistor.
5
W180
DC Electrical Characteristics: 0C < TA < 70C, VDD = 5V 10%
Parameter IDD tON VIL VIH VOL VOH IIL IIH IOL IOH CI RP ZOUT Description Supply Current Power Up Time Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage Input Low Current Input High Current Output Low Current Output High Current Input Capacitance Input Pull-Up Resistor Clock Output Impedance 500 25 Note 2 Note 2 @ 0.4V, VDD = 5V @ 2.4V, VDD = 5V 24 24 7 2.4 -50 50 0.7VDD 0.4 First locked clock cycle after Power Good Test Condition Min Typ 30 Max 50 5 0.15VDD Unit mA ms V V V V A A mA mA pF k
AC Electrical Characteristics: TA = 0C to +70C, VDD = 3.3V 0.3V or 5V10%
Symbol fIN fOUT tR tF tOD tID tJCYC Parameter Input Frequency (-01) Output Frequency (-01) Output Rise Time Output Fall Time Output Duty Cycle Input Duty Cycle Jitter, Cycle-to-Cycle Harmonic Reduction fout = 20 MHz, third harmonic measured, reference board, 15-pF load 8 Test Condition Input Clock, Note 3 Spread Off, Note 3 15-pF load 0.8V-2.4V 15-pF load 2.4 -0.8V 15-pF load 40 40 250 Min 8 8 2 2 Typ Max 28 28 5 5 60 60 300 Unit MHz MHz ns ns % % ps dB
Notes: 2. Inputs FS1:2 have a pull-up resistor; Input SSON# has a pull-down resistor. 3. Frequency range listed for -01 version. See Table 2 for frequency range of -02 and -03 versions.
6
W180
Application Information
Recommended Circuit Configuration For optimum performance in system applications the power supply decoupling scheme shown in Figure 4 should be used. VDD decoupling is important to both reduce phase jitter and EMI radiation. The 0.1-F decoupling capacitor should be placed as close to the VDD pin as possible, otherwise the inXtal Connection or Reference Input Xtal Connection or NC GND
creased trace inductance will negate its decoupling capability. The 10-F decoupling capacitor shown should be a tantalum type. For further EMI protection, the VDD connection can be made via a ferrite bead, as shown. Recommended Board Layout Figure 5 shows a recommended 2-layer board layout.
1 W180 2 3 4
8 7 6 5
R1 Clock Output C1 0.1 F
3.3V or 5V System Supply
FB
C2 10 F Tantalum
Figure 4. Recommended Circuit Configuration
C1 = C2 =
High frequency supply decoupling capacitor (0.1-F recommended). Common supply low frequency decoupling capacitor (10-F tantalum recommended). Match value to line impedance Ferrite Bead
Via To GND Plane
R1 = FB =
G
Xtal Connection or Reference Input NC
=
C1 G G
Clock Output R1
G
Power Supply Input (3.3V or 5V) FB
C2
Figure 5. Recommended Board Layout (2-Layer Board)
Ordering Information
Ordering Code W180 Document #: 38-00796 Freq. Mask Code 01, 02, 03 Package Name G Package Type 8-pin Plastic SOIC (150-mil)
7
W180
Package Diagram
8-Pin Small Outline Integrated Circuit (SOIC, 150 mils)
(c) Cypress Semiconductor Corporation, 1999. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.

▲Up To Search▲

Price & Availability of W180

	To Download W180 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .