View PM400HSA12000_1039507.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MITSUBISHI INTELLIGENT POWER MODULES
PM400HSA120
FLAT-BASE TYPE INSULATED PACKAGE
A C N E F N
R-DIA.(4 Typ.)
S
U-DIA.(2 Typ.)
T-(4 Typ.)
BD
J
12345
5. FO 4. VC 3. CI 2. SR 1. V1
E 0.64 MM SQ. PIN (5 Typ.)
C P-THD.(2 Typ.) K L
M
Q
G
LABEL
H
V1 1
C Rref Vcc
Description: Mitsubishi Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: Complete Output Power Circuit Gate Drive Circuit Protection Logic - Short Circuit - Over Current - Over Temperature - Under Voltage Applications: Inverters UPS Motion/Servo Control Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM400HSA120 is a 1200V, 400 Ampere Intelligent Power Module.
Type PM Current Rating Amperes 400 VCES Volts (x 10) 120
FO 5
Rfo
TEMP FO OUT1 AMP Rg Th
SR 2
SR
OUT2 SENS
CI 3 Ci VC 4
IN SINK GND
E
Outline Drawing and Circuit Diagram
Dimensions A B C D E F G H J K
Inches 3.86 3.46 3.150.01 2.760.01 2.56 1.57
Millimeters 98.0 88.0 80.00.25 70.00.25 65.0 40.0
Dimensions L M N P Q R S T U
Inches 0.63 0.59 0.35 Metric M8 0.28 0.26 Dia. 0.10 0.100 0.08 Dia.
Millimeters 16.0 15.0 9.0 M8 7.0 Dia. 6.5 2.5 2.54 2.0 Dia.
1.34 +0.04/-0.02 34.0 +1.0/-0.5 1.16 0.79 0.71 29.5 20.0 18.0
Sep.2000
MITSUBISHI INTELLIGENT POWER MODULES
PM400HSA120
FLAT-BASE TYPE INSULATED PACKAGE Absolute Maximum Ratings, Tj = 25C unless otherwise specified
Symbol Power Device Junction Temperature Storage Temperature Case Operating Temperature Mounting Torque, M6 Mounting Screws Mounting Torque, M8 Main Terminal Screws Module Weight (Typical) Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V, Inverter Part) Isolation Voltage (Main Terminal to Baseplate, AC 1 min.) Tj Tstg TC -- -- -- VCC(prot.) Viso Ratings -20 to 150 -40 to 125 -20 to 100 3.92~5.88 8.83~10.8 630 800 2500 Units C C C N*m N*m Grams Volts Vrms
Control Sector
Supply Voltage (Applied between V1-VC) Input Voltage (Applied between C1-VC ) Fault Output Supply Voltage (Applied between Fo-Vc ) Fault Output Current (Fault Current of FO Terminal) VD VCIN VFO IFO 20 10 20 20 Volts Volts Volts mA
IGBT Inverter Sector
Collector-Emitter Voltage (VD = 15V, VCIN = 5V) Collector Current, (TC = 25C) Peak Collector Current, (TC = 25C) Collector Dissipation VCES IC ICP PC 1200 400 800 2315 Volts Amperes Amperes Watts
Electrical and Mechanical Characteristics, Tj = 25C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Control Sector
Over Current Trip Level Inverter Part Short Circuit Trip Level Inverter Part Over Current Delay Time Over Temperature Protection OC SC t off(OC) OT OTr Supply Circuit Under Voltage Protection UV UVr Supply Voltage Circuit Current Input ON Threshold Voltage Input OFF Threshold Voltage PWM Input Frequency Fault Output Current VD ID Vth(on) Vth(off) f PWM IFO(H) IFO(L) Minimum Fault Output Pulse Width SR Terminal Output Voltage tFO VSR -20C Tj 125C, VD = 15V -20C Tj 125C, VD = 15V VD = 15V Trip Level Reset Level Trip Level Reset Level Applied between V 1-VC VD = 15V, VCIN = 5V, V1-VC Applied between C1-VC Applied between C1-VC 3- Sinusoidal VD = 15V, VFO = 15V VD = 15V, VFO = 15V VD = 15V -20C Tj 125C, Rin = 6.8 k 480 650 -- 100 85 11.5 -- 13.5 -- 1.2 1.7 -- -- -- 1.0 4.5 650 930 5 110 95 12.0 12.5 15 23 1.5 2.0 15 -- 10 1.8 5.1 -- -- -- 120 105 12.5 -- 16.5 30 1.8 2.3 20 0.01 15 -- 5.6 Amperes Amperes s C C Volts Volts Volts mA Volts Volts kHz mA mA ms Volts
Sep.2000
MITSUBISHI INTELLIGENT POWER MODULES
PM400HSA120
FLAT-BASE TYPE INSULATED PACKAGE Electrical and Mechanical Characteristics, Tj = 25C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
IGBT Inverter Sector
Collector Cutoff Current ICES VEC VCE(sat) VCE = VCES, Tj = 25C VCE = VCES, Tj = 125C Emitter-Collector Voltage Collector-Emitter Saturation Voltage -IC = 400A, VD = 15V, VCIN = 5V VD = 15V, VCIN = 0V, IC = 400A, Tj = 25C, Pulsed VD = 15V, VCIN = 0V, IC = 400A, Tj = 125C, Pulsed Inductive Load Switching Times ton trr tC(on) toff tC(off) VD = 15V, VCIN = 0 5V VCC = 600V, IC = 400A Tj = 125C 0.5 -- -- -- -- 1.4 0.2 0.4 2.5 0.6 2.5 0.4 1.0 3.5 1.1 s s s s s -- 2.1 2.9 Volts -- -- -- -- -- -- 2.5 2.3 1.0 10 3.5 3.2 mA mA Volts Volts
Thermal Characteristics
Characteristic Junction to Case Thermal Resistance Symbol Rth(j-c)Q Rth(j-c)F Contact Thermal Resistance R th(c-f) Condition Each IGBT Each FWDi Case to Fin Per Module, Thermal Grease Applied Min. -- -- -- Typ. -- -- -- Max. 0.054 0.10 0.038 Units C/Watt C/Watt C/Watt
Recommended Conditions for Use
Characteristic Supply Voltage Symbol VCC VD Input ON Voltage Input OFF Voltage PWM Input Frequency Minimum Dead Time VCIN(on) VCIN(off) f PWM tdead Condition Applied across C1-E2 Terminals Applied between V1-VC Applied between C1-VC Applied between C1-VC Using Application Circuit Input Signal Value 0 ~ 800 15 1.5 0 ~ 0.8 4.0 ~ VSR 5 ~ 20 3.5 Units Volts Volts Volts Volts kHz s
Sep.2000
MITSUBISHI INTELLIGENT POWER MODULES
PM400HSA120
FLAT-BASE TYPE INSULATED PACKAGE
SATURATION VOLTAGE CHARACTERISTICS (TYPICAL)
COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL)
OUTPUT CHARACTERISTICS (TYPICAL)
5
COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat), (VOLTS) SATURATION VOLTAGE VCE(sat), (VOLTS)
6
COLLECTOR CURRENT, IC, (AMPERES)
4
VD = 15V VCIN = 0V Tj = 25oC Tj = 125oC
IC = 400V VCIN = 0V Tj = 25oC Tj = 125oC
600
Tj = 25oC VCIN = 0V VD = 17V
13 15
4
400
3
2
2
200
1
0 0 200 400 600
COLLECTOR CURRENT, IC, (AMPERES)
0 10 12 14 16 18 20
SUPPLY VOLTAGE, VD, (VOLTS)
0 0 1 2 3 4 5
COLLECTOR-EMITTER VOLTAGE, VCE(sat), (VOLTS)
SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL)
REVERSE RECOVERY CURRENT VS. COLLECTOR CURRENT (TYPICAL)
DIODE FORWARD CHARACTERISTICS
101
VCC = 600V VD = 15V
Inductive Load
SWITCHING TIMES, ton, toff, (s)
101
VCC = 600V VD = 15V
REVERSE RECOVERY TIME, trr, (s)
103
COLLECTOR REVERSE CURRENT, -IC, (AMPERES) REVERSE RECOVERY CURRENT, Irr, (AMPERES)
103
VD = 15V Tj = 25oC Tj = 125oC
Tj = 125oC
Inductive Load
ton toff
Tj = 125oC
Irr
100
100
102
102
tc(off) tc(on)
trr
10-1 101
102
COLLECTOR CURRENT, IC, (AMPERES)
103
10-1 101
102
TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (Each FWDi)
101 103
101 0 1 2 3
EMITTER-COLLECTOR VOLTAGE, VEC, (VOLTS)
COLLECTOR REVERSE CURRENT, -IC, (AMPERES)
TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (Each IGBT)
TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE)
101
TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE)
101
100
100
10-1
10-1
10-2
SINGLE PULSE STANDARD VALUE = Rth(j-c)Q = 0.054oC/W
10-2
SINGLE PULSE STANDARD VALUE = Rth(j-c)F = 0.1oC/W
10-3 10-3
10-2
10-1
TIME, (s)
100
101
10-3 10-3
10-2
10-1
TIME, (s)
100
101
Sep.2000

▲Up To Search▲

Price & Availability of PM400HSA12000

	To Download PM400HSA12000 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .