|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Previous Datasheet Index Next Data Sheet Bulletin I25196/A ST1200C..K SERIES PHASE CONTROL THYRISTORS Hockey Puk Version 1650A Features Center amplifying gate Metal case with ceramic insulator International standard case A-24 (K-PUK) High profile hockey-puk Typical Applications DC motor controls Controlled DC power supplies AC controllers case style A-24 (K-PUK) Major Ratings and Characteristics Parameters IT(AV) @ Ths IT(RMS) @ Ths ITSM @ 50Hz @ 60Hz I 2t @ 50Hz @ 60Hz V DRM /V RRM tq TJ typical ST1200C..K 1650 55 3080 25 30500 32000 4651 4250 1200 to 2000 200 - 40 to 125 Units A C A C A A KA2s KA2s V s C To Order Previous Datasheet ST1200C..K Series ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage Type number Code 12 14 ST1200C..K 16 18 20 Index Next Data Sheet V DRM /V RRM , max. repetitive peak and off-state voltage V 1200 1400 1600 1800 2000 VRSM , maximum nonrepetitive peak voltage V 1300 1500 1700 1900 2100 I DRM/I RRM max. @ TJ = TJ max mA 100 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature I T(RMS) Max. RMS on-state current I TSM Max. peak, one-cycle non-repetitive surge current ST1200C..K 1650 (700) 55 (85) 3080 30500 32000 25700 26900 Units Conditions A C 180 conduction, half sine wave double side (single side) cooled DC @ 25C heatsink temperature double side cooled t = 10ms A t = 8.3ms t = 10ms t = 8.3ms t = 10ms KA2s t = 8.3ms t = 10ms t = 8.3ms KA s 2 No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial T J = TJ max. It 2 Maximum I t for fusing 2 4651 4250 3300 3000 I t 2 Maximum I t for fusing 2 46510 0.91 t = 0.1 to 10ms, no voltage reapplied (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. V T(TO)1 Low level value of threshold voltage V T(TO)2 High level value of threshold voltage r t1 r t2 V TM IH IL Low level value of on-state slope resistance High level value of on-state slope resistance Max. on-state voltage Maximum holding current Typical latching current V 1.01 (I > x IT(AV)),TJ = TJ max. (16.7% x x IT(AV) < I < x IT(AV) ), TJ = TJ max. m 0.19 1.73 600 mA 1000 T J = 25C, anode supply 12V resistive load V (I > x IT(AV) ),TJ = TJ max. Ipk= 4000A, TJ = TJ max, t p = 10ms sine pulse 0.21 To Order Previous Datasheet Index Next Data Sheet ST1200C..K Series Switching Parameter di/dt Max. non-repetitive rate of rise of turned-on current t d ST1200C..K 1000 1.9 Units Conditions A/s Gate drive 20V, 20, tr 1s TJ = TJ max, anode voltage 80% VDRM Gate current 1A, di g /dt = 1A/s s Vd = 0.67% VDRM, TJ = 25C ITM = 550A, TJ = TJ max, di/dt = 40A/s, VR = 50V dv/dt = 20V/s, Gate 0V 100, tp = 500s Typical delay time Typical turn-off time tq 200 Blocking Parameter dv/dt IRRM IDRM Maximum critical rate of rise of Max. peak reverse and off-state leakage current ST1200C..K 500 off-state voltage 100 Units Conditions V/s mA TJ = TJ max. linear to 80% rated VDRM TJ = TJ max, rated V DRM /VRRM applied Triggering Parameter PGM Maximum peak gate power ST1200C..K 16 3 3.0 20 Units Conditions W A TJ = TJ max, t p 5ms TJ = TJ max, f = 50Hz, d% = 50 TJ = TJ max, t p 5ms PG(AV) Maximum average gate power IGM +VGM -VGM Max. peak positive gate current Maximum peak positive gate voltage Maximum peak negative gate voltage TYP. 200 IGT DC gate current required to trigger 100 50 1.4 VGT DC gate voltage required to trigger IGD VGD DC gate current not to trigger DC gate voltage not to trigger 1.1 0.9 V 5.0 MAX. 200 3.0 10 0.25 mA V V mA TJ = TJ max, tp 5ms TJ = - 40C TJ = 25C TJ = 125C TJ = - 40C TJ = 25C TJ = 125C Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied TJ = TJ max To Order Previous Datasheet ST1200C..K Series Index Next Data Sheet Thermal and Mechanical Specification Parameter TJ Tstg Max. operating temperature range Max. storage temperature range ST1200C..K -40 to 125 -40 to 150 0.042 0.021 0.006 0.003 24500 (2500) Units C Conditions RthJ-hs Max. thermal resistance, junction to heatsink RthC-hs Max. thermal resistance, case to heatsink F Mounting force, 10% DC operation single side cooled K/W DC operation double side cooled DC operation single side cooled DC operation double side cooled K/W N (Kg) g wt Approximate weight Case style 425 A-24 (K-PUK) See Outline Table RthJ-hs Conduction (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Sinusoidal conduction Conduction angle 180 120 90 60 30 Single Side Double Side 0.003 0.004 0.005 0.007 0.012 0.003 0.004 0.005 0.007 0.012 Rectangular conduction Single Side Double Side 0.002 0.004 0.005 0.007 0.012 0.002 0.004 0.005 0.007 0.012 K/W Units Conditions TJ = TJ max. Ordering Information Table Device Code ST 120 1 2 0 3 C 4 20 5 K 6 1 7 8 1 2 3 4 5 6 7 - Thyristor Essential part number 0 = Converter grade C = Ceramic Puk Voltage code: Code x 100 = VRRM (See Voltage Rating Table) K = Puk Case A-24 (K-PUK) 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 8 - Critical dv/dt: None = 500V/sec (Standard selection) L = 1000V/sec (Special selection) To Order Previous Datasheet Index Next Data Sheet ST1200C..K Series Outline Table 1 (0.04) MIN. TWO PLACES 27.5 (1.08) MAX. 47.5 (1.87) DIA. MAX. TWO PLACES PIN RECEPTACLE AMP. 60598-1 Case Style A-24 (K-PUK) 67 (2.6) DIA. MAX. All dimensions in millimeters (inches) 20 5 74.5 (2.9) DIA. MAX. 4.75 (0.2) NOM. 44 (1.73) 2 HOLES DIA. 3.5 (0.14) x 2.1 (0.1) DEEP CREPAGE DESTANCE 28.88 (1.137) MIN. STRIKE DISTANCE 17.99 (0.708) MIN. Maximum Allowable Heatsink T emperature (C) 130 120 110 100 90 80 70 60 50 40 0 200 400 600 800 1000 1200 Average On-state Current (A) Fig. 1 - Current Ratings Characteristics 30 60 90 120 180 Conduc tion Angle Maximum Allowable Heatsink T emperature (C) 130 120 110 100 90 80 70 60 50 40 30 20 0 400 30 S 1200C..K Series T (S ingle S ide Cooled ) RthJ-hs(DC) = 0.042 K/ W S 1200C..K S T eries (S ingle S Cooled) ide RthJ-hs(DC) = 0.042 K/ W Conduction Period 60 90 120 180 800 1200 DC 1600 2000 Average On-state Current (A) To Order Fig. 2 - Current Ratings Characteristics Previous Datasheet ST1200C..K Series Maximum Allowable Heats T ink emperature (C) Index Next Data Sheet Maximum Allowa ble Heatsink T emperature (C) 130 120 110 100 90 80 70 60 50 40 30 0 400 800 1200 1600 2000 Average On-s tate Current (A) Fig. 3 - Current Ratings Characteristics 30 60 90 120 180 Conduc tion Angle 130 120 110 100 90 80 70 60 50 40 30 20 0 30 S 1200C..K S T eries (Double S Cooled) ide RthJ-hs(DC) = 0.021 K/W S 1200C..K S T eries (Double S Cooled) ide RthJ-hs(DC) = 0.021 K/ W Conduction Period 90 60 120 180 DC 500 1000 1500 2000 2500 3000 3500 Average On-state Current (A) Fig. 4 - Current Ratings Characteristics Maximum Average On-state Power Loss(W) Maximum Average On-state Power Loss (W) 4000 3500 3000 2500 2000 1500 1000 500 0 0 180 120 90 60 30 RMS Limit 5000 DC 180 120 90 60 30 RMS Limit 2000 4000 3000 Conduction Period Conduction Angle S 1200C..K S T eries T = 125C J 400 800 1200 1600 2000 1000 S 1200C..K S T eries T = 125C J 0 0 500 1000 1500 2000 2500 3000 3500 Average On-s tate Current (A) Fig. 6- On-state Power Loss Characteristics Average On-state Current (A) Fig. 5- On-state Power Loss Characteristics Peak Half S Wave On-state Current (A) ine 28000 26000 24000 22000 20000 18000 16000 14000 S 1200C..K S T eries 12000 1 10 100 Number Of Equal Amplitude Half Cycle Current Pulses (N) Peak Half S Wave On-state Current (A) ine At Any Rated Load Condition And With R ated VRR Applied Following S urge. M Initial T = 125C J @60 Hz 0.0083 s @50 Hz 0.0100 s 32000 30000 Maximum Non R epetitive S urge Current Vers Pulse T us rain Duration. Control Of Conduction May Not Be Maintained. 28000 Initial T = 125C J No Voltage Reapplied 26000 R ated VR Reapplied RM 24000 22000 20000 18000 16000 14000 12000 0.01 S 1200C..K S T eries 0.1 Pulse T rain Duration (s) 1 Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled To Order Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled Previous Datasheet Index Next Data Sheet ST1200C..K Series 10000 Instantaneous On-state Current (A) 1000 T = 25C J T = 125C J S 1200C..K Series T 100 0.5 1 1.5 2 2.5 3 Ins tantaneous On-state Voltage (V) Fig. 9 - On-state Voltage Drop Characteristics T rans ient T hermal Impedance Z thJ-hs (K/ W) 0.1 S teady S tate Value R thJ-hs = 0.042 K/ W (S ingle S Cooled) ide R thJ-hs = 0.021 K/ W (Double S Cooled) ide 0.01 (DC Operation) S 1200C..K S T eries 0.001 0.001 0.01 0.1 1 10 100 S quare Wave Pulse Duration (s ) Fig. 10 - Thermal Impedance ZthJ-hs Characteristics 100 Instantaneous Gate Voltage (V) Rectangular gate pulse a) Recommended load line for rated di/dt : 20V, 10ohms; tr<=1 s b) Recommended load line for <=30%rated di/dt : 10V, 10ohms 10 tr<=1 s (b) (1) PGM = 16W, tp = 4ms (2) PGM = 30W, tp = 2ms (3) PGM = 60W, tp = 1ms (a) T j=-40 C T j=25 C 1 VGD IGD 0.1 0.001 0.01 Device: S 1200C..K S T eries 0.1 1 Instantaneous Gate Current (A) Fig. 11 - Gate Characteristics T j=125 C (1) (2) (3) F requency Limited by PG(AV) 10 100 To Order |
Price & Availability of ST1200C |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |