![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
EEPROM Austin Semiconductor, Inc. AS8ER128K32 End O f Life PLEASE NOTE: An EOL notice was issued on this product in 2001. However, ASI has a large amount of die inventory available. For assistance, please contact your local sales representative. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 1 EEPROM Austin Semiconductor, Inc. 128K x 32 EEPROM Radiation Tolerant EEPROM Memory Array AVAILABLE AS MILITARY SPECIFICATIONS * * * * * MIL-STD-883 I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 GND I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 AS8ER128K32 PIN ASSIGNMENT (Top View) 68 Lead CQFP 9 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 10 60 11 59 12 58 13 57 14 56 15 55 16 54 17 53 18 52 19 51 20 50 21 49 22 48 23 47 24 46 25 45 26 44 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Vcc A11 A12 A13 *A15 *A14 A16 CS1\ OE\ CS2\ NC WE2\ WE3\ WE4\ NC NC RDY RES\ A0 A1 A2 A3 A4 A5 CS3\ GND CS4\ WE1\ A6 A7 A8 A9 A10 Vcc SMD 5962-94585 Access time of 150ns Operation with single 5V + 10% supply Power Dissipation: Active: 1.43 W (MAX), Max Speed Operation Standby: 7.7 mW (MAX), Battery Back-up Mode On-Chip Latches: Address, Data, CE\, OE\, WE\ Automatic Byte Write: 10 ms (MAX) Automatic Page Write (128 bytes): 10 ms (MAX) Data protection circuit on power on/off Low power CMOS 104 Erase/Write cycles (in Page Mode) Software data protection TTL Compatible Inputs and Outputs Data Retention: 10 years Ready/Busy\ and Data Polling Signals Write protection by RES\ pin Radiation Tolerant: Proven total dose 40K to 100K RADS* Operating Temperature Ranges: Military: -55oC to +125oC Industrial: -40oC to +85oC FEATURES I/O16 I/O17 I/O18 I/O19 I/O20 I/O21 I/O22 I/O23 GND I/O24 I/O25 I/O26 I/O27 I/O28 I/O29 I/O30 I/O31 * * * * * * * * * * * * * OPTIONS * End O f Life PIN NAME A0 to A16 I/O0 to I/O31 OE\ CE\ WE\ VCC FUNCTION Address Input Data Input/Output Output Enable Chip Enable Write Enable Power Supply *Pin #'s 31 and 32, A15 and A14 respectively, are reversed from the AS8E128K32. Correct use of these address lines is required for operation of the SDP mode to work properly. MARKINGS -150 -200 -250 Q QB Ground VSS RDY/BUSY\ Ready Busy RES\ Reset * Timing 150 ns 200 ns 250 ns Package Ceramic Quad Flat pack Ceramic Quad Flat pack No. 703 GENERAL DESCRIPTION The Austin Semiconductor, Inc. AS8ER128K32 is a 4 Megabit Radiation Tolerant EEPROM Module organized as 128K x 32 bit. User configurable to 256K x16 or 512Kx 8. The module achieves high speed access, low power consumption and high reliability by employing advanced CMOS memory technology. The military grade product is manufactured in compliance to MIL-STD 883, making the AS8ER128K32 ideally suited for military or space applications. The module is offered as a 68 lead 0.990 inch square ceramic quad flat pack. It has a max. height of 0.200 inch. This package design is targeted for those applications which require low profile SMT Packaging. * contact factory for test reports. ASI does not guarantee or warrant these performance levels, but references these third party reports. AS8ER128K32 Rev. 4.5 2/03 FUNCTIONAL BLOCK DIAGRAM For more products and information please visit our web site at www.austinsemiconductor.com Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 2 EEPROM Austin Semiconductor, Inc. AS8ER128K32 TRUTH TABLE MODE Read Standby Write Deselect Wirte Inhibit Data\ Polling CE\ VIL VIH VIL VIL X X OE\ VIL X 3 WE\ VIH X VIL VIH VIH X VIH X RES\ VH X VH VH X X 2 RDY/BUSY\ High-Z High-Z 1 I/O Dout High-Z Din High-Z ----- VIH VIH X VIL X High-Z to VOL High-Z ----- Program Reset NOTES: 1. RDY/Busy\ output has only active LOW VOL and high impedance state. It can not go to HIGH (VOH) state. 2. VCC -0.5 < VH < VCC +1.0 3. X : DON'T CARE End O f Life VIL X VIL VH VOL Dout (I/O7) High-Z VIL High-Z AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 3 EEPROM Austin Semiconductor, Inc. ABSOLUTE MAXIMUM RATINGS* Voltage on Vcc Supply Relative to Vss Vcc ....................................................................-0.6V to +7.0V Operating Temperature Range(1) ..................-55C to +125C Storage Temperature Range .........................-65C to +150C Voltage on any Pin Relative to Vss..............-0.5V to +7.0V (2) Max Junction Temperature**.......................................+150C Thermal Resistance junction to case (JC): Package Type Q...........................................11.3 C/W Package Type P & PN..................................2.8 C/W NOTES: 1) Including electrical characteristics and data retention. 2) VIN MIN = -3.0V for pulse width < 20ns. AS8ER128K32 *Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. **Junction temperature depends upon package type, cycle time, loading, ambient temperature and airflow, and humidity (plastics). ELECTRICAL CHARACTERISTICS AND RECOMMENDED DC OPERATING CONDITIONS (-55oC 2 INPUT LEAKAGE CURRENT OUTPUT LEAKAGE CURRENT Output High Voltage Output Low Voltage Supply Voltage End O f Life OV < VIN < VCC Outputs(s) Disabled, OV < VOUT < VCC IOH = -0.4mA IOL = 2.1mA ILO VOH VOL VCC -0.4 5.5 UNITS V V V V V V NOTE: 1) VIL (MIN): -1.0V for pulse width < 20ns. 2) ILI on RES\ : 500A (MAX) PARAMETER CONDITIONS Iout = 0mA, VCC = 5.5V Cycle = 1S, Duty = 100% SYM MAX -15 80 UNITS Power Supply Current: Operating Icc3 Iout = 0mA, VCC = 5.5V Cycle = MIN, Duty = 100% CE\ = VCC, VCC = 5.5V CE\ = VIH, VCC = 5.5V ICC1 ICC2 260 mA 1.4 12 mA mA Power Supply Current: Standby AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 4 EEPROM Austin Semiconductor, Inc. CAPACITANCE TABLE1 (VIN = 0V, f = 1 MHz, TA = 25oC) SYMBOL CADD COE CWE, CCE CIO PARAMETER A0 - A16 Capacitance OE\, RES\, RDY Capacitance WE\ and CE\ Capacitance I/O 0- I/O 31 Capacitance MAX 40 40 12 20 UNITS pF pF pF pF AS8ER128K32 NOTE: 1. This parameter is guaranteed but not tested. AC TEST CHARACTERISTICS TEST SPECIFICATIONS Input pulse levels...........................................VSS to 3V Input rise and fall times...........................................5ns Input timing reference levels.................................1.5V Output reference levels.........................................1.5V Output load................................................See Figure 1 NOTES: Vz is programmable from -2V to + 7V. IOL and IOH programmable from 0 to 16 mA. Vz is typically the midpoint of VOH and VOL. IOL and IOH are adjusted to simulate a typical resistive load circuit. End O f Life IOL Current Source Device Under Test + + Vz = 1.5V (Bipolar Supply) Ceff = 50pf Current Source IOH Figure 1 ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS (-55oC < TA < +125oC or -40oC to +85oC; Vcc = 5V +10%) DESCRIPTION Address to Output Delay CE\ to Output Delay OE\ to Output Delay Address to Output Hold CE\ or OE\ high to Output Float (1) RES\ low to Output Float (1) RES\ to Output Delay TEST CONDITIONS CE\ = OE\ = VIL, WE\ = VIH OE\ = VIL, WE\ = VIH OE\ = VIL, WE\ = VIH CE\ = OE\ = VIL, WE\ = VIH OE\ = VIL, WE\ = VIH CE\ = OE\ = VIL, WE\ = VIH CE\ = OE\ = VIL, WE\ = VIH 150 SYMBOL tACC tCE tOE tOH tDF tDFR tRR 10 0 0 0 0 50 350 450 MIN MAX 150 150 75 UNITS ns ns ns ns ns ns ns AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 5 EEPROM Austin Semiconductor, Inc. AS8ER128K32 ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC WRITE CHARACTERISTICS (-55oC < TA < +125oC; Vcc = 5V +10%) SYMBOL tAS tAH tCS tCH tWS tWH tOES tOEH tDS tDH tWP tCW tDL tBLC tBL tWC tDB tDW tRP tRES PARAMETER Address Setup Time Address Hold Time CE\ to Write Setup Time (WE\ controlled) CE\ Hold Time (WE\ controlled) WE\ to Write Setup Time (CE\ controlled) WE\ to Hold Time (CE\ controlled) OE\ to Write Setup Time OE\ to Hold Time Data Setup Time MIN 0 (2) MAX UNITS ms ns ns ns ns ns ns ns ns 150 0 0 0 0 0 0 100 10 End O f Life Data Hold Time ns WE\ Pulse Width (WE\ controlled) CE\ Pulse Width (CE\ controlled) 250 ns 250 ns Data Latch Time Byte Load Cycle 300 ns 0.55 100 30 s Byte Load Window Write Cycle Time s 10 (3) ms ns Time to Device Busy Write Start Time 120 150 (4) ns Reset Protect Time 100 1 s Reset High Time (5) s READ TIMING WAVEFORM ADDRESS CE\ t ACC tCE tOE t DF t OH OE\ WE\ Data Out VIH HIGH-Z tRR DATA OUT VALID t DFR RES\ AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 6 EEPROM Austin Semiconductor, Inc. AS8ER128K32 BYTE WRITE TIMING WAVEFORM (WE\ CONTROLLED) tWC Address tCS CE\ WE\ tAS t WP tOES OE\ Din t OEH tDS t DH tBL t AH t CH RDY/Busy\ RES\ VCC Address End O f Life t DB t DW HIGH-Z tRES t RP VOL HIGH-Z BYTE WRITE TIMING WAVEFORM (CE\ CONTROLLED) tWS t AH tCW tAS t WH t OEH tDS t DH t DB HIGH-Z tRES t RP VOL t DW tBL tWC CE\ WE\ tOES OE\ Din RDY/Busy\ HIGH-Z RES\ VCC AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 7 EEPROM Austin Semiconductor, Inc. AS8ER128K32 PAGE WRITE TIMING WAVEFORM (WE\ CONTROLLED) Address(6) A0 to A16 WE\ CE\ tCS tOES OE\ Din HIGH-Z tDS t DH HIGH-Z t DW tAS t AH tWP t DL t CH tBLC tBL tWC t OEH RDY/Busy\ RES\ VCC End O f Life t DB t RP tRES PAGE WRITE TIMING WAVEFORM (CE\ CONTROLLED) Address(6) A0 to A16 CE\ WE\ tAS tWS tOES t AH tCW tDL t WH tBLC tBL tWC t OEH OE\ Din RDY/Busy\ t RP HIGH-Z tDS t DH HIGH-Z t DW t DB RES\ VCC AS8ER128K32 Rev. 4.5 2/03 tRES Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 8 EEPROM Austin Semiconductor, Inc. AS8ER128K32 DATA POLLING TIMING WAVEFORM Address CE\ An An WE\ t OEH OE\ tCE(7) I\O7 End O f Life tOE(7) tDW Din X Dout X Dout X tOES tWC NOTES: 1. tDF and tDFR are defined as the time at which the outputs achieve the open circuit conditions and are no longer driven. 2. Use this device in longer cycle than this value. 3. tWC must be longer than this value unless polling techniques or RDY/Busy\ are used. This device automatically completes the internal write operation within this value. 4. Next read or write operation can be initiated after tDW if polling techniques or RDY/Busy\ are used. 5. This parameter is sampled and not 100% tested. 6. A7 to A16 are page addresses and must be same within the page write operation. 7. See AC read characteristics. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 9 EEPROM Austin Semiconductor, Inc. TOGGLE BIT This device provides another function to determine the internal programming cycle. If the EEPROM is set to read mode during the internal programming cycle, I/O6 will charge from "1" to "0" (toggling) for each read. When the internal programming cycle is finished, toggling of I/O6 will stop and the device can be accessible for next read or program. AS8ER128K32 TOGGLE BIT WAVEFORM Address CE\ tCE3 4 Next Mode WE\ OE\ I/O6 NOTES: 1) I/O6 beginning state is "1". 2) I/O6 ending state will vary. 3) See AC read characteristics. 4) Any locations can be used, but the address must be fixed. End O f Life tOE3 t OEH tOES Din Dout 1 Dout Dout 2 Dout 2 t DW tWC SOFTWARE DATA PROTECTION TIMING WAVEFORM (In protection mode) VCC CE\ WE\ Address Data (each byte) 5555 AA AAAA or 2AAA 55 5555 A0 * During this write cycle, data is physically written to the address provided. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 10 { Write Data tBLC tBLC tBLC tWC Write Address* EEPROM Austin Semiconductor, Inc. AS8ER128K32 SOFTWARE DATA PROTECTION TIMING WAVEFORM (In non-protection mode) VCC CE\ tWC Normal active mode WE\ Address 5555 AAAA or 2AAA 55 5555 5555 AAAA or 2AAA AA 55 5555 Data (each byte) FUNCTIONAL DESCRIPTION Automatic Page Write Page-mode write feature allows 1 to 128 bytes of data to be written into the EEPROM in a single write cycle. Following the initial byte cycle, an additional 1 to 128 bytes can be written in the same manner. Each additional byte load cycle must be started within 30s from the preceding falling edge of WE\ or CE\. When CE\ or WE\ is kept high for 100s after data input, the EEPROM enters write mode automatically and the input data are written into the EEPROM. DATA\ Polling DATA\ polling allows the status of the EEPROM to be determined. If EEPROM is set to read mode during the write cycle, an inversion of the last byte of data to be loaded outputs from I/O's 7, 15, 23, and 31 to indicate that the EEPROM is performing a write operation. End O f Life AA 80 20 RES\ Signal Diagram VCC Read inhibit Read inhibit RDY/Busy\ Signal RDY/Busy\ signal also allows status of the EEPROM to be determined. The RDY/Busy\ signal has high impedance except in write cycle and is lowered to VOL after the first write signal. At the end of write cycle, the RDY/Busy\ signal changes state to high impedance. RES\ Signal When RES\ is low, the EEPROM cannot be read or programmed. Therefore, data can be protected by keeping RES\ low when VCC is switched. RES\ should be high during read and programming because it doesn't provide a latch function. See timing diagram below. RES\ Program inhibit Program inhibit AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 11 EEPROM Austin Semiconductor, Inc. WE\, CE\ Pin Operation During a write cycle, address are latched by the falling edge of WE\ or CE\, and data is latched by the rising edge of WE\ or CE\. Write/Erase Endurance and Data Retention Time The endurance is 104 cycles in case of the page programming and 103 cycles in case of the byte programming (1% cumulative failure rate). The data retention time is more than 10 years when a device is page-programmed less than 104 cycles. AS8ER128K32 has a noise cancellation function that cuts noise if its width is 20ns or less in program mode. Be careful not to allow noise of a width more than 20ns on the control pins. See Diagram 1 below. 2. Data Protection at VCC On/Off When VCC is turned on or off, noise on the control pins generated by external circuits (CPU, etc.) may act as a trigger and turn the EEPROM to program mode by mistake. To prevent this unintentional programming, the EEPROM must be kept in an unprogrammable state while the CPR is in an unstable state. NOTE: The EEPROM should be kept in unprogrammable state during VCC on/off by using CPU RESET signal. See the timing diagram below. RDY/Busy\ SIGNAL RDY/Busy\ signal also allows status of the EEPROM to be determined. The RDY/Busy\ signal has high impedance except in write cycle and is lowered to VOL after the first write signal. At the end of the write cycle, the RDY/Busy\ signal changes state to high impedance. This allows many 58C1001 devices RDY/Busy\ signal lines to be wired-OR together. PROGRAMMING/ERASE The 58C1001 does NOT employ a BULK-erase function. The memory cells can be programmed `0' or `1'. A write cycle performs the function of erase & write on every cycle with the erase being transparent to the user. The internal erase data state is considered to be `1'. To program the memory array with background of ALL 0's or All 1's, the user would program this data using the page mode write operation to program all 1024 128-byte pages. Data Protection 1. Data Protection against Noise on Control Pins (CE\, OE\, WE\) During Operation During readout or standby, noise on the control pins may act as a trigger and turn the EEPROM to programming mode by mistake. To prevent this phenomenon, this device End O f Life DIAGRAM 1 DATA PROTECTION AT VCC ON/OFF VCC CPU RESET *Unprogrammable *Unprogrammable AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 12 EEPROM Austin Semiconductor, Inc. Data Protection Cont. a. Protection by RES\ The unprogrammable state can be realized by the CPU's reset signal inputs directly to the EEPROM's RES pin. RES should be kept VSS level during VCC on/off. The EEPROM brakes off programming operation when RES becomes low, programming operation doesn't finish correctly in case that RES falls low during programming operation. RES should be kept high for 10ms after the last data inputs. See the timing diagram below. 3. Software data protection To prevent unintentional programming, this device has the software data protection (SDP) mode. The SDP is enabled by inputting the 3 bytes code and write data in Chart 1. SDP is not enabled if only the 3 bytes code is input. AS8ER128K32 End O f Life PROTECTION BY RES\ VCC RES\ Program inhibit Program inhibit To program data in the SDP enable mode, 3 bytes code must be input before write data. This 4th cycle during write is required to initiate the SDP and physically writes the address and data. While in SDP the entire array is protected in which writes can only occur if the exact SDP sequence is re-executed or the unprotect sequence is executed. The SDP is disabled by inputting the 6 bytes code in Chart 2. Note that, if data is input in the SDP disable cycle, data can not be written. The software data protection is not enabled at the shipment. NOTE: These are some differences between ASI's and other company's for enable/disable sequence of software data protection. If these are any questions, please contact ASI. WE\ or CE\ 1 min 100 min 10 ms min CHART 1 Address 5555 AAAA or 2AAA 5555 Write Address Data (each Byte) CHART 2 Address 5555 AAAA or 2AAA 5555 5555 AAAA or 2AAA 5555 Data (each Byte) AA 55 A0 Write Data} Normal data input AA 55 80 AA 55 20 AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 13 EEPROM Austin Semiconductor, Inc. AS8ER128K32 MECHANICAL DEFINITIONS* ASI Case #703 (Package Designator Q) 4 x D2 4 x D1 4xD DETAIL A R End O f Life Pin 1 0o - 7o A2 B b L1 SEE DETAIL A e A1 D3 A SYMBOL A A1 A2 b B D D1 D2 D3 e R L1 ASI PACKAGE SPECIFICATIONS MIN MAX 0.123 0.200 0.118 0.186 0.000 0.020 0.013 0.017 0.010 REF 0.800 BSC 0.870 0.890 0.980 1.000 0.936 0.956 0.050 BSC 0.005 0.035 0.045 *All measurements are in inches. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 14 EEPROM Austin Semiconductor, Inc. AS8ER128K32 MECHANICAL DEFINITIONS* ASI Case (Package Designator QB) End O f Life 0.900 0.020 0.320 0.200 0.015 0.050 DETAIL A 0.035(+0.005) 0.008(+0.002) 0.015(+0.005) *All measurements are in inches. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 15 EEPROM Austin Semiconductor, Inc. AS8ER128K32 ORDERING INFORMATION EXAMPLE: AS8ER128K32Q-15/IT End O f Life Device Number AS8ER128K32 AS8ER128K32 AS8ER128K32 Process /* /* /* EXAMPLE: AS8ER128K32QB-250/XT Device Number AS8ER128K32 AS8ER128K32 AS8ER128K32 Package Type QB QB QB Speed ns -150 -200 -250 Process /* /* /* Package Type Q Q Q Speed ns -150 -200 -250 *AVAILABLE PROCESSES IT = Industrial Temperature Range XT = Extended Temperature Range 883C = Full Military Processing -40oC to +85oC -55oC to +125oC -55oC to +125oC AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 16 EEPROM Austin Semiconductor, Inc. AS8ER128K32 ASI TO DSCC PART NUMBER CROSS REFERENCE* Package Designator Q ASI Part # AS8ER128K32Q-250/883C AS8ER128K32Q-200/883C AS8ER128K32Q-150/883C SMD Part 5962-9458507HMX 5962-9458508HMX 5962-9458509HMX End O f Life Package Designator QB ASI Part # AS8ER128K32QB-250/883C AS8ER128K32QB-200/883C AS8ER128K32QB-150/883C SMD Part 5962-9458507HZC 5962-9458508HZC 5962-9458509HZC * ASI part number is for reference only. Orders received referencing the SMD part number will be processed per the SMD. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 17 |
Price & Availability of AS8ER128K3203
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |