 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MICROWAVE CORPORATION v02.0304 HMC446 GaAs MMIC 10W T/R SWITCH, 824 - 894 MHz* Features Low Insertion Loss: 0.6 dB High IIP3: +65 dBm High Input P0.1 dB: +40 dBm Tx Positive Control: 0/+5V to 0/+8V Ultra Small Package: SOT26 Typical Applications The HMC446 is ideal for: * ISM/Cellular Portables/Handsets * Automotive Telematic Applications * Mobile Radio Functional Diagram General Description The HMC446 is a low-cost SPDT switch in a 6-lead SOT26 package for use in transmit-receive applications which require very low distortion at high signal power levels, up to 10 watts. The device can control signals from 824 - 894 MHz* and is especially suited for cellular booster and automotive telematic applications. The design provides exceptional P0.1 dB of +40 dBm and +65 dBm IIP3 on the Transmit (Tx) port. The Tx port is a reflective open when "Off" while the Rx port is a reflective short when "Off". On-chip circuitry allows single positive supply operation at very low DC current with a single control input (Vctl). 14 SWITCHES - SMT Electrical Specifications, TA = +25 C, Vctl = 0/+8 Vdc, 50 Ohm System Parameter Insertion Loss Tx - RFC RFC - Rx Tx - RFC RFC - Rx Tx - RFC RFC - Rx Tx - RFC RFC - Rx Tx - RFC RFC - Rx Frequency* 824 - 849 MHz 824 - 894 MHz 824 - 849 MHz 824 - 894 MHz 824 - 849 MHz 824 - 894 MHz 824 - 849 MHz 824 - 894 MHz 824 - 849 MHz 824 - 894 MHz 824 - 894 MHz tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 4 90 ns ns 38 28 18 29 Min. Typ. 0.6 0.6 22 35 13 17 40 30 65 52 Max. 0.9 1.0 Units dB dB dB dB dB dB dBm dBm dBm dBm Isolation Return Loss Input Power for 0.1 dB Compression Input Third Order Intercept (Two-tone input power = +19 dBm each tone) Switching Characteristics * External component values can be adjusted to enable HMC446 to operate in other frequency bands. Contact HMC with your specific requirement. 14 - 254 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v02.0304 HMC446 GaAs MMIC 10W T/R SWITCH, 824 - 894 MHz* Insertion Loss vs. Temperature, Tx 0 -0.5 Insertion Loss vs. Temperature, Rx 0 -0.5 INSERTION LOSS (dB) INSERTION LOSS (dB) -1 -1.5 -2 Tx, +25C -1 -1.5 -2 Rx, +25C -2.5 -3 0.75 Tx, +85C Tx, -40C -2.5 -3 0.75 Rx, +85C Rx, -40C 0.8 0.85 0.9 0.8 0.85 0.9 FREQUENCY (GHz) FREQUENCY (GHz) Isolation 0 -5 -10 RFC to Tx RFC to Rx Return Loss 0 Tx, Input Tx, Output Rx, Input Rx, Output -5 14 SWITCHES - SMT 14 - 255 -15 -20 -25 -30 -35 -40 0.75 RETURN LOSS (dB) ISOLATION (dB) -10 -15 -20 0.8 0.85 0.9 -25 0.75 0.8 0.85 0.9 FREQUENCY (GHz) FREQUENCY (GHz) Input Power Compression @ 849 MHz, Vdd = 8.0V 0 Input Power Compression @ 849 MHz, Vdd = 5.0V 0 INSERTION LOSS (dB) INSERTION LOSS (dB) -0.5 -0.5 -1 -1 -1.5 Tx Rx -1.5 Tx Rx -2 10 15 20 25 30 35 40 INPUT POWER (dBm) -2 10 15 20 25 30 35 40 INPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0304 MICROWAVE CORPORATION HMC446 GaAs MMIC 10W T/R SWITCH, 824 - 894 MHz* Absolute Maximum Ratings Max. Input Power (Vdd = +8V, VCTL = 0/+8V) Supply Voltage (Vdd) Control Voltage Range (Vctl) Storage Temperature Operating Temperature Tx Port Rx Port 41 dBm 33 dBm +10 Vdc Truth Table Control Input Vctl (Vdc) 0.0 Signal Path State Tx to RFC OFF ON RFC to Rx ON OFF -0.2 to Vdd Vdd -65 to +150 C -40 to +85 C Vdd = +5.0V to +8.0V 0.2V Control Input Voltage Tolerances are 0.2 Vdc. Do not operate continuously at power levels > 1 dB compression and do not "hot switch" power levels greater than +36 dBm (Vctl= +8V) into the Tx port and no greater than +27 dBm into the Rx port. DC blocking capacitors are required at ports RFC, Tx and Rx. Inductors are required from Tx to RFC and Rx to RFC. See Application Circuit Herein. 14 SWITCHES - SMT Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEADFRAME MATERIAL: COPPER ALLOY 3. LEADFRAME PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 14 - 256 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0304 MICROWAVE CORPORATION HMC446 GaAs MMIC 10W T/R SWITCH, 824 - 894 MHz* Pin Descriptions Pin Number Function Description Interface Schematic 1 Tx This pin is DC coupled and matched to 50 Ohms. 2 GND This pin must be connected to PCB RF ground. 3 Vctl See Truth Table. 4 Rx This pin is DC coupled and matched to 50 Ohms. 14 5 Vdd Supply Voltage 6 RFC This pin is DC coupled and matched to 50 Ohms. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 14 - 257 SWITCHES - SMT v02.0304 MICROWAVE CORPORATION HMC446 GaAs MMIC 10W T/R SWITCH, 824 - 894 MHz* Required Application Circuit 14 Users must implement this application circuit with the HMC446 T/R switch for proper operation. Note 1: LRx = COILCRAFT 0402CS - 8N2XJB, 8.2 nH, 5% Tolerance Inductor Note 2: LTx = COILCRAFT 0603CS - 22NXJB, 22 nH, 5% Tolerance Inductor Note 3: C1, C2, C3 = 330 pF Capacitor Note 4: External component values can be adjusted to enable HMC446 to operate in other frequency bands. Contact HMC with your specific requirement. Note 5: Set logic gate & switch Vdd= +8V and use HC series logic to provide a buffered logic interface. SWITCHES - SMT 14 - 258 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v02.0304 MICROWAVE CORPORATION HMC446 GaAs MMIC 10W T/R SWITCH, 824 - 894 MHz* Evaluation PCB 14 List of Material Item J1 - J3 J4 - J6 C1 - C3 LTx LRx U1 PCB* Description PC Mount SMA RF Connector DC Pin 330 pF Capacitor, 0603 Pkg. 22 nH Inductor, 0603 Pkg. 8.2 nH Inductor, 0402 Pkg. HMC446 T/R Switch 103835 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown above. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board as shown is available from Hittite upon request. * Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 14 - 259 SWITCHES - SMT |
Price & Availability of HMC446
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |