View MB15F73UVPVB_1274431.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FUJITSU SEMICONDUCTOR DATA SHEET
DS04-21376-2E
ASSP
Dual Serial Input PLL Frequency Synthesizer
MB15F73UV
s DESCRIPTION
The Fujitsu MB15F73UV is a serial input Phase Locked Loop (PLL) frequency synthesizer with a 2250 MHz and a 600 MHz prescalers. A 64/65 or a 128/129 for the 2250 MHz prescaler, and a 8/9 or a 16/17 for the 600 MHz prescaler can be selected for the prescaler that enables pulse swallow operation. The BiCMOS process is used, as a result a supply current is typically 3.2 mA at 2.7 V. The supply voltage range is from 2.4 V to 3.6 V. A refined charge pump supplies well-balanced output current with 1.5 mA and 6 mA selectable by serial data. The data format is the same as the previous one MB15F03SL, MB15F73SP/UL. Fast locking is achieved for adopting the new circuit. MB15F73UV is in the new small package (BCC18), which decreases a mount area of MB15F73UV about 50% comparing with the former BCC20 (for dual PLL) . MB15F73UV is ideally suited for wireless mobile communications, such as CDMA and PCS.
s FEATURES
* High frequency operation : RF synthesizer : 2250 MHz Max : IF synthesizer : 600 MHz Max * Low power supply voltage : VCC = 2.4 V to 3.6 V * Ultra low power supply current : ICC = 3.2 mA Typ (VCC = 2.7 V, Ta = +25 C, SWIF = SWRF = 0 in IF/RF locking state) (Continued)
s PACKAGES
18-pin plastic BCC
(LCC-18P-M05)
MB15F73UV
(Continued) * Direct power saving function : Power supply current in power saving mode Typ 0.1 A (VCC = 2.7 V, Ta = +25 C) Max 10 A (VCC = 2.7 V) * Software selectable charge pump current : 1.5 mA/6.0 mA Typ * Dual modulus prescaler : 2250 MHz prescaler (64/65 or128/129) /600 MHz prescaler (8/9 or 16/17) * 23 bit shift register * Serial input binary 14-bit programmable reference divider : R = 3 to 16,383 * Serial input programmable divider consisting of: - Binary 7-bit swallow counter : 0 to 127 - Binary 11-bit programmable counter : 3 to 2,047 * Built-in high-speed tuning, low-noise phase comparator, current-switching type constant current circuit * On-chip phase control for phase comparator * On-chip phase comparator for fast lock and low noise * Built-in digital locking detector circuit to detect PLL locking and unlocking * Operating temperature : Ta = -40 C to +85 C * Serial data format compatible with MB15F73UL * Ultra small Package Bcc18 (2.4 mm x 2.7 mm x 0.45 mm)
s PIN ASSIGNMENTS
(BCC-18) TOP VIEW
Clock OSCIN Data GND finIF XfinIF GNDIF VCCIF DOIF 1 2 3 4 5 6 7 8 9 18 17 16 15 14 13 12 11 10 LE finRF XfinRF GNDRF VCCRF DORF
PSIF PSRF LD/fout
(LCC-18P-M05)
2
MB15F73UV
s PIN DESCRIPTION
Pin no. BCC 1 2 3 4 5 6 7 Pin name GND finIF XfinIF GNDIF VCCIF DoIF PSIF I/O I I O I Descriptions Ground pin for OSC input buffer and the shift register circuit. Prescaler input pin for the IF-PLL. Connection to an external VCO should be AC coupling. Prescaler complimentary input for the IF-PLL section. This pin should be grounded via a capacitor. Ground pin for the IF-PLL section. Power supply voltage input pin for the IF-PLL section, the shift register and the oscillator input buffer. Charge pump output for the IF-PLL section. Power saving mode control pin for the IF-PLL section. This pin must be set at "L" when the power supply is started up. (Open is prohibited.) PSIF = "H" ; Normal mode/PSIF = "L" ; Power saving mode Lock detect signal output (LD) /phase comparator monitoring output (fout) pin. The output signal is selected by LDS bit in a serial data. LDS bit = "H" ; outputs fout signal/LDS bit = "L" ; outputs LD signal Power saving mode control for the RF-PLL section. This pin must be set at "L" when the power supply is started up. (Open is prohibited. ) PSRF = "H" ; Normal mode/PSRF = "L" ; Power saving mode Charge pump output for the RF-PLL section. Power supply voltage input pin for the RF-PLL section. Ground pin for the RF-PLL section Prescaler complimentary input pin for the RF-PLL section. This pin should be grounded via a capacitor. Prescaler input pin for the RF-PLL. Connection to an external VCO should be via AC coupling. Load enable signal input pin (with the schmitt trigger circuit) When LE is set "H", data in the shift register is transferred to the corresponding latch according to the control bit in a serial data. Serial data input pin (with the schmitt trigger circuit) Data is transferred to the corresponding latch (IF-ref. counter, IF-prog. counter, RF-ref. counter, RF-prog. counter) according to the control bit in a serial data. Clock input pin for the 23-bit shift register (with the schmitt trigger circuit) One bit data is shifted into the shift register on a rising edge of the clock. The programmable reference divider input pin. TCXO should be connected with an AC coupling capacitor.
8
LD/fout
O
9 10 11 12 13 14
PSRF DoRF VCCRF GNDRF XfinRF finRF
I O I I
15
LE
I
16
Data
I
17 18
Clock OSCIN
I I
3
MB15F73UV
s BLOCK DIAGRAM
VCCIF GNDIF 5 4
PSIF 7
SWIF
LDS
FCIF
Intermittent mode control (IF-PLL)
3 bit latch
7 bit latch
11 bit latch Phase comp. (IF-PLL) Charge pump Current (IF-PLL) Switch 6 DoIF
Binary 7-bit Binary 11-bit swallow counter programmable (IF-PLL) counter (IF-PLL)
fpIF finIF 2 XfinIF 3 Prescaler (IF-PLL) (8/9, 16/17) 2 bit latch T1 T2 14 bit latch Binary 14-bit programmable ref. counter(IF-PLL) frIF OSCIN 18 Fast lock Tuning frRF T1 OR 2 bit latch finRF 14 XfinRF 13
Prescaler (RF-PLL) (64/65, 128/129)
Lock Det. (IF-PLL) 1 bit latch C/P setting counter LDIF
AND
C/P setting counter
Selector
T2
Binary 14-bit programmable ref. counter (RF-PLL))
14 bit latch
1 bit latch LDRF fpRF Lock Det. (RF-PLL)
LD frIF frRF fpIF fpRF
8 LD/ fout
PSRF 9
Intermittent mode control (RF-PLL)
Binary 11-bit Binary 7-bit swallow counter programmable counter (RF-PLL) (RF-PLL)
Phase comp. (RF-PLL)
Fast lock Tuning
Charge Current pump Switch (RF-PLL)
SWRF
FCRF
LDS
10 DoRF
fpRF
3 bit latch
7 bit latch
11 bit latch
LE 15
Schmitt circuit
Latch selector
Data 16 Clock 17
Schmitt circuit Schmitt circuit
CC NN 12
23-bit shift register
1 GND
11
12
VCCRF GNDRF
4
MB15F73UV
s ABSOLUTE MAXIMUM RATINGS
Parameter Power supply voltage Input voltage Output voltage Storage temperature LD/fout DoIF, DoRF Symbol VCC VI VO VDO Tstg Rating Min -0.5 -0.5 GND GND -55 Max 4.0 VCC + 0.5 VCC VCC +125 Unit V V V V C
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
s RECOMMENDED OPERATING CONDITIONS
Parameter Power supply voltage Input voltage Operating temperature Symbol VCC VI Ta Value Min 2.4 GND -40 Typ 2.7 Max 3.6 VCC +85 Unit V V C Remarks VCCRF = VCCIF
Notes : * VCCRF, VCCIF must supply equal voltage. Even if either RF-PLL or IF-PLL is not used, power must be supplied to VCCRF, VCCIF to keep them equal. It is recommended that the non-use PLL is controlled by power saving function. * Although this device contains an anti-static element to prevent electrostatic breakdown and the circuitry has been improved in electrostatic protection, observe the following precautions when handling the device. * When storing and transporting the device, put it in a conductive case. * Before handling the device, confirm the (jigs and) tools to be used have been uncharged (grounded) as well as yourself. Use a conductive sheet on working bench. * Before fitting the device into or removing it from the socket, turn the power supply off. * When handling (such as transporting) the device mounted board, protect the leads with a conductive sheet. WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand.
5
MB15F73UV
s ELECTRICAL CHARACTERISTICS
*
(VCC = 2.4 V to 3.6 V, Ta = -40 C to +85 C) Parameter Symbol ICCIF *1 Power supply current ICCRF *1 Power saving current finIF *3 Operating frequency finRF * finIF finRF
3
Condition finIF = 480 MHz VCCIF = 2.7 V finRF = 2000 MHz VCCRF = 2.7 V PSIF = PSRF = "L" PSIF = PSRF = "L" IF PLL RF PLL IF PLL, 50 system RF PLL, 50 system Schmitt triger input Schmitt triger input VCC = 2.7 V, IOH = -1 mA VCC = 2.7 V, IOL = 1 mA VCC = 2.7 V, IDOH = -0.5 mA VCC = 2.7 V, IDOL = 0.5 mA VCC = 2.7 V VOFF = 0.5 V to Vcc - 0.5 V VCC = 2.7 V VCC = 2.7 V
Value Min 0.8 1.3 50 200 3 -15 -15 0.5 0.7 VCC + 0.4 0.7 VCC -1.0 -1.0 VCC - 0.4 VCC - 0.4 1.0 Typ 1.2 2.0 0.1 *2 0.1 *2 Max 1.7 2.8 10 10 600 2250 40 +2 +2 1.5 0.3 VCC - 0.4 0.3 VCC +1.0 +1.0 0.4 0.4 2.5 -1.0
Unit mA mA A A MHz MHz MHz dBm dBm VP-P V V V V A A V V V V nA mA mA
IPSIF IPSRF finIF finRF fOSC PfinIF PfinRF VOSC VIH VIL VIH VIL IIH *4 IIL *4 VOH VOL VDOH VDOL IOFF IOH *4 IOL
OSCIN Input sensitivity
Input available voltage OSCIN "H" level input voltage "L" level input voltage "H" level input voltage "L" level input voltage "H" level input current "L" level input current Data LE Clock PSIF PSRF Data LE Clock PS
"H" level output voltage LD/ "L" level output voltage fout "H" level output voltage DoIF "L" level output voltage DoRF High impedance cutoff DoIF current DoRF "H" level output current LD/ "L" level output current fout
(Continued)
6
MB15F73UV
(Continued)
(VCC = 2.4 V to 3.6 V, Ta = -40 C to +85 C) Symbol Condition VCC = 2.7 V, VDOH = Vcc / 2, Ta = +25 C VCC = 2.7 V, VDOL = Vcc / 2, Ta = +25 C VDO = Vcc / 2 0.5 V VDO Vcc - 0.5 V -40 C Ta +85 C, VDO = Vcc / 2 CS bit = "1" CS bit = "0" CS bit = "1" CS bit = "0" Value Min -8.2 -2.2 4.1 0.8 Typ -6.0 -1.5 6.0 1.5 3 10 5 Max -4.1 -0.8 8.2 2.2 Unit mA mA mA mA % % %
Parameter "H" level output current "L" level output current DoIF *8 DoRF DoIF *8 DoRF
IDOH *4
IDOL
IDOL/IDOH IDOMT *5 Charge pump current rate vs VDO vs Ta IDOVD *
6
IDOTA *7
*1 : Conditions ; fosc = 12.8 MHz, Ta = +25 C, SW = "0" in locking state. *2 : VCCIF = VCCRF = 2.7 V, fosc = 12.8 MHz, Ta = +25 C, in power saving mode. PSIF = PSRF = GND VIH = VCC, VIL = GND (at CLK, Data, LE) *3 : AC coupling. 1000 pF capacitor is connected under the condition of Min operating frequency. *4 : The symbol "-" (minus) means the direction of current flow. *5 : VCC = 2.7 V, Ta = +25 C (||I3| - |I4||) / [ (|I3| + |I4|) / 2] x 100 (%) *6 : VCC = 2.7 V, Ta = +25 C [ (||I2| - |I1||) / 2] / [ (|I1| + |I2|) / 2] x 100 (%) (Applied to both lDOL and lDOH) *7 : VCC = 2.7 V, [||IDO (+85 C) | - |IDO (-40 C) || / 2] / [|IDO (+85 C) | + |IDO (-40 C) | / 2] x 100 (%) (Applied to both IDOL and IDOH) *8 : When Charge pump current is measured, set LDS = "0" , T1 = "0" and T2 = "1".
I1 IDOL
I3 I2
IDOH
I2
I4 I1 0.5 VCC/2 VCC - 0.5 VCC
Charge pump output voltage (V)
7
MB15F73UV
s FUNCTIONAL DESCRIPTION
1. Pulse swallow function
fVCO = [ (P x N) + A] x fOSC / R fVCO : Output frequency of external voltage controlled oscillator (VCO) P : Preset divide ratio of dual modulus prescaler (8 or 16 for IF-PLL, 64or 128 for RF-PLL) N : Preset divide ratio of binary 11-bit programmable counter (3 to 2,047) A : Preset divide ratio of binary 7-bit swallow counter (0 A 127, A < N) fOSC : Reference oscillation frequency (OSCIN input frequency) R : Preset divide ratio of binary 14-bit programmable reference counter (3 to 16,383)
2. Serial Data Input
The serial data is entered using three pins, Data pin, Clock pin, and LE pin. Programmable dividers of IF/RFPLL sections, programmable reference dividers of IF/RF-PLL sections are controlled individually. The serial data of binary data is entered through Data pin. On rising edge of Clock, one bit of the serial data is transferred into the shift register. On a rising edge of load enable signal, the data stored in the shift register is transferred to one of latches depending upon the control bit data setting. The programmable The programmable reference counter reference counter for the IF-PLL for the RF-PLL CN1 CN2 0 0 1 0 The programmable counter and the swallow counter for the IF-PLL 0 1 The programmable counter and the swallow counter for the RF-PLL 1 1
(1) Shift Register Configuration * Programmable Reference Counter
1
2
3
4
5
6
7
8
9
10 11 12 13
14
15
16
17
18
19 20 21 22 23 X X X
CN1 CN2 T1 T2 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 CS X
CS R1 to R14 T1, T2 CN1, CN2 X
: Charge pump current select bit : Divide ratio setting bits for the programmable reference counter (3 to 16,383) : LD/fout output setting bit : Control bit : Dummy bits (Set "0" or "1")
Note : Data input with MSB first.
8
MB15F73UV
* Programmable Counter
1
2
3
4 SWIF/
RF
5 FCIF/
RF
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22
23
CN1 CN2 LDS
A1 A2 A3 A4 A5 A6 A7 N1 N2 N3 N4 N5 N6 N7 N8 N9 N10 N11
A1 to A7 N1 to N11 LDS SWIF/RF FCIF/RF CN1, 2
: Divide ratio setting bits for the swallow counter (0 to 127) : Divide ratio setting bits for the programmable counter (3 to 2,047) : LD/fout signal select bit : Divide ratio setting bit for the prescaler (IF : SWIF, RF : SWRF) : Phase control bit for the phase detector (IF : FCIF, RF : FCRF) : Control bit
Note : Data input with MSB first.
(2) Data setting * Binary 14-bit Programmable Reference Counter Data Setting Divide ratio 3 4 * * * 16383 R14 R13 R12 R11 R10 R9 0 0 * * * 1 0 0 * * * 1 0 0 * * * 1 0 0 * * * 1 0 0 * * * 1 0 0 * * * 1 R8 0 0 * * * 1 R7 0 0 * * * 1 R6 0 0 * * * 1 R5 0 0 * * * 1 R4 0 0 * * * 1 R3 0 1 * * * 1 R2 1 0 * * * 1 R1 1 0 * * * 1
Note : Divide ratio less than 3 is prohibited. * Binary 11-bit Programmable Counter Data Setting Divide ratio N11 N10 N9 3 4 * * * 2047 0 0 * * * 1 0 0 * * * 1 0 0 * * * 1 N8 0 0 * * * 1 N7 0 0 * * * 1 N6 0 0 * * * 1 N5 0 0 * * * 1 N4 0 0 * * * 1 N3 0 1 * * * 1 N2 1 0 * * * 1 N1 1 0 * * * 1
Note : Divide ratio less than 3 is prohibited * Binary 7-bit Swallow Counter Data Setting Divide ratio 0 1 * * * 127 A7 0 0 * * * 1 A6 0 0 * * * 1 A5 0 0 * * * 1 A4 0 0 * * * 1 A3 0 0 * * * 1 A2 0 0 * * * 1 A1 0 1 * * * 1 9
MB15F73UV
* Prescaler Data Setting Divide ratio Prescaler divide ratio IF-PLL Prescaler divide ratio RF-PLL * Charge Pump Current Setting Current value CS 6.0 mA 1.5 mA 1 0 SW = "1" 8/9 64/65 SW = "0" 16/17 128/129
* LD/fout output Selectable Bit Setting LD/fout pin state LD output frIF fout output frRF fpIF fpRF LDS 0 0 0 1 1 1 1 T1 0 1 1 0 1 0 1 T2 0 0 1 0 0 1 1
* Phase Comparator Phase Switching Data Setting Phase comparator input fr > fp fr < fp fr = fp Z : High-impedance Depending upon the VCO and LPF polarity, FC bit should be set. High
(1)
FCIF, FCRF = "1" DoIF, DoRF H L Z
FCIF, FCRF = "0" DoIF, DoRF L H Z
(1) VCO polarity FC = "1" (2) VCO polarity FC = "0"
VCO Output Frequency
(2)
LPF Output voltage
Max
Note : Give attention to the polarity for using active type LPF.
10
MB15F73UV
3. Power Saving Mode (Intermittent Mode Control Circuit)
Status Normal mode Power saving mode PS pin
H L
The intermittent mode control circuit reduces the PLL power consumption. By setting the PS pin low, the device enters into the power saving mode, reducing the current consumption. See the Electrical Characteristics chart for the specific value. The phase detector output, Do, becomes high impedance. For the dual PLL, the lock detector, LD, is as shown in the LD Output Logic table. Setting the PS pin high, releases the power saving mode, and the device works normally. The intermittent mode control circuit also ensures a smooth startup when the device returns to normal operation. When the PLL is returned to normal operation, the phase comparator output signal is unpredictable. This is because of the unknown relationship between the comparison frequency (fp) and the reference frequency (fr) which can cause a major change in the comparaor output, resulting in a VCO frequency jump and an increase in lockup time. To prevent a major VCO frequency jump, the intermittent mode control circuit limits the magnitude of the error signal from the phase detector when it returns to normal operation. Notes : * When power (VCC) is first applied, the device must be in standby mode, PS = Low, for at least 1 s. * Serial data input are done after the power supply becomes stable, and then the power saving mode is released after completed the data input.
OFF
ON tV 1 s
VCC Clock Data LE PS
tPS 100 ns
(1)
(2)
(3)
(1) PS = L (power saving mode) at Power-ON (2) Set serial data at least 1 s after the power supply becomes stable (VCC 2.2 V) . (3) Release power saving mode (PSIF, PSRF : "L" "H") at least 100 ns later after setting serial data.
11
MB15F73UV
4. Serial Data Data Input Timing
Divide ratio is performed through a serial interface using the Data pin, Clock pin, and LE pin. Setting data is read into the shift register at the rise of the Clock signal, and transferred to a latch at the rise of the LE signal. The following diagram shows the data input timing. 1st data Invalid data 2nd data
Control bit
Data
MSB
LSB
Clock
t1 t7 t2 t3 t6
LE
t4 t5
Parameter t1 t2 t3 t4
Min 20 20 30 30
Typ
Max
Unit ns ns ns ns
Parameter t5 t6 t7
Min 100 20 100
Typ
Max
Unit ns ns ns
Note : LE should be "L" when the data is transferred into the shift register.
12
MB15F73UV
s PHASE COMPARATOR OUTPUT WAVEFORM
frIF/RF
fpIF/RF
tWU
tWL
LD
(FC bit = 1)
H DoIF/RF Z L
(FC bit = 0)
DoIF/RF Z L H
* LD Output Logic IF-PLL section Locking state/Power saving state Locking state/Power saving state Unlocking state Unlocking state Notes : * * * * *
RF-PLL section Locking state/Power saving state Unlocking state Locking state/Power saving state Unlocking state
LD output H L L L
Phase error detection range = -2 to +2 Pulses on DoIF/RF signals during locking state are output to prevent dead zone. LD output becomes low when phase error is tWU or more. LD output becomes high when phase error is tWL or less and continues to be so for three cycles or more. tWU and tWL depend on OSCIN input frequency as follows. tWU 2/fosc : e.g. tWU 156.3 ns when fosc = 12.8 MHz tWU 4/fosc : e.g. tWL 312.5 ns when fosc = 12.8 MHz
13
MB15F73UV
s TEST CIRCUIT (for Measuring Input Sensitivity fin/OSCIN)
S.G. 1000 pF
50 S.G.
1000 pF
Controller (divide ratio setting)
Clock Data LE
50 OSCIN
GND S.G. 1 1000 pF finIF 50
1000 pF
18
17
16
15 14 13 finRF 1000 pF
VCCRF
2 XfinIF 3
MB15F73UV
4 12 11
XfinRF 0.1 F GNDRF
GNDIF 5 6 7 8 9 VCCRF VCCIF DoIF 10 DoRF
LD/ fout PSIF 0.1 F
PSRF
Oscilloscope
14
MB15F73UV
s TYPICAL CHARACTERISTICS
1. fin input sensitivity
RF-PLL input sensitivity vs. Input frequency characteristic
10
0
Catalog guaranteed range
-10
PfinRF (dBm)
-20
-30
-40
-50 0 500 1000 1500 2000 2500
VCC = 2.4 V VCC = 2.7 V VCC = 3.0 V VCC = 3.6 V spec 3000
finRF (MHz)
IF-PLL input sensitivity vs. Input frequency characteristic
10 0
Catalog guaranteed range
PfinIF (dBm)
-10 -20 -30 -40 -50 0 200 400 600 800 1000 VCC = 2.4 V VCC = 2.7 V VCC = 3.0 V VCC = 3.6 V SPEC
finIF (MHz)
15
MB15F73UV
2. OSCIN input sensitivity
Input sensitivity vs. Input frequency
10 0 -10 -20 -30 -40 -50 0 20 40 60 80 100 120 140 160 VCC = 2.4 V VCC = 2.7 V VCC = 3.0 V VCC = 3.6 V spec
Catalog guaranteed range
Input sensitivity VOSC (dBm)
Input frequency fOSC (MHz)
16
MB15F73UV
3. RF/IF-PLL Do output current
* CP = 1.5 mA Charge Pomp Output Voltage vs. Charge Pomp Output Current
2.50
Charge pomp output current IDO (mA)
2.00 1.50 1.00 0.50 0.00 -0.50 -1.00 -1.50 -2.00 -2.50 0.0
VCC = 2.7 V, Ta = +25C
0.5
1.0
1.5
2.0
2.5
3.0
Charge pomp output voltage VDO (V)
* CP = 6.0 mA Charge Pomp Output Voltage vs. Charge Pomp Output Current
8.00
Charge pomp output current IDO (mA)
VCC = 2.7 V, Ta = +25C 6.00 4.00 2.00 0.00 -2.00 -4.00 -6.00 -8.00 0.0 0.5 1.0 1.5 2.0 2.5 3.0
Charge pomp output voltage VDO (V)
17
MB15F73UV
4. fin input impedance
finIF input impedance
4 : 21.109 -146.41 1.8117 pF 600.000 000 MHz 1 : 927.81 -1.1572 k 50 MHz 2: 99.75 -453.91 200 MHz
3 : 34.141 -228.06 400 MHz
1 2 4 3
START 50.000 000 MHz
STOP 1 000.000 000 MHz
finRF input impedance
4 : 7.4382 2.5134 181.83 pH 2 200.000 000 MHz 1 : 17.516 -120.82 700 MHz 2 : 11.105 -57.764 1.2 GHz
4
3 : 8.8408 -25.122 1.7 GHz
3 2
1
START 200.000 000 MHz
STOP 2 250.000 000 MHz
18
MB15F73UV
5. OSCIN input impedance
OSCIN input impedance
4 : 272.06 -1.0519 k 3.7826 pF 40.000 000 MHz 1 : 2.2315 k -2.3139 k 10 MHz 2 : 858.38 -1.8481 k 20 MHz 3 : 437.13 -1.3529 k 30 MHz
4 1 2 3
START 3.000 000 MHz
STOP 40.000 000 MHz
19
MB15F73UV
s REFERENCE INFORMATION (for Lock-up Time, Phase Noise and Reference Leakage)
Test Circuit S.G. OSCIN Do fin 33 k Spectrum Analyzer VCO 2700 pF 6.2 k 0.027 F To VCO 680 pF LPF fVCO = 2113.6 MHz KV = 50 MHz/V fr = 50 kHz fOSC = 19.2 MHz LPF VCC = 2.7 V VVCO = 2.8 V Ta = + 25 C CP : 1.5 mA mode
* PLL Reference Leakage
ATTEN 10 dB RL 0 dBm VAVG 0 10 dB/ MKR -81.50 dB 50.0 kHz
MKR 50.0 kHz -81.50 dB
CENTER 2.1136000 GHz RBW 1.0 kHz VBW 1.0 kHz
SPAN 200.0 kHz SWP 500 ms
* PLL Phase Noise
ATTEN 10 dB RL 0 dBm VAVG 16 10 dB/ MKR -66.51 dB/Hz 1.00 kHz
MKR 1.0 kHz -66.51 dB/Hz
CENTER 2.11360000 GHz RBW 30 Hz VBW 30 Hz
SPAN 10.00 kHz SWP 1.92 s
(Continued)
20
MB15F73UV
(Continued)
PLL Lock Up time 2113.6 MHz2173.6 MHz 1 kHz L chH ch 1.80 ms
,Mkr x: 1.79999289 ms
y: 59.96897 MHz
100.0050 MHz
2.00 kHz/div
99.99500 MHz
0.00 s
4.0000000 ms
PLL Lock Up time 2173.6 MHz2113.6 MHz 1 kHz H chL ch 1.54 ms
,Mkr x: 1.54000169 ms
y: -59.9935 MHz
100.0050 MHz
2.00 kHz/div
99.99500 MHz
0.00 s
4.0000000 ms
21
MB15F73UV
s APPLICATION EXAMPLE
1000 pF
TCXO
Controller (divide ratio setting)
OSCIN Clock Data LE
OUTPUT
GND 1 1000 pF 2 finIF XfinIF 1000 pF 3 13 14 18 17 16 15 finRF 1000 pF
OUTPUT
VCO
1000 pF
MB15F73UV
4 12 11
XfinRF GNDRF VCCRF
VCO
GNDIF
LPF
VCCIF
5 6 7 8 9
LPF
VCCRF 10 DoRF PSIF PSRF
0.1 F
VCCIF
DoIF
0.1 F
LD/ fout Lock Detect
Note : Clock, Data, LE : The schmitt trigger circuit is provided (insert a pull-down or pull-up register to prevent oscillation when open-circuit in the input) .
22
MB15F73UV
s USAGE PRECAUTIONS
(1) VCCRF and VCCIF must be equal voltage. Even if either RF-PLL or IF-PLL is not used, power must be supplied to VCCRF, VpRF, VCCIF and VpIF to keep them equal. It is recommended that the non-use PLL is controlled by power saving function. (2) To protect against damage by electrostatic discharge, note the following handling precautions : -Store and transport devices in conductive containers. -Use properly grounded workstations, tools, and equipment. -Turn off power before inserting or removing this device into or from a socket. -Protect leads with conductive sheet, when transporting a board mounted device
s ORDERING INFORMATION
Part number MB15F73UVPVB Package 18-pin plastic BCC (LCC-18P-M05) Remarks
23
MB15F73UV
s PACKAGE DIMENSIONS
18-pin plastic BCC (LCC-18P-M05)
2.31(.090) TYP 0.45(.018) TYP.
15
2.700.10 (.106.004)
10
0.450.05 (.018.002) (Mount height)
10
15
INDEX AREA
2.400.10 (.094.004)
2.01(.079) TYP 0.45(.018) TYP. 0.0750.025 (.003.001) (Stand off) "A" "C" "B"
0.90(.035) REF 1.90(.075) REF
1
6
6
1.35(.053) REF 2.28(.090) REF
1
Details of "A" part 0.05(.002) 0.14(.006) MIN. 0.250.06 (.010.002)
Details of "B" part C0.10(.004) 0.360.06 (.014.002)
Details of "C" part 0.360.06 (.014.002)
0.250.06 (.010.002)
0.280.06 (.011.002)
0.280.06 (.011.002)
C
2003 FUJITSU LIMITED C18058S-c-1-1
Dimensions in mm (inches) Note : The values in parentheses are reference values.
24
MB15F73UV
FUJITSU LIMITED
All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party's intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan.
F0312 (c) FUJITSU LIMITED Printed in Japan

▲Up To Search▲

Price & Availability of MB15F73UVPVB

	To Download MB15F73UVPVB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .