 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MMUN2211LT1 Series Preferred Devices Bias Resistor Transistor NPN Silicon Surface Mount Transistor with Monolithic Bias Resistor Network This new series of digital transistors is designed to replace a single device and its external resistor bias network. The BRT (Bias Resistor Transistor) contains a single transistor with a monolithic bias network consisting of two resistors; a series base resistor and a base-emitter resistor. The BRT eliminates these individual components by integrating them into a single device. The use of a BRT can reduce both system cost and board space. The device is housed in the SOT-23 package which is designed for low power surface mount applications. http://onsemi.com PIN 3 COLLECTOR (OUTPUT) R1 PIN 1 BASE (INPUT) R2 * Simplifies Circuit Design * Reduces Board Space and Component Count * The SOT-23 package can be soldered using wave or reflow. The * modified gull-winged leads absorb thermal stress during soldering eliminating the possibility of damage to the die. Available in 8 mm embossed tape and reel. Use the Device Number to order the 7 inch/3000 unit reel. Replace "T1" with "T3" in the Device Number to order the13 inch/10,000 unit reel. PIN 2 EMITTER (GROUND) MARKING DIAGRAM 3 1 2 SOT-23 CASE 318 STYLE 6 1 2 A8x = Device Code x = (See Table) 3 A8x MAXIMUM RATINGS (TA = 25C unless otherwise noted) Rating Collector-Base Voltage Collector-Emitter Voltage Collector Current Total Power Dissipation @ TA = 25C (Note 1) Derate above 25C Symbol VCBO VCEO IC PD Value 50 50 100 *200 1.6 Unit Vdc Vdc mAdc mW mW/C ORDERING INFORMATION Device MMUN2211LT1 MMUN2212LT1 MMUN2213LT1 Package SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 SOT-23 Shipping 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel DEVICE MARKING AND RESISTOR VALUES Device MMUN2211LT1 MMUN2212LT1 MMUN2213LT1 MMUN2214LT1 MMUN2215LT1 MMUN2216LT1 MMUN2230LT1 MMUN2231LT1 MMUN2232LT1 MMUN2233LT1 MMUN2234LT1 MMUN2238LT1 MMUN2241LT1 Marking A8A A8B A8C A8D A8E A8F A8G A8H A8J A8K A8L A8R A8U R1(K) 10 22 47 10 10 4.7 1.0 2.2 4.7 4.7 22 2.2 100 R2(K) 10 22 47 47 1.0 2.2 4.7 47 MMUN2214LT1 MMUN2215LT1 MMUN2216LT1 MMUN2230LT1 MMUN2231LT1 MMUN2232LT1 MMUN2233LT1 MMUN2234LT1 MMUN2238LT1 MMUN2241LT1 47 For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. Preferred devices are recommended choices for future use and best overall value. 1. Device mounted on a FR-4 glass epoxy printed circuit board using the minimum recommended footprint. (c) Semiconductor Components Industries, LLC, 2004 May, 2004 - Rev. 4 Publication Order Number: MMUN2211LT1/D MMUN2211LT1 Series THERMAL CHARACTERISTICS Rating Thermal Resistance - Junction-to-Ambient (surface mounted) Operating and Storage Temperature Range Maximum Temperature for Soldering Purposes, Time in Solder Bath Symbol RJA TJ, Tstg TL Value 625 -65 to +150 260 10 Unit C/W C C Sec ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit OFF CHARACTERISTICS Collector-Base Cutoff Current (VCB = 50 V, IE = 0) Collector-Emitter Cutoff Current (VCE = 50 V, IB = 0) Emitter-Base Cutoff Current (VEB = 6.0 V, IC = 0) MMUN2211LT1 MMUN2212LT1 MMUN2213LT1 MMUN2214LT1 MMUN2215LT1 MMUN2216LT1 MMUN2230LT1 MMUN2231LT1 MMUN2232LT1 MMUN2233LT1 MMUN2234LT1 MMUN2238LT1 MMUN2241LT1 ICBO ICEO IEBO - - - - - - - - - - - - - - - 50 50 - - - - - - - - - - - - - - - - - 100 500 0.5 0.2 0.1 0.2 0.9 1.9 4.3 2.3 1.5 0.18 0.13 4.0 0.1 - - nAdc nAdc mAdc Collector-Base Breakdown Voltage (IC = 10 mA, IE = 0) Collector-Emitter Breakdown Voltage (Note 2), (IC = 2.0 mA, IB = 0) V(BR)CBO V(BR)CEO Vdc Vdc ON CHARACTERISTICS (Note 2) DC Current Gain (VCE = 10 V, IC = 5.0 mA) MMUN2211LT1 MMUN2212LT1 MMUN2213LT1 MMUN2214LT1 MMUN2215LT1 MMUN2216LT1 MMUN2230LT1 MMUN2231LT1 MMUN2232LT1 MMUN2233LT1 MMUN2234LT1 MMUN2238LT1 MMUN2241LT1 hFE 35 60 80 80 160 160 3.0 8.0 15 80 80 160 160 - 60 100 140 140 350 350 5.0 15 30 200 150 350 350 - - - - - - - - - - - - - - 0.25 Vdc Collector-Emitter Saturation Voltage (IC = 10 mA, IB = 0.3 mA) (IC = 10 mA, IB = 5 mA) MMUN2230LT1/MMUN2231LT1 (IC = 10 mA, IB = 1 mA) MMUN2215LT1/MMUN2216LT1 MMUN2232LT1/MMUN2233LT1/MMUN2234LT1/ MMUN2238LT1 2. Pulse Test: Pulse Width < 300 ms, Duty Cycle < 2.0%. VCE(sat) http://onsemi.com 2 MMUN2211LT1 Series ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) (Continued) Characteristic Symbol Min Typ Max Unit ON CHARACTERISTICS (Note 3) Output Voltage (on) (VCC = 5.0 V, VB = 2.5 V, RL = 1.0 k ) VOL MMUN2211LT1 MMUN2212LT1 MMUN2214LT1 MMUN2215LT1 MMUN2216LT1 MMUN2230LT1 MMUN2231LT1 MMUN2232LT1 MMUN2233LT1 MMUN2234LT1 MMUN2238LT1 MMUN2213LT1 MMUN2241LT1 VOH - - - - - - - - - - - - - 4.9 - - - - - - - - - - - - - - 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 - Vdc Vdc (VCC = 5.0 V, VB = 3.5 V, RL = 1.0 k ) (VCC = 5.0 V, VB = 5.0 V, RL = 1.0 k ) Output Voltage (off) (VCC = 5.0 V, VB = 0.5 V, RL = 1.0 k ) (VCC = 5.0 V, VB = 0.050 V, RL = 1.0 k ) MMUN2230LT1 MMUN2215LT1 (VCC = 5.0 V, VB = 0.25 V, RL = 1.0 k ) MMUN2216LT1 MMUN2233LT1 MMUN2238LT1 Input Resistor MMUN2211LT1 MMUN2212LT1 MMUN2213LT1 MMUN2214LT1 MMUN2215LT1 MMUN2216LT1 MMUN2230LT1 MMUN2231LT1 MMUN2232LT1 MMUN2233LT1 MMUN2234LT1 MMUN2238LT1 MMUN2241LT1 MMUN2211LT1/MMUN2212LT1/MMUN2213LT1 MMUN2214LT1 MMUN2215LT1/MMUN2216LT1/MMUN2238LT1 MMUN2241LT1 MMUN2230LT1/MMUN2231LT1/MMUN2232LT1 MMUN2233LT1 MMUN2234LT1 R1 7.0 15.4 32.9 7.0 7.0 3.3 0.7 1.5 3.3 3.3 15.4 1.54 70 0.8 0.17 - - 0.8 0.055 0.38 10 22 47 10 10 4.7 1.0 2.2 4.7 4.7 22 2.2 100 1.0 0.21 - - 1.0 0.1 0.47 13 28.6 61.1 13 13 6.1 1.3 2.9 6.1 6.1 28.6 2.88 130 1.2 0.25 - - 1.2 0.185 0.56 k Resistor Ratio R1/R2 3. Pulse Test: Pulse Width < 300 ms, Duty Cycle < 2.0%. http://onsemi.com 3 MMUN2211LT1 Series TYPICAL ELECTRICAL CHARACTERISTICS MMUN2211LT1 VCE(sat), MAXIMUM COLLECTOR VOLTAGE (VOLTS) PD, POWER DISSIPATION (MILLIWATTS) 250 1 IC/IB = 10 TA = -25C 25C 75C 200 0.1 150 100 RJA= 625C/W 0.01 50 0 -50 0 50 100 150 0.001 0 20 40 60 80 TA, AMBIENT TEMPERATURE (5C) IC, COLLECTOR CURRENT (mA) Figure 1. Derating Curve hFE, DC CURRENT GAIN (NORMALIZED) 1000 VCE = 10 V TA = 75C 25C -25C 100 Cob, CAPACITANCE (pF) 3 4 Figure 2. VCE(sat) vs. IC f = 1 MHz lE = 0 A TA = 25C 2 1 10 1 10 IC, COLLECTOR CURRENT (mA) 100 0 0 10 20 30 40 50 VR, REVERSE BIAS VOLTAGE (VOLTS) Figure 3. DC Current Gain 100 IC, COLLECTOR CURRENT (mA) 75C Vin, INPUT VOLTAGE (VOLTS) 10 TA = -25C 10 Figure 4. Output Capcitance 25C VO = 0.2 V TA = -25C 25C 75C 1 1 0.1 0.01 VO = 5 V 0 1 2 3 4 5 6 7 8 9 10 0.001 0.1 0 Vin, INPUT VOLTAGE (VOLTS) 10 20 30 40 IC, COLLECTOR CURRENT (mA) 50 Figure 5. Output Current vs. Input Voltage Figure 6. Input Voltage vs. Output Current http://onsemi.com 4 MMUN2211LT1 Series TYPICAL ELECTRICAL CHARACTERISTICS MMUN2212LT1 VCE(sat), MAXIMUM COLLECTOR VOLTAGE (VOLTS) hFE, DC CURRENT GAIN (NORMALIZED) 1 IC/IB = 10 TA = -25C 25C 75C 1000 VCE = 10 V TA = 75C 0.1 25C 100 -25C 0.01 - 0.001 0 20 60 40 IC, COLLECTOR CURRENT (mA) 80 10 1 10 IC, COLLECTOR CURRENT (mA) 100 Figure 7. VCE(sat) vs. IC 4 f = 1 MHz lE = 0 A TA = 25C IC, COLLECTOR CURRENT (mA) 100 Figure 8. DC Current Gain 75C 25C TA = -25C Cob, CAPACITANCE (pF) 3 10 1 2 0.1 1 0.01 VO = 5 V 0 0 10 20 30 40 50 0.001 0 2 4 6 8 10 VR, REVERSE BIAS VOLTAGE (VOLTS) Vin, INPUT VOLTAGE (VOLTS) Figure 9. Output Capacitance 100 Vin, INPUT VOLTAGE (VOLTS) VO = 0.2 V Figure 10. Output Current vs. Input Voltage TA = -25C 10 75C 25C 1 0.1 0 10 20 30 40 50 IC, COLLECTOR CURRENT (mA) Figure 11. Input Voltage vs. Output Current http://onsemi.com 5 MMUN2211LT1 Series TYPICAL ELECTRICAL CHARACTERISTICS MMUN2213LT1 VCE(sat), MAXIMUM COLLECTOR VOLTAGE (VOLTS) 10 IC/IB = 10 TA = -25C 25C 1 75C hFE, DC CURRENT GAIN (NORMALIZED) 1000 VCE = 10 V TA = 75C 25C -25C 100 0.1 0.01 0 20 40 60 80 IC, COLLECTOR CURRENT (mA) 10 1 10 IC, COLLECTOR CURRENT (mA) 100 Figure 12. VCE(sat) vs. IC 1 IC, COLLECTOR CURRENT (mA) f = 1 MHz lE = 0 A TA = 25C 100 Figure 13. DC Current Gain 75C 10 25C TA = -25C Cob, CAPACITANCE (pF) 0.8 0.6 1 0.4 0.1 0.2 0.01 VO = 5 V 0 2 4 6 8 Vin, INPUT VOLTAGE (VOLTS) 10 0 0 10 20 30 40 50 0.001 VR, REVERSE BIAS VOLTAGE (VOLTS) Figure 14. Output Capacitance 100 VO = 0.2 V Vin, INPUT VOLTAGE (VOLTS) Figure 15. Output Current vs. Input Voltage TA = -25C 25C 10 75C 1 0.1 0 10 20 30 40 IC, COLLECTOR CURRENT (mA) 50 Figure 16. Input Voltage vs. Output Current http://onsemi.com 6 MMUN2211LT1 Series TYPICAL ELECTRICAL CHARACTERISTICS MMUN2214LT1 VCE(sat), MAXIMUM COLLECTOR VOLTAGE (VOLTS) hFE, DC CURRENT GAIN (NORMALIZED) 1 IC/IB = 10 TA = -25C 25C 0.1 75C 300 VCE = 10 250 25C 200 -25C 150 100 50 0 TA = 75C 0.01 0.001 0 20 40 60 IC, COLLECTOR CURRENT (mA) 80 1 2 4 6 8 10 15 20 40 50 60 70 80 90 100 IC, COLLECTOR CURRENT (mA) Figure 17. VCE(sat) vs. IC 4 3.5 Cob, CAPACITANCE (pF) 3 2.5 2 1.5 1 0.5 0 0 2 4 6 8 10 15 20 25 30 35 40 45 50 VR, REVERSE BIAS VOLTAGE (VOLTS) f = 1 MHz lE = 0 A TA = 25C IC, COLLECTOR CURRENT (mA) 100 Figure 18. DC Current Gain 75C 25C TA = -25C 10 VO = 5 V 1 0 2 4 6 8 Vin, INPUT VOLTAGE (VOLTS) 10 Figure 19. Output Capacitance 10 VO = 0.2 V Vin, INPUT VOLTAGE (VOLTS) Figure 20. Output Current vs. Input Voltage TA = -25C 25C 75C 1 0.1 0 10 20 30 40 IC, COLLECTOR CURRENT (mA) 50 Figure 21. Input Voltage vs. Output Current http://onsemi.com 7 MMUN2211LT1 Series TYPICAL ELECTRICAL CHARACTERISTICS MMUN2232LT1 1 VCE(sat), MAXIMUM COLLECTOR VOLTAGE (VOLTS) IC/IB =10 hFE, DC CURRENT GAIN TA = 75C 100 -25C 25C 1000 VCE = 10 V 0.1 TA = 75C 25C -25C 0.01 10 0.001 4 8 12 16 20 24 28 IC, COLLECTOR CURRENT (mA) 1 0 25 50 75 100 125 IC, COLLECTOR CURRENT (mA) Figure 22. VCE(sat) vs. IC 6 IC, COLLECTOR CURRENT (mA) 5 4 3 2 1 0 0 10 20 30 40 50 60 VR, REVERSE BIAS VOLTAGE (VOLTS) f = 1 MHz IE = 0 A TA = 25C 100 75C 10 Figure 23. DC Current Gain VO = 5 V 25C Cob, CAPACITANCE (pF) 1 TA = -25C 0.1 0.01 0 2 4 6 8 Vin, INPUT VOLTAGE (VOLTS) Figure 24. Output Capacitance 10 VO = 0.2 V Vin, INPUT VOLTAGE (VOLTS) TA = -25C 75C 1 25C Figure 25. Output Current vs. Input Voltage 0.1 0 10 20 IC, COLLECTOR CURRENT (mA) 30 Figure 26. Output Voltage vs. Input Current http://onsemi.com 8 MMUN2211LT1 Series TYPICAL ELECTRICAL CHARACTERISTICS MMUN2233LT1 1 VCE(sat), MAXIMUM COLLECTOR VOLTAGE (VOLTS) IC/IB = 10 hFE, DC CURRENT GAIN 75C 25C TA = -25C 1000 0.1 75C 25C TA = -25C 100 0.01 10 VCE = 10 V 1 2 7 12 17 22 27 32 1 10 IC, COLLECTOR CURRENT (mA) 100 IC, COLLECTOR CURRENT (mA) 0.001 Figure 27. VCE(sat) vs. IC 4 3.5 Cob, CAPACITANCE (pF) 3 2.5 2 1.5 1 0.5 0 0 10 20 30 40 50 60 VR, REVERSE BIAS VOLTAGE (VOLTS) f = 1 MHz IE = 0 A TA = 25C IC, COLLECTOR CURRENT (mA) 100 75C Figure 28. DC Current Gain TA = -25C 10 1 0.1 25C 0 2 4 6 VO = 5 V 8 0.01 Vin, INPUT VOLTAGE (VOLTS) Figure 29. Output Capacitance 10 VO = 0.2 V Vin, INPUT VOLTAGE (VOLTS) Figure 30. Output Current vs. Input Voltage TA = -25C 25C 1 75C 0.1 0 12 18 6 24 IC, COLLECTOR CURRENT (mA) 30 Figure 31. Input Voltage vs. Output Current http://onsemi.com 9 MMUN2211LT1 Series TYPICAL APPLICATIONS FOR NPN BRTs +12 V ISOLATED LOAD FROM P OR OTHER LOGIC Figure 32. Level Shifter: Connects 12 or 24 Volt Circuits to Logic +12 V VCC OUT IN LOAD Figure 33. Open Collector Inverter: Inverts the Input Signal Figure 34. Inexpensive, Unregulated Current Source http://onsemi.com 10 MMUN2211LT1 Series PACKAGE DIMENSIONS SOT-23 TO-236AB CASE 318-08 ISSUE AI A L 3 1 2 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. 318-03 AND -07 OBSOLETE, NEW STANDARD 318-08. INCHES MIN MAX 0.1102 0.1197 0.0472 0.0551 0.0350 0.0440 0.0150 0.0200 0.0701 0.0807 0.0005 0.0040 0.0034 0.0070 0.0140 0.0285 0.0350 0.0401 0.0830 0.1039 0.0177 0.0236 MILLIMETERS MIN MAX 2.80 3.04 1.20 1.40 0.89 1.11 0.37 0.50 1.78 2.04 0.013 0.100 0.085 0.177 0.35 0.69 0.89 1.02 2.10 2.64 0.45 0.60 BS V G C D H K J DIM A B C D G H J K L S V STYLE 6: PIN 1. BASE 2. EMITTER 3. COLLECTOR SOLDERING FOOTPRINT* 0.95 0.037 0.95 0.037 2.0 0.079 0.9 0.035 0.8 0.031 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 11 MMUN2211LT1 Series ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. http://onsemi.com 12 MMUN2211LT1/D |
Price & Availability of MMUN2241LT1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |