View NSVS680_1289844.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NSVS680 Jul-03
JRC SAW FILTER
NSVS680
Application
European keyless
Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Input and Output Impedance Nominal Center Frequency (f0) Insertion Loss 446~448MHz Response Variation 446~448MHz Input and Output VSWR 446~448MHz Out of Band Rejection 425.3MHz
(Relative to Through Level)
Spec. 50 447 MHz 3.0dB max. 1.5dB max. 2.5 max. 45dB min.
(Operating Temperature Range: -20~+70C)
Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature
Rating +20dBm 7.5V -20~+70C -30~+80C
Mechanical Specifications: (Fig.2) Package is designed as small as 3.5x3.5x1.0[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling.
Communications and Device Group Communications Equipment Marketing Department
10-1, Nishi-Shinjuku 6-chome, Shinjuku-ku, Tokyo, 160-8328 Japan Tel. +81 3-3348-3845 Fax. +81 3-3348-3935 http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese) http://www.jrc.co.jp/eng/product/comm/device/saw/saw_top_e.html (English)
NSVS680 Jul-03
IN 50
1
8
7
OUT 50
2 SAW 6 3 4 5
(a) (1)
Fig.1 Measuring circuit
3.50.2 (b)
3 .5 0 .2
J17
HK
(3) (0.95)
(2)
4
(0.8) [5x]
(0 .6 )
5
(0.6)
[8 x ]
3
Marking (1) Manufacture's Mark (2) Lot Number (a) Year (b) Month *Oct.--- X Nov.--- Y Dec.--- Z (3) Part number Mark Pin no. 1 2 3 4 5 6 7 8 Connection GND IN/OUT GND GND GND OUT/IN GND GND
1 .0 0 .2 (2 .5 4 ) (1 .2 7 )
2
6
(1.0) [2 x ]
1 8
7
Fig.2 Package dimensions (in mm)
4.3 0.6 1.2 [6x]
4.3
1.27
1.27
Via -Hole(0.3)
Fig.3 Desirable land area (in mm)
0.6 [6x]
NSVS680 Jul-03
Notice
1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -20C or more than +70C, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350C max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products.

▲Up To Search▲

Price & Availability of NSVS680

	To Download NSVS680 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .