View AL-HD1G6B433T_4143677.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Full Color Chip LED Lamps Part Number: AL-HD1G6B433T Package outlines & Re-flow Profile
Reflow Temp/Time
1
3
2
4
Soldering iron Basic spec is 5sec when 260. If temperature is higher, time should be shorter (+10 -1sec ).Power dissipation of iron should be smaller than 15W, and temperatures should be controllable .Surface temperature of the device should be under 230 .
ITEM
Resin (mold) Lens color Printed circuit board
R1 G3 B4 2
MATERIALS
Epoxy Water Clear BT GaAlAs/GaAs InGaN InGaN Super Red
Dice
For Reflow Soldering
Emitted color
Green Super Blue
NOTES:
1. All dimensions are in millimeters (inches). 2. Tolerances are 0.1mm (0.004inch) unless otherwise noted. 3. Polarity referring onto the cathode mark is reversed on the red.
2007/6/13
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: AL-HD1G6B433T ELECTRO-OPTICAL CHARACTERISTICS
Parameter Forward voltage Luminous intensity Emitted Color
Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue
(TA=25)
Unit
V
Value Test Symbol Condition MIN. TYP. MAX.
IF=20mA VF - - - 12.3 94 28 - - - 638 520 465 - - - 1.8 3.4 3.5 25 180 50 660 525 470 - - - 20 30 30 100 60 120 120 2.6 3.8 4.0 - - - - - - 648 530 475 - - -
IF=20mA
IV
mcd
p IF=20mA d
Wavelength
nm
Spectral Line Half-Width
Peak pulsing current (1/10 duty f=1kHz)
IF=20mA
nm
IF=20mA
IFP
mA
Power Dissipation
IF=20mA
PD
mW
Absolute maximum ratings
Parameter Symbol 21/2 IF VR IR Top Tstg Value 120 30 5 100
(TA=25)
Unit
Viewing angle at 50% Iv
Forward current Reverse voltage Reverse current Operating temperature range Storage temperature range
Deg
mA V A
2007/6/13
-25 ~+80 -30 ~+85
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: AL-HD1G6B433T Test items and results of reliability
Refer to reliability test standard specification for in this line.
2007/6/13
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: AL-HD1G6B433T Typical Electro-Optical Characteristics Curves
2007/6/13
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: AL-HD1G6B433T
Precautions For Use
1. Over-current proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
2007/6/13

▲Up To Search▲

Price & Availability of AL-HD1G6B433T

	To Download AL-HD1G6B433T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .