View LQ038Q7DB03R_4149187.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRODUCT SPECIFICATIONS Mobile Liquid Crystal Displays Group
LQ038Q7DB03R
TFT-LCD Module
Spec. Issue Date: May 20, 2005 No: LCP-05007
RECORDS OF REVISION
NO. LCP-5007 PAGE SUMMARY NOTE 1 st Issue
2005.05.18
LCP-05007-1
NOTICE
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP Express written permission is also required before any use of this publication may be made by a third party.
The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice.
Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices.
The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: * Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) * Traffic signals * Gas leakage sensor breakers * Alarm equipment * Various safety devices etc. SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: * Military and space applications * Medical equipment for life support * Nuclear power control equipment
Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP.
Contact and consult with a SHARP representative if there are any questions about the contents of this publication.
(1) Application This literature applies to LQ038Q7DB03R. (2) Overview This module is a color reflective and active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor), named AD-TFT(Advanced TFT). It is composed of a color TFT-LCD panel, driver ICs, an FPC, a back light, and a back sealed casing. It isn't composed control circuit. Graphics and texts can be displayed on a 240 direction. 3 Mechanical specifications Table 1 Parameter Screen size (Diagonal) Display active area Touch panel active area Pixel format Pixel pitch Pixel configuration Unit outline dimension Mass Surface hardness (Touch panel) Note 3-1 Excluding FPC. For detailed measurements and tolerances, please refer to Fig. 1. (4)Pixel configuration (1,1) (240,1) 57.6 57.9 Specifications 9.54 [3.78 ] Diagonal H H 76.8 V 77.8 V Units cm mm mm pixels mm mm Note3-1 Remarks 3 320 dots panel with 262,144 colors by supplying. Optimum view angle is 6 o'clock. An inverted display mode is selective in the vertical or the horizontal
240(H) 320(V) (1 pixel = R+G+B dots) 0.24 H 0.24 V 3.4(D) R,G,B vertical stripe 69.0(W) 88.6(H) 42 3H
RGB
Display area
(1,320)
(240,320)
FPC
(5)Input/Output terminal 5-1)TFT-LCD panel driving section Table2 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Symbol DGND VSHA NC VSHD VDD NC VEE NC VCOM VCOM VSS VCC NC R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 V0 V1 V2 V3 V4 NC I I I I I I I I I I I I I I I I I I I I I I I RED data signal(LSB) RED data signal RED data signal RED data signal RED data signal RED data signal(MSB) GREEN data signal(LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal(MSB) BLUE data signal(LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal(MSB) Standard voltage to generate gray scale voltage Standard voltage to generate gray scale voltage Standard voltage to generate gray scale voltage Standard voltage to generate gray scale voltage Standard voltage to generate gray scale voltage I I Common electrode driving signal Common electrode driving signal Power supply of gate driver(logic low) Power supply of gate driver(logic high) Note5-1 Note5-1 Power supply of gate driver(low level) Power supply of digital Power supply of gate driver(high level) I/O Ground(digital) Power supply(analog) Description Remarks
Pin No. 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
Symbol NC NC AGND NC NC NC DCLK SPL LP CLS SPS PS NC MOD MOD U/L LBR DGND SPR LED+ LED+ LED LED AGND
I/O
Description
Remarks
Ground(Analog)
I I/O I I I I I I I I I/O
Data sampling clock signal Sampling start signal Data latch signal of source driver Clock signal of gate driver Start signal of gate driver Power save signal Control signal of gate driver Control signal of gate driver Selection for vertical scanning direction Selection for horizontal scanning direction Ground(digital) Sampling start signal Power supply for LED (High voltage) Power supply for LED (High voltage) Power supply for LED (Low voltage) Power supply for LED (Low voltage) Ground(Analog) Note5-2 Note5-2 Note5-3 Note5-4
Note5-1 Note5-2 Note5-3 U/L High
See section(7-1)-(A) and Note 7-8 See section(7-1)-(A) " Cautions when you turn on or off the power supply". Selection for vertical scanning direction Scanning direction (Pixel configuration) Normal scanning ( X , 1 ) ( X , 320 )
Low
Inverted scanning ( X , 1) ( X , 320)
Note5-4 LBR High Low
Selection for horizontal scanning direction SPL Input Output SPR Output Input Scanning direction (Pixel configuration) Normal scanning (1,Y) Inverted scanning (1,Y) (240,Y) (240,Y)
(6)Absolute Maximum Ratings Table 4 Parameter Power supply(source/Analog) Power supply(source/Digital) Power supply (gate) Power supply (gate) Power supply (gate) Power supply (gate) Input voltage (Analog) Input voltage (Digital) Operating temperature (panel surface Storage temperature [Terminal ] V0,V1,V2,V3,V4 [Terminal ] MOD,U/L,SPS,CLS,SPL,R0 R5,G0 G5,B0 B5,LP,DCLK,LBR,SPR,PS Note6-1 Humidity: 95%RH Max.(at Ta 40 ). Maximum wet-bulb temperature is less than 39 (at Ta > 40 ). Condensation of dew must be avoided. (7)Electrical characteristics 7-1)Recommended operating conditions A) TFT-LCD panel driving section Table 6 Parameter Supply voltage for source driver (Analog) Supply voltage for source driver (Digital) Standard input voltage High voltage Logic high voltage Supply voltage for gate driver Logic low voltage Low voltage (AC) Low voltage (DC) Input voltage for Source driver (Low) Input voltage for Source driver (High) Input current for Source driver (Low) Input current for Source driver (High) Input voltage for Gate driver (Low) Input voltage for Gate driver (High) Input current for Gate driver (Low) Input current for Gate driver (High) Common electrode AC component driving signal DC component Symbol VSHA VSHD V0 V4 VDD VCC VSS VEEAC VEEDC VILS VIHS IILS IIHS1 IIHS2 VILG VIHG IILG IIHG VCOMAC VCOMDC +0.1 2.5 +1.1 GND 0.8VSHD 9.5 GND 0.8VSHD Min. +4.5 +3.0 0 +14.5
0.1
Symbol VSHA VSHD VDD VEE VCC VDD VSS VSS VEE (VSS) VIA VID opp stg
Condition Ta=25 Ta=25 Ta=25 Ta=25 Ta=25 Ta=25 Ta=25 Ta=25
Ratings 0.3 0.3 0.3 0.3 0.3 0.3 +7.0 +7.0 +35.0 +35.0 +7.0 +35.0
Unit V V V V V V V V
Remark
0.3 VSHA+0.3 0.3 VSHD+0.3 0 50
[Terminal ] [Terminal ] Note6-1 Note6-1
25 70
GND=0V Typ. +5.0 +3.3 Max. +5.5 +3.6 VSHA +15.0 +15.5
0.1
Unit V V V V V V Vp-p
Remarks
Note 7-1 Note 7-2
VSS+VSHD VSS+VSHD VSS+VSHD
14.3
15.0 VCOMAC 9.0
15.7 8.5 0.2VSHD VSHD 30 30 1200 0.2VSHD VSHD 4 4 2.6 +2.1
Note 7-3 Note 7-3 Note 7-4 Note 7-4 Note 7-4 Note 7-5 Note 7-6 Note 7-7 Note 7-7 Note 7-7 Note 7-7 Note 7-8 Note 7-8
V V V A A A V V A A Vp-p V
Cautions when you turn on or off the power supply Turn on or off the power supply with simultaneously or the following sequence. Turn on Turn off VSHD VSHA VDD VEE VSS VCC VCC VSS VEE VSHA VDD VSHD
The input signal of "MOD" Terminals(Pin No.51 and No.52) must be low voltage when turning on the power supply, and it is held until more than double vertical periods after VCC is turned on completely. After then, it must be held high voltage until turning off the power supply.(Connect Pin No.51 and No.52 terminals to the same signal.) Note 7-1 These are standard input voltages for gray scale. When VCOM is alternated polarity, these voltage should be alternated polarity. V0(black) is different polarity alternating signal of VCOM. V4(white) is the same polarity alternating signal of VCOM. Center voltage of each standard input voltage shift positive way for LCD characteristics (V0 V1 V2 V3 V4). This sift amount is adjusted so as to no flicker of each standard input voltage after DC bias voltage of VCOM and V0 is adjusted. Note 7-2 It must be kept that 3.0V (VCC-VSS) 3.6V. G5 and B0 B5 terminals are applied. Note 7-3 The same phase and amplitude with VCOM. VEEDC is center of VEE. Note 7-4 DCLK,SPL,SPR,LBR,LP,PS,R0 R5,G0 Note 7-6 PS terminal is applied. Note 7-7 MOD,CLS,SPS and U/L terminals are applied. Note 7-8 VCOMAC should be alternated on VCOMDC every 1 horizontal period and 1 vertical period. VCOMDC bias is adjusted so as to minimize flicker or maximum contrast every each module . Note 7-5 DCLK,SPL,SPR,LBR,LP,R0 R5,G0 G5 and B0 B5 terminals are applied.
B)
Back light driving section Ta=25 Symbol VL IL WL MIN TYP 32.4 15 486 MAX 36.0 20 720 Units V A mW Note 7-9 Remarks terminal Parameter
Table 7 LED voltage LED current Power consumption
Note 7-9 Calculated reference value(IL VL)
7-2) Timing Characteristics of input signals Table 8 AC Characteristics (1) Parameter Clock frequency of source driver Rising time of clock Falling time of clock Pulse width (High level) Pulse width (Low level) Frequency of start pulse Source driver Setup time of start pulse Hold time of start pulse Pulse width of start pulse Setup time of latch pulse Hold time of latch pulse Pulse width of latch pulse Setup time of PS Hold time of PS Set up time of data Hold time of data Clock frequency Pulse width of clock(Low) Pulse width of clock(High) Rising time of clock Falling time of clock Gate driver Setup time of clock Hold time of clock Frequency of start pulse Setup time of start pulse Hold time of start pulse Rising time of start pulse Falling time of start pulse Vcom Setup time of Vcom Hold time of Vcom Note 7-10 SPL="Hi". Symbol fCK Tcr Tcf Tcwh Tcwl fsp Tsusp Thsp Twsp Tsulp Thlp Twlp Tsups Thps Tsud Thd fcls Twlcls Twhcls Trcls Tfcls Tsucls Thcls fsps Tsu Th Trsp Tfsp Tsuvcom Thvcom 3 1 3 0 50 100 300 100 100 86 20 20 60 0 0 15 10 16.5 5 30 100 100 28 (1/fclk)-30 40 40 16.5 15 10 1.5/fCK 28 Min. 4.5 Typ. (VSHA=+5V, VSHD=+3.3V, Ta=25 ) Max. 6.8 20 20 Unit MHz ns ns ns ns kHz ns ns ns ns ns ns s s ns ns kHz s s ns ns s s Hz ns ns ns ns s s Vcom SPS CLS PS R0 R5,G0 G5 ,B0 B5 LP Note 7-10 SPL,SPR DCLK Remark
There must be only one up-edge of DCLK (includes Tsusp and Thsp time) in the period of
Fig.(a) Horizontal timing chart
Fig.(b) Vertical timing chart
7-3)Power consumption Measurement condition : SPS=60Hz,CLS=15.73kHz,SPL=15.73kHz,DCLK=6.3MHz The term of PS="Lo" in one horizontal period Ta=25 Table 9 Parameter Source current Gate current Analog Digital High Low logic High logic Low Power consumption Sym Conditions MIN TYP 5.0 1.8 0.05 0.03 0.08 0.18 33 25 MAX 10 3.6 0.10 0.06 0.16 0.36 66 50 ISHA VSHA=+5.0V ISHD VSHD=+3.3V IDD IEE ICC ISS Pd1 Pd2 VDD=+15.0V VEE= 9.0 2.5V VCC= 11.7V VSS= 15.0V Note 7-14 when normal scan mode Unit mA mA mA mA mA mA mW mW Remarks Note 7-11 Note 7-11 Note 7-12 Note 7-12 Note 7-12 Note 7-12 Note 7-11 Note 7-13 37 sec(234DCLK)
Note 7-11 Vertical stripe pattern alternating 21 gray scale (GS21) with 42 gray scale (GS42) every 1 dot. Note 7-12 64-Gray-bar vertical pattern (GS0 Note 7-13 all black pattern (GS0) Note 7-14 Voltage conditions VSHA=+5.0V , VSHD=+3.3V , VDD=+15.0V VEE= 9.0 2.5V , VCC= 11.7V , VSS= 15.0V GS63 for horizontal way)
.Input Signals, Basic Display Color and Gray Scale of Each Colornn Table 10 Colors & Gray scale Gray Scale Black Blue Green Cyan Red Magenta Yellow White Black Gray Scale of red Gray Scale of green Gray Scale of bleu GS0 GS1 Darker GS2 Basic color 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 R0 R1 R2 R3 Data signal R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
Brighter
GS61 GS62
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Red Black
GS63 GS0 GS1
Darker
GS2
Brighter
GS61 GS62
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Green Black
GS63 GS0 GS1
Darker
GS2
Brighter
GS61 GS62
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
1 0 1
0 1 1
1 1 1
1 1 1
1 1 1
1 1 1
Bleu
GS63
0 :Low level voltage
1 :High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen.
(9)Optical characteristics 9-1)Not driving the Back light condition Table 12 Parameter Viewing angle Range Symbol 21,22 11 12 Contrast ratio Response Time Rise Fall CRmax r d White - x White - y Red - x Color chromaticity Red - y Green - x Green - y Blue - x Blue - y Reflection ratio R =0 =0 =0 =0 0.25 0.28 0.34 0.25 0.25 0.34 0.15 0.21 7 CR2 Condition Min 40 40 40 4 Typ 50 50 50 8 30 50 0.30 0.33 0.39 0.31 0.30 0.39 0.20 0.26 11 60 100 0.35 0.38 0.44 0.35 0.35 0.44 0.25 0.31 % [Note 9-5,6] ms ms [Note 9-5] Max Unit degree degree degree [Note 9-2,5] [Note 9-4] Remarks [Note 9-1,2] Ta=25C
* The measuring method of the optical characteristics is shown by the following figure. * A measurement device is Otsuka luminance meter LCD5200.(With the diffusion reflection unit.) Normal line Photodetector (with luminosity correction system) Chemical coated surface (Optical diffusion treatment)
A diffusion beam
A diffusion beam
A beam (through an optical fiber) Touch panel Module
Center of display
Measuring method (a) for optical characteristics
9-2)Driving the Back light condition Table 13 Parameter Viewing angle range Symbol 21,22 11 12 Contrast ratio Response time Rise Fall Crmax r d White - x White - y Red - x Color chromaticity Red - y Green - x Green - y Blue - x Blue - y Brightness Lamp life time Uniformity Y LL = 0 IL=20mA 75 = 0 0.25 0.27 0.43 0.27 0.26 0.38 0.11 0.15 75 = 0 CR2 Condition Min 30 30 30 40 Typ 40 40 40 75 30 50 0.30 0.32 0.48 0.32 0.31 0.43 0.16 0.20 90 10000 85 60 100 0.35 0.37 0.53 0.37 0.36 0.48 0.21 0.25 cd/m2 hour % IL=20mA [Note 9-7] [Note 9-8] ms ms Max Ta=25C Unit degree degree degree [Note 9-2] [Note 9-4] Remarks [Note 9-1,2]
* The measuring method of the optical characteristics is shown by the following figure. * A measurement device is TOPCON luminance meter BM-5(A).(Viewing cone 1)
Photodetector(including luminosity facter)
Touch panel LCD module
Center
Measuring method (c) for optical characteristics
[Note 9-1] Viewing angle range is defined as follows.
Normal line
o'clock direction
Definition for viewing angle [Note 9-2] Definition of contrast ratio: The contrast ratio is defined as follows: Photodetecter output with all pixels white(GS63) Contrast ratio(CR)= Photodetecter output with all pixels black(GS0) VCOMAC=5.0Vp-p,V0=4.0Vp-p,V4=-4.0Vp-p [Note 9-3] These values are under the condition of measuring method(b) with a point light source (lighting angle = 30 ). [Note 9-4] Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white".
White
Black
White
100% 90% Photodetecter output (arbitrary unit) 10% 0% r
Time
d
[Note 9-5] A measurement device is Minolta CM-2002. [Note 9-6] Definition of reflection ratio Reflection ratio =
Light detected level of the reflection by the LCD module Light detected level of the reflection by the standard white board
[Note 9-7] The White-LED life time is defined as a time when brightness not to become under 50% of the original value.(at Ta=25 ) [Note 9-8] Definition of Uniformity Uniformity =
Minimum brightness Maximum brightness
(
)
The brightness should be measured on 9spots of the display as follows.
(10)Display quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standards for TFT-LCD.. (11)Mechanical characteristics 11-1) External appearance See Fig. 1 11-2) FPC (for LCD panel) characteristics (1) Specific connector Hirose FH23-61S-0.3SHAW(05) (2) Bending endurance of the bending slits portion No line of the FPC is broken for the bending test (Bending radius=0.6mm and angle=90) in 30 cycles.
(12)Handling Precautions 12-1) Insertion and taking out of FPCs Be sure insert and take out of the FPC into the connector of the set after turning off the power supply on the set side. 12-2) Handling of FPCs The FPC for LCD panel shall be bent only slit portion. The bending slit shall be bent uniformly on the whole slit portion with bending radius larger than 0.6mm ,and only inner side (back side of the module). Don't bend it outer side (display surface side). Don't give the FPCs too large force, for example, hanging the module with holding FPC. 12-3) Installation of the module On mounting the module, be sure to fix the module on the same plane. Taking care not to warp or twist the module. 12-4)Precaution when mounting (1) If water droplets and oil attaches to it for a long time, discoloration and staining occurs. Wipe them off immediately. (2) Glass is used for the TFT-LCD panel and touch panel. If it is dropped or bumped against a hard object, it may be broken. Handle it with sufficient care. (3)As the CMOS IC is used in this module, pay attention to static electricity when handling it. Take a measure for grounding on the human body. 12-5)Others (1) The liquid-crystal is deteriorated by ultraviolet rays. Do not leave it in direct sunlight and strong ultraviolet rays for many hours. (2) If it is kept at a temperature below the rated storage temperature, it becomes coagulated and the panel may be broken. Also, if it is kept at a temperature above the rated storage temperature, it becomes isotropic liquid and does not return to its original state. Therefore, it is desirable to keep it at room temperature as much as possible. (3) If the LCD breaks, don't put internal liquid crystal into the mouth. When the liquid crystal sticks to the hands, feet and clothes, wash it out immediately. (4) Wipe off water drop or finger grease immediately. Long contact with water may cause discoloration or spots. (5) Observe general precautions for all electronic components. (6) VCOM must be adjusted on condition of your final product. No adjustment causes the deterioration for display quality.
(13)Reliability Test Conditions for TFT-LCD Module Table 14 No. 1 2 3 4 5 6 7 Test items High test Low temperature storage test Ta= 20 High temperature and high Tp=+40 humidity operating test test Low temperature operating Tp=0 test Electro static discharge test Shock tset 200V 200pF(0 ) 1 time for each terminals 980 m/s2, 6 ms X, Y, Z 3 times for each direction (JIS C0041, A-7 Condition C) 8 Vibration test Frequency range: 10Hz 55Hz Stroke: 1.5 mm Sweep: 10Hz 55Hz X,Y,Z 2 hours for each direction (total 6 hours) (JIS C0040,A-10 Condition A) 9 Heat shock test Ta=-25 (1h) +70 (1h) / 5 cycles 240h High temperature operating Tp=+50 , 95%RH 240h 240h 240h temperature storage Ta=+60 Test conditions 240h
(But no condensation of dew)
Note Ta = Ambient temperature, Tp = Panel temperature Check items In the standard condition, there shall be no practical problems that may affect the display function. (14) Others 14-1)Indication of lot number The lot number is shown on a label. Attached location is shown in Fig.1 (Outline Dimensions). Indicated contents of the label LQ038Q7DB03R model No. lot No. 14-2) Used Regulation of Chemical Substances Breaking Ozone Stratum Substances with the object of regulating : CFCS, Carbon tetrachloride, Halon 1,1,1-Trichloro ethane (Methyl chloroform) (a) This LCD module, Constructed part and Parts don't contain the above substances. (b) This LCD module, Constructed part and Parts don't contain the above substances in processes of manufacture. 14-3) If some problems arise about mentioned items in this document and other items, the user of the TFT-LCD module and Sharp will cooperate and make efforts to solve the problems with mutual respect and good will.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible, for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 Fast Info: (1) 800-833-9437 www.sharpsma.com
SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com
SINGAPORE
SHARP Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com
TAIWAN
KOREA
SHARP Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328
SHARP Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855
SHARP Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819
CHINA
HONG KONG
SHARP Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp
SHARP-ROXY (Hong Kong) Ltd. 3rd Business Division, 17/F, Admiralty Centre, Tower 1 18 Harcourt Road, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 13B1, Tower C, Electronics Science & Technology Building Shen Nan Zhong Road Shenzhen, P.R. China Phone: (86) 755-3273731 Fax: (86) 755-3273735

▲Up To Search▲

Price & Availability of LQ038Q7DB03R

	To Download LQ038Q7DB03R Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .