View TES3-2410WI_4232762.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DC/DC Converters
TES 3WI Series, 3 Watt
Features Compact SMD package 33.4 x 18.8 mm footprint Ultra-wide 4:1 input voltage range I/O isolation 1500 VDC Operating temp. range -40 C to 71 C Short circuit protection Input filter to meet EN 55022, class A Remote On/Off High accuracy of pin co-planarity Qualified for leadfree reflow solder
process according IPC/JEDEC J-STD-020D
UL 60950-1 pending
Available in tape & reel package 3-year product warranty
The TES-3WI series is a family of high performance 3W dc/dc-converter modules in a low profile SMD package with compact dimensions. The 14 modules feature ultrawide 4:1 input ranges with tightly regulated output voltage. High efficiency allows an operating temperature range of -40 to +71C without derating. Further features are built-in EMI-filter to meet EN 55022 class A without external components and remote On/Off control. The products comply with IPC J-STD-020D and are qualified for high temperature lead-free reflow solder process.
Models
Ordercode TES 3-2410WI TES 3-2411WI TES 3-2412WI TES 3-2413WI TES 3-2421WI TES 3-2422WI TES 3-2423WI TES 3-4810WI TES 3-4811WI TES 3-4812WI TES 3-4813WI TES 3-4821WI TES 3-4822WI TES 3-4823WI 18 - 75 VDC (nominal 48 VDC) 9 - 36 VDC (nominal 24 VDC) Input voltage Output voltage 3.3 VDC 5 VDC 12 VDC 15 VDC 5 VDC 12 VDC 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 5 VDC 12 VDC 15 VDC Output current max. 750 mA 600 mA 250 mA 200 mA 300 mA 125 mA 100 mA 750 mA 600 mA 250 mA 200 mA 300 mA 125 mA 100 mA Efficiency typ. 75 % 79 % 81 % 81 % 78 % 81 % 81 % 76 % 80 % 83 % 83 % 80 % 83 % 83 %
http://www.tracopower.com
Page 1 of 4
DC/DC Converters
TES 3WI Series Input Specifications
Input current at full load Input current at full load Start-up voltage / under voltage shut down Surge voltage (1 sec. max.) Reverse voltage protection Reflected input ripple current Input filter 24 V models: 150 mA typ. 48 V models: 75 mA typ. 24 V models: 20 mA typ. 48 V models: 10 mA typ. 24 V models: 8.5 VDC / 8 VDC typ. 48 V models: 17 VDC / 16 VDC typ 24 V models: 50 V max. 48 V models: 100 V max. 1.0 A max. 24 V models: 10 mA typ. 48 V models: 5 mA typ. EN 55022 class A, FCC part 15, level A 1 % - Input variation Vin min. to Vin max. 0.5 % max. - Load variation 10 - 100 % single output models: 1.0 % max. dual output models balanced load: 2.0 % max. 10 % of rated max current (operation at lower load condition is safe but a higher output ripple will be experienced) 0.02 % / C max. 75 mVpk-pk max. 6 % max. peak variation 500 S max. response time 200 s typ. >120 % of Iout max. continuous, automatic recovery single output models: 3000 F dual output models: 180 F - On: - Off: - Off idle current: - Operating - Case temperature - Storage 2.5 to 5.5 V or open circuit -0.7 to 0.8 V or short circuit pin 3 and pin 1/2 5 mA -40C to +71 C +100C max. -40C to +125 C 95 % rel H max. >1`000`000 h 1`500 VDC 500 pF max. >1`000 Mohm 300 kHz typ. (frequency modulation PFM) UL 60950-1, EN 60950-1, IEC 60950-1 CSA File No. 226037 http://directories.csa-international.org (entry pending) - Input/Output - Input/Output - Input/Output
3 Watt
Output Specifications
Voltage set accuracy Regulation
Minimum load
Temperature coefficient Ripple and noise Dynamic load response 25% load change Transient response (25% load step change) Current limitation Short circuit protection Capacitive load Remote On/Off
General Specifications
Temperature ranges
Humidity (non condensing) Reliability, calculated MTBF (MIL-HDBK-217F, at 25C, ground benign) Isolation voltage (60 sec.) Isolation capacity Isolation resistance Switching frequency Safety standards Safety approvals
All specifications valid at nominal input voltage, full load and +25C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 4
DC/DC Converters
TES 3WI Series Physical Specifications
Case material Package weight Lead-free reflow solder process Moisture sensivity level (MSL) non conductive plastic (UL 94V-0 rated) 8.8 g (0.31 oz) as per IPC J-STD-020D as per IPC J-STD-033B MSL report level 2
www.tracopower.com/products/tes3wi_msl-report.pdf (publication pending)
3 Watt
Outline Dimensions
32.3 (1.272)
S
Seating Plane
Detail A
Pin-Out
Pin 1 2
14.8 (0.583) 16.1 (0.634) 18.8 (0.740)
10.2 (0.402)
Single -Vin (GND) -Vin (GND) NC NC NC NC +V Output NC -V Output NC +Vin (Vcc) +Vin (Vcc)
Dual -Vin (GND) -Vin (GND) NC Common NC -V Output + V Output NC Common NC +Vin (Vcc) +Vin (Vcc)
0.5 (0.02)
3 10 11 12 13 14 15 22
0.15
24
13
Detail A M10:1 Top View
.0 4)
1.
0
(0
1 2.16 2.54
(0.1)
12 17.78 (0.7) 1.3 (0.051) 1.0 (0.04)
0.15 (0.006)
23 24
(0.085)
Dimensions in [mm], () = Inch Tolerances 0.25 (0.01) Pin pitch tolerances 0.13 (0.005)
Solder Pad Dimensions
27.94 (1.1)
(0.09)
2.16
2.54 2.54
(0.1) (0.1)
17.78 (0.7)
2.54 2.54
(0.1) (0.1)
20.0 (0.79)
1
2.8 (0.11)
Dimensions in [mm], () = Inch
(0.06)
1.5 min.
http://www.tracopower.com
Page 3 of 4
DC/DC Converters
TES 3WI Series Packaging
Standard Packaging - Tube
- 1 tube contains 10 converters
11.0 12.0 15.5 360.0 2
3 Watt
5.0
1.0
12.6 22.0
Tolerance 0.25mm
1.75
Optional Packaging - Tape & Reel
- Specifications according IEC 286-3 - Use appendix -TR on order code.
52.4
4.0
A
2.0
0.5
5
r1 .5
10.0 29.5 32.7 56.0
56
- 1 reel contains 150 converters
26.5
R0.3 MAX
M
.75 R0
32.0 A
6.0 11.2 14.9 15.6 19.0 3.0
2.0
3.0
0.2
5
10.0
20
20
2.0
66.4
330.0 (13")
100.0
13.0 0.25
10.7
M: partial enlargement
Tolerance 0.1mm
Tolerance 1.0mm Dimensions in [mm] Specifications can be changed any time without notice.
Rev. 07/08
Jenatschstrasse 1 * CH-8002 Zurich * Switzerland Tel. +41 43 311 45 11 * Fax +41 43 311 45 45 * info@traco.ch * www.tracopower.com
Page 4 of 4

▲Up To Search▲

Price & Availability of TES3-2410WI

	To Download TES3-2410WI Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .