 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| celduc(R) r e l a i s S/CON/SOM040200/A/08/12/05 PRELIMINARY DATA Page 1/5 UK MOSFET BASED DC SOLID-STATE RELAY Latest MOSFET technology generation. Ultra low on-state resistance. Low output leakage current. Low control current consumption. Built-in overvoltage protection SOM040200 Reverse protected triggered control input to avoid linear control Control voltage risks No radiated or conducted disturbances Touch protected housing IP20 Load voltage range Load current range (with heatsink) range Max. permanent output voltage Max. load current with heatsink Dimensions (WxHxD) 45 x 58.5 x 30 3.5-32VDC 110VDC 40ADC Weight Control input voltage range In & case / Out Insulation Connections 5-110VDC Fig. 1 Up to 40A 3.5-32VDC 2.5kV Fig. 2 Screw terminals 80g HIGH SIDE WIRING DIAGRAM (Load connected to "-") LOW SIDE WIRING DIAGRAM (Load connected to "+") See Instruction sheet to select the right protective components The red paths (C1/D2) must be as short as possible ! See Instruction sheet for selective the right protective components The red paths (C1/D2) must be as short as possible ! Fig. 3 INTERNAL DIAGRAM Proud to serve you Data given at Tambient=25C and subject to modification without previous notice r celduc e l a i (R) s celduc(R) r e l a i s S/CON/SOM040200/A/08/12/05 PRELIMINARY DATA Page 2/5 UK CONTROL INPUT CHARACTERISTICS INPUT CIRCUIT CHARACTERISTIC Nom. Control voltage Min. Control current Control voltage range Control current consumption Releasing control voltage Max. reverse control voltage Input impedance LABEL Ucnom Icmin Uc Ic Ucoffmax -Ucmax Rin VALUE 12-24VDC 35mADC 3.5 - 32VDC 32 - 35mADC (for control voltage range) 1VDC 32VDC Current limitation INFO. -100A/C typical ON=3.3V See fig. 5 typical OFF= 2.6V -Icmax<100A See fig. 5 POWER OUTPUT CHARACTERISTICS CHARACTERISTIC Nominal voltage Voltage range Non-repetitive peak voltage Overvoltage protection Max reverse voltage drop (internal diode at OFF state) Maximum nominal currents Non-repetitive peak overload current Min. load current Max. leakage current Max. on-state resistance Typ. output capacitance Junction/case thermal resistance per power element Built-in heatsink thermal resistance vertically mounted Heatsink thermal time constant Control inputs/power outputs insulation voltage Inputs/case insulation voltage Outputs/case insulation voltage Isolation resistance Isolation capacitance Maximum junction temperature Storage ambient temperature Operating ambient temperature Max. case temperature LABEL Uenom Ut Utp D1 -Ut Ie max Id max Iemin Ielk max RDSon Cout Rthjc Rthra Tthra Uimp Uimp Uimp Rio Cio Tjmax Tstg Tamb Tc Resistive 40A 380A 5mA 3mA 46m 1.1nF 0.7K/W 10K/W 10 minutes 2.5kV 2.5kV 2.5kV 1G <8pF 175C -40->+100C -25->+90C 100C @Tra=75C @Tra=40C @Utmax @Tjmax @Iemax @Tjmax VALUE 90VDC 5-110VDC 200V Varistor 75V size 20 1.5V Motor Please contact us INFO. Ue @Ie=-56A @Uc=0 See fig. 7 (limits) See fig. 8 POWER CIRCUIT See fig. 7 PROTECTION CHARACTERISTICS Leakage current (Ielk) vs DC voltage (Ut) Ielk / Ie Absolute limits 1 Uto < Utp t max = 0.75 (Uto - Ut max) x Ie PROTECTION 0,8 0,6 0,4 0,2 0 0 20 40 60 80 100 120 140 160 180 200 Ut (V) U t max ( =U emax) Utp P ( protection ) = 1W max (Uto - Ut max) x Ie x t 1 T Utmax : Max. nominal voltage of the relay Uto : Possible overvoltage above Utmax Utn = Ue : User DC power supply voltage Ielk : Leakage current of the relay Ie : User load nominal current Utp : Relay max. non repetitive peak voltage t : Overvoltage duration T: Time between 2 overvoltage celduc(R) r e l a i s S/CON/SOM040200/A/08/12/05 PRELIMINARY DATA Page 3/5 UK TIME CHARACTERISTICS Fig. 4 TIME DIAGRAMS TIME CHARACT. CHARACTERISTIC Turn on time Turn on delay Turn off time Turn off delay Max. On-Off frequency LABEL ton tdon toff tdoff F(on-off) VALUE 20s 20s 20s 20s >1000Hz (for high frequency, take 2 x Ie to calculate the heatsink; the protections must be chosen carefully) INFO. Refer to the instruction sheet GENERAL INFORMATION CONNECTIONS Connections Screwdriver advised Min and max tightening torque Insulated crimp terminals (round tabs, eyelet type) Display 2 N.m M5 Power POZIDRIV2 1.2 N.m M4 Control Green LED (indicates relay has switched ON) UL94V0 2 screws (M4x12mm ; tightening = 1.2N.m) None 80g See mounting sheet MISC. Housing Mounting Noise level Weight STANDARDS GENERAL Standards Protection level Protection against direct touch CE marking UL, cULUS and VDE approvals TYPE OF TEST STANDARD EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-11 IEC60947-1 IP20 Yes Yes Pending LEVEL Pending Pending Pending Pending EFFECT ? ? ? ? E.M.C. IMMUNITY E.M.C. EMISSION E.S.D. (Electrostatic discharges) Radiated electromagnetic fields Fast transients bursts Electric chocks Voltage drop Radiated and conducted disturbances NFEN55011 Pending celduc(R) r e l a i s S/CON/SOM040200/A/08/12/05 PRELIMINARY DATA Page 4/5 UK CHARACTERISTIC CURVES Fig. 5 Ic (mADC) 50 45 40 35 30 25 20 15 10 5 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 Uc (VDC) 0 -50 0 50 100 150 INPUT CHARACTERISTIC Fig. 6 ON RESISTANCE VS JUNCTION TEMPERATURE -35C -35C 25C RDSon 60 (mOhms) 50 40 100C 30 20 10 Junction Temperature (C) Fig. 7 Permanent current Ie (ARMS) POWER DISSIPATED AND LOAD CURRENT LIMIT VS TEMPERATURE Please refer to the installation notice for precautions about mounting the device on a heatsink. Power dissipated (W) 45 1.2K/W 1.1K/W 0.9K/W 0.75K/W 0.55K/W 0.3K/W 97,8 77,3 59.2 43.5 30.2 19.3 10.9 4.8 1.2 8K/W 4K/W 2.2K/W 2.1K/W 40 35 30 25 20 15 10 5 0 0 10 20 30 40 50 60 70 80 90 100 0 110 Ambient temperature (C) 10K/W = No Heatsink 2.1K/W = WF210000 0.75K/W = WF070000 4K/W = 150x150x3mm aluminium sheet 1.2K/W = WF121000 0.55K/W = WF050000 2.2K/W = WF262100 1.1K/W = WF131100 0.3K/W = WF031100 2.2K/W = WF151200 0.9K/W = WF115100 Fig. 8 PEAK OVERLOAD CURRENT vs. PULSE DURATION CHARACTERISTIC Ie 320 (Apk) 280 240 200 160 120 Non-repetitive D=1% (Tc=100C, Tjmax=175C) Repetitive D=5% (Tc=100C, Tjmax=175C) Repetitive D=10% (Tc=100C, Tjmax=175C) Repetitive D=20% (Tc=100C, Tjmax=175C) t1 D(% ) = x 100 t2 80 40 0 0,1 Repetitive D=50% (Tc=100C, Tjmax=125C) 1 10 100 1000 Pulse duration (ms) celduc(R) r e l a i s S/CON/SOM040200/A/08/12/05 PRELIMINARY DATA Page 5/5 UK DIMENSIONS AND ACCESSORIES Fig. 9 DIMENSIONS (mm) 2 - 1 + Fig. 10 ACCESSORIES FASTON : Please contact us r celduc(R) e l a i s www.celduc.com Rue Ampere B.P. 4 42290 SORBIERS - France Phone : 33 (0) 4 77 53 90 20 Fax : 33 (0) 4 77 53 85 51 Email : celduc-relais@celduc.com |
Price & Availability of SOM040200
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |