View LZ0P3610_4434568.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LZ0P3610/3611/3612/3615
LZ0P3610/3611/ 3612/3615
DESCRIPTION
The LZ0P3610/11/12/15 are 1/4-type (4.5 mm) 270 000-pixel built-in lens color CCD (chargecoupled device) area sensors. With their small lens and WLCC-type flat package, it is possible to make ultra small color camera easily.
1/4-type Built-in Lens Color CCD Area Sensors with 270 k Pixels
Under development * Package - 14-pin half-pitch WLCC* type - Base section size : 12 mm (H) x 11 mm (V) - Outline dimensions (MAX.) : 18 mm (H) x 11 mm (V) * Package height - Approx. 10 mm (single lens) : LZ0P3610 - Approx. 13 mm (two pcs. of lenses) : LZ0P3611/12/15
* Window Leadless Chip Carrier
FEATURES
* Number of effective pixels : 512 (H) x 492 (V) * Number of optical black pixels - Horizontal : 2 front and 28 rear * Pixel pitch : 7.2 m (H) x 5.6 m (V) * Mg, G, Cy, and Ye complementary color filters * Low fixed-pattern noise and lag * Blooming suppression structure * Built-in output amplifier * Built-in overflow drain voltage circuit and reset gate voltage circuit * Horizontal shift register clock and reset gate clock voltage : 3.3 V (TYP.) * Variable electronic shutter (1/60 to 1/10 000 s) * Compatible with NTSC standard * Built-in optical low-pass-filter * Integrated lens : Horizontal viewing angle LZ0P3610 : 52 LZ0P3611 : 50 LZ0P3612 : 62 LZ0P3615 : 115
PIN CONNECTIONS
14-PIN HALF-PITCH WLCC TYPE TOP VIEW
OD ORS NC1 OS NC2 OH2 OH1
1 2 3 4 5 6 7
14 13 12 11 10 9 8
GND OV4 OV3 OV2 OV1 PW OFD
COMPARISON TABLE
Horizontal viewing angle Number of integrated lenses Package height Characteristics Lens specification LZ0P3610 52 Single Approx. 10 mm LZ0P3611 50 LZ0P3612 62 Two pcs. Approx. 13 mm Refer to each following specification. LZ0P3615 115
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
LZ0P3610/3611/3612/3615
PIN DESCRIPTION
SYMBOL OD OS ORS OV1, OV2, OV3, OV4 OH1, OH2 OFD PW GND NC1, NC2 PIN NAME Output transistor drain Output signals Reset transistor clock Vertical shift register clock Horizontal shift register clock Overflow drain P-well Ground No connection
ABSOLUTE MAXIMUM RATINGS
PARAMETER Output transistor drain voltage Overflow drain voltage Reset gate clock voltage Vertical shift register clock voltage Horizontal shift register clock voltage Voltage difference between P-well and vertical clock Voltage difference between vertical clocks Storage temperature Ambient operating temperature SYMBOL VOD VOFD VORS VOV VOH VPW-VOV VOV-VOV TSTG TOPR RATING 0 to +18 Internal output Internal output -10.5 to +17.5 -0.3 to +12 -28 to 0 0 to +15 -20 to +70 -10 to +60
(TA = +25 C)
UNIT V V V V V V V C C 3 NOTE 1 2
NOTES :
1. Do not connect to DC voltage directly. When OFD is connected to GND, connect VOD to GND. Overflow drain clock is applied below 26 Vp-p. 2. Do not connect to DC voltage directly. When ORS is connected to GND, connect VOD to GND. Reset gate clock is applied below 8 Vp-p. 3. When clock width is below 10 s, and clock duty factor is below 0.1%, voltage difference between vertical clocks will be below 27 V.
2
LZ0P3610/3611/3612/3615
RECOMMENDED OPERATING CONDITIONS
PARAMETER Ambient operating temperature Output transistor drain voltage Overflow drain clock p-p level Ground P-well voltage LOW level Vertical shift register clock INTERMEDIATE level HIGH level Horizontal shift register clock LOW level HIGH level SYMBOL TOPR VOD VOOFD GND VPW VOV1L, VOV2L VOV3L, VOV4L VOV1I, VOV2I VOV3I, VOV4I VOV1H, VOV3H VOH1L, VOH2L VOH1H, VOH2H VORS fOV1, fOV2 fOV3, fOV4 fOH1, fOH2 fORS 14.55 -0.05 3.0 3.0 MIN. 14.55 21.5 0.0 -9.0 -8.5 -8.0 0.0 15.0 0.0 3.3 3.3 15.73 9.53 9.53 15.45 0.05 5.25 5.25 VOVL -7.5 TYP. 25.0 15.0 MAX. 15.45 23.5 UNIT C V V V V V V V V V V kHz MHz MHz 1 1 2 NOTE
Reset gate clock p-p level Vertical shift register clock frequency Horizontal shift register clock frequency Reset gate clock frequency
NOTES :
* Connect NC1 and NC2 to GND directly or through a capacitor larger than 0.047 F. 1. Use the circuit parameter indicated in "SYSTEM CONFIGURATION EXAMPLE", and do not connect to DC voltage directly. 2. VPW is set below VOVL that is low level of vertical shift register clock, or is used with the same power supply that is connected to VL of V driver IC. * To apply power, first connect GND and then turn on VOD. After turning on VOD, turn on PW first and then turn on other powers and pulses. Do not connect the device to or disconnect it from the plug socket while power is being applied.
3
LZ0P3610/3611/3612/3615
CHARACTERISTICS FOR LZ0P3610 (Drive method : Field accumulation) (TA : +25 C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS". Color temperature of light source : 3 200 K)
PARAMETER Standard output voltage Saturation output voltage Sensitivity Resolution (at center) Resolution (at corner) Shading Difference of center position Output transistor drain current SYMBOL VO VSAT R MIN. 700 400 250 150 50 TYP. 150 500 300 200 65 4.0 10 8.0 MAX. UNIT mV mV mV TV line TV line % % mA NOTE 1 2 3 4 5 6 7
IOD
NOTES :
1. The average output voltage in the central area (H/10, V/10) under uniform illumination. The standard exposure conditions are defined as when VO is 150 mV. 2. The average output voltage in the central area (H/10, V/10) under 10 times exposure of the standard exposure conditions. 3. The average output voltage in the central area (H/10, V/10) when a 1 000 lux light source with a white board of 90% reflector is imaged. 4. The resolution in the central area (H/10, V/10) at which the image of the TV resolution chart (ex. EIAJ test chart) can be distinguished on the B/W video monitor. 5. The resolution in the peripheral area (image height : Y = 0.8) under the conditions mentioned above. 6. Defined by the following formula at the brightness of standard output voltage : (Vco/Vce) x 100 [%] Vco : Output voltage at edge of the image (at video output). Vce : Output voltage at center of the image (at video output). 7. The difference between the center position of image and that of the monitor. This is the ratio for the horizontal underscanning monitor size which includes the decentering eccentricity when turning the lens head one time.
LENS SPECIFICATION FOR LZ0P3610
PARAMETER Construction Focal length F No. Viewing angle TV distortion Focus adjustment range Torque of focusing SPECIFICATION Single (non-spherical, plastic) 4.0 mm [TYP. : reference] 2.85% H : 52, V : 40, Diagonal : 65 [TYP. : reference] -3.2% to 10 cm 0.00005 to 0.001 N*m NOTE
1 2 3
NOTES :
1. TV distortion is defined by the formula, (y/y) x 100 [%] at capturing rectangular pattern sized horizontal by vertical as 4 by 3. "y" is defined as the vertical height of the center of the horizontal line. y is defined as the difference between the vertical height of the center of the horizontal line and an edge of it.
y y
2. The best focus point of an object can be obtained by turning the lens head within this range. 3. Torques which are necessary for turning the lens. * Be careful not to remove the lens head by turning it counterclockwise too much when adjusting macro.
4
LZ0P3610/3611/3612/3615
CHARACTERISTICS FOR LZ0P3611 (Drive method : Field accumulation)
(TA : +25 C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS". Color temperature of light source : 3 200 K)
PARAMETER Standard output voltage Saturation output voltage Sensitivity Resolution (at center) Resolution (at corner) Shading Difference of center position Output transistor drain current SYMBOL VO VSAT R MIN. 700 400 250 150 40 TYP. 150 500 300 200 60 4.0 10 8.0 MAX. UNIT mV mV mV TV line TV line % % mA NOTE 1 2 3 4 5 6 7
IOD
NOTES :
1. The average output voltage in the central area (H/10, V/10) under uniform illumination. The standard exposure conditions are defined as when VO is 150 mV. 2. The average output voltage in the central area (H/10, V/10) under 10 times exposure of the standard exposure conditions. 3. The average output voltage in the central area (H/10, V/10) when a 1 000 lux light source with a white board of 90% reflector is imaged. 4. The resolution in the central area (H/10, V/10) at which the image of the TV resolution chart (ex. EIAJ test chart) can be distinguished on the B/W video monitor. 5. The resolution in the peripheral area (image height : Y = 0.8) under the conditions mentioned above. 6. Defined by the following formula at the brightness of standard output voltage : (Vco/Vce) x 100 [%] Vco : Output voltage at edge of the image (at video output). Vce : Output voltage at center of the image (at video output). 7. The difference between the center position of image and that of the monitor. This is the ratio for the horizontal underscanning monitor size which includes the decentering eccentricity when turning the lens head one time.
LENS SPECIFICATION FOR LZ0P3611
PARAMETER Construction Focal length F No. Viewing angle TV distortion Focus adjustment range Torque of focusing SPECIFICATION 2 pcs. (non-spherical, plastic) 3.9 mm [TYP. : reference] 2.85% H : 50, V : 38, Diagonal : 60 [TYP. : reference] -1.0% to 10 cm 0.00005 to 0.001 N*m NOTE
1 2 3
NOTES :
1. TV distortion is defined by the formula, (y/y) x 100 [%] at capturing rectangular pattern sized horizontal by vertical as 4 by 3. "y" is defined as the vertical height of the center of the horizontal line. y is defined as the difference between the vertical height of the center of the horizontal line and an edge of it.
y y
2. The best focus point of an object can be obtained by turning the lens head within this range. 3. Torques which are necessary for turning the lens. * Be careful not to remove the lens head by turning it counterclockwise too much when adjusting macro.
5
LZ0P3610/3611/3612/3615
Under development
CHARACTERISTICS FOR LZ0P3612 (Drive method : Field accumulation)
(TA : +25 C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS". Color temperature of light source : 3 200 K)
PARAMETER Standard output voltage Saturation output voltage Sensitivity Resolution (at center) Resolution (at corner) Shading Difference of center position Output transistor drain current SYMBOL VO VSAT R MIN. 700 400 250 150 TYP. 150 500 300 200 50 4.0 10 8.0 MAX. UNIT mV mV mV TV line TV line % % mA NOTE 1 2 3 4 5 6 7
IOD
NOTES :
1. The average output voltage in the central area (H/10, V/10) under uniform illumination. The standard exposure conditions are defined as when VO is 150 mV. 2. The average output voltage in the central area (H/10, V/10) under 10 times exposure of the standard exposure conditions. 3. The average output voltage in the central area (H/10, V/10) when a 1 000 lux light source with a white board of 90% reflector is imaged. 4. The resolution in the central area (H/10, V/10) at which the image of the TV resolution chart (ex. EIAJ test chart) can be distinguished on the B/W video monitor. 5. The resolution in the peripheral area (image height : Y = 0.8) under the conditions mentioned above. 6. Defined by the following formula at the brightness of standard output voltage : (Vco/Vce) x 100 [%] Vco : Output voltage at edge of the image (at video output). Vce : Output voltage at center of the image (at video output). 7. The difference between the center position of image and that of the monitor. This is the ratio for the horizontal underscanning monitor size which includes the decentering eccentricity when turning the lens head one time.
LENS SPECIFICATION FOR LZ0P3612
PARAMETER Construction Focal length F No. Viewing angle TV distortion Focus adjustment range Torque of focusing SPECIFICATION 2 pcs. (non-spherical, plastic) 3.0 mm [TYP. : reference] 2.85% H : 62, V : 49, Diagonal : 74 [TYP. : reference] -1.0% to 10 cm 0.00005 to 0.001 N*m NOTE
1 2 3
NOTES :
1. TV distortion is defined by the formula, (y/y) x 100 [%] at capturing rectangular pattern sized horizontal by vertical as 4 by 3. "y" is defined as the vertical height of the center of the horizontal line. y is defined as the difference between the vertical height of the center of the horizontal line and an edge of it.
y y
2. The best focus point of an object can be obtained by turning the lens head within this range. 3. Torques which are necessary for turning the lens. * Be careful not to remove the lens head by turning it counterclockwise too much when adjusting macro.
6
LZ0P3610/3611/3612/3615
Under development
CHARACTERISTICS FOR LZ0P3615 (Drive method : Field accumulation)
(TA : +25 C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS". Color temperature of light source : 3 200 K)
PARAMETER Standard output voltage Saturation output voltage Sensitivity Resolution (at center) Resolution (at corner) Shading Difference of center position Output transistor drain current SYMBOL VO VSAT R MIN. 700 400 TYP. 150 500 300 200 45 4.0 10 8.0 MAX. UNIT mV mV mV TV line TV line % % mA NOTE 1 2 3 4 5 6 7
IOD
NOTES :
1. The average output voltage in the central area (H/10, V/10) under uniform illumination. The standard exposure conditions are defined as when VO is 150 mV. 2. The average output voltage in the central area (H/10, V/10) under 10 times exposure of the standard exposure conditions. 3. The average output voltage in the central area (H/10, V/10) when a 1000 lux light source with a white board of 90% reflector is imaged. 4. The resolution in the central area (H/10, V/10) at which the image of the TV resolution chart (ex. EIAJ test chart) can be distinguished on the B/W video monitor. 5. The resolution in the peripheral area (image height : Y = 0.8) under the conditions mentioned above. 6. Defined by the following formula at the brightness of standard output voltage : (Vco/Vce) x 100 [%] Vco : Output voltage at edge of the image (at video output). Vce : Output voltage at center of the image (at video output). 7. The difference between the center position of image and that of the monitor. This is the ratio for the horizontal underscanning monitor size which includes the decentering eccentricity when turning the lens head one time.
LENS SPECIFICATION FOR LZ0P3615
PARAMETER Construction Focal length F No. Viewing angle TV distortion Focus adjustment range Torque of focusing SPECIFICATION 2 pcs. (non-spherical, plastic) 1.53 mm [TYP. : reference] 2.85% H : 115, V : 89, Diagonal : 138 [TYP. : reference] -14% to 10 cm 0.00005 to 0.001 N*m NOTE
1 2 3
NOTES :
1. TV distortion is defined by the formula, (y/y) x 100 [%] at capturing rectangular pattern sized horizontal by vertical as 4 by 3. "y" is defined as the vertical height of the center of the horizontal line. y is defined as the difference between the vertical height of the center of the horizontal line and an edge of it.
y y
2. The best focus point of an object can be obtained by turning the lens head within this range. 3. Torques which are necessary for turning the lens. * Be careful not to remove the lens head by turning it counterclockwise too much when adjusting macro.
7
LZ0P3610/3611/3612/3615
PIXEL STRUCTURE
OPTICAL BLACK (2 PIXELS) 512 (H) x 492 (V)
OPTICAL BLACK (28 PIXELS)
1 pin
COLOR FILTER ARRAY
(1, 492) (512, 492)
Mg Cy G Cy Mg Cy
G Ye Mg Ye G Ye
Mg Cy G Cy Mg Cy
G Ye Mg Ye G Ye
Mg Cy G Cy Mg Cy
G Ye Mg Ye G Ye
Mg Cy G Cy Mg Cy
G Ye Mg Ye G Ye
Mg Cy G Cy Mg Cy
G Ye Mg Ye G Ye
G Cy Mg Cy
ODD field
Mg Ye G Ye Mg Ye
G Cy Mg Cy G Cy
Mg Ye G Ye Mg Ye
G Cy Mg Cy G Cy
Mg Ye G Ye Mg Ye
G Cy Mg Cy G Cy
Mg Ye G Ye Mg Ye
G Cy Mg Cy G Cy
Mg Ye G Ye Mg Ye
(512, 1) EVEN field
G Cy
(1, 1)
8
LZ0P3610/3611/3612/3615
TIMING CHART
(ODD FIELD)
525 1 HD VD OV1 OV2 OV3 OV4 OOFD
484 486 488 490 492 + + + + 485 487 489 491 1 + 2 3 + 4 5 + 6 7 + 8 9 + 10 11 + 12
VERTICAL TRANSFER TIMING
10 17 19
Shutter speed 1/2 000 s
OS
(EVEN FIELD)
263 HD VD OV1 OV2 OV3 OV4 OOFD
483 485 487 489 491 + + + + + 484 486 488 490 492 1 2 + 3 4 + 5 6 + 7 8 + 9 10 + 11
272
279
282
OS
HORIZONTAL TRANSFER TIMING
606, 1 HD OH1 OH2 ORS OS ...512 OB (28) 29 OV1 39 OV2 24 OV3 34 OV4 62 OOFD 72 64 54 59 49 60
OB (2) OUTPUT (512) 1
9
LZ0P3610/3611/3612/3615
(ODD FIELD)
HD OV1 OV2 OV3 OV4 24 34 54 64 180 1 29 49 39 59 161 60
READOUT TIMING
606, 1 242 290 449 290 338 34 29 49 39 59 54 64 60
(EVEN FIELD)
HD OV1 OV2 OV3 OV4 24 34 54 64 180 290 338 450 54 64 1 29 49 39 59 161 60 242 290 59 606, 1 60
10
0.01 F
ORS OH2 OH1
+
1 M$
VOD VL (VPW) VH
CCD OUT
ORS
NC
OS
NC1
NC2
V1A
V1B
V3A
V3B
OH1
OH2
OD
POFD
12 11 10
VMa V4 V2 VL
VMb
VH
9
8
7
6
5
4
3
2
1
7
6
5
4
3
2
(*1)
SYSTEM CONFIGURATION EXAMPLE
1
+
LR36685
(*1)
LZ0P361X
8
OFD
11
13 14 15 16 17 18 19 20 21 22 23 24
V4X + V3X V1X V2X VDD GND VOFDH VH1BX VH3AX VH1AX VH3BX OFDX 100 $ 0.1 F
9
PW
10 11 12 13 14
OV1 OV2 OV3 OV4 GND
V4X
VH3AX
+
+5 V V3X VH1AX V1X V2X OFDX
LZ0P3610/3611/3612/3615
(*1) ORS, OFD : Use the circuit parameter indicated in this circuit example, and do not connect to DC voltage directly.
270 pF
1 M$
PACKAGES FOR CCD AND CMOS DEVICES
PACKAGES
14 WLCC TYPE
18-0.2 140.1 12
+0 -0.1 +0
(Unit : mm)
Approx. 10 0.8-0.05 2.00.1 4-90 5.00.1 1.27 1.6-0.05
+0 +0
0.64
1.27
,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,, ,,,, ,,,,
,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,,
11-0.1
+0
3.6
7.60.05
No.1 index
,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,,
,,,, ,,,, ,,,,
No.1 index 1.0 -0.1
+0
O11.0-0.1 O12.0
+0 -0.1
+0
2-C0.2 -0.05 1.00.1
+0
2-O0.8-0.05 11.00.05
+0
,, ,, ,, ,, ,,
,, ,, ,, ,, ,,
2.00.1
Height 0.5
,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,
5.00.1
Approx. 10
11.00.05
14 WLCC TYPE
18-0.2 14
0.1 +0 +0
1.00.1
Applicable models LZ0P3610/LZ0P3620
Approx.12-13 3.00.1 4-90 5.00.1 1.27 0.64 1.27
,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,, ,,,,,,,, ,,,,,,,,
,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,
11-0.1
+0
3.6
7.60.05
No.1 index
,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,
,,,,,,,, ,,,,,,,, ,,,,,,,,
No.1 index 2.00.1
O11.0-0.05 O12.0
,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,
+0
2-C0.2-0.05 2.00.1
+0
2-O0.8-0.05 110.05
+0
+0 -0.05
3.00.1
Height 0.5
5.00.1
Approx. 12
,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,, ,,, ,,, ,,, ,,, ,,, ,,, ,,,
11.00.05
1.00.1
Applicable models LZ0P3611/12/15, LZ0P3621/22/25, LZ0P3641/42/45/46
12
1.6 -0.05
12-0.1
+0
+0
0.8-0.05
PRECAUTIONS FOR BUILT-IN LENS CCD AREA SENSORS
PRECAUTIONS FOR BUILT-IN LENS CCD AREA SENSORS 1. Package Breakage
In order to prevent the package, the lens holder, and the lens from being broken, follow the instructions below : 1) The CCD is a precise optical component and the package-base material is ceramic. Therefore, o Take care not to drop the device when mounting, handling, or transporting. o Avoid giving a shock to the package. Especially when leads are fixed to the socket or the circuit board, a small shock could break the package more easily than when the package isn't fixed. 2) When adjusting the focus, screw the lens holder to the circuit board before soldering the leads. At that time, make sure to use a circuit board with plenty of strength, and to avoid the package and the lens holder from being broken, the following screw and clamp torque are recommended. o Recommended mounting screw : O1.7 tapping screw (B-tight type), Length, L = the thickness of the circuit board + 5 mm o Recommended clamp torque : 0.012 N*m [however, when the thickness of the circuit board is thinner than t = 2.0 mm] 3) If any damage or breakage occurs on the surface of the lens, its characteristics could deteriorate. Therefore, o Do not hit the lens. o Do not give a shock large enough to cause distortion. o Do not scrub or scratch the surface of the lens. - Even a soft cloth or applicator, if dry, could cause dust to scratch the lens.
2. Electrostatic Damage
As compared with general MOS-LSI, CCD has lower ESD. Therefore, take the following anti-static measures when handling the CCD : 1) Always discharge static electricity by grounding the human body and the instrument to be used. To ground the human body, provide resistance of about 1 M$ between the human body and the ground to be on the safe side. 2) When directly handling the device with the fingers, hold the lens holder and do not touch the lead. 3) To avoid generating static electricity, a. do not scrub the device with cloth or plastic. b. do not attach any tape or labels. c. do not clean the device with dust-cleaning tape. 4) When storing or transporting the device, put it in a container of conductive material.
3. Dust and Contamination
Dust or contamination on the surface of the lens and the inside of the lens holder could deteriorate the output characteristics or cause a scar. In order to minimize dust or contamination on the device, take the following precautions : 1) Do not remove the lens from the body. Especially when adjusting macro, be careful not to remove the lens by turning it counterclockwise too much. 2) Do not touch the surface of the lens with the fingers. If dust or contamination gets on the surface of the lens, the following cleaning method is recommended : o Handle the built-in lens CCD in a clean environment such as a cleaned booth. (The cleanliness level should be, if possible, class 1 000 at least.)
13
PRECAUTIONS FOR BUILT-IN LENS CCD AREA SENSORS
o Dust from static electricity should be blown off with an ionized air blower. For antielectrostatic measures, however, ground all the leads on the device before blowing off the dust. o The contamination on the surface of the lens should be wiped off with a clean applicator soaked in isopropyl alcohol. Wipe slowly and gently in one direction only. - Frequently replace the applicator and do not use the same applicator to clean more than one device.
THE SHAPE OF THE IRON END
R0.5 17 O3.2 (Unit : mm)
o Make sure there is no dust or contamination on the lens and screw it on the lens holder.
4. Other
1) Soldering should be manually performed under the following conditions : o Use ESD-measured soldering iron o The conditions of the soldering time in which the soldering iron touches the package, differs by the shape and the temperature of the iron end. Refer to the table below and take great care in soldering.
THE TEMPERATURE OF THE IRON END Below 350 C Below 300 C Below 275 C
SOLDERING TIME Time touching the package should be less than 40 seconds Time touching the package should be less than 25 seconds Time touching the package should be less than 35 seconds
6.5
0.5
17
(Unit : mm)
- In case where the soldering may exceed the time mentioned above, resume the work after the device returns to normal temperature. o Do not put too much force onto the lens and the lens holder while soldering. o Be careful not to let the soldering iron touch the lens holder. - Soldering can be quickly/neatly done by laying the soldering iron so it lightly touches the border between the package and the circuit board and sliding it in sideways.
2) There is no guarantee of the performance of the device which has been removed or resoldered after being soldered once under the conditions mentioned above. - In case there seems to be an inferior device, consult with our sales office before removing it. 3) Avoid using or storing the CCD at high temperature or high humidity as it is a precise optical component. Do not give a mechanical shock to the CCD. 4) Do not expose the device to strong light. For the color device, long exposure to strong light will fade the color of the color filters.
14

▲Up To Search▲

Price & Availability of LZ0P3610

	To Download LZ0P3610 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .