 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SMD 14 Pin Gull-Wing Quad TTL Compatible Active Delay Modules DELAY TIME 5% or 2 nS PART NUMBER DELAY TIME 5 or 2 nS PART NUMBER DELAY TIME 5% or 2 nS PART NUMBER 5 6 7 8 9 10 11 12 13 14 15 Whichever is greater. EPA366-5 EPA366-6 EPA366-7 EPA366-8 EPA366-9 EPA366-10 EPA366-11 EPA366-12 EPA366-13 EPA366-14 EPA366-15 16 17 18 19 20 21 22 23 24 25 30 EPA366-16 EPA366-17 EPA366-18 EPA366-19 EPA366-20 EPA366-21 EPA366-22 EPA366-23 EPA366-24 EPA366-25 EPA366-30 35 40 45 50 55 60 65 70 75 EPA366-35 EPA366-40 EPA366-45 EPA366-50 EPA366-55 EPA366-60 EPA366-65 EPA366-70 EPA366-75 Delay times referenced from input to leading edges at 25C, 5.0V, with no load. DC Electrical Characteristics Parameter Test Conditions VOH VOL VIK IIH IIL IOS ICCH ICCL TRO NH NL High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current Low-Level Input Current Short Circuit Output Current High-Level Supply Current Low-Level Supply Current Output Rise Time Fanout High-Level Output Fanout Low-Level Output VCC = min. VIL = max. I OH = max VCC = min. VIH = min. IOL= max VCC = min. II = IIK VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V VCC = max. VIN = 0.5V VCC = max. VOUT = 0. (One output at a time) VCC = max. VIN = OPEN VCC = max. VIN = 0 VCC = max. VOH = 2.7V VCC = max. VOL = 0.5V Schematic Min Max Unit 2.7 0.5 -1.2V 50 1.0 -2 -100 V V V A mA mA mA 14 VCC 12 10 1 9 3 -40 8 150 mA 150 mA 4 nS 20 TTL LOAD 10 TTL LOAD 4 5 7 GROUND Recommended Operating Conditions VCC VIH VIL IIK IOH IOL PW* d* TA Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature Package Dimensions Min 4.75 2.0 Max 5.25 0.8 -18 -1.0 20 Unit V V V mA mA mA % % C .055 .400 Max. 40 0 40 +70 PCA EPA366-5 Date Code .280 Max. Suggested Solder Pad Layout .410 .100 .780 Max. .250 Max. .01 Typ. .03 *These two values are inter-dependent. Input Pulse Test Conditions @ 25 C EIN PW TRI PRR VCC Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage 3.2 110 2.0 1.0 100 5.0 Unit Volts % nS MHz KHz Volts .02 .100 .050 .300 DSA366 Rev. A 2/5/96 QAF-CSO1 Rev. B 8/25/94 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = 1/32 16 .XX = .030 .XXX = .010 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791 |
Price & Availability of EPA366-10
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |