 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| S/MOT/SV969500/11/12/2001 INVERSEURS DE SENS DE ROTATION MOTOR REVERSER Le relais SV969500 est etudie pour demarrer et inverser le sens de rotation de moteurs triphases asynchrones , avec la commutation de 2 phases uniquement ( 4 commutateurs : 2 legs) . Le calibre des thyristors est de 75ARMS , ce qui permet de controler un moteur avec un courant nominal de 16ARMS soit 7,5kWatts sous 400VAC , en tenant compte des courants de demarrage et d'inversion. Ces produits sont realises avec des composants haute immunite , sans relais REED ( tout electronique) , avec toutes les protections : RC , VDR,... mais aussi interverouillage , temporisation entre chaque inversion,... Ces relais sont equipes de thyristors 1600V avec une protection adaptee pour des reseaux jusqu'a 550VRMS. The relay SV969500 is designed for controlling and inverting the direction of a three-phase motors without direct third leg ( two legs). The maximum current of semiconductors is 75 Amps. RMS , which allows a motor with a current rating of 16 Amps.rms or approximately 7,5 kW under 400 V , taking the starting and reversing current into account. These products are designed with very high immunity components , without REED switches (only composed of solid state components) , with all protections : RC , VDR ,..... temporisation ,........., and 1600Volt peak voltage components with on this model a voltage protection up to 550VRMS mains. Dimensions / Dimensions: 4,4 82,7 19 page 1 /5GB SV969500 3x400VAC 7,5KW two legs model Boitier IP20 IP20 housing M4 19 56,5 58,4 23 40 91 100 1L1 3x 400VAC Circuit equivalent/Equivalent circuit : Internal block diagram : 3L2 5L3 0V -A2/B2 M3,5 Forward Reverse Reverse Forward +B1 1L1 3L2 5L3 24-500VAC 8,5A AC53a (EN60947-1) With suitable heatsink See instruction sheet 1L1 3L2 5L3 Control logic +B1 -A2/B2 + B1 -A2/B2 EN60947-1 12-30VDC celduc France Solid State Motor Reverser +A1 RC -VDR protection R SV969300 2T1 2T1 4T2 6T3 Insulation (photocouplers) +A1 +A1 F 4T2 6T3 2T1 76 4T2 6T3 M3~ Proud to serve you All technical caracteristics are subject to change without previous notice. Caracteristiques sujettes a modifications sans preavis. celduc r e l a i s S/MOT/SV969500/11/12/2001 page 2 / 5 F/GB Synoptique interne / Internal diagram for two leg models : Forward Reverse 1L1 ~ LED Insu lation Switch RC network VDR 2T1 ~ 3L2 ~ Insu lation Switch RC network VDR 4T2 ~ Mains or load Load or mains Mains or load Load or mains Mains or load Load or mains Common A 2 /B2 Control lock Controls Reverse B1 + Forward A1 + Input circuit 5L3 ~ Insu lation Switch RC network VDR 6T3 ~ Insu lation Switch RC network VDR L3-T3 depending of models Developpe conformement aux normes / Designed in compliance with standards: ->EN60947-4-2 (V.D.E. 0660 part 109, I.E.C. 158-2) ->EN60947-1 & A11 ->EN60950 (V.D.E. 0805-> office equipment) (Pending approval) ->U.L. 508 (Pending approval) ->c.U.L (Pending approval) Plage de tension de commande / Control voltage range Plage de courant de commande / Control current range Tension de non fonctionnement/ Release voltage LED de visualisation / Display LED protection en cas de cdes simultanees / protection against simultaneous controls Control Uc Ic Ur tension inverse maxi / Maximum reverse voltage Signal de sortie / Output signal temporisation inversion / Reversing time Ui Ui Uimp Urv 12-30VDC 15-25mADC 6VDC Yes Yes 30V no output fixed 70ms 3300 3000 4000 Unit VRMS VRMS V Caracteristiques d'entree-sortie (a 20C) / Input-output characteristics (at 20C) Isolement entree-sortie/Input-output isolation @500m Isolement sortie-semelle/Output-case isolation @500m Tension assignee isolement/rated impulse voltage Caracteristiques generales / General characteristics Poids/Weight Plage de temperature de stockage / Storage temperature range Plage de temperature de fonctionnement/Operating temperature range 130g -40 / +100 -40 / +100 Unit g C C celduc r e l a i s www.celduc.com Rue Ampere B.P. 4 42290 SORBIERS - FRANCE E-Mail : celduc-relais@celduc.com Fax +33 (0) 4 77 53 85 51 Service Commercial France Tel. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tel. +33 (0) 4 77 53 90 19 S/MOT/SV969500/11/12/2001 page 3 / 5 F/GB Tension nominale/ Standard mains voltage Plage de tension de fonctionnement / Mains voltage range tension crete non repetitive/ Non-repetitive maximum peak voltage Courant AC-53 maxi/ Max. nom. current (AC53a=AC3) @40C Puissance moteur/ 3 pole power motor ( 3x400VAC) Chute directe / Max Direct voltage drop (@Ie) Courant crete non repetitif/ Non repetitive overload current (@ 1 cycle of 10ms) I2t value/ Melting limit (choice of fuse) @10ms Courant minimal de charge / Minimum load current facteur de puissance/ Power factor (@ Ie) Temps d'ouverture et de temporisation/ Turn on time-reversing time(@50Hz) Sortie/ Output Ue Un Up Ie Pn Ud ITSM I2t Imin Pf ton/trv toff Ilk dv/dt f 400 VAC 24-550VAC 1600V 16A 7,5kW 1,4VRMS 1000A 5000 A2s 100 mA 0 up to 1 20ms / 100ms 10ms 5 mARMS 500V/s 25 up to 440Hz Temps d'ouverture/ Turn off time (@50Hz) Courant de fuite /Maximum leakage current (@Ue/50Hz) dv/dt / Max off state voltage rise Frequence de reseau / Operating frequency range Max conducted immunity level Test accord. to I.E.C.1000-4-4 (bursts) Max conducted immunity level Test acc. to I.E.C.1000-4-5 (el. shocks) Max radiated immunity level Test accord. to I.E.C.1000-4-3 Max electrostatic disch. immunity level Test accord. to I.E.C.1000-4-2 Max conducted emission level (0,8 E.M.C. 10V/m no turn on or damage 8KV in the air / 4KV touching no turn on or damage The conducted noise made by SSR depends on the wiring configuration and the load type. Test methods recommended by European E.M.C. standards giving results far from reality, we have chosen to advise the right filter suited for the customer's use: Refer to EMC chapter <30dBV from 30 up to 230MHz ; <37dBV from 230 up to 1000MHz Misc. 0,5K/W (1 leg) 5K/W 130g Thin layer of thermal grease 91 40 Mounting of a relay on a heatsink Template r e l a i s Rue Ampere B.P. 4 42290 SORBIERS - FRANCE E-Mail : celduc-relais@celduc.com Fax +33 (0) 4 77 53 85 51 Service Commercial France Tel. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tel. +33 (0) 4 77 53 90 19 S/MOT/SV969500/11/12/2001 Caracteristiques thermiques / Thermal curves : 45 40 35 Total wasted power (W) 45 40 35 page 4 / 5 F/GB 2 30 25 20 15 10 5 0 0 5 10 15 RMS load current (A) 20 0 30 25 20 1 : without heatsink 2 : with WF121000 heatsink ( 1,2K/W) 1 15 10 5 0 10 20 30 40 50 60 70 80 90 100 Ambient temperature (C) Fig.3 Surcharge de courant : Itsm (Apeak) = f(t) pour modele 75A(Itsm=1000A) / Surge current : Itsm (Apeak) = f(t) for 75A models with Itsm =1000A 1500 Itsm (Apeak) 1 -Itsm non repetitif sans tension reappliquee est donne pour la determination des protections. No repetitive Itsm is given without voltage reapplied for the determination of the protection. 2 -Itsm repetitif est donne pour des surcharges de courant (Tj initiale=70C). La repetition de ces surcharges de courant diminue la duree de vie du Relais. Repetitive Itsm is given for inrush current with initial Tj = 70C. The repetition of the surge current decrease the lifetime SSR's . 1000 Surcharge de courant non repetitive sans tension reappliquee / No repetive surge current without voltage reapplied. Surcharge de courant repetitive avec tension reappliquee Repetive surge current with voltage reapplied. 500 0 0,01 0,1 t (s) 1 10 Precautions : * Les relais a semiconducteurs ne procurent pas d'isolation galvanique entre le reseau et la charge. Cautions : * Semiconductor relays don't provide any galvanic insulation between the load and the mains. SSR SELECTION motors soft-staters for a permanent current REVERSERS + HEATSINK SELECTION IN COMPLIANCE WITH EN60947-4-2 Heatsink Relays with Ferraz fuse Overload Relays without heatsink ambient =40C type relay type heatsink heatsink =80C 14x51 size / max. rating Klockner-Moeller Motor power In motor (@ 400V) two legs models 50A SG969300 -SV969300 SG969300 -SV969300 SG969300 -SV969300 SG969300 -SV969300 SG969300 -SV969300 SG969300 -SV969300 SV969500 SV969500 with integrated DIN RAIL adaptor two legs ambient =40C 0,75 kW 1,1 kW 1,5 kW 2,2 kW 3 kW 4 kW 5,5 kW 7,5 kW 2A 2,6A 3,5A 5A 6,6A 8,5A 12A 16A none none none WF121000 WF121000 WF121000 WF121000 WF121000 SW960330 SW960330 SW960330 SW961230 SW961230 SW961230 am 8A/500V am 8A/500V am 12A/500V am 12A/500V am 12A/500V am 12A/500V am 20A/500V am 32A/500V Z00-2.4 Z00-6 Z00-6 Z00-6 Z00-10 Z00-10 Z00-16 Z00-16 celduc r e l a i s www.celduc.com Rue Ampere B.P. 4 42290 SORBIERS - FRANCE E-Mail : celduc-relais@celduc.com Fax +33 (0) 4 77 53 85 51 Service Commercial France Tel. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tel. +33 (0) 4 77 53 90 19 S/MOT/SV969500/11/12/2001 Caracteristiques thermiques / Thermal curves : page 5 / 5 F/GB SV9 1 Cablage commande / Wiring of the control circuit: nombre de fils/ NUMBER OF WIRES 2 SCREWDRIVER TYPE tournevis tournevis MINIMUM TORQUE couple serrage SOLID FINE STRANDED SOLID FINE STRANDED (No ferrule) (With ferrule) (No ferrule) (With ferrule) rigide sans embout multibrins avec rigide sans embout multibrins avec embouts embouts N.m 0,75 ... 2,5 mm 2 0,75 ... 2,5 mm 2 0,75 ... 2,5 mm 2 0,75 ... 2,5 mm 2 0,8 x 5,5 mm POZIDRIV 2 1,2 SVT 1 Cablage puissance / Wiring of the power circuit: NUMBER OF WIRES 2 SCREWDRIVER TYPE tournevis tournevis MINIMUM TORQUE couple serrage SOLID FINE STRANDED SOLID FINE STRANDED (No ferrule) (With ferrule) (No ferrule) (With ferrule) rigide sans embout multibrins avec rigide sans embout multibrins avec embouts embouts N.m 1,5 ... 10 mm 2 1,5 ... 6 mm 2 1,5 ... 10 mm 2 1,5 ... 6 mm 2 0,8 x 5,5 mm POZIDRIV 2 ALIMENTATION MONOPHASE / Main voltage L N 1,8 Other application with one phase motor Reverse Forward 1L1 3L2 5L3 24-500VAC +B1 -A2/B2 EN60947-1 12-30VDC celduc France Solid State Motor Reverser 8,5A AC53a (EN60947-1) With suitable heatsink See instruction sheet 1L1 3L2 5L3 +A1 F R SV969300 2T1 2T1 4T2 4T2 6T3 6T3 Note : Le relais SV969300 developpe initialement pour inverser le sens de rotation des moteurs asynchrones triphases peut aussi etre utilise pour l'inversion de moteurs monophases . Ce relais possede 4 voies de puissance , une temporisation a l'inversion et un verrouillage en cas de commande simultanee . Pour des quantites importantes , en utilisation monophasee , le produit peut etre simplifie car seulement 2 voies sur 4 sont utilisees . Note : The SV969300 relay which has been initially developped in order to reverse three phase asynchronous motors , can be used for reversing single phase motors . This relay has 4 power switches , a reversing temporization and a lock in case of simultaneous controls . If you need a big quantity for a single phase use , please contact us , because we are able to simplify the product as only 2 switches among 4 are used . C M celduc r e l a i s www.celduc.com Rue Ampere B.P. 4 42290 SORBIERS - FRANCE E-Mail : celduc-relais@celduc.com Fax +33 (0) 4 77 53 85 51 Service Commercial France Tel. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tel. +33 (0) 4 77 53 90 19 |
Price & Availability of SV969500
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |