View 12104D107MAT4A_4589167.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

X5R Dielectric
General Specifications
GENERAL DESCRIPTION
* General Purpose Dielectric for Ceramic Capacitors * EIA Class II Dielectric * Temperature variation of capacitance is within 15% from -55C to +85C * Well suited for decoupling and filtering applications * Available in High Capacitance values (up to 100F)
PART NUMBER (see page 2 for complete part number explanation)
1210
Size (L" x W")
4
Voltage 4 = 4V 6 = 6.3V Z = 10V Y = 16V 3 = 25V D = 35V 5 = 50V
D
Dielectric D = X5R
107
Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros
M
Capacitance Tolerance K = 10% M = 20%
A
Failure Rate A = N/A
T
Terminations T = Plated Ni and Sn
2
Packaging 2 = 7" Reel 4 = 13" Reel 7 = Bulk Cass. 9 = Bulk
A
Special Code A = Std.
NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values.
TYPICAL ELECTRICAL CHARACTERISTICS
Insulation Resistance (Ohm-Farads)
Temperature Coefficient
20 15
Insulation Resistance vs Temperature
10,000
Capacitance
10 5 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 +60 +80
1,000
100
%
Temperature C
0 0
20
40
60
80
100
120
Temperature C
23
X5R Dielectric
Specifications and Test Methods
Parameter/Test Operating Temperature Range Capacitance Dissipation Factor X5R Specification Limits -55C to +85C Within specified tolerance 2.5% for 50V DC rating 3.0% for 25V DC rating 12.5% Max. for 16V DC rating and lower Contact Factory for DF by PN 100,000M or 500M - F, whichever is less No breakdown or visual defects No defects 12% Meets Initial Values (As Above) Initial Value x 0.3 95% of each terminal should be covered with fresh solder No defects, <25% leaching of either end terminal 7.5% Meets Initial Values (As Above) Meets Initial Values (As Above) Meets Initial Values (As Above) No visual defects 7.5% Meets Initial Values (As Above) Meets Initial Values (As Above) Meets Initial Values (As Above) No visual defects 12.5% Initial Value x 2.0 (See Above) Initial Value x 0.3 (See Above) Meets Initial Values (As Above) No visual defects 12.5% Initial Value x 2.0 (See Above) Initial Value x 0.3 (See Above) Meets Initial Values (As Above) Step 1: -55C 2 Step 2: Room Temp Step 3: +85C 2 Step 4: Room Temp 30 3 minutes 3 minutes 30 3 minutes 3 minutes Dip device in eutectic solder at 260C for 60 seconds. Store at room temperature for 24 2 hours before measuring electrical properties.
90 mm
Measuring Conditions Temperature Cycle Chamber Freq.: 1.0 kHz 10% Voltage: 1.0Vrms .2V For Cap > 10 F, 0.5Vrms @ 120Hz Charge device with rated voltage for 120 5 secs @ room temp/humidity Charge device with 300% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Deflection: 2mm Test Time: 30 seconds
1mm/sec
Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance
Resistance to Flexure Stresses
Solderability Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength
Dip device in eutectic solder at 230 5C for 5.0 0.5 seconds
Resistance to Solder Heat
Thermal Shock
Load Life
Repeat for 5 cycles and measure after 24 2 hours at room temperature Charge device with 1.5X rated voltage in test chamber set at 85C 2C for 1000 hours (+48, -0). Note: Contact factory for *optional specification part numbers that are tested at < 1.5X rated voltage. Remove from test chamber and stabilize at room temperature for 24 2 hours before measuring. Store in a test chamber set at 85C 2C/ 85% 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. Remove from chamber and stabilize at room temperature and humidity for 24 2 hours before measuring.
Load Humidity
24
X5R Dielectric
Capacitance Range
PREFERRED SIZES ARE SHADED
SIZE
Soldering Packaging
(L) Length (W) Width (t) Terminal MM (in.) MM (in.) MM (in.) WVDC 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 Cap (F) 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 10 22 47 100 WVDC
0201
Reflow Only All Paper
0.60 0.03 (0.024 0.001) 0.30 0.03 (0.011 0.001) 0.15 0.05 (0.006 0.002) 4 6.3 10 16 25 A A A A A A A A A A
0402
Reflow Only All Paper
1.00 0.10 (0.040 0.004) 0.50 0.10 (0.020 0.004) 0.25 0.15 (0.010 0.006) 4 6.3 10 16 25 50
0603
Reflow Only All Paper
0805
Reflow/Wave Paper/Embossed
1206
Reflow/Wave Paper/Embossed
1210
Reflow/Wave Paper/Embossed
1812
Reflow Only All Embossed
1.60 0.15 (0.063 0.006) 0.81 0.15 (0.032 0.006) 0.35 0.15 (0.014 0.006) 4 6.3 10 16 25 35 50 6.3
2.01 0.20 3.20 0.20 (0.079 0.008) (0.126 0.008) 1.25 0.20 1.60 0.20 (0.049 0.008) (0.063 0.008) 0.50 0.25 0.50 0.25 (0.020 0.010) (0.020 0.010) 10 16 25 35 50 6.3 10 16 25 35 50
3.20 0.20 4.50 0.30 (0.126 0.008) (0.177 0.012) 2.50 0.20 3.20 0.20 (0.098 0.008) (0.126 0.008) 0.50 0.25 0.61 0.36 (0.020 0.010) (0.024 0.014) 4 6.3 10 16 25 35 50 6.3 10 25 50
Cap (pF)
C C C C C C C C C C C C C G G G G G G G G G G G G G G G G G G G G G G N N N N N N N N N N N N* * N N N N N N N N N* Q Q Q Q Q Q Q Q Q P* Q Q Q Q N N Q Q Q Q Q Q Z Q Q X Z Z Z X X
L
W T
A A A A A A A A
t
C C C C C C C C C C C C C
N N N N N Q X X
G G G G G G J K G J G J G J
J
X
Z
4 6.3 10 16 25
4 6.3 10 16 25 50
4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50
ZZZZ Z Z Z* 4 6.3 10 16 25 35 50 6.3 10 25 50
SIZE
Letter Max. Thickness A 0.33 (0.013)
0201
C 0.56 (0.022) E 0.71 (0.028) PAPER
0402
G 0.90 (0.035) J 0.94 (0.037)
0603
K 1.02 (0.040) M 1.27 (0.050) N 1.40 (0.055)
0805
P Q 1.52 1.78 (0.060) (0.070) EMBOSSED
1206
X 2.29 (0.090) Y 2.54 (0.100)
1210
Z 2.79 (0.110)
1812
= Under Development *Optional Specifications - Contact factory NOTE: Contact factory for non-specified capacitance values
25

▲Up To Search▲

Price & Availability of 12104D107MAT4A

	To Download 12104D107MAT4A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .