 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HA1630Q04/05/06 Series Low Voltage Operation CMOS Quad Operational Amplifier REJ03D0803-0100 Rev.1.00 Mar 10, 2006 Description The HA1630Q04/05/06 are high slew rate single CMOS Operational Amplifiers realizing low voltage operation, low input offset voltage and low supply current. In addition to a low operating voltage from 1.8V, these device output can achieve full swing output voltage capability extending to either supply. Available in an ultra-small TSSOP-14 package that occupies only 1/4 the area of the SOP-14 package. Features * Low power and single supply operation * Low input offset voltage * Low supply current (per channel) VDD = 1.8 to 5.5 V VIO = 4.0 mV Max IDD = 200 A Typ (HA1630Q04) IDD = 400 A Typ (HA1630Q05) IDD = 800 A Typ (HA1630Q06) SR = 2 V/s Typ (HA1630Q04) SR = 4 V/s Typ (HA1630Q05) SR = 8 V/s Typ (HA1630Q06) VOH = 2.9 V Min (at VDD = 3.0 V) IIB = 1 pA Typ * High slew rate * Maximum output voltage * Low input bias current Ordering Information Type No. HA1630Q04T HA1630Q05T HA1630Q06T TTP-14D TTP-14D TTP-14D Package Name Package Code PTSP0014JA-B PTSP0014JA-B PTSP0014JA-B Rev.1.00 Mar 10, 2006 page 1 of 23 HA1630Q04/05/06 Series Pin Arrangement VOUT1 1 VIN1(-) 2 VIN1(+) 3 VDD 4 VIN2(+) 5 VIN2(-) 6 VOUT2 7 -+ +- -+ +- 14 VOUT4 13 VIN4(-) 12 VIN4(+) 11 VSS 10 VIN3(+) 9 VIN3(-) 8 VOUT3 Equivalent Circuit (per one channel) VDD VIN(-) VIN(+) VOUT VSS Rev.1.00 Mar 10, 2006 page 2 of 23 HA1630Q04/05/06 Series Absolute Maximum Ratings (Ta = 25C) Items Supply voltage Differential input voltage Input voltage Power dissipation Operating temp. Range Symbol VDD VIN(diff) VIN PT Topr Ratings 7 -VDD to +VDD -0.3 to +VDD 400 -40 to +85 Unit V V V mW C C Note 1 Storage temp. Range Tstg -55 to +125 Note: 1. Do not apply Input Voltage exceeding VDD or 7 V. Electrical Characteristics (VDD = 3.0 V, Ta = 25C) Items Input offset voltage Input offset current Input bias current Output high voltage Output source current Symbol VIO IIO IIB VOH IO SOURCE Min -- -- -- 2.9 100 200 400 -- -- -- -- -0.05 to 2.1 0 to 1.9 -- -- -- Voltage gain Gain bandwidth product AV BW 60 -- -- -- Power supply rejection ratio Common mode rejection ratio Supply current PSRR CMRR IDD 50 50 -- -- -- Typ -- (1.0) (1.0) -- 200 400 800 -- (5.0) (6.0) (6.5) -- -- (2.0) (4.0) (8.0) 90 (2100) (3300) (3600) 70 70 0.8 1.6 3.2 Max 4.0 -- -- -- -- -- -- 0.1 -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1.6 3.2 6.8 dB dB mA RL = (HA1630Q04) RL = (HA1630Q05) RL = (HA1630Q06) dB kHz Unit mV pA pA V A Test Condition Vin = 1.5 V Vin = 1.5 V Vin = 1.5 V RL = 100 k VOH = 2.5 V (HA1630Q04) VOH = 2.5 V (HA1630Q05) VOH = 2.5 V (HA1630Q06) RL = 100 k VOL = 0.5 V (HA1630Q04) VOL = 0.5 V (HA1630Q05) VOL = 0.5 V (HA1630Q06) (HA1630Q04, HA1630Q05) (HA1630Q06) CL = 20 pF (HA1630Q04) CL = 20 pF (HA1630Q05) CL = 20 pF (HA1630Q06) CL = 20 pF (HA1630Q04) CL = 20 pF (HA1630Q05) CL = 20 pF (HA1630Q06) Output low voltage Output sink current VOL IO SINK V mA Common mode input voltage range Slew rate VCM SR V V/s Notes: 1. In the case of continuous current flow, use a sink current of under 4 mA. 2. ( ) : Design specification Rev.1.00 Mar 10, 2006 page 3 of 23 HA1630Q04/05/06 Series Table of Graphs Electrical Characteristics Supply current Output high voltage Output source current Output low voltage Output sink current Input offset voltage IDD VOH IO SOURCE VOL IO SINK VIO vs Supply voltage vs Ambient temperature vs Output source current vs Supply voltage vs Ambient temperature vs Output sink current vs Ambient temperature Distribution vs Supply voltage vs Ambient temperature Common mode input voltage range Power supply rejection ratio Common mode rejection ratio Voltage gain & phase angle Input bias current Slew Rate (rising) Slew Rate (falling) Slew rate VCM PSRR CMRR AV IIB SRr SRf vs Ambient temperature vs Frequency vs Frequency vs Frequency vs Ambient temperature vs Input voltage vs Ambient temperature vs Ambient temperature Large signal transient response Small signal transient response (0 dB) (40 dB) vs. Output voltage p-p vs. Output voltage p-p vs Frequency vs Frequency HA1630Q04 Figure HA1630Q05 Figure HA1630Q06 Figure Test Circuit 2 4 6 5 6 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 1-21 1-22 1-23 1-24 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15 3-16 3-17 3-18 3-19 3-20 3-21 3-22 3-23 3-24 7 1 7 10 3 9 Total harmonic distortion + noise Maximum p-p output voltage Voltage noise density 8 Rev.1.00 Mar 10, 2006 page 4 of 23 HA1630Q04/05/06 Series Main Characteristics (HA1630Q04) Figure 1-1. HA1630Q04 Supply Current vs. Supply Voltage 400 Supply Current IDD (A) Supply Current IDD (A) Ta = 25C Figure 1-2. HA1630Q04 Supply Current vs. Ambient Temperature 400 300 200 100 0 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 300 200 100 0 1 2 3 4 5 Supply Voltage VDD (V) 6 -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 1-3. HA1630Q04 Output High Voltage vs. Output Source Current Output High Voltage VOH (V) Ta = 25C VDD = 5.5 V Figure 1-4. HA1630Q04 Output High Voltage vs. Supply Voltage Output High Voltage VOH (V) 6 5 4 3 VDD = 3.0 V 6 5 4 3 2 1 Ta = 25C VDD = 3.0 V RL = 100 k 2 1 0 0 100 200 300 Output Source Current IOSOURCE (A) VDD = 1.8 V 1 2 3 4 5 Supply Voltage VDD (V) 6 Figure 1-5. HA1630Q04 Output Source Current vs. Ambient Temperature 400 Output Source Current IOSOURCE (A) 300 200 100 0 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Rev.1.00 Mar 10, 2006 page 5 of 23 HA1630Q04/05/06 Series Figure 1-6. HA1630Q04 Output Low Voltage vs. Output Sink Current Figure 1-7. HA1630Q04 Output Sink Current vs. Ambient Temperature 10 VDD = 5.5 V VDD = 3.0 V Output Low Voltage VOL (V) 1.5 Output Sink Current IOSINK (mA) VDD = 5.5 V 8 6 4 1.0 VDD = 3.0 V VDD = 1.8 V 0.5 VDD = 1.8 V 2 0 -40 0 0 2 4 Output Sink Current IOSINK (mA) 6 -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 1-8. HA1630Q04 Input Offset Voltage Distribution Figure 1-9. HA1630Q04 Input Offset Voltage vs. Supply Voltage Input Offset Voltage VIO (mV) 40 Ta = 25C VDD = 3.0 V 4 3 2 1 0 -1 -2 -3 -4 1 2 Ta = 25C VIN = 0.5 V Percentage (%) 30 20 10 0 -4 -3 -2 -1 0 1 2 3 Input Offset Voltage VIO (mV) 4 3 4 5 Supply Voltage VDD (V) 6 Figure 1-10. HA1630Q04 Input Offset Voltage vs. Ambient Temperature Figure 1-11. HA1630Q04 Common Mode Input Voltage vs. Ambient Temperature 3.0 Input Offset Voltage VIO (mV) 4 VDD = 1.8 V, VIN = 0.9 V VDD = 3.0 V, VIN = 1.5 V 2 1 0 -1 -2 -3 -4 -40 -20 Common Mode Input Voltage VCM (V) 3 2.0 VDD = 3.0 V 1.0 0 VDD = 5.5 V, VIN = 2.75 V 0 20 40 60 80 100 -1.0 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Rev.1.00 Mar 10, 2006 page 6 of 23 HA1630Q04/05/06 Series Figure 1-12. HA1630Q04 Power Supply Rejection Ratio vs. Frequency Power Supply Rejection Ratio PSRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 1-13. HA1630Q04 Common Mode Rejection Ratio vs. Frequency Common Mode Rejection Ratio CMRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 1-14. HA1630Q04 Open Loop Voltage Gain and Phase Angle vs. Frequency 100 Open Loop Voltage Gain AVOL (dB) 225 Phase Angle (deg) Open Loop Voltage Gain Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 80 60 40 20 0 -20 -40 10 100 1k 180 135 90 Phase Angle Phase Margin: 57 deg 45 0 -45 10k 100k 1M -90 10M Frequency f (Hz) Rev.1.00 Mar 10, 2006 page 7 of 23 HA1630Q04/05/06 Series Figure 1-15. HA1630Q04 Input Bias Current vs. Ambient Temperature Input Bias Current IIB (pA) VDD = 3.0 V Figure 1-16. HA1630Q04 Input Bias Current vs. Input Voltage Input Bias Current IIB (pA) 200 100 0 -100 -200 200 100 0 -100 -200 Ta = 25C VDD = 3.0 V 0 25 50 75 Ambient Temperature Ta (C) 100 0 0.5 1.0 1.5 2.0 Input Voltage VIN (V) 2.5 3.0 Figure 1-17. HA1630Q04 Slew Rate (rising) vs. Ambient Temperature 5 Slew Rate SRr (V/s) Figure 1-18. HA1630Q04 Slew Rate (falling) vs. Ambient Temperature 5 Slew Rate SRf (V/s) VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 4 3 2 1 0 -40 VDD = 1.8 V VDD = 5.5 V VDD = 3.0 V 4 3 2 1 0 -40 -20 0 20 40 60 80 100 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Figure 1-19. HA1630Q04 Large Signal Transient Response 2.0 V Figure 1-20. HA1630Q04 Small Signal Transient Response 1.6 V Vin = 2.1 Vp-p, 250 kHz 0V Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF Vin = 0.2 Vp-p, 250 kHz 1.4 V Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF 2.0 V 1.6 V 0V 1.4 V Rev.1.00 Mar 10, 2006 page 8 of 23 HA1630Q04/05/06 Series Figure 1-21. HA1630Q04 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 T.H.D. + Noise (%) T.H.D. + Noise (%) VDD = 3.0 V Ta = 25C 1 Gain = 0 dB f = 10 kHz f = 1 kHz f = 100 Hz Figure 1-22. HA1630Q04 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 1 0.1 0.01 VDD = 3.0 V Ta = 25C Gain = 40 dB f = 10 kHz f = 1 kHz f = 100 Hz 0.1 0.01 0.001 0 0.5 1.0 1.5 0.001 2.0 2.5 3.0 0 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Output Voltage Vout p-p (V) Figure 1-23. HA1630Q04 Voltage Output p-p vs. Frequency Voltage Output Vout p-p (V) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1k 10k 100k Frequency f (Hz) 1M Gain = 40 dB, VIN = 0.03 Vp-p Gain = 20 dB, VIN = 0.3 Vp-p Ta = 25C VDD = 3.0 V Gain = 0 dB, VIN = 2.0 Vp-p 10M Figure 1-24. HA1630Q04 Voltage Noise Density vs. Frequency 200 Voltage Noise Density (nVms/Hz) VDD = 3.0 V Ta = 25C Gain = 40 dB RS = 1 k 160 120 80 40 0 100 1k Frequency f (Hz) 10k Rev.1.00 Mar 10, 2006 page 9 of 23 HA1630Q04/05/06 Series Main Characteristics (HA1630Q05) Figure 2-1. HA1630Q05 Supply Current vs. Supply Voltage 800 Supply Current IDD (A) Supply Current IDD (A) Ta = 25C Figure 2-2. HA1630Q05 Supply Current vs. Ambient Temperature 800 VDD = 5.5 V 600 400 200 0 1 2 3 4 5 Supply Voltage VDD (V) 6 600 400 200 0 -40 VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 2-3. HA1630Q05 Output High Voltage vs. Output Source Current Output High Voltage VOH (V) Ta = 25C VDD = 5.5 V Figure 2-4. HA1630Q05 Output High Voltage vs. Supply Voltage Output High Voltage VOH (V) 6 5 4 3 VDD = 3.0 V 6 5 4 3 2 1 Ta = 25C VDD = 3.0 V RL = 100 k RL = 20 k 2 1 0 0 100 200 300 400 500 Output Source Current IOSOURCE (A) VDD = 1.8 V 1 2 3 4 5 Supply Voltage VDD (V) 6 Figure 2-5. HA1630Q05 Output Source Current vs. Ambient Temperature 800 Output Source Current IOSOURCE (A) 600 400 200 0 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Rev.1.00 Mar 10, 2006 page 10 of 23 HA1630Q04/05/06 Series Figure 2-6. HA1630Q05 Output Low Voltage vs. Output Sink Current Figure 2-7. HA1630Q05 Output Sink Current vs. Ambient Temperature 10 VDD = 5.5 V VDD = 3.0 V Output Low Voltage VOL (V) 1.5 Output Sink Current IOSINK (mA) VDD = 5.5 V 8 6 4 1.0 VDD = 3.0 V VDD = 1.8 V 0.5 VDD = 1.8 V 2 0 -40 0 0 2 4 6 Output Sink Current IOSINK (mA) 8 -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 2-8. HA1630Q05 Input Offset Voltage Distribution Figure 2-9. HA1630Q05 Input Offset Voltage vs. Supply Voltage Input Offset Voltage VIO (mV) 40 Ta = 25C VDD = 3.0 V 4 3 2 1 0 -1 -2 -3 -4 1 2 Ta = 25C VIN = 0.5 V Percentage (%) 30 20 10 0 -4 -3 -2 -1 0 1 2 3 Input Offset Voltage VIO (mV) 4 3 4 5 Supply Voltage VDD (V) 6 Figure 2-10. HA1630Q05 Input Offset Voltage vs. Ambient Temperature Figure 2-11. HA1630Q05 Common Mode Input Voltage vs. Ambient Temperature 3.0 Input Offset Voltage VIO (mV) 4 VDD = 1.8 V, VIN = 0.9 V VDD = 3.0 V, VIN = 1.5 V 2 1 0 -1 -2 -3 -4 -40 -20 Common Mode Input Voltage VCM (V) 3 2.0 VDD = 3.0 V 1.0 0 VDD = 5.5 V, VIN = 2.75 V 0 20 40 60 80 100 -1.0 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Rev.1.00 Mar 10, 2006 page 11 of 23 HA1630Q04/05/06 Series Figure 2-12. HA1630Q05 Power Supply Rejection Ratio vs. Frequency Power Supply Rejection Ratio PSRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 2-13. HA1630Q05 Common Mode Rejection Ratio vs. Frequency Common Mode Rejection Ratio CMRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 2-14. HA1630Q05 Open Loop Voltage Gain and Phase Angle vs. Frequency 100 Open Loop Voltage Gain AVOL (dB) 225 Phase Angle (deg) Open Loop Voltage Gain Ta = 25C VDD = 3.0 V 180 RL = 1 M CL = 20 pF 135 80 60 40 20 0 -20 -40 10 100 1k 90 Phase Angle Phase Margin: 55 deg 45 0 -45 10k Frequency f (Hz) 100k 1M -90 10M Rev.1.00 Mar 10, 2006 page 12 of 23 HA1630Q04/05/06 Series Figure 2-15. HA1630Q05 Input Bias Current vs. Ambient Temperature Input Bias Current IIB (pA) Input Bias Current IIB (pA) Figure 2-16. HA1630Q05 Input Bias Current vs. Input Voltage 200 100 0 -100 -200 Ta = 25C VDD = 3.0 V 200 VDD = 3.0 V 100 0 -100 -200 0 25 50 75 Ambient Temperature Ta (C) 100 0 0.5 1.0 1.5 2.0 Input Voltage VIN (V) 2.5 3.0 Figure 2-17. HA1630Q05 Slew Rate (rising) vs. Ambient Temperature 10 Slew Rate SRr (V/s) Slew Rate SRf (V/s) Figure 2-18. HA1630Q05 Slew Rate (falling) vs. Ambient Temperature 10 VDD = 5.5 V VDD = 3.0 V 8 6 4 2 0 -40 VDD = 1.8 V VDD = 5.5 V VDD = 3.0 V 8 6 4 2 0 -40 VDD = 1.8 V -20 0 20 40 60 80 100 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Figure 2-19. HA1630Q05 Large Signal Transient Response Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF 1.6 V Figure 2-20. HA1630Q05 Small Signal Transient Response Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF 2.0 V VIN = 2.1 Vp-p, 500 kHz 0V VIN = 0.2 Vp-p, 500 kHz 1.4 V 2.0 V 1.6 V 0V 1.4 V Rev.1.00 Mar 10, 2006 page 13 of 23 HA1630Q04/05/06 Series Figure 2-21. HA1630Q05 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 T.H.D. + Noise (%) VDD = 3.0 V Ta = 25C Gain = 0 dB f = 10 kHz f = 1 kHz f = 100 Hz Figure 2-22. HA1630Q05 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 T.H.D. + Noise (%) f = 10 kHz f = 1 kHz f = 100 Hz 1 0.1 0.01 0.001 0 1 0.1 0.01 V = 3.0 V DD Ta = 25C Gain = 40 dB 0.001 0.5 1.0 1.5 2.0 2.5 3.0 0 Output Voltage Vout p-p (V) 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Figure 2-23. HA1630Q05 Voltage Output p-p vs. Frequency Voltage Output Vout p-p (V) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1k 10k 100k Frequency f (Hz) 1M 10M Gain = 40 dB, VIN = 0.03 Vp-p Gain = 20 dB, VIN = 0.3 Vp-p Gain = 0 dB, VIN = 2.0 Vp-p Ta = 25C VDD = 3.0 V Figure 2-24. HA1630Q05 Voltage Noise Density vs. Frequency 200 Voltage Noise Density (nVms/Hz) VDD = 3.0 V Ta = 25C Gain = 40 dB RS = 1 k 160 120 80 40 0 100 1k Frequency f (Hz) 10k Rev.1.00 Mar 10, 2006 page 14 of 23 HA1630Q04/05/06 Series Main Characteristics (HA1630Q06) Figure 3-1. HA1630Q06 Supply Current vs. Supply Voltage 1600 Supply Current IDD (A) Supply Current IDD (A) Ta = 25C Figure 3-2. HA1630Q06 Supply Current vs. Ambient Temperature 1600 VDD = 5.5 V 1200 800 400 0 1 2 3 4 5 Supply Voltage VDD (V) 6 1200 800 400 0 -40 VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 3-3. HA1630Q06 Output High Voltage vs. Output Source Current Output High Voltage VOH (V) Ta = 25C Figure 3-4. HA1630Q06 Output High Voltage vs. Supply Voltage Output High Voltage VOH (V) 6 5 VDD = 5.5 V 4 3 VDD = 3.0 V 6 5 4 3 2 1 Ta = 25C RL = 100 k RL = 20 k 2 1 0 0 200 400 600 800 1000 Output Source Current IOSOURCE (A) VDD = 1.8 V 1 2 3 4 5 Supply Voltage VDD (V) 6 Figure 3-5. HA1630Q06 Output Source Current vs. Ambient Temperature 1600 Output Source Current IOSOURCE (A) VDD = 5.5 V 1200 800 400 0 -40 VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Rev.1.00 Mar 10, 2006 page 15 of 23 HA1630Q04/05/06 Series Figure 3-6. HA1630Q06 Output Low Voltage vs. Output Sink Current Figure 3-7. HA1630Q06 Output Sink Current vs. Ambient Temperature 12 VDD = 3.0 V VDD = 5.5 V VDD = 3.0 V Output Low Voltage VOL (V) 1.5 Output Sink Current IOSINK (mA) VDD = 5.5 V 10 8 6 4 2 1.0 VDD = 1.8 V 0.5 VDD = 1.8 V 0 0 2 4 6 8 Output Sink Current IOSINK (mA) 10 0 -40 -20 0 20 40 60 80 Ambient Temperature Ta (C) 100 Figure 3-8. HA1630Q06 Input Offset Voltage Distribution Figure 3-9. HA1630Q06 Input Offset Voltage vs. Supply Voltage Input Offset Voltage VIO (mV) 40 Ta = 25C VDD = 3.0 V 4 3 2 1 0 -1 -2 -3 -4 1 2 Ta = 25C VIN = 0.5 V Percentage (%) 30 20 10 0 -4 -3 -2 -1 0 1 2 3 Input Offset Voltage VIO (mV) 4 3 4 5 Supply Voltage VDD (V) 6 Figure 3-10. HA1630Q06 Input Offset Voltage vs. Ambient Temperature Figure 3-11. HA1630Q06 Common Mode Input Voltage vs. Ambient Temperature 3.0 Input Offset Voltage VIO (mV) 4 VDD = 1.8 V, VIN = 0.9 V VDD = 3.0 V, VIN = 1.5 V 2 1 0 -1 -2 -3 -4 -40 -20 Common Mode Input Voltage VCM (V) 3 2.0 VDD = 3.0 V 1.0 0 VDD = 5.5 V, VIN = 2.75 V 0 20 40 60 80 100 -1.0 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Rev.1.00 Mar 10, 2006 page 16 of 23 HA1630Q04/05/06 Series Figure 3-12. HA1630Q06 Power Supply Rejection Ratio vs. Frequency Power Supply Rejection Ratio PSRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF VRIP = 0.1 Vp 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 3-13. HA1630Q06 Common Mode Rejection Ratio vs. Frequency Common Mode Rejection Ratio CMRR (dB) 100 80 60 40 20 0 10 Ta = 25C VDD = 3.0 V RL = 1 M CL = 20 pF 100 1k 10k Frequency f (Hz) 100k 1M 10M Figure 3-14. HA1630Q06 Open Loop Voltage Gain and Phase Angle vs. Frequency 100 Open Loop Voltage Gain AVOL (dB) 225 Open Loop Voltage Gain 60 40 Phase Angle 90 45 Phase Margin: 65 deg 20 0 -20 -40 10 100 1k 10k Frequency f (Hz) 100k 1M 0 -45 -90 10M Rev.1.00 Mar 10, 2006 page 17 of 23 Phase Angle (deg) 80 Ta = 25C VDD = 3.0 V 180 RL = 1 M CL = 20 pF 135 HA1630Q04/05/06 Series Figure 3-15. HA1630Q06 Input Bias Current vs. Ambient Temperature Input Bias Current IIB (pA) Input Bias Current IIB (pA) Figure 3-16. HA1630Q06 Input Bias Current vs. Input Voltage 200 100 0 -100 -200 Ta = 25C VDD = 3.0 V 200 VDD = 3.0 V 100 0 -100 -200 0 25 50 75 Ambient Temperature Ta (C) 100 0 0.5 1.0 1.5 2.0 Input Voltage VIN (V) 2.5 3.0 Figure 3-17. HA1630Q06 Slew Rate (rising) vs. Ambient Temperature 14 Slew Rate SRr (V/s) Figure 3-18. HA1630Q06 Slew Rate (falling) vs. Ambient Temperature 14 Slew Rate SRf (V/s) 12 10 8 6 4 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 12 10 8 6 4 -40 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V -20 0 20 40 60 80 100 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Figure 3-19. HA1630Q06 Large Signal Transient Response 2.0 V Figure 3-20. HA1630Q06 Small Signal Transient Response 1.6 V VIN = 1.9 Vp-p, 500 kHz 0V Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF VIN = 0.2 Vp-p, 500 kHz 1.4 V Ta = 25C VDD = 3.0 V RL = 100 k CL = 20 pF 2.0 V 1.6 V 0V 1.4 V Rev.1.00 Mar 10, 2006 page 18 of 23 HA1630Q04/05/06 Series Figure 3-21. HA1630Q06 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 T.H.D. + Noise (%) VDD = 3.0 V Ta = 25C Gain = 0 dB Figure 3-22. HA1630Q06 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 T.H.D. + Noise (%) 1 0.1 0.01 0.001 0 1 0.1 0.01 V = 3.0 V DD Ta = 25C Gain = 40 dB f = 10 kHz f = 1 kHz f = 100 Hz f = 10 kHz f = 1 kHz f = 100 Hz 0.001 0.5 1.0 1.5 2.0 2.5 3.0 0 Output Voltage Vout p-p (V) 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Figure 3-23. HA1630Q06 Voltage Output p-p vs. Frequency Voltage Output Vout p-p (V) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1k 10k 100k Frequency f (Hz) 1M Gain = 40 dB, VIN = 0.03 Vp-p Gain = 20 dB, VIN = 0.3 Vp-p Ta = 25C VDD = 3.0 V Gain = 0 dB, VIN = 2.0 Vp-p 10M Figure 3-24. HA1630Q06 Voltage Noise Density vs. Frequency 200 Voltage Noise Density (nVms/Hz) VDD = 3.0 V Ta = 25C Gain = 40 dB RS = 1 k 160 120 80 40 0 100 1k Frequency f (Hz) 10k Rev.1.00 Mar 10, 2006 page 19 of 23 HA1630Q04/05/06 Series Test Circuits 1. Power Supply Rejection Ratio, PSRP & Voltage Offset, VIO VDD RF RS - + VIO VIO = VO - PSRR VO PSRR = -20log VO1 - VO2 VDD1 - VDD2 x RS R S + RF VDD 2 x RS R S + RF VDD 2 RS Measure VO corresponding to VDD1 = 2.95 V and VDD2 = 3.05 V 2. Supply Current, IDD VDD A - + VDD 2 VDD 2 A - + 3. Input Bias Current, IIB VDD 4. Output High Voltage, VOH VDD VOH RL = 1 M VIN1 = VDD / 2 - 0.05 V VIN2 = VDD / 2 + 0.05 V - + VIN1 VIN2 RL VO 5. Output Low Voltage, VOL VDD VOL RL = 1 M VIN1 = VDD / 2 + 0.05 V VIN2 = VDD / 2 - 0.05 V - + VIN1 VIN2 RL VO Rev.1.00 Mar 10, 2006 page 20 of 23 HA1630Q04/05/06 Series 6. Output Source Current, IOSOURCE & Output Sink Current, IOSINK VDD IOSOURCE VO = VDD - 0.5 V VIN1 = VDD / 2 - 0.05 V VIN2 = VDD / 2 + 0.05 V A VO IOSINK VO = + 0.5 V VIN1 = VDD / 2 + 0.05 V VIN2 = VDD / 2 - 0.05 V - + VIN1 VIN2 7. Common Mode Input Voltage, VCM & Common Mode Rejection Ratio, CMRR VDD RF RS - + RF VDD 2 CMRR = -20log VO VO1 - VO2 VIN1 - VIN2 x RS RS + RF CMRR RS VIN Measure VO corresponding to VIN1 = 0 V and VIN2 = 2.1 V 8. Total Harmonic Distortion, THD VDD Gain Variable RS VIN RF - + Gain = +1 - + VIN VDD THD Gain Variable 1 + RF / RS = 100 freq = 100 Hz, 1 kHz, 10 kHz VO VO VSS VSS 9. Slew Rate, SR VDD 10. Gain, AV & Phase, GBW VDD RF RS - + 1 M VO 20 pF RS - + 1 M VO 20 pF VSS VSS Rev.1.00 Mar 10, 2006 page 21 of 23 HA1630Q04/05/06 Series Package Dimensions JEITA Package Code P-TSSOP14-4.4x5-0.65 RENESAS Code PTSP0014JA-B Previous Code TTP-14DV MASS[Typ.] 0.05g *1 D F 8 14 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. bp HE *2 E Index mark Terminal cross section ( Ni/Pd/Au plating ) 1 Z e *3 c 7 bp x M L1 Reference Symbol Dimension in Millimeters A1 L y Detail F D E A2 A1 A bp b1 c c1 HE e x y Z L L1 Min Nom Max 5.00 5.30 4.40 0.03 0.07 0.10 1.10 0.15 0.20 0.25 0.10 0.15 0.20 0 8 6.20 6.40 6.60 0.65 0.13 0.10 0.83 0.4 0.5 0.6 1.0 Rev.1.00 Mar 10, 2006 page 22 of 23 A HA1630Q04/05/06 Series Taping & Reel Specification [Taping] Package Code TSSOP-14 W 12 P 8 Ao 6.5 Bo 5.1 Ko 1.5 E F 5.5 D1 1.6 Maximum Storage No. 2,000 pcs/reel 1.5 Cover Tape A0 2.0 F 1.75 4.0 Unit: mm K0 B0 P Tape withdraw direction D1 W 17.4 [Ordering Information] Ordering Unit 2,000 pcs 2.0 13.4 2.0 Mark Indication 14 8 (1) to (4) (5),(8) to (10) (6), (7) (11), (12) (1) (2) (5) (8) (9) (3) (6) (4) (7) Week code Space Product Name 0Q04 0Q05 0Q06 HA1630Q04 HA1630Q05 HA1630Q06 (10) (11) (12) 1 Index hole 7 Rev.1.00 Mar 10, 2006 page 23 of 23 330 10 Tape width 12 W1 17.4 W2 13.4 13.0 0.5 [Reel] Package TSSOP-14 Sales Strategic Planning Div. Keep safety first in your circuit designs! Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 http://www.renesas.com Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 (c) 2006. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .6.0 |
Price & Availability of HA1630Q04
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |