View D114E_4811255.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

D100E Series
Low Cost, 1W SIP Single & Dual Output DC/DC Converters
Electrical Specifications
Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Key Features:
* 1W Output Power * Miniature SIP Case * UL Approved (File E245422) * Single & Dual Outputs * 1,000 VDC Isolation * >3.5 MHour MTBF * 24 Standard Models * LOWEST COST!!
Parameter Input Voltage Range Input Filter Reverse Polarity Input Current
Conditions 5 VDC Input 12 VDC Input 24 VDC Input
Min. 4.5 10.8 21.6
Typ. 5.0 12.0 24.0
Max. 5.5 13.2 26.4 0.3
Units VDC
Internal Capacitor A Units % % % 75 0.03 mV P - P % 0.02 Momentary (1.0 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 60 100 Conditions Ambient Min. -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +125 Typ. Max. Units VDC M pF kHz Units C C %/C
Output
Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit 120 Dual Output , Balanced Loads For Vin Change of 1% Conditions Min. Typ. 1.0 0.1 1.2 50 Max. 3.0 1.0
See Model Selection Guide
RoHS Compliant
General
Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency
Environmental
Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity
Physical
MicroPower Direct
292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com
Case Size Case Material Weight
0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Conditions MIL HDBK 217F, 25C, Gnd Benign Min. 3.5 Typ. Max. Units MHours
Reliability Specifications
Parameter MTBF Safety Standards Safety Approvals
UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Conditions 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 300 450 C mW VDC Units
Absolute Maximum Ratings
Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model Number D101E D102E D103E D104E D105E D106E D107E D108E D111E D112E D113E D114E D115E D116E D117E D118E D121E D122E D123E D124E D125E D126E D127E D128E Input Output Load Voltage (VDC) Current (mA) Regulation Voltage Current Current Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) 5 4.5 - 5.5 278 30 5.0 200.0 20.0 15 5 4.5 - 5.5 270 30 9.0 111.0 12.0 15 5 4.5 - 5.5 260 30 12.0 83.0 9.0 15 5 4.5 - 5.5 253 30 15.0 67.0 7.0 15 5 4.5 - 5.5 278 30 5.0 100.0 10.0 15 5 4.5 - 5.5 267 30 9.0 56.0 6.0 15 5 4.5 - 5.5 256 30 12.0 42.0 5.0 15 5 4.5 - 5.5 253 30 15.0 33.0 4.0 15 12 10.8 - 13.2 114 15 5.0 200.0 20.0 15 12 10.8 - 13.2 111 15 9.0 111.0 12.0 15 12 10.8 - 13.2 105 15 12.0 83.0 9.0 15 12 10.8 - 13.2 104 15 15.0 67.0 7.0 15 12 10.8 - 13.2 113 15 5.0 100.0 10.0 15 12 10.8 - 13.2 110 15 9.0 56.0 6.0 15 12 10.8 - 13.2 105 15 12.0 42.0 5.0 15 12 10.8 - 13.2 104 15 15.0 33.0 4.0 15 24 21.6 - 26.4 56 8 5.0 200.0 20.0 15 24 21.6 - 26.4 55 8 9.0 111.0 12.0 15 24 21.6 - 26.4 52 8 12.0 83.0 9.0 15 24 21.6 - 26.4 51 8 15.0 67.0 7.0 15 24 21.6 - 26.4 56 8 5.0 100.0 10.0 15 24 21.6 - 26.4 55 8 9.0 56.0 6.0 15 24 21.6 - 26.4 52 8 12.0 42.0 5.0 15 24 21.6 - 26.4 51 8 15.0 33.0 4.0 15 Efficiency (%, Typ) 72 74 77 79 72 75 78 79 73 75 79 80 74 76 79 80 74 76 80 81 74 76 80 81 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 100 100 100 100 100 100 100 100
Derating Curve
Other input/output combinations are available (i.e. 3.3 VDC). Contact the factory for details at: sales@micropowerdirect.com
Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor Output Capacitor Input be placed from the Vin Vout Capacitor Single Dual +Vout pin to the -Vout pin for single 5 VDC 4.7 F 5 VDC 10.0 F 4.7 F output units and 12 VDC 2.2 F 9 VDC 4.7 F 2.2 F from each output 24 VDC 1.0 F 12 VDC 2.2 F 1.0 F to common for dual 15 VDC 1.0 F 0.47 F output units. An input capacitor will enhance stability over temperature and input line variations. Recommended capacitor values are given in the table above. For applications requiring very low output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating.
Mechanical Dimensions
Pin Connections
Pin 1 2 4 Single +Vin -Vin -Vout Dual +Vin -Vin -Vout Pin 5 6 Single No Pin +Vout Dual Common +Vout
Notes: * All dimensions are typical in inches (mm) * Tolerance x.xx = 0.01 (0.25) * Pin 1 is marked by a "dot" or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
*
TEL: (781) 344-8226
*
FAX: (781) 344-8481
*
E-Mail: sales@micropowerdirect.com

▲Up To Search▲

Price & Availability of D114E

	To Download D114E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .