 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| M54HC373 RAD-HARD OCTAL D-TYPE LATCH WITH 3 STATE OUTPUT NON INVERTING s s s s s s s s s s s HIGH SPEED: tPD = 12ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 4A(MAX.) at TA=25C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS: tPLH tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 373 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9203-059 DILC-20 FPC-20 ORDER CODES PACKAGE DILC FPC FM M54HC373D M54HC373K EM M54HC373D1 M54HC373K1 DESCRIPTION The M54HC373 is an high speed CMOS OCTAL LATCH WITH 3-STATE OUTPUTS fabricated with sub-micron silicon gate C2MOS technology. This 8-BIT D-Type latches is controlled by a latch enable input (LE) and output enable input (OE). PIN CONNECTION While the LE input is held at a high level, the Q outputs will follow the data input. When the LE is taken low, the Q outputs will be latched at the logic level of D input data. While the OE input is at low level, the eight outputs will be in a normal logic state (high or low logic level) and when OE is in high level the outputs will be in a high impedance state. The 3-State output configuration and the wide choice of outline make bus organized system simple. All inputs are equipped with protection circuits against static discharge and transient excess voltage. May 2004 Rev. 1 1/11 M54HC373 Figure 1: IEC Logic Symbols Figure 2: Input And Output Equivalent Circuit Table 1: Pin Description PIN N 1 2, 5, 6, 9, 12, 15, 16, 19 3, 4, 7, 8, 13, 14, 17, 18 11 10 20 SYMBOL OE Q0 to Q7 D0 to D7 LE GND VCC NAME AND FUNCTION 3 State Output Enable Input (Active LOW) 3 State Outputs Data Inputs Latch Enable Input Ground (0V) Positive Supply Voltage Table 2: Truth Table INPUTS OE H L L L LE X L H H D X X L H OUTPUTS Q Z NO CHANGE (*) L H X: Don't Care Z: High Impedance (*): Q Outputs are latched at the time when the LE input is taken low logic level. 2/11 M54HC373 Figure 3: Logic Diagram Table 3: Absolute Maximum Ratings Symbol VCC VI VO IIK IOK IO PD Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 20 20 35 70 420 -65 to +150 265 Unit V V V mA mA mA mA mW C C ICC or IGND DC VCC or Ground Current Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied Table 4: Recommended Operating Conditions Symbol VCC VI VO Top tr, tf Supply Voltage Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time VCC = 2.0V VCC = 4.5V VCC = 6.0V Parameter Value 2 to 6 0 to VCC 0 to VCC -55 to 125 0 to 1000 0 to 500 0 to 400 Unit V V V C ns ns ns 3/11 M54HC373 Table 5: DC Specifications Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 VOL Low Level Output Voltage 2.0 4.5 6.0 4.5 6.0 II IOZ Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current 6.0 6.0 6.0 IO=-20 A IO=-20 A IO=-20 A IO=-6.0 mA IO=-7.8 mA IO=20 A IO=20 A IO=20 A IO=6.0 mA IO=7.8 mA VI = VCC or GND VI = VIH or VIL VO = VCC or GND VI = VCC or GND TA = 25C Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.18 5.68 2.0 4.5 6.0 4.31 5.8 0.0 0.0 0.0 0.17 0.18 0.1 0.1 0.1 0.26 0.26 0.1 0.5 4 1.9 4.4 5.9 4.13 5.63 0.1 0.1 0.1 0.33 0.33 1 5 40 Typ. Max. Value -40 to 85C Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.10 5.60 0.1 0.1 0.1 0.40 0.40 1 10 80 A A A V V Max. -55 to 125C Min. 1.5 3.15 4.2 0.5 1.35 1.8 Max. V Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage VIL V VOH ICC 4/11 M54HC373 Table 6: AC Electrical Characteristics (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 CL (pF) TA = 25C Min. Typ. 25 7 6 42 14 12 57 19 16 39 13 11 54 18 15 30 14 13 15 6 6 16 4 3 Max. 60 12 10 125 25 21 175 35 30 125 25 21 175 35 30 125 25 21 75 15 13 50 10 9 5 5 5 Value -40 to 85C Min. Max. 75 15 13 155 31 26 220 44 37 155 31 26 220 44 37 155 31 26 95 19 16 65 13 11 5 5 5 -55 to 125C Min. Max. 90 18 15 190 38 32 265 53 45 190 38 32 265 53 45 190 38 32 110 22 19 75 15 13 5 5 5 ns Unit tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (LE, D - Q) 50 50 ns 150 ns tPZL tPZH High Impedance Output Enable Time 50 RL = 1 K ns 150 RL = 1 K ns tPLZ tPHZ High Impedance Output Disable Time tW(H) Minimum Pulse Width (LE) Minimum Set-up Time Minimum Hold Time 50 RL = 1 K ns 50 ns ts 50 ns th 50 ns Table 7: Capacitive Characteristics Test Condition Symbol Parameter VCC (V) TA = 25C Min. Typ. 5 10 38 Max. 10 Value -40 to 85C Min. Max. 10 -55 to 125C Min. Max. 10 pF pF pF Unit CIN COUT CPD Input Capacitance Output Capacitance Power Dissipation Capacitance (note 1) 1) CPD is defined as the value of the IC's internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per Flip Flop) and the CPD when n pcs of Flip Flop operate, can be gained by the following equation: CPD(TOTAL) = 22 + 16 x n (pF) 5/11 M54HC373 Figure 4: Test Circuit TEST tPLH, tPHL tPZL, tPLZ tPZH, tPHZ CL = 50pF/150pF or equivalent (includes jig and probe capacitance) R1 = 1K or equivalent RT = ZOUT of pulse generator (typically 50) SWITCH Open VCC GND Figure 5: Waveform - LE To Qn Propagation Delays, Le Minimum Pulse Width, Dn To Le Setup And Hold Times (f=1MHz; 50% duty cycle) 6/11 M54HC373 Figure 6: Waveform - Output Enable And Disable Times (f=1MHz; 50% duty cycle) Figure 7: Waveform - Propagation Delay Times (f=1MHz; 50% duty cycle) 7/11 M54HC373 DILC-20 MECHANICAL DATA mm. DIM. MIN. A a1 a2 B b b1 D e e1 e2 e3 F I K L 11.30 1.14 1.27 22.73 7.62 7.29 2.1 3.00 0.63 1.93 0.40 0.20 25.14 7.36 0.88 2.03 0.45 0.254 25.40 7.62 2.54 22.86 7.87 7.49 22.99 8.12 7.70 3.86 11.56 1.40 0.445 0.045 0.050 0.895 0.300 0.287 TYP MAX. 2.71 3.70 1.14 2.23 0.50 0.30 25.65 7.87 MIN. 0.083 0.118 0.025 0.076 0.016 0.008 0.990 0.290 0.035 0.080 0.018 0.010 1.000 0.300 0.100 0.900 0.310 0.295 0.905 0.320 0.303 0.152 0.455 0.055 TYP. MAX. 0.107 0.146 0.045 0.088 0.020 0.012 1.010 0.310 inch 0016178J 8/11 M54HC373 FPC-20 MECHANICAL DATA mm. DIM. MIN. A B C D E F G H L M N O P 1.14 0.10 0.38 7.24 24.46 0.45 0.50 7.87 1.27 0.18 1.40 0.25 0.045 0.004 9.98 9.98 1.45 0.10 11.30 TYP 10.16 10.16 1.61 0.127 11.43 1.27 0.43 0.48 8.16 26.67 0.55 0.015 0.285 0.960 0.018 0.020 0.310 0.050 0.007 0.055 0.010 MAX. 10.34 10.34 1.78 0.18 11.56 MIN. 0.393 0.393 0.57 0.004 0.445 TYP. 0.400 0.400 0.63 0.005 0.450 0.050 0.017 0.019 0.320 1.050 0.022 MAX. 0.407 0.407 0.070 0.007 0.455 inch 016032F 9/11 M54HC373 Table 8: Revision History Date 10-May-2004 Revision 1 First Release Description of Changes 10/11 M54HC373 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners (c) 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 11/11 |
Price & Availability of M54HC37304
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |