View TS613_5020371.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TA0313 Technical Article
STMicroelectronics Solutions for ADSL Line Interfaces
New IGBT Driver
This paper describes STMicroelectronics ADSL analog line interface solutions. After a short overview of the ADSL application environment, this article focuses on the implementation of line drivers. Magnetic circuits such as hybrid or line transformer circuits will not be described in detail.
The ADSL concept
Asymmetric Digital Subscriber Line (ADSL) is a modem technology, which converts existing twisted-pair telephone lines into access paths for multimedia and high speed data communications. An ADSL modem is connected to a twisted-pair telephone line, creating three information channels: a high-speed downstream channel (up to 1.1MHz and 2.2MHz for ADSL2+) depending on the implementation of the ADSL architecture, a medium-speed upstream channel (up to 135kHz or 230kHz) and a POTS (Plain Old Telephone Service), split off from the modem by filters. Figure 1: Typical spectral representation of a DMT ADSL signal (subscriber side)
p.s.d. Power Spectral Density
Upstream
Downstream
DMT sub-channel (Discrete Multi-Tone)
POTS
4.5kHz
30kHz
135kHz
160kHz
1.1MHz
ADSL allows the wide-band access necessary to transmit media such as movies, television, remote CDROMs via LANs and the Internet into individual workplaces and homes.
TA0313/1104
1/9
TA0313
STMicroelectronics Solutions for ADSL Line Interfaces
The line interface - ADSL remote terminal (RT)
Figure 2 shows a typical analog line interface used for ADSL. The upstream and downstream signals are separated from the telephone line by using an hybrid circuit and a line transformer. On this note, emphasis will be placed on the emission path. Figure 2: Typical ADSL Line Interface
12.5
TX
TS613 TS612
12.5
TRANSMISSION
DMT
AFE
25
HYBRID
POTS SPLITTER
line
RECEPTION
RX
The emission path The features of the TS613 and TS612 drivers are shown in Table 1 below. Table 1: Features of drivers
GBP (MHz) BW Gain=4 MHz) 34 34 SR (V/s) Iout typ. (mA) Noise
(nV/Hz)
Icc per HD2/HD31 op. (dBc) (mA) 11 14 74/79 74/79
Vout diff. (Vpp min) 18 18
Packages
TS613 TS612
VFA VFA
130 130
40 40
320 320
3 3
SO8 SO8 Exposed Pad SO20 Batwing
1) Single ended 4Vpp/100kHz on 25//15pF
In order to shrink the line interface size, the TS613 comes in the classic SO8 plastic package as well as the SO8 ExposedPAD plastic package, capable of dissipating 1.7W at room temperature. While this circuit does not feature a power-down function, it does have the advantage of featuring a standard pinout.
2/9
STMicroelectronics Solutions for ADSL Line Interfaces
TA0313
Figure 3: Thermal considerations: power dissipation of the drivers vs. room temperature
5
TS612ID, Rthja=45C/W
Power dissipation (Watt)
4
3
TS613IPW, Rthja=70C/W
2
TS613ID, Rthja=175C/W
1
0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 Room Temperature (C)
The TS612 comes in SO20 plastic batwing package which increases its power dissipation capability to 2.7W at room temperature. It features a power-down or stand-by function in order to minimize the consumption when the modem is not in communication. Power Supply Remote ADSL modem terminals must be designed to be easily connected to a PC. For such applications, the driver should use a +12V single power supply, which is available via standard PCI connectors. Note that the TS613 and TS612 can also be powered by a dual power supply at +/-6V. Figure 4 shows a single +12V supply circuit with the TS613 as a remote terminal transmitter in differential mode. Note that one could also use the TS612 in exactly the same schema. Figure 4: Implementation of the TS613 as a differential line driver with a +12V single supply
1 100n 3 +12V 1k 2 8
+ _
+12V
1
12.5
10n
R2 3k9
1/2 R1
Vi
1:2 Vo 25 25
1/2 R1
Hybrid & Transformer
100
Vi
1k
10
3k9 100n 6 5
_
Vo
R4
7
+
GND
12.5
100n
4
GND
The driver is biased with a mid-supply (nominally +6V) in order to maintain the DC component of the signal at +6V. This allows a maximum dynamic range between 0 and +12 V. Several options are possible in order to provide this bias supply--such as for example, a virtual ground using an operational amplifier, or, the cheapest solution, a two-resistor divider. A high resistance value is required to limit the current consumption. On the other hand, the current must be high enough to bias the inverting input of the driver. If we consider the positive input's bias current (15A max) as 1% of the current through the resistance divider (1.5mA), two 3.9k resistors are sufficient to keep a stable mid-supply .
3/9
TA0313
STMicroelectronics Solutions for ADSL Line Interfaces
The input provides two high-pass filters with a break frequency of about 1.6kHz which is necessary to remove the DC component of the input signal. To avoid DC current flowing into the primary side of the transformer, an output capacitor is used. The 1F capacitance provides a path for low frequencies, the 10nF capacitance provides a path for high end of the spectrum. Filtering As the hybrid circuit cannot perfectly separate the upstream signal and the downstream signal, any distortion from the upstream signal could affect the downstream signal. For the upstream path, a lowpass filter becomes absolutely necessary in order to cut off the higher frequencies from the DAC analog output and the driver distortions. In this simple non-inverting amplification configuration, it is easy to implement a Sallen-Key low-pass filter by using the TS613 or TS612. Figure 5: Transmission path filtering
p.s.d. Power Spectral Density
D is to r tio n
U p s tre a m D o w n s t re am
POTS
30 kH z 1 3 0 k H z (o v e r P O T S ) 2 7 6 k H z (o v e r IS D N )
lo w p a s s filte r (tra n s m is s io n p a th )
A first solution is to use a LC cell before the driver to provide the low-pass filtering. Nevertheless, as shown in Figure 6, using 2nd order active filtering is a good solution especially as regards cost and space-saving considerations. Figure 6: TS613 line driver with 2nd order active filtering
C2
8 +12V
1
100n +12V 1k
R4
R5
3 2
+ _
12.5
10n
R2
C1
Vi
3k9
1/2 R1
Vo 25 25
1/2 R1
Vi
1k
10
3k9 100n
C3
Vo
6
_
GND
R6 R7
R3
7
12.5
5
+
100n
C4
4
GND
In the configuration shown in Figure 6, we assume R4=R6, R5=R7, C1=C3 and C2=C4.
4/9
STMicroelectronics Solutions for ADSL Line Interfaces
The resistances R1, R2 and R3 allow us to calculate the gain of the structure as follows: 2R2 2R 3 Gain = 1 + ---------- = 1 + ---------R1 R1
TA0313
The damping factor can be derived from these resistances and the capacitances C1, C2, C3 and C4: 2C 3 - C4 2 C1 - C2 = ---------------------------- = ---------------------------2 C3C 4 2 C1C 2 with: 2R3 2R 2 = ---------- = ---------R1 R1 The higher the gain, the more sensitive the damping factor is. When the gain is higher than 1 it is preferable to use very stable resistance and capacitance values. The value of the gain does not affect the cut-off frequency, fc, which is derived as follows: 1 1 fc = ------------------------------------------- = ------------------------------------------2 R4R5C 1C2 2 R6R7C3C 4 Moreover this expression shows that it is possible to shift the cut-off frequency by simply changing the values of the resistances R4, R5 or R6, R7 -- with neither a change of capacitance nor of the damping factor. The following table shows a calculations of components for a cut-off frequency around 130kHz for the ADSL over POTS and 270kHz for the ADSL over ISDN. The final, accurate settings are made by compromising between the attenuation of the highest frequencies of the upstream signal and the impact of the distortion on the downstream signal. This is best done directly in the application. Nevertheless we can start with the following initial values:
R1 () 180 180 R2 R3 () 536 536 R4 R6 () 261 127 R5 R7 () 261 127 C1 C3 (nF) 10 10 C2 C4 (nF) 2.2 2.2 Gain (dB) 16.8 16.8 fc (kHz) 130 270
0.73 0.73
Transformation ratio In differential mode, the TS613 and TS612 are able to deliver a typical amplitude signal of 18V peak to peak. The dynamic line impedance is 100. The typical value of the amplitude signal required on the line is up to 12.4V peak to peak. By using a 1:2 transformer ratio the reflected impedance back to the primary will be a quarter (25) and therefore the amplitude of the signal required with this impedance will be halved (6.2 V peak to peak). Assuming a 25 series resistance (12.5 for both outputs) is necessary for impedance matching, the output signal amplitude required is 12.4V peak to peak. This value is acceptable for both TS613 and TS612. In this case, the load impedance is 25 for each driver in single ended.
5/9
TA0313
STMicroelectronics Solutions for ADSL Line Interfaces
Increasing the line level by using an active impedance matching With passive matching, the output signal amplitude of the driver must be twice the amplitude on the load. To go beyond this limitation an active matching impedance can be used. With this technique it is possible to maintain good impedance matching with an amplitude on the load higher than half of the output driver amplitude. This concept is shown in Figure 7 for a differential line. Figure 7: TS613 as a differential line driver with an active impedance matching
1 100n 3 +12V 1k 2 8
+ _
+12V
1
Rs1
Vo
10n
R2 3k9
1/2 R1
Vi
1:2
R3
Vo 25 25
Hybrid & Transformer
100
1/2 R1
R5
Vi
1k
10
3k9
100n
Vo
6 5
_
GND
R4
7
Vo
Rs2
+
100n
4
GND
Component calculation Let us consider the equivalent circuit for a single-ended configuration, as shown in Figure 8. Figure 8: Single ended equivalent circuit
+
Rs1 Vi
_
R2
Vo
Vo
-1
R3
1/2R1 1/2RL
For unloaded system, we can assume that currents through R1, R2 and R3 are respectively: 2Vi ( Vi - Vo ) ( Vi + Vo ) -------- , -------------------------- and -----------------------R1 R2 R3
6/9
STMicroelectronics Solutions for ADSL Line Interfaces
As Vo equals Vo without loading, the gain in this case becomes: 2R2 R2 1 + ----------- + ------Vo ( noloa d ) R1 R3 G = -------------------------------- = -----------------------------------Vi R2 1 - ------R3 The gain for the loaded system will be: 2 R2 R2 1 + ----------- + ------Vo ( w ithload ) 1 R 1 R3 GL = ------------------------------------- = -- -----------------------------------Vi 2 R2 1 - ------R3
TA0313
Equation 1
As shown in Figure 9, this system is an ideal generator, with a synthesized impedance equal to the internal impedance of the system. Therefore, the output voltage becomes: Equation 2 Vo = ( ViG ) - ( Ro Io ut )
with Ro the synthesized impedance and Iout the output current. On the other hand Vo can be expressed as: Equation 3 2R2 R 2 Vi 1 + ----------- + ------- R1 R 3 Rs1Io ut Vo = ----------------------------------------------- - ---------------------R2 R2 1 - ------1 - ------R3 R3
Figure 9: Equivalent schematic, where Ro is the synthesized impedance
Ro Iout
Vi.Gi
1/2RL
By identifying of both Equation 2 and Equation 3, the synthesized impedance is, with Rs1=Rs2=Rs: Equation 4 Rs Ro = ---------------R2 1 - -----R3
Unlike the level of Vo required for passive impedance, Vo will be smaller than 2Vo in this case. Let us write Vo=kVo with k the matching factor varying between 1 and 2. Assuming that the current through R3 is negligible, the resistance divider becomes: kVoR L Ro = ---------------------------RL + 2R s1 After choosing the k factor, Rs will equal to 1/2RL(k-1).
7/9
TA0313
STMicroelectronics Solutions for ADSL Line Interfaces
A good impedance matching assumes: Equation 5 From Equation 3 and Equation 5 we derive: Equation 6 R2 2Rs ------ = 1 - ---------R3 RL 1 R o = -- RL 2
By fixing an arbitrary value for R2 in Equation 6, we arrive at: R2 R3 = ------------------2Rs 1 - ---------RL Finally, the values of R2 and R3 allow us to extract R1 from Equation 1 so that: Equation 7 2R2 R 1 = -------------------------------------------------------R2 R2 2 1 - ------- G L - 1 - ----- R3 R3
with GL the required gain.
GL (gain for the loaded system) R1 R2 (=R4) R3 (=R5) Rs GL is fixed for the application requirements GL=Vo/Vi=0.5(1+2R2/R1+R2/R3)/(1-R2/R3) 2R2/[2(1-R2/R3)GL-1-R2/R3] Arbitrarily fixed R2/(1-Rs/0.5RL) 0.5RL(k-1)
Capabilities The table below shows the calculated components for different values of k for a differential load of 25. In all cases, R2=1000 and the gain=16dB. The last column displays the maximum amplitude level on the line regarding the TS613 maximum output capabilities (18Vp-p diff.) and a 1:2 line transformer ratio.
Active matching k 1.3 1.4 1.5 1.6 1.7 R1 () 953 590 422 316 261 R3 () 1400 1620 2000 2490 3300 Passive matching Rs () 3.75 (3.9//100) 5 (10//10) 6.36 (6.8//100) 7.57 (8.2//100) 8.71 (10//68) TS613 Output Level to get 12.4Vpp on the line with a turn ratio of 2. (Vp-p diff) 8.06 8.68 9.35 9.95 10.52 12.4 Maximum Line Level (Vp-p diff) 27.5 25.7 25.3 23.7 22.3 18
Measurement of power consumption in application Conditions:
l Passive impedance matching l Transformer turns ratio: 2 l Maximum level required on the line: 12.4Vpp l Maximum output level of the driver: 12.4Vpp
8/9
STMicroelectronics Solutions for ADSL Line Interfaces
l Crest factor: 5.3 (Vp/Vrms) l Power Supply: 12V
TA0313
Power consumption of the driver during emission on 900 and 4550 meter twisted pair telephone lines:
l TS613: 360mW l TS612: 450mW
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners (c) 2004 STMicroelectronics - All rights reserved
STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
9/9

▲Up To Search▲

Price & Availability of TS613

	To Download TS613 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .