View HMC892LP5E_5026076.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HMC892LP5E
v00.0910
FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz
Features
Fast Tuning Response; 200 ns Excellent Wideband Rejection; >30 dB Single Chip Replacement for Mechanically Tuned Designs 32 Lead 5x5 mm SMT Package
3
FILTERS - TUNABLE - SMT
Typical Applications
The HMC892LP5E is ideal for: * Test & Measurement Equipment * Military RADAR & EW/ECM * SATCOM & Space * Industrial & Medical Equipment
Functional Diagram
General Description
The HMC892LP5E is a MMIC band pass filter which features a user selectable passband frequency. The 3 dB filter bandwidth is approximately 9%. The 20 dB filter bandwidth is approximately 23%. The center frequency can be varied between 4 and 7.7 GHz by applying an analog tune voltage between 0 and 14V. This tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. The HMC892LP5E has excellent microphonics due to the monolithic design, and provides a dynamically adjustable solution in advanced communications applications.
Electrical Specifications, TA = +25C, Vfctl = Vbwctl Unless Otherwise Stated
Parameter Fcenter Tuning Range 3 dB Bandwidth Low Side Rejection Frequency (Rejection >20 dB) High Side Rejection Frequency (Rejection >20 dB) Re-entry Frequency (Rejection <30 dB) 3 dB Bandwidth Control (Vbwctl) Insertion Loss Return Loss Maximum Input Power for Linear Operation Frequency Control Voltage (Vfctl) Source/Sink Current (Ifctl) Bandwidth Control Voltage (Vbwctl) Source/Sink Current (Ibwctl) Residual Phase Noise [1] (1 MHz Offset) Fcenter Drift Rate Tuning Characteristics [2] tFULLBAND (0% Vfctl to 90% RF) -165 -0.65 200 0 0 Min. 4 9 0.9*Fcenter 1.13*Fcenter 2.5*Fcenter 3 8 9 10 14 1 14 1 Typ. Max. 7.7 Units GHz % GHz GHz GHz % dB dB dBm V mA V mA dBc/Hz MHz/C ns
[1] Optimum residual phase noise performance requires the use of a low noise driver circuit. [2] Tuning speed is dependent on driver circuit. Data measured with a high speed op-amp driver and includes driver slew rate delay.
3-1
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC892LP5E
v00.0910
FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz
Broadband Insertion Loss vs. Control Voltages, Vfctl = Vbwctl
0 -10 0V 7V 14V
Broadband Return Loss vs. Control Voltages, Vfctl = Vbwctl
0 -5
3
FILTERS - TUNABLE - SMT
3-2
INSERTION LOSS (dB)
-20 -30 -40 -50 -60 -70 0 5 10 15 20 25 30
RETURN LOSS (dB)
-10 S11 S22
-15
-20
-25
0V 7V 14V
5 10 15 20 25 30
-30 0
FREQUENCY (GHz)
FREQUENCY (GHz)
Insertion Loss vs. Control Voltages, Vfctl = Vbwctl
0 -2
Return Loss vs. Control Voltages, Vfctl = Vbwctl
0 -5
INSERTION LOSS (dB)
-4 -6 -8 -10 -12 -14 -16 -18 -20 3 4 5 6 7 8 9 0V 7V 14V
RETURN LOSS (dB)
-10
-15
0V
-20
7V
14V
-25
S11 S22
-30 3 4 5 6 7 8 9
FREQUENCY (GHz)
FREQUENCY (GHz)
Insertion Loss vs. Temperature, Vfctl = Vbwctl = 7V
0 -2
Return Loss vs. Temperature, Vfctl = Vbwctl = 7V
0 -5
INSERTION LOSS (dB)
-4 -6 -8 -10 -12 -14 -16 -18 -20 3 4 5 6 7 8 9 +25C +85C -40C
RETURN LOSS (dB)
S11
-10
-15
S22
-20 +25C +85C -40C
-25
-30 3 4 5 6 7 8 9
FREQUENCY (GHz)
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC892LP5E
v00.0910
FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz
3
FILTERS - TUNABLE - SMT
Broadband Insertion Loss vs. Vbwctl, Vfctl = 7V
0 -10 Vbwctl=4V Vbwctl=7V Vbwctl=10V
Broadband Return Loss vs. Vbwctl, Vfctl = 7V
0 -5
Vbwctl=4V
INSERTION LOSS (dB)
RETURN LOSS (dB)
-20 -30 -40 -50 -60 -70 -80 0 5 10 15 20
-10 -15 -20 -25 -30 -35
Vbwctl=10V
S11 S22
Vbwctl=7V
25
30
0
5
10
15
20
25
30
FREQUENCY (GHz)
FREQUENCY (GHz)
Insertion Loss vs. Vbwctl, Vfctl = 7V
0 -2 Vbwctl=4V Vbwctl=7V Vbwctl=10V
Return Loss vs. Vbwctl, Vfctl = 7V
0 -5
INSERTION LOSS (dB)
-4 -6 -8 -10 -12 -14 -16 -18 -20 3 4
RETURN LOSS (dB)
Vbwctl=4V
-10
Vbwctl=7V
-15
Vbwctl=10V
-20 S11 S22
-25
-30 5 6 7 8 9 3 4 5 6 7 8 9
FREQUENCY (GHz)
FREQUENCY (GHz)
Center Frequency vs. Temperature, Vfctl = Vbwctl
9
Insertion Loss vs. Temperature, Vfctl = Vbwctl
0 -2 +25C +85C -40C
CENTER FREQUENCY (GHz)
8
INSERTION LOSS (dB)
8 10 12 14
7
+25C +85C -40C
-4 -6 -8 -10 -12 -14 -16
6
5
4
3 0 2 4 6
0
2
4
6
8
10
12
14
Vfctl (V)
Vfctl (V)
3-3
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC892LP5E
v00.0910
FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz
3 dB Bandwidth vs. Temperature, Vfctl = Vbwctl
12 +25C +85C -40C 11
Maximum Return Loss in a 2 dB Bandwidth vs. Temperature, Vfctl = Vbwctl
0 +25C +85C -40C -2
3
FILTERS - TUNABLE - SMT
3-4
RETURN LOSS (dB)
BANDWIDTH (%)
10
-4
9
-6
8
-8
7
-10
6 0 2 4 6 8 10 12 14
-12 0 2 4 6 8 10 12 14
Vfctl (V)
Vfctl (V)
Low Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1]
1
High Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1]
1.3 +25C +85C -40C 1.25
F20dB TO Fcenter RATIO
0.95
+25C +85C -40C
F20dB To Fcenter RATIO
10 12 14
1.2
0.9
1.15
1.1
0.85
1.05 0.8 0 2 4 6 8
1
Vfctl (V)
0
2
4
6
8
10
12
14
Vfctl (V)
Tuning Sensitivity vs. Temperature, Vfctl = Vbwctl
600 500
Group Delay
2.5 0V
SENSITIVITY (MHz/V)
2 GROUP DELAY (ns)
400
1.5
7V 14V
300 +25C +85C -40C
1
200
100
0.5
0 0 2 4 6 8 10 12 14
0 2 3 4 5 6 7 FREQUENCY (GHz) 8 9 10
Vfctl (V)
[1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to center
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC892LP5E
v00.0910
FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz
3
FILTERS - TUNABLE - SMT
3 dB Bandwidth vs. Bandwidth Control
18 16 14 12 10 8 6 4 2 0 2 4 6 8 10 12 14 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V
Insertion Loss vs. Bandwidth Control
0
INSERTION LOSS (dB)
BANDWIDTH (%)
-5
-10
-15
Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V
-20 0 2 4 6 8 10 12 14
Vfctl (V)
Vfctl (V)
Low Side Rejection Ratio vs. Bandwidth Control [1]
1 0.95
High Side Rejection Ratio vs. Bandwidth Control [1]
1.3 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V 1.25
F20dB TO Fcenter RATIO
0.9
F20dB TO Fcenter RATIO
12 14
1.2
0.85
1.15
0.8 Vbwctl=Vfctl Vbwctl=Vfctl +3V Vbwctl=Vfctl -3V
1.1
0.75
1.05
0.7 0 2 4 6 8 10
1 0 2 4 6 8 10 12 14
Vfctl (V)
Vfctl (V)
Maximum Return Loss in a 2 dB Bandwidth vs. Bandwidth Control
0 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V -2
Input IP3 vs. Power Input Vfctl = Vbwctl
35
30
RETURN LOSS (dB)
-4
-6
IP3 (dBm)
25
20
-8 15
-10
Pin = 0 Pin = 5 Pin = 10 Pin = 15 Pin = 20
-12 0 2 4 6 8 10 12 14
10 3.5 4.5 5.5 6.5 7.5 8.5
Vfctl (V)
FREQUENCY (GHz)
[1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to center
3-5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC892LP5E
v00.0910
FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz
Residual Phase Noise Vfctl = Vbwctl
-120
Absolute Maximum Ratings
Frequency Control Voltage (Vfctl)
0.5V 5.8V 13.0V
3
FILTERS - TUNABLE - SMT
3-6
RESIDUAL PHASE NOISE (dBc/Hz)
-0.5 to +15V -0.5 to +15V 26 dBm -65 to +150 C Class 1B
Bandwidth Control Voltage (Vbwctl) RF Power Input Storage Temperature ESD Rating (HBM)
-130
-140
-150
-160
ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS
1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
-170 1.0e+2
Reliability Information
Junction Temperature to Maintain 1 Million Hour MTTF Nominal Junction Temperature (T= 85 C and Pin = 10 dBm) Operating Temperature 150 C 90 C -40 to +85 C
OFFSET FREQUENCY (Hz)
Outline Drawing
Package Information
Part Number HMC892LP5E Package Body Material
NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. Pin BURR LENGTH SHALL BE 0.15mm MAXIMUM. Pin BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN.
Lead Finish 100% matte Sn
MSL Rating MSL1
[2]
Package Marking [1] H892 XXXX
RoHS-compliant Low Stress Injection Molded Plastic
[1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 C
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC892LP5E
v00.0910
FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz
3
FILTERS - TUNABLE - SMT
Pin Descriptions
Pin Number 1 - 4, 7 - 11, 13 15 - 18, 21 - 32 5, 20 Function N/C Description The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. These pins and exposed paddle must be connected to RF/DC ground. Interface Schematic
GND
6
RFIN
This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin.
12
Vfctl
Center frequency control voltage.
14
Vbwctl
Bandwidth control voltage.
19
RFOUT
This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin.
Application Circuit
3-7
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC892LP5E
v00.0910
FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz
Evaluation PCB
3
FILTERS - TUNABLE - SMT
List of Materials for Evaluation PCB 128531 [1]
Item J1, J2 J3, J4 C1, C2 U1 PCB [2] Description SMA - SRI SMA - Johnson 100 pF Capacitor, 0402 Pkg. HMC892LP5E Filter 127338 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 25FR
The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohms impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
3-8

▲Up To Search▲

Price & Availability of HMC892LP5E

	To Download HMC892LP5E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .