View G150XG03_133718.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
Specification
G150XG03
Version June 2006
Note: This specification is subject to change without prior notice
Data Modul AG - www.data-modul.com
Document version: 0.2 Date 1/27/2006
Product Specification 15.0" XGA Color TFT-LCD Module Model Name: G150XG03 V.0
www..com
(
) Preliminary Specifications ( ) Final Specifications
Note: This Specification is subject to change without notice.
Data Modul AG - www.data-modul.com
2
Record of Revision
Version and Date 0.0 2005/012/22 0.1 2006/1/20 Page All 5 6
www..com
Old description First Edition for Customer
New Description
Remark
Only define white luminance and power Add white luminance and power consumption @ 8mA IRCFL consumption @ 6.5mA IRCFL Only define white luminance @ 8mA IRCFL Add white luminance @ 6.5mA IRCFL
15 15
Only define power consumption @ 8mA Add power consumption @ 6.5mA IRCFL IRCFL Only define lamp life time@ 8mA IRCFL N/A Add the lamp life time @ 6.5mA IRCFL Add an addressing of PSWG model
0.2 2006/1/27
5
Data Modul AG - www.data-modul.com
3
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. www..com 8) Do not press or pat the panel surface by fingers,hand or tooling. 9) Do not press the reflector sheet at the back of the module to any directions. 10) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL reflector edge softly. Otherwise the TFT module may be damaged. 11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT module. 12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged.
Data Modul AG - www.data-modul.com
4
2.0 General Description
This specification applies to the 15.0 inch Color TFT/LCD Module G150XG03 V0. This module is designed for a display unit of personal computer. The display supports the XGA (1024 (H) x 768(V)) screen format and 16.2M colors (RGB 6-bits + FRC data)/262K (RGB 6-bit) selectable All input signals are 1 Channel LVDS interface compatible. This module does not contain an inverter card for backlight.
All the design rules of this module can correspond to PSWG standard.
www..com
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 ITEMS Screen Diagonal Active Area Pixels H x V Pixel Pitch Pixel Arrangement Display Mode White Luminance Contrast Ratio Optical Rise Time/Fall Time Color Saturation Nominal Input Voltage VDD Power Consumption (VDD line + CCFL line) Weight Physical Size Unit [mm] [mm] [mm] condition:
[cd/m 2] [msec] [Volt] [Watt] [Grams] [mm]
Electrical Interface Support Color Temperature Range Operating Storage (Shipping) Surface Treatment ROHS [oC] [oC]
SPECIFICATIONS 381 (15 ") 304.128 (H) x 228.096 1024(x3) x 768 0.297 (per one triad) x 0.297 R.G.B. Vertical Stripe TN mode, Normally White 250 (Typ) @ 8mA; 200nit(Typ) @ 6.5mA 500 : 1 (Typ) 12 (Typ) (Note 1) 65% NTSC (Typ) +3.3 V 13.3 W (Typ.) @8mA (Gray Bar Pattern); 11.3 W (Typ.) @6.5mA (Gray Bar Pattern) 1100 (Typ) Min. Typ. Max. Horizatal(H) 326.0 326.5 327.0 Vertical(V) 253.0 253.5 254.0 Depth(D) 12.0 1 Channel LVDS 16.2M colors (RGB 6-bit + FRC data)/262k(RGB 6-bit) selectable 0 to +50 -20 to +60 Hard-coating (3H), anti-glare treatment RoHS Compliance
Note 1 :System should warm up for at least one hour
Data Modul AG - www.data-modul.com
5
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25 Item Unit Conditions Horizontal CR = 10 Vertical CR = 10 Horizontal CR = 5 Vertical CR = 5 Contrast ratio
www..com
(Room Temperature): Max. Typ. Min. 60 60 55 45 65 65 65 65 400 0.612 0.307 0.276 0.551 0.114 0.071 0.283 0.299 200 180 75 70 70 65 55 75 75 75 75 500 8.5 3.5 12 0.642 0.337 0.306 0.581 0.144 0.101 0.313 0.329 250 200 80 1.2 1.5 -20 -
Note keep total 120(Mayb e 60,60)
(Right) (Left) (Up) (Down) (Right) (Left) (Up) (Down)
Viewing Angle
[degree]
11 5 0.672 0.367 0.336 0.611 0.174 0.131 0.343 0.359 Note 1 -
Normal Direction Rising Time [msec] Falling Time Rising + Falling Red x Red y
Response Time
Color / Chromaticity Coordinates (CIE)
Green x Green y Blue x Blue y
Color White
Coordinates
(CIE)
White x White y [cd/m 2] [cd/m 2] [%] [%] dB
White Luminance @ CCFL 8mA (center) White Luminance @ CCFL 6.5mA (center) Luminance Uniformity Crosstalk (in 75Hz) Flicker
Note 2 Note 3 Note 4
Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A , BM 7 ,CS-1000, CA210, SR_3 & EZ Contrast(ELDIM)* ) Aperture Test Point Environment 1 with 50cm viewing distance
Center (VESA point 9) < 1 lux
LCD Module
measuring distance
Module Driving Equipment
PR-880 / BM5A / BM7
Data Modul AG - www.data-modul.com
6
*' EZ Contrast is different measurement tool with very close viewing distance.
www..com
Data Modul AG - www.data-modul.com
7
Note 1: Definition of Response time The output signals of photo detector are measured when the input signals are changed from "Full Black" to "Full White" (rising time), and from "Full White" to "Full Black "(falling time), respectively. The response time is interval between the 10% and 90% of amplitudes.
%
Tr F
Tr R
100 90 Optical response
www..com
White 10 0
Black
White
Note 2: Brightness uniformity of these 9 points is defined as below 90 % 50 % 10 % 10 %
50 %
90 %
Uniformity =
Minimum Luminance in 9 points (1 - 9) x 100% Maximum Luminance in 9 Points (1 - 9)
Data Modul AG - www.data-modul.com
8
Note 3: Crosstalk is defined as below : 1/2 1/6 1/6 2/3 1/2 1/3 1/6
A
A'
1/6 1/3 1/2 B' 2/3
1/2 B 184 gray level 184 gray level
Unit: percentage of dimension of display area
0 gray level l LA-LA' l / LA x 100%= 1.5% max., L A and LB are brightness at location A and B
l LB www..com -LB' l / LB x 100%= 1.5% max., L A' and L B' are brightness at location A ' and B'
Note 4: Test Paterm: Subchecker Pattern at 127 gray level
30mm
CA210 FFT Sub Checker Pattern
A0
A30
RGB RGB Gray Level = L127 RGB RGB Gray Level = L0
RGB RGB
Data Modul AG - www.data-modul.com
9
Amplitude
AC
DC Time
www..com
Flicker (dB) = 20 log
AC Level(at 30 Hz) DC Level
Data Modul AG - www.data-modul.com
10
3.0 Functional Block Diagram
The following diagram shows the functional block of the 15.0 inches wide Color TFT/LCD Module:
AU ASIC
Timing Controller
G1
LVDS
LVDS RSDS G768 D1
TFT-LCD 1024(3)*768 Pixels
Connector
+ 3.3V
www..com
D3072 2 CCFL
DC/DC Converter
Gamma Correction
DC POWER
Inverter
CWY20G - A0G16 / MSB240420 Mating Type: HRS DF14-20S-1.25C
JST-BHR-03VS-1 SM02(8.0)B-BHS-1-TB
Data Modul AG - www.data-modul.com
11
4.0 Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:
4.1 TFT LCD Module
Item Logic/LCD Drive Symbol VDD Min 0.3 Max +3.6 Unit [Volt] Conditions Note 1,2
4.2 Backlight Unit
Item CCFL Current
www..com
Symbol IRCFL
Min -
Max 8.5
Unit [mA] rms
Conditions Note 1,2
4.3 Absolute Ratings of Environment
Item Operating Temperature Operating Humidity Storage Temperature Storage Humidity Note 1: With in Ta (25 ) Symbol TOP HOP TST HST Min 0 8 -20 8 Max +50 90 +60 90 Unit [ oC] [%RH] [ C] [%RH]
o
Conditions Note 3 Note 3 Note 3 Note 3
Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard) . Please refer the graph below for the corresponding of temperature and humidity."
Data Modul AG - www.data-modul.com
12
5.0 Electrical characteristics
5.1 TFT LCD Module 5.1.1 Power Specification
Input power specifications are as follows; Symbol VDD IDD Irush PDD www..com VDDrp Parameter Logic/LCD Drive Voltage VDD current LCD Inrush Current VDD Power Allowable Logic/LCD Drive Ripple Voltage Min 3.0 Typ 3.3 600 2.0 Max 3.6 700 3 2.3 100 Units [Volt] [mA] [A] [Watt] [mV] p-p 10% Vin=3.3V , Gray Bar Pattern, at 60Hz Note Vin=3.3V , Gray Bar Pattern, at 60Hz Vin=3.3V , All Black Pattern, at 75Hz Condition
Note: Measurement conditions:
+5.0V +3.3V D6 D5 D2 D1 R1 47K
Q3 AO6402 F1 S VCC
G
(LCD Module Input)
C1 1uF/16V
(High to Low) Control Signal
SW
D1 D2 D5 D6 R2 G 1K C3 Q3 AO6402 VR1 47K 0.01uF/25V S
+12.0V
C2 1uF/25V
90%
3.3V
10% 0V 470 us
Vin rising time
Data Modul AG - www.data-modul.com
13
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when Vin is off It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail. Each signal characteristics are as follows; Symbol VTH VTL VID VICM Parameter Differential Input High Threshold Differential Input Low Threshold Input Differential Voltage Differential Input Common Mode Voltage Min -100 100 1.1 Typ 400 Max 100 600 1.45 Units [mV] [mV] [mV] [V] VTH/VTL = 100mV Condition VICM = 1.2V VICM = 1.2V Note Note Note Note
www..com
Note: LVDS Signal Waveform
VTH VID VTL
VICM
VSS
Data Modul AG - www.data-modul.com
14
5.2 Backlight Unit
Parameter guideline for CCFL Inverter Symbol IRCFL ICFL FCFL ViCFL (0oC)
www..com
Parameter CCFL operation range CCFL Inrush current CCFL Frequency CCFL Ignition Voltage
Min. 2.5 40
Typ. 8 55
Max. 8.5 20 80
Unit [mA] rms [mA] [KHz] [Volt]
Condition (Ta=25oC) Note 4
(Ta=25oC) Note 1
1450
-
rms
(Ta=0oC) Note 3
(reference) ViCFL (25oC) (reference) CCFL Discharge Voltage VCFL (Only for reference) CCFL Power consumption @8mA(excluding inverter) PCFL CCFL Power consumption 8 @6.5mA(excluding inverter) Note 1: CCFL frequency should be carefully determined to avoid interference between inverter and TFT LCD. Note 2: Calculator value for reference (IRCFLxVCFLx2=PCFL). Note 3: CCFL inverter should be able to give output a voltage more than 1450 volt. Lamp units need 1450 volt minimum for ignition. Note 4: CCFL life time is 30,000hr at 8.0mA and 50000hr at 6.5mA. It 's defined as when the brightness is reduced by half. It's recommended not to exceed 8.0mA for CCFL life time concern and it 's prohibited to exceed 8.5mA for safety concern. 9 [Watt] 10 11 (Ta=25 oC) Note 2 (@8mA) (@2.5mA) rms 620 710 [Volt] (Ta=25 oC) Note 2 CCFL Ignition Voltage 1100 rms [Volt] (Ta=25 oC) Note 3
Data Modul AG - www.data-modul.com
15
6.0 Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
www..com
Data Modul AG - www.data-modul.com
16
6.2 The input data format
www..com
Note1: Please follow PSWG. Note2: 8-bit in Note3: R/G/B data 7:MSB, R/G/B data 0:LSB
Data Modul AG - www.data-modul.com
17
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible . The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.
CWY20G-A0D1T (PTWO) or MSB240420 (STM) Pin No. Symbol 1 2 3 4
www..com
Description Power Supply, 3.3V (typical) Power Supply, 3.3V (typical) Ground Ground - LVDS differential data input (R0-R5, G0) + LVDS differential data input (R0-R5, G0) Ground - LVDS differential data input (G1-G5, B0-B1) + LVDS differential data input (G1-G5, B0-B1) Ground - LVDS differential data input (B2-B5, HS, VS, DE) + LVDS differential data input (B2-B5, HS, VS, DE) Ground - LVDS differential clock input + LVDS differential clock input Ground - LVDS differential data input (R6-R7, G6-G7,B6-B7) - LVDS differential data input (R6-R7, G6-G7,B6-B7) Ground Selection for 6 bits/8bits LVDS data input *Note1
VDD VDD VSS VSS Rin0Rin0+ VSS Rin1Rin1+ VSS Rin2Rin2+ VSS ClkINClkIN+ VSS Rin3Rin3+ VSS SEL68
5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20
Note 1: SEL68= High or NC , accept 6 bits LVDS data input; SEL68= Low , accept 8 bits LVDS data input.
Data Modul AG - www.data-modul.com
18
6.4 Interface Timing 6.4.1 Timing Characteristics
Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.
Signal Clock Timing Hsync Timing
Vsync Timing
Parameter Clock frequency Horizontal active Horizontal blanking Horizontal period Vertical active Vertical blanking Vertical period
Symbol clk Thd Thbl Th Tvd Tvbl Tv
MIN 50 1024 30 1054 768 8 776
TYP 65 1024 320 1344 768 38 806
MAX 81 1024 1024 2048 768 256 1024
Unit MHz Tclk Tclk Tck Th Th Th
www..com
Note:DE mode only Note: Typical value refer to VESA STANDARD
Data Modul AG - www.data-modul.com
19
6.4.2 Timing diagram
www..com
Data Modul AG - www.data-modul.com
20
6.5 Power ON/OFF Sequence
Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when Vin is off.
1sec min. Vin 0V
www..com
10%
90% 10ms max.
90% 10% 10% 0 min.
Signal 0V Lamp On 0V
0 min. 10% 10%
200ms
Data Modul AG - www.data-modul.com
21
7.0 Connector & Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components.
7.1 TFT LCD Module
Connector Name / Designation Manufacturer Type Part Number Mating Housing Part Number www..com Pin# 1 3 5 7 9 11 13 15 17 19 Signal Name VDD VSS Rin0VSS Rin1+ Rin2VSS ClkIN+ Rin3VSS 2 4 6 8 10 12 14 16 18 20 Interface Connector / Interface card P-TWO or compatible
CWY20G - A0G16 / MSB240420
HRS DF14-20S-1.25C Pin# Signal Name VDD VSS Rin0+ Rin1VSS Rin2+ ClkINVSS Rin3+ SEL68
Data Modul AG - www.data-modul.com
22
7.1.1 Connector Illustration
www..com
Data Modul AG - www.data-modul.com
23
7.2 Backlight Unit
Connector Name / Designation Manufacturer Type / Part Number Mating Type / Part Number For Lamp Connector JST or compatible BHR-03VS-1 SM02(8.0)B-BHS-1-TB
7.3 Signal for Lamp connector
www..com
Pin Symbol 1 2 3 HV NC LV Cable length: 140 +- 5 mm
Description Lamp High Voltage No connection Ground
Connector-output position: right side (front view) Lamp assembly design shall be easy for replacement and repair.
Data Modul AG - www.data-modul.com
24
8.0 Reliability
Reliability test condition
No Test Item 1 2 3 4 5 6 7 8 9 Temperature Humidity Bias (THB) High Temperature Operation (HTO) Low Temperature Operation (LTO) High Temperature Storage (HTS) Low Temperature Storage (LTS) Thermal Shock Test (TST) On/Off Test Shock Test (Non-Operating) Vibration Test (Non-Operating) Test Condition 50 50 0 60 -20 -20 , 80%, 300hours , 300hours , 300hours , 300hours , 300hours /30min, 60 /30min, 100 cycles
On/10sec, Off/10sec, 30,000 cycles 50G, 20ms, Half-sine wave (+ X, +Y, +Z) 1.5G(10~200Hz P- P), 30 Minutes each Axis (X, Y, Z) Contact Discharge: 8KV, 150pF(330 ) 1sec, 8 points, 25 times/ point Air Discharge: 15KV, 150pF(330 ) 1sec, 8 points, 25 times/ point
www..com
10 ESD (ElectroStatic Discharge)
11 Altitude Test
Operation:10,000 ft Non-Operation:30,000 ft
12 Drop Test
The drop height is 60cm
Data Modul AG - www.data-modul.com
25
9.0 Shipping and packing 9-1 Shipping label format
www..com
9-2 Carton package
Data Modul AG - www.data-modul.com
26
10.0 Safety
10.1 Sharp Edge Requirements
There will be no sharp edges or comers on the display assembly that could cause injury.
10.2 Materials 10.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO Toxicologist.
10.2.2 Flammability
All components including electrical components that do not meet the flammability grade
www..com UL94-V1 in the module will complete the flammability rating exception approval process.
The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board.
10.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.
11.0 Other requirement
11.1 National Test Lab Requirement
The display module will satisfy all requirements for compliance to UL 1950, First Edition CSA C22.2 No.950-M89 EEC 950 EN 60 950 U.S.A. Information Technology Equipment Canada, Information Technology Equipment International, Information Technology Equipment International, Information Processing Equipment (European Norm for IEC950)
Data Modul AG - www.data-modul.com
27
www..com
12.0 Mechanical Characteristics
Data Modul AG - www.data-modul.com
28
www..com
Data Modul AG - www.data-modul.com
29
www..com
Data Modul AG - www.data-modul.com
30
Data Modul Headquarters Munich Landsberger-Str. 322 D-80687 Munich - Germany Tel.: +49-89-56017-0
Sales Office Duesseldorf Fritz-Vomfelde-Str. 8 D-40547 Duesseldorf - Germany Tel.: +49-211-52709-0
www..com
Sales Office Hamburg Borsteler Chaussee 51 D-22453 Hamburg - Germany Tel.: +49-40-42947377 - 0
Sales Office Stuttgart Friedrich-List-Str. 42 D-70771 Leinfelden-Echterdingen Germany Tel.: +49-711-782385-0 Data Modul France, S.A.R.L. Bat B - Hall 204 1-3 Rue des Campanules 77185 Lognes - France Tel.: +33-1-60378100 Data Modul Italia, S.r.l. Regus Center Senigallia Via Senigallia 18/2 20161 Milano - Italy Tel.: +39-02-64672-509 Data Modul Iberia, S.L. c/ Adolfo Perez Esquivel 3 Edificio Las Americas III Oficiana 40 28230 Parque Empresarial Madrid Las Rozas - Spain Tel.: +34-916 366 458 Data Modul Ltd. / UK 3 Brindley Place Birmingham B 12JB United Kingdom Tel.: +44-121-698-8641 Data Modul Inc. / USA 1767-46 Veterans Memorial Highway Islandia NY 11749 USA Tel.: +1-877-951-0800
www.data-modul.com display@data-modul.com

▲Up To Search▲

Price & Availability of G150XG03

	To Download G150XG03 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .