 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| A Product Line of Diodes Incorporated ZABG4002 LOW POWER 4 STAGE FET LNA BIAS CONTROLLER Summary The ZABG4002 is a four stage depletion mode FET bias controller intended primarily for satellite Low Noise Block's (LNB's), but its also suitable for other LNA applications such as those in found in PMR's and microwave links. The ZABG4002 provides each FET with an independent protected negative gate voltage and positive drain voltage with user programmable drain current. Combining an advanced IC process and packaging techniques, the ZABG4002 helps minimise power consumption, component cost and PCB area whilst enhancing overall reliability. Features NEW PRODUCT * * * * * * * * * * * Four stage FET bias controller Operating range of 3.0V to 8.0V Low quiescent supply current, 1.2mA typical FET drain voltages set at 2.0V FET drain current selectable from 0 to 15mA Switchable FETs for power management Allows first and second stage FETs to be run at different (optimum) drain currents FET drain voltages and currents held stable over temperature and Vcc variations FETs protected against overstress during power-up and power-down. Internal negative supply generator allowing single supply operation (available for external use) Low external component count Pin Assignments D1 VCC G1 D3 G3 D4 G4 RCAL1 CSUB CNB1 RCAL2 CNB2 D2 G2 VCC GND Top View CSUB Bottom View Applications * * * * Twin LNB's US LNB's Microwave links PMR and Cellular telephone systems www..com * Quad LNB's Single Universal LNB System Diagram Vertical Gain stages GaAs FET's Down Converter IF Switching, gain and control Horizontal ZABG 4002 6002 ZXHF 5002 ZABG4002 Document number: DS32047 Rev. 1 - 2 1 of 7 www.diodes.com January 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZABG4002 Device Description The ZABG series of devices are designed to meet the bias requirements of GaAs and HEMT FETs commonly used in satellite receiver LNBs with a minimum of external components whilst operating from a minimal voltage supply and using minimal current. The ZABG4002 provides four FET bias stages, arranged in two pairs of two. Resistors connected to pins Rcal1 and Rcal2 set the FET drain currents of each pair over the range of 0 to 15mA, allowing input FETs to be biased for optimum noise and amplifier FETs for optimum gain. Drain voltages of all stages are set at 2.0V. The drain supplies are current limited to approximately 5% above the operating currents set by the Rcal resistors. As an additional feature the Rcal pins can also be used as logic inputs to disable pairs of FETs as part of a power management scheme or simply an alternative to LNA switching. Driven to a logic high (>3.0V), the inputs disable their associated FET bias stages by switching gate feeds to 2.5V and drain feeds open circuit. Depletion mode FETs require a negative voltage bias supply when operated in grounded source circuits. The ZABG4002 includes an integrated low noise switched capacitor DC-DC converter generating a regulated output of -2.5V to allow single supply operation. To facilitate the design of efficient low voltage 3.3V LNB systems and to maintain compatibility with higher voltage legacy designs, the ZABG4002 is capable of operating within the supply of 3.0V to 8V. These devices are unconditionally stable over the full working temperature with the FETs in place, subject to the inclusion of the recommended gate and drain capacitors. These ensure RF stability and minimal injected noise. It is possible to use less than the devices full complement of FET bias controls, unused drain and gate connections can be left open circuit without affecting operation of the remaining bias circuits. To protect the external FETs the circuits have been designed to ensure that, under any conditions including power up/down transients, the gate drive from the bias circuits cannot exceed -3V. Additionally each stage has its own individual current limiter. Furthermore if the negative rail experiences a fault condition, such as overload or short circuit, the drain supply to the FETs will shut down avoiding excessive current flow. To minimise PCB space ZABG4002 is packaged in the 16 pin 3mm x 3mm QFN package. Device operating temperature is -40C to 85C to suit a wide range of environmental conditions. NEW PRODUCT www..com ZABG4002 Document number: DS32047 Rev. 1 - 2 2 of 7 www.diodes.com January 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZABG4002 Maximum Ratings Parameter Supply Voltage Supply Current Power Dissipation Operating Temperature Range Storage Temperature Range Rating -0.6 to +10 80 500 -40 to +85 -40 to +150 Unit V mA mW C C NEW PRODUCT Electrical Characteristics Parameter Operating Voltage Range (note 1) Supply Current Substrate Voltage Oscillator Frequency Gate Characteristics Gate (G1 to G4) Current Range Voltage Low Voltage High Voltage Disabled (Measured at TAMB = 25C, VCC = 3.3V (note 1), RCAL1 = RCAL2 = 39k (setting ID to 10mA) unless otherwise stated) Conditions Symbol VCC Min. 3.0 Typ. Max. 8.0 Unit V mA mA V V kHz ID1 = ID2 = ID3 = ID4 = 0 ID1 = ID2 = ID3 = ID4 = 10mA ICSUB = 0 ICSUB = -200uA ICC ICC(L) VCSUB VCSUB(L) FOSC -3.0 150 1.2 42 -2.65 -2.55 240 4.0 44 -2.0 -2.0 600 ID = 12mA, IG = -10uA ID = 8mA, IG = 0 ID = 0, IG = -10uA, V RCAL = 3.0V IG VG(L) VG(H) VG(DIS) -100 -3.0 0 -3.0 -2.5 0.7 -2.5 +500 -2.0 1.0 -2.0 uA V V V Drain Characteristics Drain (D1 to D4) Current Range Current Operating www..com Current Disabled Voltage Operating delta ID vs VCC delta ID vs TOP delta VD vs VCC delta VD vs TOP RCAL(1 and 2) Disable Threshold Input Current Output Noise Drain Voltage Gate Voltage Notes: Standard Application Circuit VD = 0, VRCAL = 3.0V ID = 10mA VCC = 3.3 to 8.0V TOP = -40C to +85C VCC = 3.3 to 8.0V TOP = -40C to +85C ID ID(OP) ID(DIS) VD(OP) dID/dVCC dID/dTOP dVD/dVCC dVD/dTOP VRCAL(DIS) IRCAL(DIS) 0 8 1.8 10 2.0 1.2 0.05 0.05 50 2.7 1.7 15 12 10 2.2 mA mA uA V %/V %/C %/V ppm/C V uA 1.8 VRCAL = 3.0V 3.0 10 CGATE-GND = 10nF, CDRAIN-GND = 10nF CGATE-GND = 10nF, CDRAIN-GND = 10nF VD(NOISE) VG(NOISE) 0.02 0.005 Vpk-pk Vpk-pk 1. The two Vcc pins are internally connected, only one of the pins needs to be powered for the device to function. See applications section for further information. 2. ESD sensitive, handling precautions are recommended. 3. The negative bias voltages are generated on-chip using an internal oscillator. Two external capacitors, CNB and CSUB of value 47nF are required for this purpose. 4. The package (QFN1633) exposed pad must either be connected to Csub or left open circuit. 5. The characteristics are measured using two external reference resistors RCAL1 and RCAL2 of value 39k , wired from pins RCAL1/2 to ground. Resistor RCAL1 sets the drain current of FETs 1 and 3, resistor RCAL2 sets the drain currents of FETs 2 and 4. 6. Noise voltage measurements are made with FETs and gate and drain capacitors of value 10nF in place. Noise voltages are not measured in production. ZABG4002 Document number: DS32047 Rev. 1 - 2 3 of 7 www.diodes.com January 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZABG4002 Typical Characteristics (Measured at TAMB = 25C, VCC = 3.3V, RCAL1 = RCAL2 = 39k (setting ID to 10mA) unless otherwise stated) ZABG4002 Drain Voltage vs Drain Current 2.2 ZABG4002 Drain Current vs RCAL 15 2.1 D rain C u rren t (m A ) NEW PRODUCT D rain V o ltag e (V ) 10 100 1000 10 2 5 1.9 0 1.8 0 5 10 15 RCAL (k) Drain Current (mA) ZABG4002 Drain Drain Current vs Temperature 20 18 2.2 2.3 ZABG4002 Drain Voltage vs Temperature 16 14 D rain C u rren t (m A ) 12 10 8 6 4 D rain V oltage (V ) 2.1 2 1.9 1.8 www..com 2 0 -40 -20 0 20 40 60 80 1.7 -40 -20 0 20 40 60 80 Temperature (C) Temperature (C) ZABG4002 Substrate Voltage vs Substrate Current -2 -2.2 S u b strate V o ltag e (V ) -2.4 -2.6 -2.8 -3 0 50 100 150 200 250 Substrate Current (uA) ZABG4002 Document number: DS32047 Rev. 1 - 2 4 of 7 www.diodes.com January 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZABG4002 Applications Circuit L* Vcc Vcc G1 D1 D3 G3 D4 G4 Rcal1 Rcal2 C* C1 10nF D2 G2 JF1 NEW PRODUCT L* Vcc Gnd ZABG4002 CNB 47nF CSUB 47nF Csub Cnb1 Cnb2 C* C2 10nF RCAL2 39k RCAL1 39k * Stripline Elements Applications Information Above is a partial applications circuit for the ZABG4002 showing all external components needed for biasing one of the four FET stages available. Each bias stage is provided with a gate and drain pin. The drain pin provides a regulated 2.0V supply that includes a drain current monitor. The drain current taken by the external FET is compared with a user selected level, generating a signal that adjusts the gate voltage of the FET to obtain the required drain current. If for any reason, an attempt is made to draw more than the user set drain current from the drain pin, the drain voltage will be reduced to ensure excess current is not taken. The gate pin drivers are also current limited. www..com are split up into two pairs, with the drain current of each pair set by an external R The bias stages CAL resistor. RCAL1 sets the drain currents of stages 1 and 3, whilst RCAL2 sets the drain currents of stages 2 and 4. This allows the optimisation of drain currents for differing tasks such as input stages where noise can be critical and later amplifier stages where gain may be more important. A graph showing the relationship between the value of RCAL and ID is provided in the Typical Characteristics section of this datasheet. The RCAL pins can also be used as logic inputs. If set to a logic high state (>3.0V), the associated FET bias stages are disabled, driving gate pins to -2.5V and switching drain pins open-circuit. This feature can be used as part of a power management system that turns off any unwanted stages in a multi input receiver. The ZABG4002 includes a switched capacitor DC-DC converter that is used to generate the negative supply required to bias depletion mode FETs used in common source circuit configuration as shown above. This converter uses two external capacitors, CNB the charge transfer capacitor and CSUB the output reservoir capacitor. The circuit provides a regulated -2.5V supply both for gate driver use and for external use if required (for extra discrete bias stages, mixer bias, local oscillator bias etc.). The -2.5V supply is available from the CSUB pin. If any bias stages are not required, their gate and drain pins may be left open circuit. If all bias stages associated with an RCAL resistor are not required, then this resistor may be omitted. To ease PCB layout, the pinout for the ZABG4002 includes two Vcc pins. These pins are internally connected so only one of the pins needs to be powered for the device to function. It is probable that the extra pin will help avoid the need for trace cross-over components or ground plane disruption from reverse side PCB links. Note that the exposed pad of the package must be either left floating or connected to Csub. ZABG4002 Document number: DS32047 Rev. 1 - 2 5 of 7 www.diodes.com January 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZABG4002 Package Outline Dimensions E A1 D A3 Pin #1 ID E2 L A NEW PRODUCT e b Z D2 QFN16 3x3 Dim Min Max A 0.55 0.65 A1 0.00 0.05 A3 0.15 Typ b 0.18 0.28 D 2.95 3.05 D2 1.40 1.60 e 0.50 BSC E 2.95 3.05 E2 1.40 1.60 L 0.35 0.45 Z 0.625 Typ All Dimensions in mm Note: Controlling dimensions are in millimetres. Approximate dimensions are provided in inches. The package appearance may vary as shown, for further details please contact your local Diodes sales office. Ordering Information Device ZABG4002JA16TC (Note x) Package QFN1633 Reel Size (inches) 18 Tape Width (mm) 8 Quantity (per reel) 3000 Marking Information www..com Pin 1 ZABG 4002 YYWW Part Name Date Code Year/Week ZABG4002 Document number: DS32047 Rev. 1 - 2 6 of 7 www.diodes.com January 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZABG4002 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. NEW PRODUCT Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related www..com information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright (c) 2009, Diodes Incorporated www.diodes.com ZABG4002 Document number: DS32047 Rev. 1 - 2 7 of 7 www.diodes.com January 2010 (c) Diodes Incorporated |
Price & Availability of ZABG4002
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |