View A63L7332_307658.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

A63L7332 Series
128K X 32 Bit Synchronous High Speed SRAM with Burst Counter and Pipelined Data Output
Preliminary
Document Title
128K X 32 Bit Synchronous High Speed SRAM with Burst Counter and Pipelined Data Output Revision History
Rev. No.
0.0 1.0 1.1
History
Initial issue Change fast access times from 4.5/5 ns to 4.2/4.5/5.0 ns Change DC and operating characteristics ICC1 (Max.) : 300mA to 350mA ISB1 (Max.) : 25mA to 38mA
Issue Date
June 02, 1998 August 27, 1998 December 18, 1998
Remark
Preliminary
1.2
Modify 100-pin LQFP symbol y dimensions Max. in mm :0.08 0.1 Max. in inches : 0.003 0.004
December 31, 1998
PRELIMINARY
(December, 1998, Version 1.2)
AMIC Technology, Inc.
A63L7332 Series
128K X 32 Bit Synchronous High Speed SRAM with Burst Counter and Pipelined Data Output
Preliminary
Features
n n n n n
Fast access times: 4.2/4.5/5.0 ns (143/133/100 MHZ) Single +3.3V+10% or +3.3V-5% power supply Synchronous burst function Individual Byte Write control and Global Write Registered output for pipelined applications
n Three separate chip enables allow wide range of options for CE control, address pipelining n Selectable BURST mode n SLEEP mode (ZZ pin) provided n Available in 100-pin LQFP package
General Description
The A63L7332 is a high-speed, low-power SRAM containing 4,194,304 bits of bit synchronous memory, organized as 131,072 words by 32 bits. The A63L7332 combines advanced synchronous peripheral circuitry, 2-bit burst control, input registers, output registers and a 128K X 32 SRAM core to provide a wide range of data RAM applications. The positive edge triggered single clock input (CLK) controls all synchronous inputs passing through the registers. Synchronous inputs include all addresses (A0 A16), all data inputs (I/O1 - I/O32), active LOW chip enable ( CE ), two additional chip enables (CE2, CE2 ), burst control inputs ( ADSC , ADSP , ADV ), byte write enables ( BWE , BW1 , BW2 , BW3 , BW4 ) and Global Write ( GW ). Asynchronous inputs include output enable ( OE ), clock (CLK), BURST mode (MODE) and SLEEP mode (ZZ). Burst operations can be initiated with either the address status processor ( ADSP ) or address status controller ( ADSC ) input pin. Subsequent burst sequence burst addresses can be internally generated by the A63L7332 and controlled by the burst advance ( ADV ) pin. Write cycles are internally self-timed and synchronous with the rising edge of the clock (CLK). This feature simplifies the write interface. Individual Byte enables allow individual bytes to be written. BW1 controls I/O1 - I/O8, BW2 controls I/O9 - I/O16, BW3 controls I/O17 - I/O24, and BW4 controls I/O25 - I/O32, all on the condition that BWE is LOW. GW LOW causes all bytes to be written.
PRELIMINARY
(December, 1998, Version 1.2)
1
AMIC Technology, Inc.
A63L7332 Series
Pin Configuration
ADSC
ADSP
BWE
GND
BW4
BW3
BW2
BW1
VCC
ADV
CE2
CE2
CLK
GW
OE
CE
A6
A7
A8 82
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
NC I/O17 I/O18 VCCQ GNDQ I/O19 I/O20 I/O21 I/O22 GNDQ VCCQ I/O23 I/O24 NC VCC NC GND I/O25 I/O26 VCCQ GNDQ I/O27 I/O28 I/O29 I/O30 GNDQ VCCQ I/O31 I/O32 NC
100
81
A9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
80 79 78 77 76 75 74 73 72 71 70 69 68 67
NC I/O16 I/O15 VCCQ GNDQ I/O14 I/O13 I/O12 I/O11 GNDQ VCCQ I/O10 I/O9 GND NC VCC ZZ I/O8 I/O7 VCCQ GNDQ I/O6 I/O5 I/O4 I/O3 GNDQ VCCQ I/O2 I/O1 NC
A63L7332
66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
GND
NC
NC
NC
MODE
NC
A5
A4
A3
A2
A1
A0
A10
A11
A12
A13
A14
A15
VCC
A16
PRELIMINARY
(December, 1998, Version 1.2)
2
AMIC Technology, Inc.
A63L7332 Series
Block Diagram
ZZ MODE MODE LOGIC
ADV
CLK
CLK LOGIC ADSC ADSP
BURST LOGIC ADDRESS COUNTER CLR
A0-A16
ADDRESS REGISTERS
17
8
BYTE1 WRITE DRIVER BYTE2 WRITE DRIVER BYTE3 WRITE DRIVER BYTE4 WRITE DRIVER
8
8 GW BWE BW1 BW2 BW3 BW4 BYTE WRITE ENABLE LOGIC 8
8
128KX8X4 MEMORY 32 OUTPUT REGISTERS ARRAY
8
8
8
32
4 DATA-IN REGISTERS 4 CE CE2 CE2 CHIP ENABLE LOGIC PIPELINED ENABLE LOGIC
OE I/O1 - I/O32
OUTPUT ENABLE LOGIC
PRELIMINARY
(December, 1998, Version 1.2)
3
AMIC Technology, Inc.
A63L7332 Series
Pin Description
Pin No. 32 - 37, 44 - 50, 81, 82, 99, 100 89 87, 93 - 96 88 86 92, 97, 98 83 84 85 31 Symbol A0 - A16 Address Inputs Description
CLK
BWE , BW1 - BW4 GW OE CE2 ,CE2, CE ADV ADSP ADSC
Clock Byte Write Enables Global Write Output Enable Chip Enables Burst Address Advance Processor Address Status Controller Address Status Burst Mode: HIGH or NC (Interleaved burst) LOW (Linear burst) Asynchronous Power-Down (Snooze): HIGH (Sleep) LOW or NC (Wake up) Data Inputs/Outputs
MODE
64
ZZ
2, 3, 6 - 9, 12, 13, 18, 19, 22 - 25, 28, 29, 52, 53, 56 - 59, 62, 63, 68, 69, 72 - 75, 78, 79 1, 14, 16, 30, 38, 39, 42, 43, 51, 66, 80 15, 41, 65, 91 17, 40, 67, 90 4, 11, 20, 27, 54, 61, 70, 77 5, 10, 21, 26, 55, 60, 71, 76
I/O1- I/O32
NC
No Connection
VCC GND VCCQ
Power Supply Ground Isolated Output Buffer Supply
GNDQ
Isolated Output Buffer Ground
PRELIMINARY
(December, 1998, Version 1.2)
4
AMIC Technology, Inc.
A63L7332 Series
Synchronous Truth Table (See Notes 1 Through 5)
Operation Deselected Cycle, Power-down Deselected Cycle, Power-down Deselected Cycle, Power-down Deselected Cycle, Power-down Deselected Cycle, Power-down READ Cycle, Begin Burst READ Cycle, Begin Burst WRITE Cycle, Begin Burst READ Cycle, Begin Burst READ Cycle, Begin Burst READ Cycle, Continue Burst READ Cycle, Continue Burst READ Cycle, Continue Burst READ Cycle, Continue Burst WRITE Cycle, Continue Burst WRITE Cycle, Continue Burst READ Cycle, Suspend Burst READ Cycle, Suspend Burst READ Cycle, Suspend Burst READ Cycle, Suspend Burst WRITE Cycle, Suspend Burst WRITE Cycle, Suspend Burst Address Used NONE NONE NONE NONE NONE External External External External External Next Next Next Next Next Next Current Current Current Current Current Current
CE
CE2
CE2 X L X L X H H H H H X X X X X X X X X X X X
ADSP
ADSC
ADV
WRITE
OE
CLK L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H
I/O Operation High-Z High-Z High-Z High-Z High-Z Dout High-Z Din Dout High-Z Dout High-Z Dout High-Z Din Din Dout High-Z Dout High-Z Din Din
H L L L L L L L L L X X H H X H X X H H X H
X X H X H L L L L L X X X X X X X X X X X X
X L L H H L L H H H H H X X H X H H X X H X
L X X L L X X L L L H H H H H H H H H H H H
X X X X X X X X X X L L L L L L H H H H H H
X X X X X X X L H H H H H H L L H H H H L L
X X X X X L H X L H L H L H X X L H L H X X
PRELIMINARY
(December, 1998, Version 1.2)
5
AMIC Technology, Inc.
A63L7332 Series
Notes: 1. X = "Disregard", H = Logic High, L = Logic Low. 2. WRITE = L means: 1) Any BWx ( BW1 , BW2 , BW3 , or BW4 ) and BWE are low or 2) GW is low. 3. All inputs except OE must be synchronized with setup and hold times around the rising edge (L-H) of CLK. 4. For write cycles that follow read cycles, OE must be HIGH before the input data request setup time and held HIGH throughout the input data hold time. 5. ADSP LOW always initiates an internal Read at the L-H edge of CLK. A Write is performed by setting one or more byte write enable signals and BWE LOW or GW LOW for the subsequent L-H edge of CLK. Refer to the Write timing diagram for clarification.
Write Truth Table
Operation READ READ WRITE Byte 1 WRITE all bytes WRITE all bytes
GW BWE BW1 BW2 BW3 BW4
H H H H L
H L L L X
X H L L X
X H H L X
X H H L X
X H H L X
PRELIMINARY
(December, 1998, Version 1.2)
6
AMIC Technology, Inc.
A63L7332 Series
Linear Burst Address Table (MODE = LOW)
First Address (External) X . . . X00 X . . . X01 X . . . X10 X . . . X11 Second Address (Internal) X . . . X01 X . . . X10 X . . . X11 X . . . X00 Third Address (Internal) X . . . X10 X . . . X11 X . . . X00 X . . . X01 Fourth Address (Internal) X . . . X11 X . . . X00 X . . . X01 X . . . X10
Interleaved Burst Address Table (MODE = HIGH or NC)
First Address (External) X . . . X00 X . . . X01 X . . . X10 X . . . X11 Second Address (Internal) X . . . X01 X . . . X00 X . . . X11 X . . . X10 Third Address (Internal) X . . . X10 X . . . X11 X . . . X00 X . . . X01 Fourth Address (Internal) X . . . X11 X . . . X10 X . . . X01 X . . . X00
Absolute Maximum Ratings*
Power Supply Voltage (VCC) . . . . . . . . . . -0.5V to +4.6V Voltage Relative to GND for any Pin Except VCC (Vin, Vout) . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VCC +0.5V Power Dissipation (PD) . . . . . . . . . . . . . . . . . . . . . . . . 2W Operating Temperature (Topr) . . . . . . . . . . . 0 to 70 C C Storage Temperature (Tbias) . . . . . . . . . . -10 to 85 C C Storage Temperature (Tstg) . . . . . . . . . . . -55 to 125 C C
*Comments
Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to this device. These are stress ratings only. Functional operation of this device at these or any other conditions above those indicated in the operational sections of this specification is not implied or intended. Exposure to the absolute maximum rating conditions for extended periods may affect device reliability.
Recommended DC Operating Conditions
(0 TA 70 VCC, VCCQ = 3.3V+10% or 3.3V-5%, unless otherwise noted) C C, Symbol VCC VCCQ GND VIH VIHQ VIL Parameter Supply Voltage (Operating Voltage Range) Isolated Input Buffer Supply Supply Voltage to GND Input High Voltage Input High Voltage (I/O Pins) Input Low Voltage Min. 3.1 3.1 0.0 2.0 2.0 -0.3 Typ. 3.3 3.3 Max. 3.6 VCC 0.0 VCC+0.3 VCC+0.3 0.8 Unit V V V V V V 1, 2 1, 2 Note
PRELIMINARY
(December, 1998, Version 1.2)
7
AMIC Technology, Inc.
A63L7332 Series
DC Electrical Characteristics
(0 TA 70 VCC, VCCQ = 3.3V+10% or 3.3V-5%, unless otherwise noted) C C, Symbol ILI ILO Parameter Input Leakage Current Output Leakage Current Min. Max. 2.0 2.0 Unit A A Test Conditions All inputs VIN = GND to VCC
OE = VIH, Vout = GND to VCC
Note
ICC1
Supply Current
-
350
mA
Device selected; VCC = max. Iout = 0mA, all inputs = VIH or VIL Cycle time = tKC min. Device deselected; VCC = max. All inputs are fixed. All inputs VCC - 0.2V or GND + 0.2V Cycle time = tKC min. ZZ VCC - 0.2V IOL = 8 mA IOH = -4 mA
3, 11
ISB1
Standby Current
-
38
mA
11
ISB2 VOL VOH Output Low Voltage Output High Voltage
2.4
10 0.4 -
mA V V
Capacitance
Symbol CIN CI/O Parameter Input Capacitance Input/Output Capacitance Typ. 3 4 Max. 4 5 Unit pF pF Conditions TA = 25 C; f = 1MHz VCC = 3.3V
* These parameters are sampled and not 100% tested.
PRELIMINARY
(December, 1998, Version 1.2)
8
AMIC Technology, Inc.
A63L7332 Series
AC Characteristics (0 TA 70 VCC = 3.3V+10% or 3.3V-5%) C C,
Symbol Parameter Min. tKC tKH tKL tKQ tKQX tKQLZ tKQHZ tOEQ tOELZ tOEHZ Clock Cycle Time Clock High Time Clock Low Time Clock to Output Valid Clock to Output Invalid Clock to Output in Low-Z Clock to Output in High-Z
OE to Output Valid OE to Output in Low-Z OE to Output in High-Z
-4.2 Max. 4.2 4.2 4.2 4.2 Min. 7.5 1.9 1.9 1.5 1.5 1.5 0 -
-4.5 Max. 4.5 4.5 4.5 4.5 Min. 10 3.2 3.2 1.5 1.5 1.5 0 -
-5.0 Max. 5.0 5.0 5.0 5.0
Unit
Note
7 1.9 1.9 1.5 1.5 1.5 0 -
ns ns ns ns ns ns ns ns ns ns 5, 6 5, 6 8 5, 6 5, 6
Setup Times tAS tADSS Address Address Status ( ADSC , ADSP ) Address Advance ( ADV ) Write Signals ( BW1 , BW2 , BW3 , BW4 , BWE , GW ) Data-in Chip Enable ( CE , CE2, CE2 ) 2.0 2.0 2.0 2.0 2.0 2.0 ns ns 7, 9 7, 9
tADVS tWS
2.0 2.0
-
2.0 2.0
-
2.0 2.0
-
ns ns
7, 9 7, 9
tDS tCES
2.0 2.0
-
2.0 2.0
-
2.0 2.0
-
ns ns
7, 9 7, 9
PRELIMINARY
(December, 1998, Version 1.2)
9
AMIC Technology, Inc.
A63L7332 Series
AC Characteristics (continued)
Symbol Parameter Min. Hold Times tAH tADVH Address Address Status ( ADSC , ADSP ) Address Advance ( ADV ) Write Signal ( BW1 , BW2 , BW3 , BW4 , BWE , GW ) Data-in Chip Enable ( CE , CE2, CE2 ) 0.5 0.5 0.5 0.5 0.5 0.5 ns ns 7, 9 7, 9 -4.2 Max. Min. -4.5 Max. Min. -5.0 Max. Unit Note
tAAH tWH
0.5 0.5
-
0.5 0.5
-
0.5 0.5
-
ns ns
7, 9 7, 9
tDH tCEH
0.5 0.5
-
0.5 0.5
-
0.5 0.5
-
ns ns
7, 9 7, 9
Notes: 1. All voltages refer to GND. 2. Overshoot: VIH +4.6V for t tKC/2. Undershoot: VIH -0.7V for t tKC/2. Power-up: VIH +3.6 and VCC 3.1V for t 200ms 3. ICC is given with no output current. ICC increases with greater output loading and faster cycle times. 4. Test conditions assume the output loading shown in Figure 1, unless otherwise specified. 5. For output loading, CL = 5pF, as shown in Figure 2. Transition is measured 150mV from steady state voltage. 6. At any given temperature and voltage condition, tKQHZ is less than tKQLZ and tOEHZ is less than tQELZ. 7. A WRITE cycle is defined by at least one Byte Write enable LOW and ADSP HIGH for the required setup and hold times. A READ cycle is defined by all byte write enables HIGH and ( ADSC or ADV LOW) or ADSP LOW for the required setup and hold times. 8. OE has no effect when a Byte Write enable is sampled LOW. 9. This is a synchronous device. All addresses must meet the specified setup and hold times for all rising edges of CLK when either ADSP or ADSC is LOW and the chip is enabled. All other synchronous inputs must meet the setup and hold times with stable logic levels for all rising edges of clock (CLK) when the chip is enabled. Chip enable must be valid at each rising edge of CLK when either ADSP or ADSC is LOW to remain enabled. 10. The load used for VOH, VOL testing is shown in Figure 2. AC load current is higher than the given DC values. AC I/O curves are available upon request. 11. "Device Deselected" means device is in POWER-DOWN mode, as defined in the truth table. "Device Selected" means device is active (not in POWER-DOWN mode). 12. MODE pin has an internal pulled-up, and ZZ pin has an internal pulled-down. All of then exhibit an input leakage current of 10A. 13. Snooze (ZZ) input is recommended that users plan for four clock cycles to go into SLEEP mode and four clocks to emerge from SLEEP mode to ensure no data is lost.
PRELIMINARY
(December, 1998, Version 1.2)
10
AMIC Technology, Inc.
A63L7332 Series
Timing Waveforms
tKC CLK tKH tADSS ADSP tADSS ADSC tAS ADDRESS A1 tWS GW,BWE BW1-BW4 tCES CE (NOTE *2) (NOTE *4) tADVS ADV ADV suspends burst OE (NOTE *3) tKQLZ DOUT High-Z tKQ Single READ tOEHZ Q(A1) tOEQ tOELZ Q(A2) (NOTE *1) BURST READ tKQ tKQX Q(A2+1) Q(A2+2) Q(A2+3) Q(A2) Q(A2+1) Q(A3) tKQHZ tADVH tCEH Delselected cycle tWH tAH A2 A3 Burst continued with new base address tADSH tADSH tKL
Burst wraps around to its initial state
Read Timing
Notes: *1. Q(A2) refers to output from address A2. Q(A2+1) refers to output from the internal burst address immediately following A2. *2. Timing for CE2 and CE2 is identical to that for CE . As shown in this diagram, when CE is LOW, CE2 is LOW and CE2 is HIGH. When CE is HIGH, CE2 is HIGH and CE2 is LOW. *3. Timing shown assumes that the device was not enabled before entering this sequence. OE does not cause Q to be driven until after the rising edge of the following clock.
PRELIMINARY
(December, 1998, Version 1.2)
11
AMIC Technology, Inc.
A63L7332 Series
Timing Waveforms (continued)
tKC CLK tKH tADSS ADSP tADSS ADSC tAS ADDRESS A1 tAH A2 BYTE WRITE signals are ignored for first cycle when ADSP initiates burst BWE,BW1-BW4 (NOTE *5) tWS GW tCES CE (NOTE *2) tADVS ADV (NOTE *4) ADV suspends burst tADVH tCEH tWH A3 tWS tWH tADSH ADSC extends burst tADSS tADSH tADSH tKL
OE
(NOTE *3) tDS tDH D(A1) tOEHZ D(A2) D(A2+1) (NOTE *1) D(A2+1) D(A2+2) D(A2+3) D(A3) D(A3+1) D(A3+2)
DIN
High-Z
DOUT BURST READ Single WRITE Extended BURST WRITE
Write Timing
Notes: *1. D(A2) refers to output from address A2. D(A2+1) refers to output from the internal burst address immediately following A2. *2. Timing for CE2 and CE2 is identical to that for CE . As shown in the above diagram, when CE is LOW, CE2 is LOW and CE2 is HIGH. When CE is HIGH, CE2 is HIGH and CE2 is LOW. *3. OE must be HIGH before the input data setup, and held HIGH throughout the data hold period. This prevents input/output data contention for the period prior to the time Byte Write enable inputs are sampled. *4. ADV must be HIGH to permit a Write to the loaded address. *5. Byte Write enables are decided by means of a Write truth table.
PRELIMINARY
(December, 1998, Version 1.2)
12
AMIC Technology, Inc.
A63L7332 Series
Timing Waveforms (continued)
tKC CLK tKH tADSS ADSP tADSH tKL
ADSC tAS ADDRESS A1 tAH A2 A3 tWS GW,BWE, BW1-BW4 (NOTE *3) tCES CE (NOTE *2) tCEH tWH A4 A5 A6
ADV
OE tDS tKQ DIN High-Z tKQLZ DOUT High-Z Q(A1) Back-to-Back READs tOEHZ Q(A2) Single WRITE D(A3) tKQ (NOTE *1) Q(A3) Pass-through READ (NOTE *4) Q(A4) Q(A4+1) Q(A4+2) Q(A4+3) Back-to-Back WRITEs tDH tOELZ D(A5) D(A6)
BURST READ
Read/Write Timing
Notes: *1. Q(A4) refers to output from address A4. Q(A4+1) refers to output from the internal burst address immediately following A4. *2. Timing for CE2 and CE2 is identical to that for CE . As shown in this diagram, when CE is LOW, CE2 is LOW and CE2 is HIGH. When CE is HIGH, CE2 is HIGH and CE2 is LOW. *3. Byte Write enables are decided by means of a Write truth table. *4. Pass-through occurs when data is first written, then Read in sequence.
PRELIMINARY
(December, 1998, Version 1.2)
13
AMIC Technology, Inc.
A63L7332 Series
AC Test Conditions
Input Pulse Levels Input Rise and Fall Times Input Timing Reference Levels Output Reference Levels Output Load GND to 3V 1.5ns 1.5V 1.5V See Figures 1 and 2
Q 350 5pF Q ZO=50 RL=50 VT=1.5V
Figure 1. Output Load Equivalent
+3.3V 320
Figure 2. Output Load Equivalent
PRELIMINARY
(December, 1998, Version 1.2)
14
AMIC Technology, Inc.
A63L7332 Series
Ordering Information
Part No. A63L7332E-4.2 A63L7332E-4.5 A63L7332E-5 Access Times (ns) 4.2 4.5 5.0 Package 100L LQFP 100L LQFP 100L LQFP
PRELIMINARY
(December, 1998, Version 1.2)
15
AMIC Technology, Inc.
A63L7332 Series
Package Information LQFP 100L Outline Dimensions
unit: inches/mm
HE E
80 51
A2
A1 y D
81
50
HD D
100
31
1
30
e
b
c
Symbol A1 A2 b c HE E HD D e L L1 y
Dimensions in inches Min. 0.002 0.053 0.011 0.005 0.860 0.783 0.624 0.547 Nom. 0.055 0.013 0.866 0.787 0.630 0.551 0.026 BSC 0.018 0.024 0.039 REF 0 3.5 0.004 7 0.030 Max. 0.057 0.015 0.008 0.872 0.791 0.636 0.555
Dimensions in mm Min. 0.05 1.35 0.27 0.12 21.85 19.90 15.85 13.90 Nom. 1.40 0.32 22.00 20.00 16.00 14.00 0.65 BSC 0.45 0.60 1.00 REF 0 3.5 0.1 7 0.75 Max. 1.45 0.37 0.20 22.15 20.10 16.15 14.10
Notes: 1. Dimensions D and E do not include mold protrusion. 2. Dimensions b does not include dambar protrusion. Total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot.
L
L1
PRELIMINARY
(December, 1998, Version 1.2)
16
AMIC Technology, Inc.

▲Up To Search▲

Price & Availability of A63L7332

	To Download A63L7332 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .