|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
User-Friendly Fiber-Optic Amplifier Solve Your Basic Sensing Challenges Easily with the E3X-NA Series I I I E3X-NA I I I I I I Streamlined features provide basic sensing immediately after plug-in Wire-saving amplifiers reduce installation time and minimize space requirements Master/slave connector design affords connectivity for up to 16 wire-saving amplifiers Use the LED bar display to quickly confirm sensor performance Optical communication design prevents mutual interference for up to 5 amplifiers Green LED models address mark-detecting applications High-speed models have a response time of 50 s Select a water-resistant model (IP66 rating) using an M8 connector Prewired water-resistant models are available Ordering Information: Amplifier Units, Connectors, Accessories and Fiber-Optics I Amplifier Units with Cables Part number NPN output PNP output E3X-NA41 E3X-NA41F E3X-NAG41 ON/OFF E3X-NA11 E3X-NA11F E3X-NAG11 Type Standard High-speed Mark-detection Control output Appearance Water-resistant E3X-NA11V E3X-NA41V E3X-NA I E3X-NA Connector-Ready Amplifiers (Order Connector Separately) Part number NPN output PNP output E3X-NA8 E3X-NA6 Item Wire-saving Applicable connector (order separately) Master E3X-CN11 Control output ON/OFF output Appearance Slave E3X-CN12 Water-resistant (M8 connectors) E3X-NA14V E3X-NA44V XS3F-M421-40@-A @ XS3F-M422-40@-A @ I Amplifier Unit Connectors (Order Separately) Stickers for Connectors are included as accessories. Note: Item Master Connector Slave Connector Appearance Cable length 2m No. of conductors 3 1 Part number E3X-CN11 E3X-CN12 I Combining Amplifier Units and Connectors (Each Sold Separately) Amplifier Units Type Wire-saving models NPN E3X-NA6 PNP E3X-NA8 Applicable Connectors (Order Separately) Master Connector Slave Connector E3X-CN12 (1-wire) Refer to the following tables when placing an order. Amplifier Units and Connectors are sold separately. + E3X-CN11 (3-wire) Example: When Using 5 Amplifier Units Amplifier Units (5 Units) + 1 Master Connector + 4 Slave Connectors I Sensor I/O Connectors (Order Separately) Cable specifications Standard cable Size M8 Appearance Straight connector Cable type 2m 5m Four-core cable Part number XS3F-M421-402-A XS3F-M421-405-A XS3F-M422-402-A XS3F-M422-405-A L-shaped connector 2m 5m I Accessories (Order Separately) Applicable models E3X-NA@ E3X-NA@F E3X-NAG@ E3X-NA@V I Fiber-Optic Cables Mounting Brackets Appearance Quantity 1 Part number E39-L143 The E3X-NA amplifiers use Omron's E32-series fiber-optic cables. With a choice of over 80 sensing heads, you are sure to find one that matches your application requirements. Refer to the selection of E32 cables (listed with their respective sensing distances) in the fiber section at the end of this data sheet. Order fiber-optic cables separately. E39-L148 End Plate Appearance Quantity 1 Part number PFP-M 2 E3X-NA E3X-NA Specifications I Amplifier Units Amplifier Units with Cables Standard models High-speed detection models E3X-NA11F E3X-NA41F Mark-detecting models E3X-NAG11 E3X-NAG41 Green LED (520 nm) 35 mA max. (for 24-VDC power supply) 35 mA max. Water-resistant models E3X-NA11V E3X-NA41V Red LED (680 nm) Connector-ready amplifier units Wire-saving models E3X-NA6 E3X-NA8 Water-resistant models (use M8 connectors) E3X-NA14V E3X-NA44V Ratings/Characteristics Item Output type NPN output PNP output E3X-NA11 E3X-NA41 Red LED (680 nm) Light source (wavelength) Supply voltage Current consumption 12 to 24 VDC 10%, ripple (p-p): 10% max. 35 mA max. Control output Operation mode Switchselectable Response time NPN/PNP (depends on model) open collector; load current: 50 mA max.; residual voltage: 1 V max. Light-ON/Dark-ON operation 200 s max. for operation and reset respectively (See note.) Operation: 20 s max. Reset: 30 s max. 200 s max. for operation and reset respectively (See Note.) Sensitivity adjustment Circuit protection 8-turn sensitivity adjuster (with indicator) Reverse polarity, output Reverse short-circuit, mutual inter- polarity, output ference prevention (opti- short-circuit cally synchronized) OFF-delay timer: 40 ms (fixed) Incandescent lamp:10,000 lux max. Sunlight:20,000 lux max. Operating: Groups of 1 to 3 Amplifiers: -25C to 55C (-13F to 131F) Groups of 4 to11 Amplifiers: -25C to 50C (-13F to 122F) Groups of 12 to16 Amplifiers: -25C to 45C (-13F t0 113F) with no icing or condensation Storage: -30C to 70C (-22 F to 158F) with no icing or condensation Operating and storage: 35% to 85% (with no condensation) 20 M min. (at 500 VDC) 1,000 VAC at 50/60 Hz for 1 minute 10 to 55 Hz with a 1.5-mm double amplitude for 2 hrs each in X, Y and Z directions 500 m/s2, for 3 times each in X, Y and Z directions IEC60529 IP50 (with Protective Cover attached) IEC60529 IP66 (with Protective Cover attached) IEC60529 IP50 (with Protective Cover attached) Connector Approx. 110 g Polyethersulfone (PES) IEC60529 IP66 (with Protective Cover attached) 500 VAC at 50/ 60 Hz for 1 minute Reverse polarity, output short-circuit, mutual interference prevention (optically synchronized) Timer function Ambient illumination (receiver side) Ambient temperature Ambient humidity Insulation resistance Dielectric strength Vibration resistance Shock resistance Enclosure rating Connection method Weight (packed) Material Case Cover Accessories Note: Prewired (standard cable length: 2 m) Approx. 100 g Polybutylene terephthalate (PBT) Polycarbonate Instruction Sheet M8 connector Approx. 55 g Approx. 65 g Polycarbonate Polyethersulfone (PES) When there are 8 or more Amplifier Units mounted side-by-side, the response time will be 350 s max. I Amplifier Unit Connectors E3X-CN11 2.5 A 50 V 20 m max. (20 mVDC max., 100 mA max.) (The above figure is for connection to the Amplifier Unit and the adjacent Connector. It does not include the conductor resistance of the cable.) 50 times (for connection to the Amplifier Unit and the adjacent Connector) Polybutylene terephthalate (PBT) Phosphor bronze/gold-plated nickel Approx. 55 g Approx. 25 g Housing Contact Item Rated current Rated voltage Contact resistance E3X-CN12 Number of insertions Material Weight (packed) 3 E3X-NA E3X-NA Nomenclature I Amplifier Units Sensitivity Indicator 8-Turn Sensitivity Adjuster Lock Button Incident level Indicators Operation Indicator Operation Mode Selector Use to switch between Light ON and Dark ON modes. Timer Switch ON: Timer function is ON. OFF: Timer function is OFF. I LED Bar Display Indicators In addition to an operation indicator (orange), the E3X-NA also has incident level indicators (4 green and 1 red). Use these indicators for optical axis adjustments and maintenance. Status of indicators (in L/ON mode) Operation indicator (in L/ON mode) Not lit Incident level Operation indicator Incident level indicators Approx. 80% max. of operating level Not lit Lit (See note.) Not lit Approx. 80% to 90% of operating level Not lit or lit Approx. 90% to 110% of operating level Lit Approx. 110% to 120% of operating level Lit Approx. 120% min. of operating level Note: The indicator farthest to the right will be lit even if the incident level is 0. 4 E3X-NA E3X-NA Operation I Output Circuits Model Mode selector LIGHT ON (L/ON) Timing chart State of Output circuit output transistor Light ON T Operation indicator (orange) Photoelectric Sensor main circuit 1 Output NPN E3X-NA11 E3X-NA6 E3X-NAG11 E3X-NA11F E3X-NA11V E3X-NA14V Incident light No incident light Operation indicator ON (orange) OFF Output transistor Load (relay) ON OFF Brown Load Black 4 Control output Operate Release (Between brown and black) 12 to 24 VDC Blue 3 DARK ON (D/ON) Incident light No incident light Operation indicator ON (orange) OFF Output transistor Load (relay) ON OFF Dark ON T M8 Connector Pin Arrangement 2 1 4 3 Operate Release (Between brown and black) Note: Light ON Pin 2 is not used. Brown 1 PNP E3X-NA41 E3X-NA8 E3X-NAG41 E3X-NA41F E3X-NA41V E3X-NA44V LIGHT ON (L/ON) Incident light No incident light Operation indicator ON (orange) OFF Output transistor Load (relay) ON OFF T Operate Release (Between brown and black) Operation indicator (orange) Photoelectric Sensor main circuit 4 Black Control output 12 to 24 VDC Load Blue 3 DARK ON (D/ON) Incident light No incident light Operation indicator ON (orange) OFF Output transistor Load (relay) ON OFF Dark ON T M8 Connector Pin Arrangement 2 1 4 3 Operate Release (Between brown and black Note: Pin 2 is not used. I Connectors (Sensor I/O Connectors) Terminal number 4 3 2 1 1 2 3 4 Color of cable conductors Brown White Blue Black XS3F-M421-402-A, XS3F-M422-402-A XS3F-M421-405-A, XS3F-M422-405-A Classification DC Color of cable conductors Brown White Blue Black Connection pin number 1 2 3 4 Application Power supply (+V) --Power supply (0 V) Output Note: Pin 2 is not used. 5 E3X-NA E3X-NA Engineering Data (Typical) I Parallel Operating Range E32-T11L/T12L Distance Y (mm) X At max. sensitivity. (Use for optical axis adjustment at installation.) Distance Y (mm) 300 300 200 Distance Y (mm) E32-TC200 E3X-NAG@ 200 100 0 -100 -200 Y E32-T11R X Y 200 150 X E3X-NAG@ 100 50 0 -50 0.1 0.2 0.3 0.4 Y E3X-NAG@ 100 0 0.2 0.4 0.6 0.8 1 1.2 0.5 1 1.5 2 2.5 0.5 0.6 0.7 Distance X (m) -100 Distance X (m) E3X-NA@F Distance X (m) -100 E3X-NA@F -300 E3X-NA@ (V) -200 E3X-NA@ (V) -300 -150 -200 E3X-NA@F E3X-NA@ (V) E32-T11 Distance Y (mm) 200 150 100 50 0 -50 -100 -150 -200 0.2 0.4 0.6 0.8 1 E32-TC200E Distance Y (mm) E3X-NAG@ X Y E32-T24S Distance Y (mm) X 80 60 40 20 0 50 100 150 200 30 20 10 0 X Y E3X-NAG@ Y 250 300 0.4 0.8 1.2 1.6 2 Distance X (m) -20 E3X-NA@F -40 -60 Distance X (mm) -10 -20 Distance X (m) E3X-NA@ (V) -80 E3X-NA@F E3X-NA@ (V) -30 E3X-NA@F E3X-NA@ (V) I Operating Range E32-D11L Distance Y (mm) X Y With standard sensing target at max. sensitivity. (Use for the positioning of the object and Sensor.) E32-DC200 Distance Y (mm) 150 100 E32-D11R/D12R Distance Y (mm) X Y 150 100 30 20 10 0 X E3X-NAG@ 50 0 E3X-NAG@ 50 0 -50 E3X-NAG@ Y 200 -50 -100 -150 300 400 300 100 200 400 500 40 80 120 160 200 100 Distance X (mm) Distance X (mm) -10 -20 -30 Distance X (mm) E3X-NA@F E3X-NA@ (V) -100 -150 E3X-NA@F E3X-NA@ (V) E3X-NA@F E3X-NA@ (V) E32-DC200E Distance Y (mm) 15 10 X Y Distance Y (mm) Distance Y (mm) E32-D33 15 10 X Y E32-L25L 1 X Y E3X-NA@F E3X-NAG@ 5 0 10 -5 E3X-NA@F 5 0 5 -5 10 15 0.5 20 30 40 50 60 70 20 Distance X (mm) 25 0 2 4 6 8 10 Distance X (mm) -0.5 Distance X (mm) -10 -15 -10 E3X-NA@ (V) E3X-NA@F E3X-NA@ (V) -15 -1 E3X-NA@ (V) 6 E3X-NA I E3X-NA Number of Turns of Sensitivity Adjuster vs. Sensing Distance E32-D11L Distance (mm) 400 1.2 1.0 0.8 E32-T11L Distance (m) 300 E3X-NA@ (V) 0.6 0.4 200 E3X-NA@ (V) 100 0.2 E3X-NA@F 0 2 4 6 8 10 0 2 4 6 @F 8 10 Number of turn ns Number of t turns Sensing Distance vs. Hysteresis E32-T11L Hysteresis (mm) 100 80 E32-D11L Hysteresis (mm) 20 15 60 E3X-NA@ (V) 40 10 E3X-NA@ (V) 20 5 0 100 200 300 400 500 600 700 0 50 100 150 200 Distance (mm) (mm Distance (mm) 7 E3X-NA E3X-NA Dimensions Unit: mm (inch) I Amplifier Units Incident level indicators A (See note 1.) Operation indicator Amplifier Units with Cables (with Mounting Bracket Attached) E3X-NA11 E3X-NA11F E3X-NA41 E3X-NA41F E3X-NAG11 E3X-NAG41 Two, 2.4 dia. 10 (0.39) Cable (See note 2.) 13.05 15.75 3 9.2 64.3 (2.53) 38.6 5.3 Mounting Holes 8 31.5 (1.24) 9.9 10.7 4.1 22.4 13 16 34.8 4 10.75 16 Two, M3 Hole for optical communications (See note 3.) 2.4 Two, 3.2 dia. holes 3.4 4.4 Mounting bracket (E39-L143) Stainless steel (SUS304) 22.4 16 Note: 1. The mounting bracket can also be used on side A. 2. With these models, a 4-dia., 3-conductor, vinyl-insulated round cable (conductor cross-sectional area: 0.45 mm 2; insulation diameter: 1.1 mm) is used. Standard length: 2 m. 3. The hole for optical communications is for preventing mutual interference. There is no hole for E3X-NA@F models. Water-Resistant Amplifier Units with Cables (with Mounting Bracket Attached) E3X-NA11V E3X-NA41V 28.65 25.95 9.2 (See note 2.) Operation indicator Incident level indicators 81.5 (3.21) 12 (0.47) 6.9 40 A (See note 1.) Two, 2.4 dia. 2.8 8 33 (1.29) 9.9 10.7 11.2 3.9 3.4 4.3 11.5 23.9 14.4 23.9 16 37 67.2 16 3.4 5.4 Hole for optical communications Mounting Holes Two, M3 6.6 Mounting bracket (E39-L148) Stainless steel (SUS304) 16 5.4 3.4 Note: 1. The mounting bracket can also be used on side A. 2. With these models, a 4-dia., 3-conductor, vinyl-insulated round cable (conductor cross-sectional area: 0.45 mm 2; insulation diameter: 1.1 mm) is used. Standard length: 2 m. 8 E3X-NA Wire-Saving Amplifiers Incident level indicators E3X-NA E3X-NA6 E3X-NA8 Operation indicator 10 (0.39) 13.05 15.75 9.2 64.3 (2.53) Two, 2.4 dia. 3 8 9.9 10.7 3.4 1.8 13 5.1 3.9 1.7 4.2 1.8 38.6 36.7 31.5 14 (1.24) 5.5 Hole for optical communications (for preventing mutual interference) 6.2 1.7 Dimensions with Master Connector Connected 71 (2.80) 67.5 64.3 Dimensions with Slave Connector Connected 71 (2.80) 67.5 64.3 31.5 (1.24) 1.5 E3XCN11: 4.0 dia. 31.5 (1.24) E3X-CN12: 2.6 dia. 12.95 1.5 17.45 12.95 11.55 1.8 5.1 3.9 4 10 (0.39) 1.8 5.1 3.9 3 4.8 4 10 (0.39) M8 Connector-Ready, Water-Resistant Amplifier Units E3X-NA14V E3X-NA44V 28.65 25.95 9.2 Operation indicator Incident level indicators 12 (0.47) The mounting bracket can also be used on this side. 81.5 (3.21) 6.9 40 Two, 2.4 dia. 33 (1.30) 2.8 M8 8 9.9 10.7 11.2 3.9 3.4 4.3 11.5 23.9 14.4 16 37 67.2 16 3.4 5.4 Hole for optical communications 11 Mounting Holes Two, M3 23.9 Mounting bracket (E39-L148) Stainless steel (SUS304) 16 5.4 3.4 9 E3X-NA I E3X-NA Amplifier Unit Connectors (Order Separately) 10 6 2.9 2.6 2 m (6.56 ft.) 10.7 6.8 4 Master Connectors E3X-CN11 See note. 4 dia. 14.4 6 0.8 8.4 15.1 302 50 +5 0 102 Note: A 4-dia., 3-conductor, vinyl-insulated round cable (conductor cross-sectional area: 0.2 mm2; insulation diameter: 1.1 mm) is used. Slave Connectors E3X-CN12 2.9 10 6 2 m (6.56 ft.) 10.7 6.8 2.6 4 See note. 2.6 dia. 14.4 6 3 0.8 8.4 15.1 302 50 +5 0 102 Note: A 2.6-dia., single-conductor, vinyl-insulated round cable (conductor cross-sectional area: 0.2 mm2; insulation diameter: 1.1 mm) is used. I Sensor I/O Connectors (Order Separately) Straight Connector (at One End of Cable) XS3F-M421-402-A (L=2 m) XS3F-M421-405-A (L=5 m) 2.15 M8 12.9 4 2 9 dia. 1.95 0.5 3 3.4 1 21.5 31.4 L 30 50 5 4 dia. L-shaped Connector (at One End of Cable) XS3F-M422-402-A (L=2 m) XS3F-M422-405-A (L=5 m) L 23.1 30 50 5 20.5 4 dia. 9 dia. 3.4 2.15 0.5 1.95 10 E3X-NA I E3X-NA Accessories (Order Separately) Mounting Bracket for E3X-NA@, E3X-NA@F, and E3X-NAG@ Models E39-L143 10.3 5.3 7.3 26.8 7 160.1 3 2.5 34.8 (1.37) 22 16 3 Mounting Holes Two, M3 Two, 3.2 dia. Material: Stainless steel (SUS 304) 10.3 10 max. 7 3 16 Four, R1.7 3.4 1 3.4 1 Mounting Bracket for E3X-NA@V Models E39-L148 12 12 max. 9 2 3.4 9.5 22 16 160.1 7.3 3 4 27 35 (1.38) 3 4.3 1.5 9.1 Two, 3.2 dia. R1.7 16 R1.7 3.4 2 Mounting Holes Two, M3 Material: Stainless steel (SUS 304) End Plate PFP-M 10 50 (1.97) 11.5 M4x8, pan-head screw M4 spring washer 4.8 1 1.3 1.8 35.5 35.3 1.8 6.2 10 . 11 E3X-NA E3X-NA Precautions I Wiring Precautions I Wiring the Amplifier Unit Read the following before using the Amplifier Unit and Sensor to ensure safety. Cable The cable can be extended, provided that the extension wire applied is at least 0.3 mm2 thick and the total distance no more than 100 m. Do not pull the cable with a force exceeding 30N. Separation from Power or High-tension Lines Do not wire power lines or high-tension lines alongside the lines of the Amplifier Unit in the same conduit, otherwise the Amplifier Unit may be damaged or malfunction due to induction. Be sure to wire the lines of the Amplifier Unit as far as possible from power lines or high-tension lines or laid in an exclusive, shielded conduit. Power Supply Voltage Do not impose any voltage exceeding the rated voltage on the E3X-NA. Do not impose AC power (100 VAC) on models that operate with DC. In both cases, the E3X-NA may burst or burn. Load Short-circuits Do not short-circuit the load connected to the E3X-NA, or the E3X-NA may burst or burn. Polarity When supplying power to the E3X-NA, make sure that the polarity of the power is correct, or the E3X-NA may burst or burn. No-load Operation A load must be connected to the E3X-NA during operation, or internal elements may burst or burn. Always wire through a load. Power line Incorrect Operating Environment * Do not use the Amplifier Unit or Sensor in places with flammable or explosive gas. * Do not use the Amplifier Unit or Sensor underwater. * Do not disassemble, repair, or modify the Amplifier Unit or Sensor. I Power Supply If a standard switching regulator is used as a power supply, the frame ground (FG) terminal and the ground (G) terminal must be grounded, or faulty operation may result from the switching noise of the power supply. M8 Metal Connectors (Water-Resistant Models) Turn OFF the power before inserting or removing the connector. Hold the connector cover when inserting or removing the connector. Tighten the fixing screws by hand. Using tools such as pliers may cause damage. The applicable tightening torque range is 0.3 to 0.4 N*m. If tightening is insufficient, the enclosure rating may not be maintained, and vibrations may cause the connector to come loose. Power Turning Power ON The Sensor is ready to operate within 100 ms after the power supply is turned ON. If the Sensor and load are connected to power supplies separately, be sure to turn ON the power supply to the Sensor first. Turning Power OFF Pulses may be output when the power is turned OFF. Always turn OFF the power to the load or the load line first. Power Supply Type Do not connect the E3Z-NA to a full-wave or half-wave rectified power supply. Communications Hole The hole on the side of the Amplifier Unit is a communications hole for preventing mutual interference when Amplifier Units are mounted side-by-side. The E3X-MC11 Mobile Console (sold separately) cannot be used. If an excessive amount of light is received via the Sensor, the mutual interference prevention function may not work. In this case, make the appropriate adjustments using the sensitivity adjuster. The mutual interference prevention function will not operate when the E3X-NA is used side-by-side with E3X-DA-N models. 12 E3X-NA I E3X-NA Removal Pull the lock tab of the Amplifier Unit with a flat blade screwdriver in direction (3) and lift the fiber insertion part in direction (4) as shown below. Mounting the Amplifier Unit Mount the Amplifier Units one at a time onto the DIN rail. Joining Amplifier Units 1. (4) 2. Line up the clips and slide the Amplifier Units together. Then press the Amplifier Units together until they click into place. DIN rail (3) When side-mounting using a mounting bracket, secure the mounting bracket to the Amplifier Unit and then mount using M3 screws. Use plain washers of diameter 6mm or less when mounting. Clip Click into place Separating Amplifier Units Slide Amplifier Units away from each other, and remove from the DIN rail one at a time. (Do not attempt to remove Amplifier Units from the DIN rail without separating them first.) Note: 1. The specifications for ambient temperature will vary according to the number of Amplifier Units used together. For details, refer to Ratings/Characteristics in the Specifications section of this data sheet. 2. Always turn OFF the power supply before joining or separating Amplifier Units. Ambient Conditions Dust or dirt accumulation on the optical communications hole may prevent normal communications. Be sure to remove any dust or dirt before using the Unit. Plain washers (6-mm dia. max.) Operating Environment Mounting 1. Mount the front part on the mounting bracket E39-L143 or E39-L148 (order separately) or onto a DIN rail. Do not mount the back of the Amplifier Unit onto the mounting bracket or the DIN rail first, or the mounting strength of the Amplifier Unit may be reduced. Always mount the front of the Amplifier Unit first. Ratings and Specifications The ratings and performance specifications for items such as the minimum sensing target and characteristics are based on products taken at random from certain production lots. Use this data as reference only. 2. Press the back part onto the mounting bracket or the DIN rail. Note: Protective Cover Be sure to mount the Protective Cover before use. (2) (1) DIN rail 13 E3X-NA I E3X-NA Mounting the Fiber Unit Tightening Force The tightening force applied to the Fiber Unit should be as shown below. Protective cover Unlocked Screw-Mounting Model Spring mounting clip Toothed washers Cylindrical Model Retaining screw (flat head or sunken head) (M3 max.) Locked Nuts (attachment) Note: To maintain the fiber properties, confirm that the lock is released before removing the fiber. 3. Precautions for Fiber Connection/Disconnection Fiber Units M3/M4 screw M6 screw/ 6-mm dia. cylinder 1.5-mm dia. cylinder 2-mm dia./3-mm dia. cylinder E32-T12F 5-mm dia. Teflon model E32-D12F 6-mm dia. Teflon model E32-T16 E32-R21 E32-M21 E32-L25A E32-T16P E32-T16PR E32-T24S E32-L24L E32-L25L E32-T16J E32-T16JR E32-T16W E32-T16WR 0.49 N*m max. 0.59 N*m max. Up to 5 mm to the tip: 0.49 N*m max. More than 5 mm from the tip: 0.78 N*m max. 0.78 N*m max. 0.29 N*m max. Temporarily fitted Thin fiber attachment (E39-F9) Clamping torque 0.78 N*m max. 0.98 N*m max. 0.2 N*m max. 0.29 N*m max. 0.78 N*m max. Be sure to lock or unlock the lock button within an ambient temperature range between -10C and 40C. Cutting Fiber Insert a fiber into the Fiber Cutter and determine the length of the fiber to be cut. Press down the Fiber Cutter in a single stroke to cut the fiber. The cutting holes cannot be used twice. If the same hole is used twice, the cutting face of the fiber will be rough and the sensing distance will be reduced. Always use an unused hole. Cut a thin fiber as follows: 1. An attachment is temporarily fitted to a thin fiber before shipment. 2. Secure the attachment after adjusting the position of it in the direction indicated by the arrow. 0.3 N*m max. Use a proper-sized wrench. 3. Insert the fiber to be cut into the E39-F4. Cutter (E39-F4) Fiber Connection and Disconnection The E3X-NA Amplifier Unit has a lock button. Connect or disconnect the fibers to or from the E3X-NA Amplifier Unit using the following procedures: 1. Connection Open the protective cover, insert the fibers according to the fiber insertion marks on the side of the Amplifier Unit, and lower the lock button. Lock button Insertion position Three holes for standard fiber (2.2-mm dia.) Two holes for thin fiber 4. Finished state (proper cutting state) Approx. 0.5 mm Insertion direction Note: Insert the fiber in the direction indicated by the arrow. Fiber Fiber insertion mark 10.7 mm 2. Disconnection Remove the protective cover and raise the lock button to pull out the fiber. 14 E3X-NA Connection Do not pull or press the Fiber Units. The Fiber Units have a withstand force of 9.8 N or 29.4 N maximum (pay utmost attention because the fibers are thin). Do not bend the edge of the Fiber Units (excluding the E32-T@R and E32-D@R). I E3X-NA Mounting Amplifier Units with Connectors Insert the Master or Slave Connector into the Amplifier Unit until it clicks into place. Mounting Connectors 1. Correct 20 mm min. Incorrect Amplifier Unit Fiber Unit Insert 2. Join Amplifier Units together as required after all the Master and Slave Connectors have been inserted. 20 mm min. Do not apply excess force on the Fiber Units. 3. Attach the stickers (provided as accessories) to the sides of Master and Slave Connectors that are not connected to other Connectors. Correct Fiber Unit Nylon wireholder Incorrect Sticker Sticker The Fiber Head could be broken by excessive vibration.Use the following method to prevent fiber head breakage: Note: Attach the stickers to the sides with grooves. Removing Connectors 1. Slide the slave Amplifier Unit for which the Connector is to be removed away from the rest of the group. A one-turn loop can absorb vibrations. Tape 2. After the Amplifier Unit has been separated, press down on the lever on the Connector and remove it. (Do not attempt to remove Connectors without separating them from other Amplifier Units first.) Press down Lever Bending Radius E39-F11 Sleeve Bender The bending radius of the stainless steel tube should be as large as possible. The smaller the bending radius becomes, the shorter the sensing distance will be. Insert the tip of the stainless steel tube to the Sleeve Bender and bend the stainless steel tube slowly along the curve of the Sleeve Bender (refer to the figure). 1.2-mm dia. max. 1.3-mm dia. min. R 10 mm R 12.5 mm R 5 mm R 7.5 mm Fiber tip position mark Remove Stainless steel tube 90 max. 10 mm 10 mm Do not bend here. 15 E3X-NA I E3X-NA I Mounting End Plate (PFP-M) Reflector Depending on how it is mounted, an Amplifier Unit may move during operation. In this case, use an End Plate. Before mounting an End Plate, remove the clip from the master Amplifier Unit using a nipper or similar tool. Use of E39-R3 Reflector Use detergent, etc., to remove any dust or oil from the surfaces where tape is applied. Adhesive tape will not be attached properly if oil or dust remains on the surface. The E39-R3 cannot be used in places where it is exposed to oil or chemicals. E39-F32@ Protective Spiral Tubes Insert a fiber to the Protective Spiral Tube from the head connector side (screwed) of the tube. Clip The clip can also be removed using the following mechanism, which is incorporated in the construction of the section underneath the clip. 1. Insert the clip that is to be removed into the slit underneath the clip on another Amplifier Unit. Protective Spiral Tube Fiber Unit Push the fiber into the Protective Spiral Tube. The tube should be straight so that the fiber is not twisted when inserted. Then turn the end cap of the spiral tube. Protective Spiral Tube Fiber Unit Secure the Protective Spiral Tube on a suitable place with the attached nut. Mounting panel Hexagon clamping nut 2. Remove the clip by rotating the Amplifier Unit. Rotate Protective Spiral Tube Fiber Unit Toothed washer Use the attached saddle to secure the end cap of the Protective Spiral Tube. To secure the Protective Spiral Tube at a position other than the end cap, apply tape to the tube so that the portion becomes thicker in diameter. Pull Strengths for Connectors (Including Cables) E3X-CN11: 30 N max. E3X-CN12: 12 N max. Saddle Tube End cap I E39-F10 Fiber Connector Splice Fiber Unit Retention unit Retention unit Fiber Unit Mount the Fiber Connector as shown in the following illustrations. Fiber Unit Fiber Unit The Fiber Units should be as close as possible when they are connected. Sensing distance will be reduced by approximately 25% when fibers are connected. Only 2.2-mm-dia. fibers can be connected. 16 E3X-NA E3X-NA Sensing Distance with Fiber Optic Cables I Through-beam Fiber Units Indicates models that allow free cutting. Models without this mark do not allow free cutting. Refer to the end of the following table for notes and precautions. Free-cut : Red light Application Features : Green light Appearance Applicable Amplifier Unit E3X-NA@ (V) E3X-NAG@ M4 screw Sensing distance (mm) (Values in parentheses: when using the E39-F1 Lens Unit) 700 (2,000) 130 (370) 210 (600) Standard object (see notes) (min. sensing target: opaque) Part number Permissible bending radius 25 mm Long distance M4 Free-cut 1.4-mm dia. (0.03-mm dia.) E32-T11L E3X-NA@F 3-mm dia. Free-cut E3X-NA@ (V) E3X-NAG@ 3-mm dia. 700 130 210 1.4-mm dia. (0.5-mm dia.) 1.4-mm dia. (0.03-mm dia.) E32-T12L E3X-NA@F M3 Free-cut E3X-NA@ (V) E3X-NAG@ M3 screw 200 40 60 200 40 60 14,000 4,200 1.4-mm dia. (0.5-mm dia.) 0.9-mm dia. (0.03-mm dia.) E32-T21L 10 mm E3X-NA@F 2-mm dia.; small diameter Free-cut E3X-NA@ (V) E3X-NAG@ 2-mm dia. 0.9-mm dia. (0.2-mm dia.) 0.9-mm dia. (0.03-mm dia.) E32-T22L E3X-NA@F M14; with lens; ideal Free-cut E3X-NA@ (V) M14 screw for explosion-proofapplications E3X-NA@F E3X-NA@ (V) 400 (3,000) 75 (550) 120 (900) Generalpurpose M4 Free-cut 0.9-mm dia. (0.2-mm dia.) 10-mm dia. (0.1-mm dia.) 10-mm dia. (1.5-mm dia.) 1.0-mm dia. (0.03-mm dia.) E32-T17L 25 mm E32-TC200 25 mm M4 screw E3X-NAG@ E3X-NA@F M3; Free-cut possible to mount the reflective side-view conversion attachment E39-F5 M3; for Free-cut detecting minute sensing targets E3X-NA@ (V) E3X-NAG@ M3 screw 360 65 100 100 1.0-mm dia. (0.2-mm dia.) 1.0-mm dia. (0.03-mm dia.) E32-TC200A 25 mm E3X-NA@F E3X-NA@ (V) E3X-NAG@ M3 screw 1.0-mm dia. (0.2-mm dia.) 0.5-mm dia. (0.03-mm dia.) E32-TC200E 10 mm 20 30 100 E3X-NA@F Thin fiber 2-mm dia.; Free-cut for detecting minute sensing targets 1.2-mm dia.; with sleeve E3X-NA@ (V) E3X-NAG@ 2-mm dia. 0.5-mm dia. (0.1-mm dia.) 0.5-mm dia. (0.03-mm dia.) E32-T22 10 mm 20 30 E3X-NA@F 90 mm (40 mm) Free-cut E3X-NA@ (V) E3X-NAG@ 75 120 100 400 0.5-mm dia. (0.1-mm dia.) 1.0-mm dia. (0.03-mm dia.) E32-TC200B E32-TC200B4 25 mm M4 screw 1.2-mm dia. ( ): E32-TC200B4 E3X-NA@F E3X-NA@ (V) 0.9-mm dia.; with sleeve Free-cut 90 mm (40 mm) M3 screw 0.9-mm dia. ( ): E32-TC200F4 1.0-mm dia. (0.2-mm dia.) 0.5-mm dia. (0.03-mm dia.) E32-TC200F E32-TC200F4 10 mm E3X-NAG@ E3X-NA@F 20 30 0.5-mm dia. (0.1-mm dia.) 17 E3X-NA Application Features Appearance Applicable Amplifier Unit E3X-NA@ (V) E3X-NAG@ M4 screw E3X-NA Sensing distance (mm) (Values in parentheses: when using the E39-F1 Lens Unit) 360 65 100 100 Standard object (see notes) (min. sensing target: opaque) Part number Permissible bending radius 4 mm Flexible (R4) Ideal for mounting on moving sections (R4) Free-cut 1.0-mm dia. (0.03-mm dia.) E32-T11 E3X-NA@F E3X-NA@ (V) E3X-NAG@ M3 screw 1.0-mm dia. (0.2-mm dia.) 0.5-mm dia. (0.03-mm dia.) E32-T21 18 30 100 E3X-NA@F E3X-NA@ (V) E3X-NAG@ 1.5-mm dia. 0.5-mm dia. (0.1-mm dia.) 0.5-mm dia. (0.03-mm dia.) E32-T22B 18 30 E3X-NA@F M4 Free-cut E3X-NA@ (V) E3X-NAG@ M4 screw 280 (2,100) 50 (375) 80 (600) 0.5-mm dia. (0.1-mm dia.) 1.0-mm dia. (0.03-mm dia.) E32-T11R 1 mm E3X-NA@F 3-mm dia. Free-cut E3X-NA@ (V) E3X-NAG@ 3-mm dia. 280 (2,100) 50 (375) 80 (600) 1.0-mm dia. (0.2-mm dia.) 1.0-mm dia. (0.03-mm dia.) E32-T12R E3X-NA@F M3; small diameter Free-cut E3X-NA@ (V) E3X-NAG@ M3 screw 60 12 18 60 18 240 45 70 1.0-mm dia. (0.2-mm dia.) 0.5-mm dia. (0.03-mm dia.) E32-T21R 1 mm E3X-NA@F 2-mm dia.; small diameter Sideview Long distance; spacesaving Free-cut E3X-NA@ (V) 2-mm dia. E3X-NA@F E3X-NA@ (V) Free-cut 3-mm dia. 1.0-mm dia. (0.1-mm dia.) 0.5-mm dia. (0.03-mm dia.) 0.5-mm dia. (0.1-mm dia.) 1.0-mm dia. (0.03-mm dia.) E32-T22R 1 mm E32-T14L 25 mm E3X-NAG@ E3X-NA@F Spacesaving Free-cut 3-mm dia. E3X-NA@ (V) E3X-NA@F 33 110 Suitable Free-cut for detecting minute sensing targets Suitable for Free-cut detecting minute sensing targets Screwmounting type Free-cut E3X-NA@ (V) 1-mm dia. 90 12 27 30 9 1.0-mm dia. (0.2-mm dia.) 1.0-mm dia. E32-T14LR (0.03-mm dia.) 1.0-mm dia. (0.2-mm dia.) 0.5-mm dia. (0.03-mm dia.) E32-T24 1 mm 10 mm E3X-NAG@ E3X-NA@F 1-mm dia. E3X-NA@ (V) E3X-NA@F E3X-NA@ (V) E3X-NAG@ E3X-NA@F 1,800 330 540 0.5-mm dia. (0.3-mm dia.) 0.5-mm dia. E32-T24R (0.03-mm dia.) 0.5-mm dia. (0.3-mm dia.) 4.0-mm dia. (0.03-mm dia.) E32-T14 1 mm 25 mm 4.0-mm dia. (0.2-mm dia.) 18 E3X-NA Application Features Appearance Applicable Amplifier Unit E3X-NA@ (V) E3X-NAG@ 5-mm dia. 300 480 E3X-NA Sensing distance (mm) (Values in parentheses: when using the E39-F1 Lens Unit) Standard object (see notes) (min. sensing target: opaque) Part number Permissible bending radius 40 mm Chemicalresistant Teflon-covFree-cut ered *1; withstands chemicals and harsh environments (operating ambient temperature:-30C to 70C) 4.0-mm dia. (0.2-mm dia.) E32-T12F E3X-NA@F E3X-NA@ (V) 5-mm dia. 4.0-mm dia. (0.7-mm dia.) 3.0-mm dia. (0.2-mm dia.) Teflon-covFree-cut ered *1; sideview; withstands chemicals and harsh environments (operating ambient temperature: -30C to 70C) Teflon *1; withstands chemicals and harsh environments (operating ambient temperature: -40C to 200 C) 200 37 60 350 100 E32-T14F E3X-NAG@ E3X-NA@F E3X-NA@ (V) 3.0-mm dia. (0.7-mm dia.) 1.0-mm dia. (0.2-mm dia.) 1.0-mm dia. (0.5-mm dia.) 1.0-mm dia. (0.2-mm dia.) 1.0-mm dia. (0.5-mm dia.) 400 E32-T81F 10 mm 6-mm dia. E3X-NA@F E3X-NA@ (V) Heatresistant Resists 200C; flexible (R10); fiber sheath material: Teflon *1 (operating ambient temperature: - 40C to 200 C) Resists Free-cut 150C *2; fiber sheath material: fluororesin (operating ambient temperature: -40C to 150C) Resists 300C *3, with spiral tube; high mechanical strength; fiber sheath material: stainless steel (operating ambient temperature: -40C to 300C) Side-view; Free-cut resists 150C *2; suitable for detecting minute sensing targets; fiber sheath material: fluororesin (operating ambient temperature: -40C to 150C) 180 50 E32-T81R 10 mm M4 screw E3X-NA@F E3X-NA@ (V) 1.5-mm dia. (0.03-mm dia.) 1.5-mm dia. (1.0-mm dia.) E32-T51 35 mm M4 screw E3X-NA@F E3X-NA@ (V) 120 300 (3,000) M4 screw 1.0-mm dia. E32-T61 (0.03-mm dia.) 1.0-mm dia. (0.5-mm dia.) 1.0-mm dia. (0.03-mm dia.) 25 mm E3X-NA@F 90 E3X-NA@ (V) 2-mm dia. 130 E32-T54 35 mm E3X-NA@F 35 1.0-mm dia. (0.3-mm dia.) Resists 200C *3; L-shaped; fiber sheath material: stainless steel E3X-NA@ (V) 3-mm dia. 700 1.7-mm dia. E32-T84S (0.03-mm dia.) 1.7-mm dia. (0.4-mm dia.) 4.0-mm dia. (0.1-mm dia.) 25 mm E3X-NA@F Slot sensor Suitable for Free-cut film sheet detection; no optical axis adjustment required; easy to mount 210 E3X-NA@ (V) E3X-NAG@ E3X-NA@F 10 10 10 1,000 300 E32-G14 25 mm 4.0-mm dia. (1.0-mm dia.) 1.7-mm dia. (0.5-mm dia.) Narrow vision field Suitable for detecting wafers Free-cut E3X-NA@ (V) 3-mm dia. E32-T22S 10 mm E3X-NA@F E3X-NA@ (V) E3X-NA@F Side-view; suitable for detecting wafers Free-cut 3.5 mm dia. x 3 700 210 2.0-mm dia. (0.03-mm dia.) 2.0-mm dia. (0.5-mm dia.) E32-T24S 19 E3X-NA Application Features Appearance Applicable Amplifier Unit E3X-NA@ (V) E3X-NA@F M3 screw 90 920 170 270 E3X-NA Sensing distance (mm) (Values in parentheses: when using the E39-F1 Lens Unit) 300 Standard object (see notes) (min. sensing target: opaque) Part number Permissible bending radius 25 mm Area sensing Multi-point detection (4-head) 2.0-mm dia. E32-M21 (0.03-mm dia.) 2.0-mm dia. (0.3-mm dia.) (0.5-mm dia.) *4 Detects in a 30-mm area Free-cut E3X-NA@ (V) E3X-NAG@ 30 mm E32-T16W 10 mm E3X-NA@F Detects in a 30-mm area; flexible (4.0-mm dia.) *4 690 Free-cut E3X-NA@ (V) (0.5-mm dia.) *4 (4.0-mm dia.) *4 E32-T16WR 1 mm 30 mm E3X-NA@F 200 Side-view; Free-cut suitable for applications with limited spatial depth E3X-NA@ (V) E3X-NAG@ 11 mm 95 150 520 (0.3-mm dia.) *4 E32-T16J 10 mm E3X-NA@F E3X-NA@ (V) 11 mm (2.0-mm dia.) *4 390 Side-view; Free-cut suitable for applications with limited spatial depth; flexible (0.3-mm dia.) *4 (2.0-mm dia.) *4 1,500 E32-T16JR 1 mm E3X-NA@F E3X-NA@ (V) E3X-NAG@ 110 Suitable for detecting over a 10-mm area; long distance Free-cut (0.9-mm dia.) *4 E32-T16 25 mm 275 450 10 mm E3X-NA@F E3X-NA@ (V) E3X-NAG@ 11 mm (1.5-mm dia.) *4 600 Stable for Free-cut detecting minute sensing targets in a wide area; enclosure rating: IEC 60529 IP50 Stable for Free-cut detecting minute objects in a wide area; flexible; enclosure rating: IEC60529 IP50 (0.3-mm dia.) *4 E32-T16P 10 mm 110 180 E3X-NA@F E3X-NA@ (V) 11 mm (2.0-mm dia.) *4 450 (0.3-mm dia.) *4 (2.0-mm dia.) *4 E32-T16PR 1 mm E3X-NA@F 130 *1 Teflon is a registered trademark of the Dupont Company and the Mitsui Dupont Chemical Company for their fluoride resin. *2 For continuous operation, use the products within a temperature range of -40C to 130C. *3 Indicates the heat-resistant temperature at the fiber tip. *4 These figures are for a sensing distance of 100 mm. (Diameters of sensing targets are ones at a stationary state.) Note: 1. The size of standard sensing target is the same as the fiber core diameter (lens diameter for models with lens). 2. The values of the minimum sensing target for E3X-NA@ (V) and E3X-NAG@ through-beam models indicate those obtained where the sensing distance and sensitivity are set to optimum values. 3. The value of the minimum sensing target for E3X-NA@F through-beam models indicates that obtained at the rated sensing distance with the sensitivity set to the optimum value. 20 E3X-NA I E3X-NA Fiber Units with Reflective Sensors Indicates models that allow free cutting. Models without this mark do not allow free cutting. Refer to the end of the following table for notes and precautions. Free-cut : Red light Application Features : Green light Appearance Applicable Amplifier Unit Sensing distance (mm) *1 Standard object (see note) (min. sensing target: Gold wire) Part number Permissible bending radius 25 mm Long distance M6 Free-cut E3X-NA@ (V) E3X-NAG@ M6 screw 35 65 200 250x250 (0.01-mm dia.) 50x50 (0.1-mm dia.) 100x100 (0.015-mm dia.) 150x150 (0.01-mm dia.) 25x25 (0.1-mm dia.) 50x50 (0.015-mm dia.) 100x100 (0.01-mm dia.) 25x25 (0.1-mm dia.) 25x25 (0.015-mm dia.) 100x100 (0.01-mm dia.) 25x25 (0.1-mm dia.) 25x25 (0.015-mm dia.) E32-D11L E3X-NA@F 3-mm dia.; small diameter E3X-NA@ (V) E3X-NAG@ 3-mm dia. Free-cut 120 E32-D12 20 40 50 E3X-NA@F M4 Free-cut E3X-NA@ (V) E3X-NAG@ M4 screw E32-D21L 10 mm 10 17 50 E3X-NA@F 3-mm dia.; small diameter E3X-NA@ (V) E3X-NAG@ 3-mm dia. Free-cut E32-D22L 10 17 E3X-NA@F Generalpurpose M6 E3X-NA@ (V) E3X-NAG@ M6 screw Free-cut 150 200x200 (0.01-mm dia.) 50x50 (0.1-mm dia.) 75x75 (0.015-mm dia.) 50x50 (0.01-mm dia.) 25x25 (0.1-mm dia.) 25x25 (0.02-mm dia.) E32-DC200 25 mm 25 50 E3X-NA@F M3; small diameter E3X-NA@ (V) E3X-NAG@ E3X-NA@F Thin fiber 2.5-mm dia.; with sleeve Free-cut Free-cut 36 6 12 150 E32-DC200E 10 mm M3 screw E3X-NA@ (V) 90 mm (40 mm) 200x200 (0.01-mm dia.) 50x50 (0.1-mm dia.) 75x75 (0.015-mm dia.) 50x50 (0.01-mm dia.) 25x25 (0.1-mm dia.) 25x25 (0.02-mm dia.) 25x25 (0.01-mm dia.) 25x25 (0.03-mm dia.) 25x25 (0.01-mm dia.) 25x25 (0.05-mm dia.) E32-DC200B E32-DC200B4 25 mm E3X-NAG@ M6 screw 2.5-mm dia. ( ): E32-DC200B4 25 50 E3X-NA@F E3X-NA@ (V) 1.2-mm dia.; with sleeve Free-cut 36 6 12 10 3.3 90 mm (40 mm) E32-DC200F E32-DC200F4 10 mm E3X-NAG@ M3 screw 1.2-mm dia. ( ): E32-DC200F4 E3X-NA@F E3X-NA@ (V) 0.8-mm Free-cut dia.; for detecting minute sensing targets 0.5-mm dia.; for detecting minute sensing targets 3-mm dia. 0.8-mm dia. E32-D33 4 mm E3X-NA@F E3X-NA@ E3X-NA@F 0.5-mm dia. 2-mm dia. 1.5 0.5 E32-D331 4 mm 21 E3X-NA Application Features Appearance Applicable Amplifier Unit Sensing distance (mm) *1 Standard object (see note) (min. sensing target: Gold wire) E3X-NA Part number Permissible bending radius 4 mm Flexible Ideal for mounting on moving sections Free-cut E3X-NA@ (V) E3X-NAG@ M6 screw 15 30 90 150x150 (0.01-mm dia.) 25x25 (0.1-mm dia.) 50x50 (0.015-mm dia.) 25x25 (0.01-mm dia.) 25x25 (0.02-mm dia.) E32-D11 E3X-NA@F E3X-NA@ (V) Free-cut 15 5 E32-D21 M3 screw E3X-NA@F E3X-NA@ (V) E3X-NAG@ 15 2.4 5 25x25 (0.01-mm dia.) 25x25 (0.1-mm dia.) 25x25 (0.02-mm dia.) 25x25 (0.01-mm dia.) 25x25 (0.02-mm dia.) E32-D21B Free-cut M4 screw E3X-NA@F E3X-NA@ (V) 1.5-mm dia. 7 2.3 E32-D22B E3X-NA@F E3X-NA@ (V) E3X-NAG@ M6 Free-cut 90 15 30 150x150 (0.01-mm dia.) 25x25 (0.1-mm dia.) 50x50 (0.02-mm dia.) 150x150 (0.01-mm dia.) 25x25 (0.1-mm dia.) 50x50 (0.02-mm dia.) 25x25 (0.01-mm dia.) 25x25 (0.03-mm dia.) E32-D11R 1 mm M6 screw E3X-NA@F 3-mm dia. E3X-NA@ (V) E3X-NAG@ 3-mm dia. Free-cut 90 15 30 E32-D12R E3X-NA@F M3; small diameter E3X-NA@ (V) M3 screw Free-cut 15 5 E32-D21R E3X-NA@F E3X-NA@ (V) 3-mm dia.; small diameter Free-cut 15 5 25x25 (0.01-mm dia.) 25x25 (0.03-mm dia.) E32-D22R 3-mm dia. E3X-NA@F 22 E3X-NA Application Features Appearance Applicable Amplifier Unit Sensing distance (mm) *1 Standard object (see note) (min. sensing target: Gold wire) E3X-NA Part number Permissible bending radius 25 mm Coaxial M6coaxial; highprecision positioning Free-cut E3X-NA@ (V) E3X-NAG@ M6 screw 25 50 150 200x200 (0.01-mm dia.) 50x50 (0.1-mm dia.) 75x75 (0.015-mm dia.) E32-CC200 E3X-NA@F 3-mm dia. Free-cut coaxial; small diameter; highprecision positioning E3X-NA@ (V) E3X-NAG@ 3-mm dia. 80 12 25 40 6 13 100x100 (0.01-mm dia.) 25x25 (0.1-mm dia.) 50x50 (0.02-mm dia.) 50x50 (0.01-mm dia.) 25x25 (0.1-mm dia.) 25x25 (0.02-mm dia.) 25x25 (0.01-mm dia.) 25x25 (0.02-mm dia.) 25x25 (0.01-mm dia.) 25x25 (0.02-mm dia.) E32-D32L E3X-NA@F M3 coaxial; Free-cut highprecision positioning; possible to mount small-spot lens (E39-F3A-5/ F3B/F3C) M3 coaxial; highprecision positioning; possible to mount small-spot lens (E39-F3A-5/ F3B/F3C) 2-mm dia. coaxial; high-precision positioning; possible to mount small-spot (0.1 to 0.6 dia.) lens (E39-F3A) 2-mm dia. Free-cut coaxial; highprecision positioning; possible to mount small-spot (0.5 to 1 dia.) lens (E39-F3A) Side-view 6-mm dia.; long distance Free-cut E3X-NA@ (V) E3X-NAG@ E3X-NA@F E3X-NA@ (V) M3 screw E32-C31 M3 screw 15 E32-C41 E3X-NA@F E3X-NA@ (V) 5 15 E32-C42 2-mm dia. E3X-NA@F 5 E3X-NA@ (V) E3X-NAG@ 2-mm dia. 6 40 50x50 (0.01-mm dia.) 25x25 (0.1-mm dia.) 25x25 (0.02-mm dia.) 50x50 (0.03-mm dia.) 25x25 (0.3-mm dia.) 25x25 (0.03-mm dia.) 25x25 (0.03-mm dia.) E32-D32 E3X-NA@F E3X-NA@ (V) 6-mm dia. 13 40 E32-D14L 25 mm E3X-NAG@ E3X-NA@F 10 13 16 6-mm dia.; flexible Free-cut E3X-NA@ (V) 6-mm dia. E32-D14LR 1 mm E3X-NA@F 2-mm dia.; small diameter; flexible, space-saving Free-cut 5 E3X-NA@ (V) 2-mm dia. 15 2.4 5 25x25 (0.03-mm dia.) 25x25 (0.3-mm dia.) 25x25 (0.03-mm dia.) 25x25 (0.03-mm dia.) E32-D24 10 mm E3X-NAG@ E3X-NA@F 2-mm dia.; Free-cut small diameter space-saving; flexible Chemicalresistant TeflonFree-cut covered *3; withstands chemicals and harsh environments (operating ambient temperature: -30C to 70C) E3X-NA@ (V) 2-mm dia. 7 2.3 50 8 16 E32-D24R 1 mm E3X-NA@F E3X-NA@ (V) E3X-NAG@ 6-mm dia. 100x100 (0.03-mm dia.) 25x25 (0.3-mm dia.) 25x25 (0.03-mm dia.) E32-D12F 40 mm E3X-NA@F 23 E3X-NA Application Features Appearance Applicable Amplifier Unit Sensing distance (mm) *1 Standard object (see note) (min. sensing target: Gold wire) E3X-NA Part number Permissible bending radius 35 mm Heatresistant Resists 150C Free-cut *2; fiber sheath material: fluororesin (operating ambient temperature: -40C to 150C) E3X-NA@ (V) M6 screw 120 150x150 (0.03-mm dia.) 50x50 (0.03-mm dia.) 100x100 (0.03-mm dia.) 25x25 (0.03-mm dia.) 50x50 (0.03-mm dia.) E32-D51 E3X-NA@F E3X-NA@ (V) 40 Resists 300C *4; fiber sheath material: stainless steel (operating ambient temperature: -40C to 300C) Resists 400C *4; fiber sheath material: stainless steel (operating ambient temperature: -40C to 400C) 45 E32-D61 25 mm M6 screw E3X-NA@F E3X-NA@ (V) 15 E32-D73 30 1.25-mm dia. M4 screw E3X-NA@F 10 25x25 (0.03-mm dia.) Area sensing Side-view; detection over wide areas Free-cut E3X-NA@ (V) E3X-NA@F M6 screw Reflector E39-R3 75 25 100x100 (0.03-mm dia.) 50x50 (0.03-mm dia.) 10 to 250 10 to 250 E32-D36P1 25 mm Retroreflective Transparent object detection; polarized Free-cut E3X-NA@ (V) E3X-NA@F E3X-NA@ (V) 35-mm dia. (0.3-mm dia.) 35-mm dia. (0.5-mm dia.) 35-mm dia. 150 (0.6-mm dia.) to 1,500 35-mm dia. 150 to (4.0-mm dia.) 1,000 E32-R21 +E39-R3 (Attachment) 10 mm Transparent Free-cut object detection, polarized (operating ambient temperature: -25C to 55C); enclosure rating: IEC 60529 IP66 E32-R16 +E39-R1 (Attachment) 25 mm Reflector E39-R1 E3X-NA@F Limited reflective Suitable for positioning crystal glass Free-cut E3X-NA@ (V) E3X-NA@F E3X-NA@ (V) E3X-NA@F E3X-NA@ (V) E3X-NA@F E3X-NA@ (V) E3X-NA@F E3X-NA@ (V) E3X-NA@F 4 to12 4 to12 42 42 7.21.8 7.21.8 3.3 3.3 3.3 3.3 --- E32-L56E1 E32-L56E2 35 mm Detects Free-cut wafers and small differences in height; (operating ambient temperature: -40C to 105C); enclosure rating: IEC 60529 IP50 Detects Free-cut wafers and small differences in height; enclosure rating: IEC 60529 IP50 25x25 (0.015-mm dia.) 25x25 (0.03-mm dia.) 25x25 (0.015-mm dia.) 25x25 (0.03-mm dia.) 25x25 (0.015-mm dia.) 25x25 (0.03-mm dia.) 25x25 (0.015-mm dia.) 25x25 (0.03-mm dia.) ----- E32-L24L 10 mm E32-L25L E32-L25 25 mm E32-L25A Fluidlevel detection Fluid contact type: unbendable section L 150 mm, 350 mm (two types) Tubemounting type Free-cut E3X-NA@ (V) L --- E32-D82F1 E32-D82F2 40 mm E3X-NA@F E3X-NA@ (V) E3X-NA@F --- ----- E32-L25T 10 mm *1 Sensing distance indicates values for white paper. *2 For continuous operation, use the products within a temperature range of -40C to 130C. *3 Teflon is a registered trademark of the Dupont Company and the Mitsui Dupont Chemical Company for their fluoride resin. *4 Indicates the heat-resistant temperature at the fiber tip. Note: The values of the minimum sensing target indicate those obtained at a distance where the smallest object can be sensed with the Reflective Fiber Unit. 24 E3X-NA E3X-NA 25 E3X-NA E3X-NA 26 E3X-NA E3X-NA 27 E3X-NA E3X-NA ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ELECTRONICS LLC One East Commerce Drive Schaumburg, IL 60173 OMRON ON-LINE Global - http://www.omron.com USA - http://www.omron.com/oei Canada - http://www.omron.com/oci OMRON CANADA, INC. 885 Milner Avenue Scarborough, Ontario M1B 5V8 1-800-55-OMRON Cat. No. E318-E3-1 10/01/7.5M 416-286-6465 Printed in USA Specifications subject to change without notice 28 |
Price & Availability of E3X-NA8 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |